Panasonic EP30006 User Manual

Household

Massage Lounger

Sillón de Masaje Doméstico

Operating Instructions

Instrucciones de Uso

Model No./Nº de Modelo EP30006

Before operating this unit, please read these instructions completely.

Antes de utilizar esta unidad, lea compleatamente estas instrucciones y guárdelas para referencia futura.

IMPORTANT SAFETY INSTRUCTIONS

Basic precautions should always be followed when using an electrical unit, including the following.

Please ensure that you read all instructions before using the Household Massage Lounger.

DANGER – To reduce the risk of electric shock:

1. Always unplug this unit from the electrical outlet immediately after using and before cleaning.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Always insert the power plug all the way into the outlet to reduce the risk of short-circuit and fire.

2. The unit should never be left unattended when plugged in. Always unplug the unit when not in use.

3. The unit is not to be used by people who cannot move or communicate on their own.

4. Only use the unit for the purpose described in these instructions.

5. Do not stand on the unit.

6. Do not use any accessories other than those recommended by the manufacturer.

7. Always return the seat to the upright position and make sure the legrest is completely retracted. Be careful that
nothing is obstructing the legrest while retracting. Keep children away from the legrest.

8. Never operate the unit if it has a damaged power cord or plug. Return the unit to the nearest authorized service
center if it is not working properly, if it has been dropped or damaged, or if it has been immersed in water.

9. Keep power cords away from heated surfaces. Do not carry the unit by the power cord.

10. Never block the air openings during operation and make sure that all air openings are kept free of lint and hair,
etc. Do not drop or insert anything into any of the openings of the unit.

11. Do not use the unit on top of heating appliances, such as electric carpets, etc. Do not operate the unit under
blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.

12. Do not use the unit in bathrooms or other damp or humid places as this may cause electric shock or cause the
unit to malfunction. Do not spill water, etc. onto the control panel.

13. Do not use the unit outdoors.

14. Do not use or operate where aerosol spray products are being used or where oxygen is being administered.

15. When unplugging the unit, turn off all controls before removing the plug from power outlet. Do not use the unit
with a transformer as this may lead to malfunction or electric shock.

16. Connect this unit to a properly grounded outlet only. See Grounding Instructions.

SAVE THESE INSTRUCTIONS

1

SAFETY PRECAUTIONS

CAUTION: To avoid the risk of injury:

1. Persons with any of the conditions listed below or who are undergoing medical treatment or suffer from medical
conditions should consult with their physicians before using the unit:

a) Pregnant women, people who are ill, in poor physical shape.
b) People suffering from back, neck, shoulder, or hip pain.
c) People who have a pacemaker, defibrillator, or other personal medical devices prone to electronic

interference.
d) People suffering from heart disease.
e) People who are prohibited from receiving massage by a physician due to thrombosis or aneurism, acute

varicose veins, or other circulatory disorders.
f) People with irregular curvatures of the spine.

2. This unit should not be used by children. Remove the key when not in use and store out of reach of children.

3. Sit down slowly after checking the position of the massage heads. Never put any part of your body between the
massage heads as the squeezing action of the massage heads may cause injury. Never put your fingers or feet
in the gap between the backrest and seat, the backrest and the armrest, the seat and cover under the armrest,
or the gap between the legrest and the footrest. Do not place your fingers or any part of your body in the
mechanism below the legrest, or between the legrest and footrest.

4. Do not use the unit against bare skin. While thin clothing may increase effectiveness, exposing the skin directly
to the massager may irritate the skin.
Do not use the unit while wearing anything hard on your head like a hair accessory, etc. Do not use the unit for
massaging the head, abdomen, front neck, elbows or knees.
Do not use excessively strong massage action on the back of the neck.

5. When using the body scanning function, always ensure that the shoulder position is correct. If the shoulder
position is not correct, use the POSITION button to adjust it properly. You can adjust the shoulder position in this
way in the pre-programs, quick massage, self-program and manual operation. Failure to align the shoulder
position correctly can lead to injury.

6. Do not stretch the back muscles for more than approximately 15 minutes at a time. To avoid overstretching the
muscles which may result in discomfort, do not use the unit for more than 5 minutes when first using it. You can
gradually increase the duration and strength of the massage as you become used to it.
Do not massage any one point for more than 5 minutes at a time.
Excessive massaging can overstimulate the muscles and nerves and result in an adverse effect.
To prevent excessive massaging, do not use the massager for more than a total of 15 minutes each session.
After approximately 15 minutes, the massage heads will be retracted and stop moving.
The back cushion can be removed if you want to experience a stronger back massage. Exercise extreme care
when you use this mode in order to avoid back pain or injury. Use only for short periods of time (no more than
15 minutes). Reinstall the back cushion if you want to restore to normal massage intensity.

7. While using the massager, if you start feeling sick or if the massage seems painful, stop using it immediately.
While using the massager, if the pressure seems too strong, the movement of the massage heads can be
stopped at any time by pressing the Quick Stop button.

8. Do not go to sleep while using the unit. Do not use the unit after drinking alcohol.

9. When the seat back is in a reclined position, do not sit on it or sit with your legs resting on the headrest.
Do not sit on the legrest as the unit may fall over.

10. Do not allow children or pets to play on or around the unit, especially during operation.

11. Do not unplug the unit or turn it off during operation. Unplug the unit immediately if there is a power outage.

12. Be sure to start on the gentle massage program if using the massager for the first time. The shiatsu massage is
stronger and should be enjoyed after one has gotten accustomed to the chair.

13. Do not allow children to play on this mechanized furniture or operate the mechanism. Legrest folds down on
closing so that a child could possibly be injured. Always leave in an upright and closed position. Keep hands and
feet clear of mechanism. Only the occupant should operate it.

14. Remove hard objects, such as false fingernails, wristwatches or rings, when massaging hands or arms.
Empty pockets of hard objects when massaging the area of the seat or thighs.

15. Always raise the back cushion to check that the fabric of the unit itself has not been ripped before using the unit.
Please also check other areas to ensure that the fabric has not been ripped. No matter how small the rip, if you
find one then immediately stop using the unit, unplug the power cord and have the unit repaired at an authorized
service center.

2

OPERATING PRECAUTIONS

WARNING: To avoid damaging the chair, follow these precautions:

1. The chair is designed for a maximum user weight of 264 lbs (120 kg). Exceeding the maximum weight may
cause permanent damage to the massage mechanism and/or other components of the unit. Any such damage
is deemed to be user abuse and is not covered under the Limited Warranty.

2. Do not sit on or drop the control panel. Do not pull the control panel cord or the power cord. Be careful not to
catch the cord of the control panel between the armrest and the chair back.

3. Do not treat the chair roughly, such as turning the chair on its side, turning the chair over or standing on it.

4. Do not treat the covering roughly.

Keep sharp or pointed objects away from the covering of the chair. Be careful not to drop lit ashes, lit cigarettes

•

or matches on the chair.
Exposure to direct sunlight can cause fading or a change in color of the covering.

•

5. If the massager functions abnormally, immediately turn off the power and have the massager checked by an
authorized service center.

6. Do not repeatedly operate any switch at short intervals. Such action may cause the switch to malfunction.

7. Some noise may be heard coming from the massager while in use. This is due to the structure of the massager
and is normal.

8. Make sure there are no obstacles behind the chair before reclining it. The chair can be reclined to a maximum
angle of 170˚. If the back hits a wall or pillar, the chair may malfunction. Be sure to have ample space behind the
chair. Recline the chair slowly in order to avoid contact with an obstacle.

9. When excessive pressure is applied to the massage heads, they may stop moving for safety. When moving the
heads up from the lowered position, one’s body weight may stop the heads’ movement. In such a case, slightly
raise your body and allow the massage heads to move up.

10. After each massage, slide the power switch, which is located on the right side of the chair, to the “off” position
and turn its lock switch to the “lock” position.

11. Do not sit on the chair with wet body or hair.

12. The unit must not be used in “wet rooms” (sauna, swimming pool) or outdoors.

13. Do not attempt to open or disassemble any part of the unit. Only use an authorized Panasonic servicer to fix
your unit. Call 1-800-338-0552 to find the servicer nearest to you.

3

GROUNDING INSTRUCTIONS

This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local codes and ordinances.

DANGER

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a
qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not
modify the plug provided with the product – if it will not fit the outlet, have a proper outlet installed by a qualified
electrician.

This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in
Figure A. Make sure that the product is connected to an outlet having the same configuration as the plug.
No adapter should be used with this product.

Figure A

GROUNDED
OUTLET

GROUNDING PIN

GROUNDED
OUTLET BOX

4

Part names and functions

9876543

1

2

10 11 12 13 14

Main unit

Front

Legrest

1

Leg/Sole massage section

2

Includes air massage function

•

Sole Reflexology Plates

Removable

•
Position adjustment possible

•

Legrest Slide Lever

3

Extendable length to approx. 5 in.

•
(12 cm)

Control Panel

4

See page 7 to 8

Seat/Thigh Side Massage section

5

Seat/Thigh Soft Massage Plates
(integrated)

Position adjustment possible

•

Retracted position of massage

6

heads

Back Cushion

7

Pillow

8

Backrest

9

Includes integrated massage

•
heads

Seat

10

Includes integrated air massage

•
function

Armrest

11

Hand/Arm massage section

12

Includes integrated air massage

•
function

Control Panel Stand Covers

13

On both the left and right sides

•

Outer Shoulder massage section

14

Includes integrated air massage

•
function

Shoulder Plates

Removable

•
Position adjustment possible

•

5

18 1315 16 17

2322212019

Back

Back Cover

15

Control Panel Holder

16

Child Safety Decal

17

Control Panel Stand

18

Power Plug

19

Power Cord

20

Safety Precaution Label

21

Wheels

22

Power Supply Box

23

Lock Switch Power Switch

Lock Switch Key
Lock Switch Key Tag

For preventing children from

•
swallowing it by accident

6

Control Panel

13

14 161715

Cover closed

Off/On

1

Quick Stop

2

Press this button to stop the

•
massage immediately.

User Memory

3

See page 39 to 41

•

Program Selection

4

See page 18

•

Ottoman Angle Adjustment

5

See page 35

•

Reclining Angle Adjustment

6

See page 35

•

Display

7

This illustration simulates when all

•
lights are illuminated.
See page 8

•

Cover open

Voice Guidance Volume

8

See page 37

•

Ultra Knead

9

“Ultra Knead” is the name of the

•
massage actions.
See page 26 to 27

•

Repeat

10

See page 27

•

Massage Style Selection

11

See page 27

•

Position

12

See page 28

•

Back Intensity Adjustment

13

Adjustment of the massage heads

•
strength
See page 28

•

Stretch

14

See page 34

•

Air Massage Controls

15

Selection of the areas to be air

•
massaged
See page 30

•

Self-Program/Manual Operation

16

Controls

See page 22 to 23

•

Manual Adjustment Controls

17

See page 24 to 26

•

7

Display

* This illustration simulates when all lights are illuminated.

Voice Guidance Volume Display

1

See page 37

•

Off

Soft

Medium

Loud

Time Remaining Display

2

(During massage)

(After finishing massage)

Ultra Knead/Repeat Display

3

See page 27

•
(Ultra knead)

Pressure Display

5

Displays the pressure applied by

•
the massage heads

Massage Style Display

6

Displays the current massage

•
style

Thumb-like action

Palm-like action

Fist-like action

Self-Program Setting Display

7

See page 22 to 23

•

Manual Upper Body Massage

8

Display

See page 24 to 26

•

Air Intensity Display

9

See page 30

•

Stretch Display

10

Indicates whether the leg stretch

•
or the arm is on or off

On: Turned on

Massage Area Display

11

Flashes to indicate areas

•
currently being massaged
In the Massage Area Display,

•
positions are estimated.
Therefore, there may be some
differences between the actual
sensation and the display.

Back Intensity/Speed Display

12

Intensity and speed of the

•
massage heads are displayed.
The speed is displayed only in the

•
manual operation.

Manual Upper Body Complex

13

Operation Display

Indicates optional operations

•
added to manual upper body
operation
See page 25

•

TAP 1
TAP 2
REGIONAL ROLL
AUTO WIDTH

(Repeat)

User Memory Display

4

Illuminated when operating the

•
User Memory function
See page 39 to 41

•

Off: Turned off

In operation: flashing

8

Setting up the massage lounger

Where to use the unit

1

Ensure there is adequate space to recline.

Caution

Do not use the unit in areas with high humidity,

•
such as the bathroom, because this can lead to

electric shock or other accidents.

Place the unit on a totally flat surface.

•

Failure to do so may result in the unit tipping over.

Do not expose the massage lounger to direct sunlight or high

•
temperatures, such as in front of a heater, etc., as this can cause
discoloration or hardening of the synthetic leather.
Place the unit on a mat to prevent floor damage.

•
When placing a mat under the unit, the size of the mat should be

•
sufficient (at least 47 × 28 in. (120 × 70 cm)) to cover the areas
where the unit touches and where the legrest could touch the
floor, as shown in the diagram on the right.
Install the unit near a power outlet.

•

Removing everything from the box and installing the unit

2

Use care to prevent lower back and other injuries that could occur when lifting this heavy object (approx. 176 bs. (80 kg)).

•
(The unit must be carried by two persons.)
When using the wheels to move the unit, place a mat on the floor to protect the floor surface.

•

Keep at least 4" (10 cm) away from the wall.

Approx. 77" (195 cm)

Width approx. 33" (84 cm)

Approx. 12" (30 cm)

Approx. 14"
(35 cm)

Mat

Area where legrest
could touch the floor

Area where unit
touches the floor

To put the unit down on the floor

Put the unit down slowly and carefully watch your step.

•
Put down the legrest by holding it with your hands until it has been set on the floor completely. If you release your hands

•
before the legrest is fully extended, the legrest will forcefully return to the initial position.

Fabric Section

Groove

Hold the cloth
section on the
underside

Place your
fingers in the
groove

MatLegrest Back cover

9

Confirm that the main unit and the accessories are in the box.

Main unit

Width: Approx. 27" (68 cm)

Height: Approx. 26" (66 cm)

Length: Approx. 63" (160 cm)

Accessories

• Armrests (Right/Left)

Left/Right indication

Air plug

Small holes on the inside fabric are an intentional
part of the functional design.

• Allen Key — 1

(Cross-section)

0.2"
(4 mm)

• Pillow

This is installed on the sole
massage section prior to leaving
the factory.

• Control Panel Stand

Control panel
holder

• Control Panel Stand Covers

Fixing screw

Clip

• Shoulder Plates• Sole Reflexology Plates

• Attachment Screws (M6 × 16) — 7

Documents including the Operating Instructions

Operating Instructions

•
Child Safety Instructions (Yellow brochure)

•
How to transport and move (Yellow brochure)

•
Notes for body scanning (Pink brochure)

•
Quick Start Manual

•

• Lock Switch Keys — 2
One of the lock switch keys has been inserted
in the lock switch prior to leaving the factory.
The other lock switch key is a spare to be
stored for safekeeping out of the reach of
children.

Do not remove this tag.

10

Assembly

Attaching the

1

armrests

(On both the right and left
sides)

1. Insert the armrest into the
unit.

Be careful to avoid pinching

•

your fingers.

2. Fasten the armrest with the
attachment screws.

Set the two attachment
screws in place by hand
first and then tighten
firmly with the allen key.

Use this Screw

Attachment Screw (M6 ×

16)

(1) Align the

position

Attachment
Screw

Groove

Right/Left
indication

Armrest

Pipe

Turn screws

clockwise to

tighten.

(2) Fasten the armrest with

the attachment screws.

Main unit

Attachment

Screw

× 4

Make sure that the seat
surface is not damaged.

Connecting the air plugs

2

(On both the right and left sides)

Insert the air plugs into the unit.

Outside

Allen key

Inside

Push on the air
plugs until you hear
it click into place.

Air plug

11

Attaching the control panel stand to the right or left side panel of the unit

2

3

(Diagram shows attachment to right armrest.)

1. Insert the attachment screw into the lower hole first
and then tighten lightly by hand.

2. Securing the stand with the attachment screws.

Tighten the two screws for the remaining two holes
lightly by hand and then tighten firmly with the allen key.

Control panel stand

1 Insert the attachment

screw in either hole and
then tighten.

Attachment screw

Use this screw

Attachment Screw (M6 × 16)

× 3

Allen key

The position of the control panel when seated can be
selected by choosing the appropriate hole for the screw.

Near

To attach the control panel stand using the attachment
screws, tighten the screws level with the holes as
shown in the figure below.

If the screws are tightened at an angle, the hole may
become deformed and the screws may become stuck in
the middle.

Approx.
20˚

Far

Control panel stand

Control panel
stand

Attaching the control panel stand covers

4

(On both the right and left sides)

The method for attaching the covers is the same for both sides.
The diagram shows the side where the control panel stand is
attached.

1. Insert the top tabs on the cover into the bottom
notches on the armrest.

Notches

Hole

Tighten the screws
level with the holes.

2. Insert the bottom tabs into the notches on the
armrest.

Attachment screw

Hole

Allen key

Cover for Side WITH
Control Panel Stand

Bottom tabs

Allen key

Do not tighten the
screw at an angle
with the hole.

Cover for Side WITHOUT

Control Panel Stand

Attachment

screw

Top tabs

Control panel
stand cover

Notches

Push the cover until
you hear it click.

12

When removing the control panel stand cover

1. Insert the head of a flat-tip screwdriver in the gap
under the mark (O).

2. Push the bottom tab of the cover up to lift the cover.

3. Perform the same procedures as 1 and 2 above for
the other gap.

4. Pull the cover up diagonally.

Performing this procedure with the allen key or a

•
Phillips screwdriver could damage the unit.

Raising the backrest to the

5

upright position

1. Insert the power plug into the power outlet.

2. Confirm the key lock is set to the “open”
position.

3. Confirm the power switch is set to the “on”
position.

4. Press the
twice.

The backrest will rise to the upright position
automatically.

button on the control panel

Gap

2

1

2

Flat-tip
screwdriver
(Not included in
the standard
configuration)

13

Moving the control panel cord to the left side (when control panel stand is on left
side)

1. Press the button on the control panel to turn on the power.

Legrest

2. Press the
has risen far as it will go.

Continue pressing until a “beep-beep-beep” sound is heard.

3. Remove the control panel cord from the cord-holder groove.

4. Move the control panel cord under the legrest to the left side.

5. Fasten the control panel cord at two points in the cord-holder groove.

button on the control panel and hold until the legrest

Cord-Holder Groove

Control Panel Cord

Push in

Placing the control panel into the

6

control panel stand

1. Fit the groove on the side of the control panel to the
projection on the inside of the holder.

Control Panel Cord

Backside of the

control panel

Projection on the
inside of the holder

Groove on the control panel

14