Panasonic GP-KS162CUD User Manual

Page 1
Camera Control Unit
GP-KS162CUD
(Lens, Cable and Camera Head : option)
Before attempting to connect or operate this product, please read these instructions completely
Page 2

CONTENTS

PREFACE .............................................................................................................................................................................................. 1
FEATURES ............................................................................................................................................................................................ 1
SYSTEM BLOCK DIAGRAM ................................................................................................................................................................. 3
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS .............................................................................................................. 3
PREPARATIONS ................................................................................................................................................................................... 6
SPECIFICATIONS ................................................................................................................................................................................ 7
OPTIONAL ACCESSORIES .................................................................................................................................................................. 7
CAUTION:
Before attempting to connect or operate this product, please read the label on the bottom.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SER­VICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PER­SONNEL.
The lightning flash with arrowhead sym­bol, within an equilateral triangle, is intended to alert the user to the pres­ence of uninsulated "dangerous voltage" within the product's enclosure that may
SA 1965
SA 1966
be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilat­eral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompa-nying the appli­ance.
For U.S.A
Warning: This equipment generates and uses radio frequency ener­gy and if not installed and used properly, i.e., in strict accordance with the instruction manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
The serial number of this product may be found on the bot­tom of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft.
Model No. Serial No.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Page 3

PREFACE

FEATURES (With GP-KS162 H)

The Panasonic Camera Control Unit GP-KS162CU is designed to use with the optional Camera Head GP­KS162H. This system overcomes space limitations that have compli­cated many video applications. Weight of only 0.04 lbs (16 g), this remarkably compact CCTV camera measures only two-thirds of an inch in diameter and less than two inches in length. GP-KS162CU Remote Control Unit (CCU) and optional camera head GP-KS162H can be extended up to 33 feet(10-meter) away, using an optional 33-feet (10­meter) cable. So the exceptionally manueurable GP-KS162 series lets you obtain a whole new world of camera angles and shots that were once quite difficult to achieve. With the 380,000-element, 1/2-inch CCD pick-up device, horizontal resolution is more than 480 lines, and signal-to-noise ratio is 50 dB. An Auto Light Selection Switch and lets you obtain clear, high-quality color images in light as low as 0.3 foot­candle (3 lux at F1.4). In addition, a small diameter wide-angle lens developed by Matsushita makes high resolution standard even with sub­jects as close as 4/5th of an inch away. Color changes are sensed instantly and compensated for by a microcomputer in the GP-KS162CU. Proper white bal­ance is then obtained via the built-in-Auto Tracing White Balance (ATW) circuit. Both White Balance and R and B color can also be adjusted manually, for optimum color reproduction. The camera head can be used with most existing camera systems. And VTR, video printer or floppy disk recorder, for a host of new and traditional applications.
1. 1/2 inch Interline CCD image sensor with 768 (H) x 492 (V) pixels.
2. 480 lines of horizontal resolution.
3. 0.3 footcandle (3 lux) at F1.4 of minimum scene illumi­nation.
4. 50 dB of signal to noise ratio.
5. Selectable trough the Lens Auto Tracing White Balance (ATW), Auto White Balance Control (AWC) or Manual White Balance Control.
6. Auto Light Control Switch enables to control the video output level to constant level whatever the object brightness may be.
7. Video Level Control enables to adjust the video level to your preference.
8. The preset 1, preset 2 and automatic setting mode are provided for Back Light Compensation (BLC) function.
9. 2-memory AWC mode is available.
10. DC 12V operation
11. 33-feet (10-meter) of maximum cable length between camera head and camera control unit with optional camera cable.
12. S-VHS Video Output is provided.
-1-
Page 4

PRECAUTIONS

• Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or cover. There are no user-serviceable parts inside. Refer servicing to qualified service personnel.
• Do not expose the camera or camera control unit to rain or moisture, or do not try to operate it in wet areas. Do take immediate action if ever the camera or camera control unit do become wet. Turn power off and refer servicing to qualified service personnel. Moisture can damage the camera and camera control unit and also create the danger of electric shock.
• Ambient Temperature range Do not install the camera in the place which is beyond 14 °F - 104 °F (10°C - +40 °C).
• Do not drop anything inside the camera. Dropping metal for example inside the camera could permanently damage the unit.
• How to take care of this camera. After turning OFF the Power ON/OFF Switch, clean it with a dry cloth. If it is difficult to remove the dirt or dust, clean it up with a cloth applied the neutral cleanser. Use the lens cleaning tissue paper(may be available at your local camera store) for lens cleaning.
• Connect this to a DC12V, 0.5 A - 0.7 A CLASS 2 Power supply only.
• After using the camera, turn OFF the power ON/OFF Switch and put the lens cap on the camera head.
• Every necessary procedures with regard to install this product should be made by qualified service person­nel or system installers.
• Never crush or pinch the camera cable. Do not bend the camera cable into a curve whose radius is too small.
• Never face the camera is in use, never face it toward the sun.
• Never face the camera toward the sun whether the camera is in use or not, never face it toward the sun. Do use caution when operating the camera in the vicin­ity of spot lights or other lights and light reflecting objects.
Caution:
Connecting or disconnecting camera cable to/from the camera control unit must be done after turning OFF the Power ON/OFF Switch. Otherwise, the camera head may be damaged.
-2-
Page 5
FOCUS LOCK
Panasonic
GP-KS162H

SYSTEM BLOCK DIAGRAM

MANU
OFF
VIDEO LEVEL
ON
OFF
AUTO
LIGHT AWC ATW
MANU
WHITE
BAL
LEVELBR
AWC SET
DC POWER
ON
OFF
CAMERA
GP-
KS162
VIDEO OUT 1
VIDEO OUT 2
S-VIDEO OUT
DC 12V IN
F
O
C
U
S
L
O
C
K
Panasonic
GP-KS162H
MANU
OFF
VIDEO
LEVEL ON OFF
AUTO
LIGHT AWC ATW
MANU
WHITE
BAL
LEVELBR
AWC SET
DC POWER
ON
OFF
CAMERA
GP-
KS162
GP-KS162 Series Standard Configuration
Camera Head, Tripod Attachment, Camera Control Unit.
Optional Camera Cable GP-CA162/2: 2m GP-CA162/3: 3m GP-CA162/38: 3.8m GP-CA162/10: 10m
Optional Camera Head (GP-KS162H)
Optional Accessorles
Wide Angle Lens GP-LM3TA
Pinhole Lens GP-LP12TA
C-Mount Adaptor GP-AD22TA
Wide Angle Lens GP-LM7TA
Tele Angle Lens GP-LM15TA
Tele Angle Lens GP-LM24TA

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

Camera Control Unit GP-KS162CU

q w e r y u o !4 !6 !8 @0
!5 !7 !9 @1
Camera Control Unit GP-KS162CU
!2 !0
t i !3 !1

Optional Camera Head GP-KS162H with Optional Lens GP-LM7TA

#1 #2 #3
-3-
Page 6

Camera Control Unit GP-KS162CU

423
1
1. DC Power On/Off Switch (DC POWER, ON/OFF)
2. Auto White Balance Control Button (AWC SET)
The white balance can be set by pressing this button when the White Balance Selection Switch (4) is set to the AWC position.
3. White Balance Indicator
4. White Balance Selection Switch (WHITE BAL, AWC/ATW/MANU) AWC : The white balance is automatically set and
fixed by detecting the characteristic / color temperature of light source through the lens and controlling the gain of red and blue signal. The White Balance Indicator lights during the setting. Note: When the White Balance Offset On/Off
Switch is turned on, the fine adjustment for R/B gain is available by means of the R and B Gain Controls (5) after completing the white balance setting. The adjustable range is approx. 2,200K - 10,000K.
ATW : The white balance is automatically and contin-
uously set by detecting the characteristic / color temperature of light source through the lens and controlling the gain of red and blue signal even if the characteristic / color temper­ature varies. Note: When the White Balance Offset On/Off
Switch is turned on, the fine adjustment for R/B gain is available by means of the R and B Gain Controls after completing the white balance setting. The adjustable range is approx. 2,300K - 6,000K.
MANU: The R/B gain of the white balance can be
adjusted manually by means of the R and B Gain Controls. The adjustable range of the white balance temperature is approx. 2,200K - 10,000K.
5. R / B Gain Controls (R/B)
These controls are used to adjust the R and B gain of the white balance.
6. Auto Light On/Off Switch (AUTO LIGHT ON/OFF) ON: When this switch is set to the ON position, the
video signal is set to the best level with the combi­nation of the Electronic light Control On/Off Switch(14) and AGC On/Off Switch(15).
8. Video Level Control (LEVEL)
This controls the video level when the Video Level Selection Switch (7) is set to the MANU position. The video level control depends on the Auto Light On/Off Switch (6) setting as shown below.
AUTO LIGHT OFF :
By turning this counterclockwise, the video level is decreased. By turning this clockwise, the video level is increased. The video level setting at the center position of this control is higher than the standard one.
AUTO LIGHT ON :
By turning this counterclockwise, the standard video level is decreased. By turning this clockwise, the standard video level is increased. The standard video level setting at the center posi­tion of this control is higher than standard one.
9. Camera Cable Connector (CAMERA)
This 16-pin connector is used for connection of the optional camera cable. Caution: Connecting or disconnecting the camera
cable must be done after turning OFF the Power ON/OFF Switch.
10. S-Video Output Connector (S-VIDEO OUT)
The luminance (Y) and chroma (C) signals for S-VHS VCR or monitor are provided at this connector.
Pin Configuration
Pin No. Description
1. Y Ground
2. C Ground
3. Y Signal Output: 0.714 Vp-p (Y level/75 ohms)
4. C Signal Output: 0.286 Vp-p (burst Level/75 ohms)
11. EVR Adjustment Connector
This connector is used to connect with the EVR.
12. Video Output Connectors (BNC)(VIDEO OUT 1,2)
A 1.0 Vp-p ohms composite video signal is provided at this connector.
7. Video Level Selection Switch (VIDEO LEVEL, MANU/OFF)
This switch is used to select the Video Level. OFF: When this switch is set to the OFF position, the
video signal is supplied with the standard level.
MANU: When this switch is set to the MANU position,
the video level is adjustable by means of the Video Level Control (8).
Note:
This switch can be used as the Gain Up/Down Switch due to the value set by the Video Level Control (8).
13. DC 12V Input Terminals (DC 12V IN)
These terminals accept an external DC source supply­ing nominal power of 12V, 0.5A - 0.7A. CAUTION: CONNECT THIS TO A DC 12V CLASS 2
POWER SUPPLY ONLY.
Caution: To prevent fire or shock hazard, the UL listed
wire VW-1 style 1007 should be used for the cable for DC 12V Input Terminal.
-4-
Page 7
14. Electronic Light Control (ELC) On/Off Switch
AWC ATW
MANU
WHITE
BAL
When shooting the objects under the high light condi­tion, the lighting can be controlled by the electronic shutter mode. This switch is used to disable the ELC function. Normally turn on this switch.
15. AGC On/Off Switch
on off
When shooting the objects under the low light condi­tion, the video level can be controlled by the gain of the video amplifier. This switch is used to disable the AGC function. Normally, turn on this switch. In the Auto Light On mode, the setting mode is differ­ent by the combination of ELC On/Off switch (14) and AGC On/Off switch (15) as shown below.
ELC On/Off Switch (14)
On Off
AGC On/Off
Switch (15)
On
Off
ELC On
AGC On
ELC On
AGC Off
ELC Off
AGC On
Auto Light Function
is disable
on off
This function is invalided by setting the white balance again. In the AWC mode, the Automatic Sensing Zone setting is available.
20. Aperture Level Selection Switch
on off
The aperture level can be selected by this switch. High level can be obtained by turning on this switch. Low level can be obtained by turning off this switch.
on
21. Cable Selection Switch
off
This switch is provided for optional cable GP­CA162/38 and GP-CA162/10. CAUTION:BE SURE TO TURN ON THIS SWITCH
BEFORE TURNING ON THE POWER. When using the optional cable GP-CA162/2 and GP­CA162/3, turn off this switch.
Camera Head GP-KS162H (Option)
31. Manual Iris Control Ring
This ring is used to adjust the lens iris manually.
16. White Balance Offset On/Off Switch
on off
By turning on this switch, the white offset in the AWC/ATW can be adjusted fine by using the R/B Gain Controls (5). Usually, turn off this switch.
17. 2-Memory AWC Mode On/Off Switch
on off
By turning on this switch, the two kinds of white bal­ance can be memorized. The function of the White Balance Selection Switch is changed as shown below by turning on this switch.
By turning on this switch
AWC 1 AWC 2
18/19. Back Light Control (BLC) Mode Selection Switch
The back light sensing zone can be set in the Auto Light On mode. 00: BLC OFF (All of the screen) 01: BLC Preset 1 (Pattern 1 Sensing Zone) 10: BLC Preset 2 (Pattern 2 Sensing Zone)
32. Focus Ring
This ring is used to adjust the focus of the picture. To adjust the focus, loosen the Focus Lock Ring (33) by rotating it clockwise (viewed from the front of the cam­era) and turn the Focus Ring until picture becomes the best resolution. Secure the Focus Ring by rotating the Focus Lock Ring(33) counterclockwise.
33. Focus Lock Ring
This ring is used to secure the Focus Ring.
on off
Sensing
Zone
BLC Preset 1 BLC Preset 2
11: Automatic Sensing Zone
The Automatic Sensing Zone setting works effec­tively against the optical shading around the screen in an optical instrument use. In this case, this camera sets the sensing zone automatically when the AWC has been set with the white objects.
-5-
Page 8

PREPARATIONS

Caution: Keep the Power ON/OFF Switch of the camera in
the OFF position through the installation.
GP-KS162H with GP-LM3TA, GP-LM7TA, GP-LM15TA or GP-LP12TA
1. Remove the front cap of the camera and confirm that the surface of the optical filter of the camera head is clean.
Front Cap
If the surface of the optical filter is dirty or dusts are on it, clean it up with a blower brush which is for film cam­era lenses (may be available at your local camera store) or supplied lens cleaning tissue paper.
2. Rotate the focus lock ring fully clockwise. Mount the Pinhole Lens, Wide-angle Lens or Super Wide-angle Lens to the camera by rotating it clockwise slowly.
GP-KS162H with GP-AD22TA and optional C-mount lens
1. Remove the front cap of the camera head and confirm that the surface of the optical filter of the camera head is clean.
Front Cap
If the surface of the optical filter is dirty or dusts are on it, clean it up with a blower brush which is for film cam­era lenses (may be available at your local camera store) or supplied lens cleaning paper.
2. Attach the optional C-mount lens to the C-mount Adaptor GP-AD22TA by rotating it clockwise.
Focus Lock Ring
3. Rotate the focus lock ring fully Mount the lens and C-mount adaptor by rotating them clockwise slowly.
Focus Lock Ring
Caution: If the optional C-mount lens size exceeds
2”(50.8 mm) in diameter, 2-3/4” (70 mm) in length and 0.66 lbs (300g) in weight, both the camera and lens should be secured.
-6-
Page 9

SPECIFICATIONS(with the combination of Optional Camera Head GP-KS162H)

Pick-up Device : 1/2-inch Interline transfer CCD image sensor with 768 (H) x 492 (V) pixels Horizontal Resolution : 480 lines
Minimum Scene Illumination : 0.3 footcandles (3 lux) (F1.4 with AGC ON more than 30 IRE of Y signal with set up)
0.5 footcandles (5 lux) (F1.6 with AGC ON more than 30 IRE of Y signal with set up) Signal to Noise Ratio : 50 dB (Standard condition, Y signal) Video Output : 1.0 Vp-p/75 ohms, composite video, BNC connector x 2) Scanning System : 2:1 Interlace Synchronization : Internal Sync only White Balance : Auto Tracing White Balance(ATW)/Auto White Balance Control(AWC)/Manual(MANU) Gain Control : Auto Light On/Off, Video Level(Off/Manual) Switches : White Balance Mode (ATW/MANU/AWC), AWC SET(SET), Auto Light ,
Video Level(Off/Manual) Controls : R,B gain, VIDEO Level Power Source : 12V DC, 300 mA Camera Cable Length : GP-CA162/2 Cable 6.6 feet(2-meter), GP-CA162/3 Cable 9.9 feet (3-meter),
GP-CA162/38 Cable 12.5 feet (3.8-meter), GP-CA162/10 Cable 33 feet(10-meter) Ambient Temperature : 14°F - 104°F (−10°C - +50°C) Dimensions : Camera Head : 2/3” (Diameter) x 1-1/2”(D), (17(Diameter) x 35.5 (D) mm)
Camera Control Unit : 4-11/16”(W) x 1-7/16”(H) x 6-1/8”(D)
(120 (W) x 36 (H) x 157 (D) mm)
Weight : Camera Head : 0.035 lbs (14 g)
Camera Control Unit : 1.2 lbs (550 g)
Weight and dimensions indicated are approximate. Specifications are subject to change without notice.

Optional Accessories

.
• Camera Cable GP-CA162/2, GP-CA162/3, GP-CA162/38 or GP-CA162/10 . • C-mount Adaptor GP-AD22TA . • Wide Angle Lens GP-LM3TA or GP-LM7TA . • Pinhole Lens GP-LP12TA . • Tele Angle Lens GP-LM15TA or GP-LM24TA
• Camera Head GP-KS162H
-7-
Page 10
Broadcast & Television Systems Company
Division of Matsushita Electric Corporation of America
INDUSTRIAL CAMERA DIVISION
Executive Office: One Panasonic Way 4H-2, Secaucus, New Jersey 07094 (201) 392-6674
MATSUSHITA ELECTRIC OF CANADA LIMITED
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905) 624-5010
PANASONIC SALES COMPANY DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.
San Gabriel Industrial Park, 65th Infantry Ave. KM. 9.5 Carolina, Puerto Rico 00630 (809) 750-4300
N0695-0 YWV8QA4086AN Printed in Japan
N 13
Loading...