Panasonic DMCFX30K User Manual

Operating Instructions

Digital Camera

Model No. DMC-FX30

PP

Before connecting, operating or

adjusting this product, please read

the instructions completely.

For USA assistance, please call: 1-800-272-7033 or send e-mail to : [e-mail]

For Canadian assistance, please call: 1-800-99-LUMIX (1-800-995-8649) or
send e-mail to: [e-mail]

P

PC

VQT1B86

Before Use

Before Use

Dear Customer,

Thank you for choosing Panasonic!

You have purchased one of the most
sophisticated and reliable products on the
market today. Used properly, we’re sure it
will bring you and your family years of
enjoyment. Please take time to fill in the
information on the below.
The serial number is on the tag located on
the underside of your Camera. Be sure to
retain this manual as your convenient
Camera information source.

Model No.

Serial No.

Information for Your Safety

WARNING:

TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR PRODUCT
DAMAGE,

• DO NOT EXPOSE THIS APPARATUS
TO RAIN, MOISTURE, DRIPPING OR
SPLASHING AND THAT NO
OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHALL BE
PLACED ON THE APPARATUS.

• USE ONLY THE RECOMMENDED
ACCESSORIES.

• DO NOT REMOVE THE COVER (OR
BACK); THERE ARE NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

Carefully observe copyright laws.
Recording of pre-recorded tapes or
discs or other published or broadcast
material for purposes other than your
own private use may infringe copyright
laws. Even for the purpose of private
use, recording of certain material may
be restricted.

2

VQT1B86

• Please note that the actual controls and
components, menu items, etc. of your
Digital Camera may look somewhat
different from those shown in the
illustrations in these Operating
Instructions.

• SDHC Logo is a trademark.

• Leica is a registered trademark of Leica
Microsystems IR GmbH.

• Elmarit is a registered trademark of Leica
Camera AG.

• Other names, company names, and
product names printed in these
instructions are trademarks or registered
trademarks of the companies concerned.

THE SOCKET OUTLET SHALL BE
INSTALLED NEAR THE EQUIPMENT
AND SHALL BE EASILY ACCESSIBLE.

CAUTION

Danger of explosion if battery is
incorrectly replaced. Replace only with
the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to
the manufacturer’s instructions.

Warning

Risk of fire, explosion and burns. Do not
disassemble, heat above 60 xC (140 oF)
or incinerate.

Marking sign is located on bottom of the
unit.

Before Use

THE FOLLOWING APPLIES ONLY IN
THE U.S.A.

FCC Note:

This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more
of the following measures:

• Reorient or relocate the receiving
antenna.

• Increase the separation between the
equipment and receiver.

• Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.

• Consult the dealer or an experienced
radio/TV technician for help.

FCC Caution: To assure continued

compliance, follow the
attached installation
instructions and use only
shielded interface cables
with ferrite core when
connecting to computer

or peripheral devices.
Any changes or modifications not
expressly approved by the party
responsible for compliance could void
the user’s authority to operate this
equipment.

3

VQT1B86

Before Use

Declaration of Conformity
Trade Name: Panasonic
Model No.: DMC-FX30
Responsible party:

Panasonic
Corporation of
North America
One Panasonic Way,
Secaucus, NJ 07094

Support Contact: Panasonic

Consumer
Electronics Company
1-800-272-7033

This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.

THE FOLLOWING APPLIES ONLY IN
CANADA

This Class B digital apparatus complies
with Canadian ICES-003.

-If you see this symbol-

Information on Disposal in other
Countries outside the European
Union

This symbol is only valid in the European
Union.
If you wish to discard this product, please
contact your local authorities or dealer
and ask for the correct method of
disposal.

∫ About the battery pack

CAUTION

Battery pack (Lithium ion battery pack)

• Use the specified unit to recharge the
battery pack.

• Do not use the battery pack with
equipment other than the specified
unit.

• Do not get dirt, sand, liquids, or other
foreign matter on the terminals.

• Do not touch the plug terminals
(i and j) with metal objects.

• Do not disassemble, remodel, heat or
throw into fire.

If any electrolyte should come into
contact with your hands or clothes,
wash it off thoroughly with water.
If any electrolyte should come into
contact with your eyes, never rub the
eyes. Rinse eyes thoroughly with water,
and then consult a doctor.

4

VQT1B86

∫ About the battery charger

CAUTION!
DO NOT INSTALL OR PLACE THIS
UNIT IN A BOOKCASE, BUILT-IN
CABINET OR IN ANOTHER
CONFINED SPACE. ENSURE THE
UNIT IS WELL VENTILATED. TO
PREVENT RISK OF ELECTRIC
SHOCK OR FIRE HAZARD DUE TO
OVERHEATING, ENSURE THAT
CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT
THE VENTILATION VENTS.

Battery charger

This battery charger operates on AC
between 110 V and 240 V.
But

• In the U.S.A. and Canada, the battery
charger must be connected to a 120 V
AC power supply only.

• When connecting to an AC supply
outside of the U.S.A. or Canada, use a
plug adaptor to suit the AC outlet
configuration.

∫ Care of the camera

• Do not strongly shake or bump the
camera.

This unit may malfunction, recording
pictures may no longer be possible or the
lens or the LCD monitor may be
damaged.

• We strongly recommend
you do not leave the
camera in your pants
pocket when you sit down
or forcefully insert it into a
full or tight bag etc.
Damage to the LCD
monitor or personal injury
may result.

• Be particularly careful in the following
places as they may cause this unit to
malfunction.

– Places with a lot of sand or dust.

Before Use

– Places where water can come into

contact with this unit such as when
using it on a rainy day or on a beach.

• If water or seawater splashes on the
camera, use a dry cloth to wipe the
camera body carefully.

∫ About Condensation (When the lens

is fogged up)

• Condensation occurs when the ambient
temperature or humidity changes. Be
careful of condensation since it causes
lens stains, fungus and camera
malfunction.

• If condensation occurs, turn the camera
off and leave it for about 2 hours. The fog
will disappear naturally when the
temperature of the camera becomes close
to the ambient temperature.

∫ Read together with the “Cautions for

Use”. (P95)

∫ About cards that can be used in this

unit

You can use an SD Memory Card, an
SDHC Memory Card and a
MultiMediaCard.

• When the term card is used in these
operating instructions this refers to the
following types of Memory Cards.
– SD Memory Card (8 MB to 2 GB)
– SDHC Memory Card (4 GB)
– MultiMediaCard

More specific information about memory
cards that can be used with this unit.

• You can only use an SDHC Memory Card
if using cards with 4 GB or more capacity.

• A 4 GB Memory Card without an SDHC
logo is not based on the SD Standard and
will not work in this product.

OK

44

• A MultiMediaCard is compatible with still
pictures only.

VQT1B86

5

Contents

Before Use

Information for Your Safety.......................2

Preparation

Standard Accessories............................... 8

Names of the Components....................... 8

Quick Guide..............................................9

Charging the Battery with the Charger .....10

About the Battery (charging/

number of recordable pictures) ...........11

Inserting and Removing the Card

(optional)/the Battery........................... 12

About the Built-in Memory/

the Card (optional) ..............................13

Setting Date/Time (Clock Set) ................ 14

• Changing the clock setting ...............15

About the Mode Dial ...............................15

Setting the Menu.....................................16

About the Setup Menu............................ 18

LCD Monitor Display/Switching

the LCD Monitor Display .....................21

Basic

Taking Pictures.......................................22

Taking Pictures in Simple Mode.............24

Taking Pictures with the Zoom ...............26

• Using the Optical Zoom/Using the

Extended Optical Zoom (EZ)............ 26

• Using the Digital Zoom

Further extending the zoom .............27

Checking the Recorded Picture

(Review).............................................. 28

Playing back/Deleting Pictures ...............29

Advanced (Recording pictures)

About the LCD Monitor ...........................31

•

Changing the information displayed

• Brightening the LCD Monitor

(Power LCD/High angle mode) ........33

6

VQT1B86

.... 31

Taking Pictures using the Built-in Flash

Taking Pictures with the Self-timer .........38

Compensating the Exposure ..................39

Taking Pictures using Auto Bracket........ 40

Changing the sensitivity according to

the movement of the subject

being recorded....................................41

Taking Close-up Pictures........................ 42

Taking pictures that match the scene

being recorded (Scene mode).............43

– [PORTRAIT].................................. 44

– [SOFT SKIN] ................................. 44

– [SELF PORTRAIT]........................44

– [SCENERY]................................... 45

– [SPORTS]...................................... 45

– [NIGHT PORTRAIT]...................... 45

– [NIGHT SCENERY].......................45

– [FOOD] ......................................... 46

– [PARTY] ........................................ 46

– [CANDLE LIGHT].......................... 46

– [BABY1]/[BABY2] .......................... 46

– [PET] .............................................47

– [SUNSET]...................................... 47

– [HIGH SENS.]................................ 48

– [STARRY SKY]..............................48

– [FIREWORKS]...............................49

– [BEACH]........................................49

– [SNOW] .........................................49

– [AERIAL PHOTO].......................... 49

– [UNDERWATER]........................... 50

Motion Picture Mode ............................... 51

Recording which Day of the Vacation

You Take the Picture...........................53

Displaying the Time at the Travel

Destination (World Time) ....................55

Using the [REC] Mode Menu ..................57

• [W.BALANCE]
Adjusting the hue for a more natural

picture............................................... 58

• [SENSITIVITY]

Setting the light sensitivity................60

• [ASPECT RATIO]
Setting the aspect ratio of pictures

• [PICT.SIZE]/[QUALITY]
Setting a picture size and quality
that match your use of the pictures

.....34

.... 60

.....61

• [AUDIO REC.]

Recording still pictures with audio .... 62

• [AF MODE]

Setting the focus method..................62

• [STABILIZER]
Detecting jitter and compensating

for it .................................................. 63

• [BURST]

Taking Pictures using Burst .............. 64

• [AF ASSIST LAMP]
Focusing in low light conditions

becomes easier................................65

• [SLOW SHUTTER]
Recording bright pictures in

dark places.......................................66

• [COL.MODE]
Setting a color effect and picture

quality for the recorded picture......... 66

Advanced (Playback)

Displaying Multiple Screens

(Multi Playback)...................................67

Displaying Pictures by Recording Date

(Calendar Playback)............................67

Using the Playback Zoom.......................68

Playing Back Motion Pictures/

Pictures with Audio..............................69

Creating still pictures from a

motion picture...................................... 70

Using the [PLAY] mode menu ................72

• [SLIDE SHOW]
Playing back pictures in order

for a fixed duration............................72

• [FAVORITE]

Setting your favorite pictures............74

• [ROTATE DISP.]/[ROTATE]

To display the picture rotated...........74

• [DATE STAMP]
Stamping information such as the

date on the recorded pictures........... 75

• [DPOF PRINT]
Setting the picture to print and the

number of prints ...............................77

• [PROTECT]
Preventing accidental erasure of

pictures.............................................79

• [AUDIO DUB.]

Adding audio after taking pictures ....80

• [RESIZE]

Making the picture smaller................80

• [TRIMMING]
Enlarging a picture and trimming it

• [ASPECT CONV.]
Changing the aspect ratio of

a 16:9 picture....................................82

• [COPY]

Copying the picture data...................83

• [FORMAT]
Initializing the built-in memory or

a card................................................ 84

......81

Connecting to other equipment

Connecting to a PC.................................85

Printing the Pictures................................88

Playing Back Pictures on a TV Screen

......92

Others

Screen Display........................................93

Cautions for Use.....................................95

Message Display ....................................97

Troubleshooting ......................................99

Number of Recordable Pictures and

Available Recording Time .................104

Specifications........................................107

Digital Camera Accessory System........110

Digital Camera Accessory Order Form

(For USA Customers)........................111

Request for Service Notice

(For USA Only)..................................112

Limited Warranty (For USA Only) .........113

Customer Services Directory

(For USA Only)..................................115

Précautions à prendre

(pour le Canada) ...............................116

Index .....................................................118

VQT1B86

7

Preparation

Preparation

Standard Accessories

Check that all the accessories are included
before using the camera.

12

DMW-BCE10PP

3

K1HA08CD0013

56

7

DE-A39B

4

K1HA08CD0014

VFC4090

1 Battery Pack

(Indicated as battery in the text)

2 Battery Charger

(Indicated as charger in the text)

3 USB Connection Cable
4 AV Cabl e
5 CD-ROM
6 Strap
7 Battery Carrying Case

• SD Memory Card, SDHC Memory Card

and MultiMediaCard are indicated as card
in the text.

• The card is optional.
You can record or play back pictures
on the built-in memory when you are
not using a card. (P13)

• For information about optional
accessories, refer to the “Digital Camera
Accessory System”. (P110)

• If any accessories are lost, customers in
the USA should contact Panasonic’s parts
department at 1 800 833-9626 and
customers in Canada should contact
1 800 99-LUMIX (1-800-995-8649) for
further information about obtaining
replacement parts.

Names of the Components

8

VQT1B86

VYQ3914

123

1 Flash (P34)
2 Lens (P5, 96)
3 Self-timer indicator (P38)

AF assist lamp (P65)

54

8 96 7

4 LCD monitor (P21, 31, 93)
5 Cursor buttons

2/Self-timer button (P38)
4/[REV] button (P28)
1/Flash setting button (P34)
3/Exposure compensation (P39)/

Auto bracket (P40)/
White balance fine adjustment (P59)/
Backlight compensation in simple mode
(P25) button

In these operating instructions,
operations using the cursor button are
described with illustrations below.
e.g.: When you press the 4 button

6 Status indicator (P19, 21)
7 [MENU/SET] button (P14)
8 [DISPLAY/LCD MODE] button

(P31, 33)

9 [FUNC] (P57)/Delete (P29) button

Preparation

13 Microphone (P51, 62, 80)
14 Shutter button (P22, 51)
15 Mode dial (P15)

16
17

18
19

16 Strap eyelet
17 Lens barrel
18 [AV OUT/DIGITAL] socket (P85, 88, 92)
19 [DC IN] socket (P85, 88)

• Always use a genuine Panasonic AC
adaptor (DMW-AC5PP; optional).

• This camera cannot charge the battery
even though the AC adaptor
(DMW-AC5PP; optional) is connected
to it.

20 21

22

20 Tripod receptacle

• When you use a tripod, make sure the
tripod is stable when the camera is
attached to it.

21 Card/Battery door (P12)
22 Release lever (P12)

101211

13 14 15

10 Camera ON/OFF switch (P14)
11 Zoom lever (P26)
12 Speaker (P69)

9

VQT1B86

Preparation

Quick Guide

This is an overview of how to record and
play back pictures with the camera. For
each step, be sure to refer to the pages
indicated in brackets.

1 Charge the battery. (P10)

• The battery is not charged when the
camera is shipped. Charge the
battery before use.

2

Insert the battery and the card. (P12)

1 Set the mode dial to [ ].
2 Press the shutter button to take

pictures. (P22)

4 Play back the pictures.

1 Set the mode dial to [ ].
2 Select the picture you want to view.

(P29)

Charging the Battery with the Charger

The battery is not charged when the
camera is shipped. Charge the battery
before use.

1 Attach the battery with attention

to the direction of the battery.

• When you do not use the card, you
can record or play back pictures on
the built-in memory. (P13) Refer to
P13 when you use a card.

3

Turn the camera on to take pictures.

• Set the clock. (P14)

OFF

ON

10

VQT1B86

2 Connect the charger to the

electrical outlet.

• Charging starts when the [CHARGE]
indicator A lights green.

• Charging is complete when the
[CHARGE] indicator A turns off (after
about 120 minutes).

• When the [CHARGE] indicator flashes,
read P12.

3 Detach the battery after charging

is completed.

• After charging is completed, be sure to
disconnect the charger from the electrical
outlet.

• The battery becomes warm after using it
and during and after charging. The
camera also becomes warm during use.
This is not a malfunction.

• The battery will be exhausted if left for a
long period of time after being charged.
Recharge the battery when it is exhausted.

• The battery can be charged even if it is
not fully discharged.

• Use the dedicated charger and battery.

• Charge the battery with the charger
indoors.

• Do not disassemble or modify the
charger.

Preparation

About the Battery

(charging/number of recordable
pictures)

∫ The battery life
The number of recordable pictures
(By CIPA standard in normal picture
mode [ ])

Number of
recordable pictures

Recording conditions by CIPA standard

• Temperature: 23 °C (73.4 °F)/
Humidity: 50% when LCD monitor is on.

• Using a Panasonic SD Memory Card
(16 MB).

• Using the supplied battery.

• Starting recording 30 seconds after the
camera is turned on. (When the optical
image stabilizer function is set to [MODE1].)

• Recording once every 30 seconds with
full flash every second recording.

• Rotating the zoom lever from Tele to Wide
or vice versa in every recording.

• Turning the camera off every
10 recordings and leaving it until the
temperature of the battery decreases.

¢ The number of recordable pictures

decreases when the power LCD
function or high angle mode (P33) are
used.

• CIPA is an abbreviation of
[Camera & Imaging Products
Association].

The number of recordable pictures
varies depending on the recording
interval time.
If the recording interval time becomes
longer, the number of recordable
pictures decreases.
[e.g. When recording once every
2 minutes, the number of recordable
pictures decreases to about 70.]

Approx. 280 pictures
(Approx. 140 min)

¢

11

VQT1B86

Preparation

Playback time

Playback time Approx. 300 min

The number of recordable pictures and
playback time will vary depending on the
operating conditions and storing condition
of the battery.

∫ Charging

Charging time Approx. 120 min

Charging time and number of recordable
pictures with the optional battery pack
(DMW-BCE10PP) are the same as above.

• The [CHARGE] indicator lights when
charging starts.

∫ When the [CHARGE] indicator flashes

• When the battery temperature is
excessively high or low, [CHARGE]
indicator flashes and the charging time
will be longer than normal.

• The terminals of the charger or the battery
are dirty. In this case, wipe them with a dry
cloth.

• When the operating time of the camera
becomes extremely short even after
properly charging the battery, the life of
the battery may have expired. Buy a new
battery.

∫ Charging conditions

• Charge the battery in a temperature
between 10 oC to 35 oC (50 oF to 95 oF).
(The battery temperature should also be
the same.)

• The performance of the battery may
temporarily deteriorate and the operating
time may become shorter in low
temperature conditions (e.g. skiing/
snowboarding).

Inserting and
Removing the Card
(optional)/the Battery

• Check that this unit is turned off.

• Prepare a card. (optional)

• You can record or play back pictures
on the built-in memory when you are
not using a card. (P13)

1 Slide the release lever in the

direction of the arrow and open
the card/battery door.

• Always use genuine Panasonic
batteries (DMW-BCE10PP).

• If you use other batteries, we cannot
guarantee the quality of this product.

2 Battery:

Insert it fully being careful about
the direction you insert it.
Pull the lever A in the direction of
the arrow to remove the battery.
Card:
Push it fully until it clicks being
careful about the direction you
insert it.
To remove the card, push the card
until it clicks, then pull the card
out upright.

A

12

VQT1B86

B

B: Do not touch the connection

terminals of the card.

• The card may be damaged if it is not
fully inserted.

3 1 Close the card/battery door.

2 Slide the release lever in the

direction of the arrow.

• If the card/battery door cannot be
completely closed, remove the card,
check its direction and then insert it
again.

• Remove the battery after use. Store the
removed battery in the battery carrying
case (supplied).

• Do not remove the battery until the
LCD monitor and the status indicator
(green) turn off as the settings on the
camera may not be stored properly.

• The supplied battery is designed only
for the camera. Do not use it with any
other equipment.

• Do not insert or remove the battery or
the card while this unit is turned on.
The data on the built-in memory or the
card may be damaged. Be particularly
careful while the built-in memory or the
card is being accessed. (P21)

• We recommend using a Panasonic
card.

Preparation

About the Built-in Memory/the Card (optional)

The built-in memory can be used as a
temporary storage device when the card
being used becomes full.

∫ Built-in Memory [ ]

• You can record or play back pictures
with the built-in memory. (The built-in
memory cannot be used when a card is
inserted.)

• The built-in memory capacity is about
27 MB.

• Picture size is fixed to QVGA
(320k240 pixels) when recording
motion pictures to the built-in memory.
(P51)

∫ Card [ ]
You can record or play back pictures on
a card.

∫ Card (optional)

• The SD Memory Card, SDHC Memory
Card and MultiMediaCard are small,
lightweight, removable external cards.

• The SDHC Memory Card is a memory
card standard decided by the SD
Association in 2006 for high capacity
memory cards more than 2 GB.

• The reading/writing speed of an SD
Memory Card and an SDHC Memory
Card is fast. Both types of card are
equipped with a Write-Protect switch A
that prevents writing and formatting the
card. (If the switch is slid to the [LOCK]
side, it is not possible to write or delete
data on the card and format it. When the
switch is slid to the other side, these
functions become available.)

2

13

VQT1B86

Preparation

• This unit (SDHC compatible equipment) is
compatible with SD Memory Cards based
on SD Memory Card Specifications and
formatted in FAT12 system and FAT16
system. It is also compatible with SDHC
Memory Cards based on SD Memory
Card Specifications and formatted in
FAT32 system.

• You can use an SDHC Memory Card in
equipment that is compatible with SDHC
Memory Cards however you cannot use
an SDHC Memory Card in equipment that
is only compatible with SD Memory Cards.
(Always read the operating instructions for
the equipment being used. If you also
order a photo studio to print pictures, ask
the photo studio before printing.)

Please confirm the latest information on the
following website.

http://panasonic.

co.jp/pavc/global/cs

(This Site is English only.)

• Refer to P104 for information about the
number of recordable pictures and the
available recording time for each Card.

• We recommend using High Speed SD
Memory Cards/SDHC Memory Cards
when recording motion pictures. (P51)

• The data on the built-in memory or the
card may be damaged or lost due to
electromagnetic waves, static electricity or
breakdown of the camera or the card. We
recommend storing important data on a
PC etc.

• Do not format the card on your PC or
other equipment. Format it on the camera
only to ensure proper operation. (P84)

• Keep the Memory Card out of reach of
children to prevent swallowing.

Setting Date/Time (Clock Set)

∫ Initial setting

The clock is not set so the following screen
appears when you turn the camera on.

OFF

A: [MENU/SET] button
B: Cursor buttons
C: Mode dial

1 Press [MENU/SET].
2 Press 3/4/2/1 to select the

date and time.

A: Time at the home area
B: Time at the travel destination (P55)

• 2/1: Select the desired item

• 3/4: Set the display order for the date
and time.

• : Cancel without setting the clock.

ON

PLEASE SET THE CLOCK

CLOCK SET

MENU

:
:

CLOCK SET

JAN

11 2007

00 00

:

..

M/D/Y

SELECT SET

CANCEL

EXIT

MENU

.

14

VQT1B86

3 Press [MENU/SET] to set.

• Turn the camera off after setting the clock.
Then set the mode dial to a recording
mode to turn the camera on and check
whether or not the clock setting is correct.

∫ Changing the clock setting
1 Press [MENU/SET].
2 Press 3/4 to select [CLOCK SET].

(P57)

3 Press 1 and then perform steps

2 and

3 to set the clock.

4 Press [MENU/SET] to close the menu.

• You can also set the clock in the
[SETUP] menu. (P18)

Preparation

About the Mode Dial

If you turn on this unit and then rotate
the mode dial, you can not only switch
between recording and playback but
also switch to macro mode to take a
close-up picture of a subject or to a
scene mode that matches your
recording purpose.

∫ Selecting the mode
Align a desired mode with the part A.

Rotate the mode dial slowly and surely to
adjust to each mode. (Do not adjust it to
parts where there is no mode.)

• When a fully charged battery has been
inserted for more than 24 hours, the clock
setting is stored (in the camera) for at
least 3 months even if the battery is
removed. (If you insert a battery that is not
sufficiently charged, the length of time that
the clock setting is stored may become
less.) However, the clock setting is
canceled after this length of time. In this
case, set the clock again.

• You can set the year from 2000 to 2099.
The 24-hour system is used.

• If the clock is not set, the correct date
cannot be printed when you stamp the
date on the pictures with [DATE STAMP]
(P75) or order a photo studio to print the
pictures. (P78)

SCN

N

SC

NORMAL PICTURE

• The above screen B appears on the LCD
monitor if the mode dial is rotated. (P20)
The mode currently selected appears on
the LCD monitor when the camera is
turned on.

15

VQT1B86

Preparation

∫ Basic

: Normal picture mode (P22)

Use this mode for normal recording.

: Simple mode (P24)

This mode is recommended for beginners.

: Playback mode (P29)

This mode allows you to play back
recorded pictures.

∫ Advanced

: Intelligent ISO sensitivity mode

(P41)

This mode automatically sets the optimal
ISO sensitivity and shutter speed according
to the movement and the brightness of the
subject.

: Macro mode (P42)

This allows you to take close-up pictures of
a subject.

: Scene mode (P43)

This allows you to take pictures that match
the scene being recorded.

: Motion picture mode (P51)

This mode allows you to record motion
pictures.

: Print mode (P88)

Use this to print pictures.

Setting the Menu

∫ Displaying the menu screens

Press [MENU/SET].

e.g.: The first page of the total 3 pages is

displayed.

1

EXIT

AWB
AUTO

/

3

MENU

REC

W.BALANCE

SENSITIVITY
ASPECT RATIO
PICT.SIZE

QUALITY

SELECT

A Menu icons
B Current page
C Menu items and settings

• Rotate the zoom lever while selecting the
menu item to switch to the next/previous
page easily.

• The menu icons and the menu items that
are displayed differ depending on the
position of the mode dial.

∫ About the menu icons

[REC] mode menu (P57):

This is displayed when the mode dial is set
to [ ]/[ ]/[ ]/[ ]/[ ].

[PLAY] mode menu (P72):

This is displayed when the mode dial is set
to [ ].

16

VQT1B86

[SCENE MODE] menu (P43):

This is displayed when the mode dial is set
to [ ].

[SETUP] menu (P18):

This is displayed when the mode dial is set
to [ ]/[ ]/[ ]/[ ]/[ ]/[ ].

∫ Setting menu items

• The following example shows how to set
[AUDIO REC.] when normal picture mode
[ ] is selected.

1 Press 3/4 to select the menu

item.

1

EXIT

EXIT

/

3

AWB

AUTO

MENU

2

/

3

OFF

MODE1

OFF

ON

MENU

REC

W.BALANCE
SENSITIVITY
ASPECT RATIO
PICT.SIZE
QUALITY

SELECT

REC

AUDIO REC.

SENSITIVITY
AF MODE

STABILIZER
BURST
AF ASSIST LAMP

SELECT

•Press 4 at A to switch to the next
screen.

2 Press 1.

2

SET

/

3

OFF

ON

MODE1

OFF

ON

MENU

REC

AUDIO REC.
AF MODE

STABILIZER
BURST
AF ASSIST LAMP

SELECT

3 Press 3/4 to select the setting.

2

SET

/

3

OFF

ON

MODE1

OFF

ON

MENU

REC

AUDIO REC.
AF MODE

STABILIZER
BURST
AF ASSIST LAMP

SELECT

Preparation

∫ Closing the menu screen

Press [MENU/SET].

• When the mode dial is set to [ ]/
[ ]/[ ]/[ ]/[ ], you can also
close the menu screen by pressing the
shutter button halfway.

∫ Switching to the [SETUP] menu

1 Press 2 on a menu screen.

1

EXIT

AWB

AUTO

/

3

MENU

REC

W.BALANCE

SENSITIVITY
ASPECT RATIO
PICT.SIZE

QUALITY

SELECT

2 Press 4 to select the [SETUP]

menu icon.

1

EXIT

/

n

OFF

4

0

MENU

SETUP

SELECT

CLOCK SET
WORLD TIME
MONITOR
GUIDE LINE

TRAVEL DATE

3 Press 1.

1

EXIT

/

n

OFF

4

0

MENU

SETUP

CLOCK SET
WORLD TIME
MONITOR
GUIDE LINE

TRAVEL DATE

SELECT

• Select a menu item next and set it.

4 Press [MENU/SET] to set.

2

EXIT

/

3

ON

MODE1

OFF

ON

MENU

REC

AUDIO REC.
AF MODE

STABILIZER
BURST
AF ASSIST LAMP

SELECT

MENU

/SET

17

VQT1B86

Preparation

About the Setup Menu

• Set items as required. (Refer to P18 to 20
for each menu item.)

• Select [RESET] to return the settings to the
initial settings at the time of purchase. (P20)

• [CLOCK SET], [AUTO REVIEW],
[POWER SAVE] and [ECONOMY] are
important items. Check their settings
before using them.

[CLOCK SET]

(Changing the date and time.)

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Change date and time. (P14)

[AUTO REVIEW]

(Displaying the recorded picture.)

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Set the length of time that the picture is
displayed after taking it.

[OFF]
[1SEC.]
[3SEC.]
[ZOOM]: The picture is displayed for

• The auto review function is not activated

• When pictures are recorded in auto bracket

• The auto review function is activated while

• The auto review setting is disabled when

1 second and then enlarged 4k
and displayed for 1 more second.

in motion picture mode [ ].

(P40) or burst mode (P64), the auto review
function is activated regardless of the
setting on the auto review function. (The
picture is not enlarged.)

pictures with audio (P62) are being
recorded regardless of its setting. (The
picture is not enlarged.)

using auto bracket or burst mode, in
motion picture mode [ ] or when
[AUDIO REC.] or [SELF PORTRAIT] in
scene mode is set to [ON].

[POWER SAVE]

(Turning off this unit automatically.)

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Power save mode is activated (the camera
is automatically turned off to save the
battery life) if the camera has not been
used for the time selected on the setting.

[1MIN.], [2MIN.], [5MIN.], [10MIN.], [OFF]

• Press the shutter button halfway or turn
this unit off and on to cancel power save
mode.

• Power save mode is fixed to [2MIN.] when
economy mode is activated and [5MIN.] in
simple mode [ ].

• Power save mode is not activated in the
following cases.
– When using the AC adaptor

(DMW-AC5PP; optional)
– When connecting to a PC or a printer
– When recording or playing back motion

pictures
– During a slide show (P72)

[ECONOMY]
(Turning off the LCD monitor
automatically.)

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
The brightness of the LCD monitor is
reduced, and the LCD monitor is turned off
automatically while the camera is not in
use, to save battery life when recording.
[LEVEL 1]: The LCD monitor turns off if the

camera is not operated for
about 15 seconds in recording
mode.

[LEVEL 2]: The LCD monitor turns off if the

camera is not operated for
about 15 seconds in recording
mode or for about 5 seconds
after taking a picture.

[OFF]: Economy mode cannot be

activated.

• The LCD monitor is turned off while the

flash is being charged.

18

VQT1B86

• The status indicator lights while the LCD
monitor is turned off. Press any button to
turn on the LCD monitor again.

• Power save mode is fixed to [2MIN.].
[However, power save mode is not
activated when using the AC adaptor
(DMW-AC5PP; optional).]

• The brightness of the LCD monitor is not
reduced in Power LCD mode and high
angle mode.

• Economy mode is not activated in the
following cases.
– In simple mode [ ]
– When using the AC adaptor

(DMW-AC5PP; optional)
– While a menu screen is displayed
– While the self-timer is set
– While recording motion pictures

[WORLD TIME] (P55)

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Set the time in your home area and travel
destination.

[]:Your home area
[]:Travel destination area

[MONITOR]

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Adjust the brightness of the LCD monitor in
7 steps.

[GUIDE LINE]

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Set the pattern of the guide lines displayed
when taking pictures. (P31, 32)
You can also set whether or not to have the
recording information and histogram
displayed when the guide lines are
displayed.

[REC. INFO.]: [ON]/[OFF]
[HISTOGRAM]:[ON]/[OFF]
[PATTERN]: [ ]/[ ]

Preparation

[TRAVEL DATE] (P53)

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Set the departure date and the return date
of the vacation.

[SET], [OFF]

[BEEP]

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
This allows you to set the beep.

[BEEP LEVEL]
[]:No operation sound
[]:Soft operation sound
[]:Loud operation sound
[BEEP TONE]: / /

1 2 3

[SHUTTER]

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
This allows you to set the shutter sound.

[SHUTTER VOL.]
[]:No shutter sound
[]:Soft shutter sound
[]:Loud shutter sound
[SHUTTER TONE]: / /

[VOLUME]

MENU

Press [ ] to display the [SETUP] menu

/SET

1 2 3

and select the item to set. (P16)
The volume of speakers can be adjusted in
7 steps from level 6 to 0.

• When you connect the camera to a TV, the
volume of the TV speakers does not change.

[NO.RESET]

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Reset the file number of the next recording
to 0001.

• The folder number is updated and the file
number starts from 0001. (P86)

• A folder number between 100 and 999
can be assigned.
When the folder number reaches 999, the
number cannot be reset. We recommend
formatting the card after saving the data
on a PC or elsewhere.

19

VQT1B86

Preparation

• To reset the folder number to 100, format
(P84) the built-in memory or the card first
and then use this function to reset the file
number.
A reset screen for the folder number will
then appear. Select [YES] to reset the
folder number.

[RESET]

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
The [REC] or [SETUP] menu settings are
reset to the initial settings.

• [FAVORITE] (P74) is fixed to [OFF] and
[ROTATE DISP.] (P74) is fixed to [ON].

• If the [SETUP] menu settings are reset,
the following settings are also reset.
– The birthday settings for [BABY1]/

[BABY2] (P46) and [PET] (P47) in scene
mode.

– The number of days that have passed

since the departure date in
[TRAVEL DATE]. (P53)

– The [WORLD TIME] (P55) setting.

• The folder number and the clock setting
are not changed.

[VIDEO OUT]

(Playback mode only) (P92)

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Set to match the color television system in
each country.
[NTSC]: Video output is set to NTSC

system.

[PAL]: Video output is set to PAL

system.

[TV ASPECT]

(Playback mode only)

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Set to match the type of TV.

[ ]:

When connecting to a 16:9 screen TV.

[]:

When connecting to a 4:3 screen TV.

[SCENE MENU]

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Set the screen that will appear when the
mode dial is set to [ ].
[AUTO]: The [SCENE MODE] menu

screen appears.

[OFF]: The recording screen in the

currently selected scene mode
appears.

[DIAL DISPLAY]

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Set whether or not to show the mode dial
display when the mode dial is rotated.

[ON], [OFF]

[LANGUAGE]

MENU

Press [ ] to display the [SETUP] menu

/SET

and select the item to set. (P16)
Set the language displayed on the screen.

[ENGLISH], [DEUTSCH], [FRANÇAIS],
[ESPAÑOL], [ITALIANO], [ ]

¢

,

[]

¢ Not displayed on DMC-FX30P

• If you set a different language by mistake,
select [ ] from the menu icons to set the
desired language.

20

VQT1B86

LCD Monitor Display/ Switching the LCD Monitor Display

∫ Screen display in normal picture

mode [ ] (at the time of purchase)

3756 712

4

13

1 Recording mode
2 Flash mode (P34)

• If you press the shutter button halfway
when the flash is activated, the flash
icon turns red.

3 AF area (P22)

• The AF area displayed is bigger than
usual when taking pictures in dark
places.

4 Focus (P22)
5 Picture size (P61)
6 Quality (P61)

: Jitter alert (P24)

7 Battery indication

• The indication turns red and blinks if
the remaining battery power is
exhausted. (The status indicator blinks
when the LCD monitor turns off.)
Recharge the battery or replace it with
a fully charged battery.

• It does not appear when you use the
camera with the AC adaptor
(DMW-AC5PP; optional) connected.

8 Number of recordable pictures (P104)
9 Recording state

8

9

10

1/30F2.8

1112

Preparation

10 Built-in memory/Card

• The access indication lights red when
pictures are being recorded on the
built-in memory (or the card).
– When using the built-in memory

– When using the card

• Do not do the following when the
access indication lamps lights. The
card or the data on the card may be
damaged and this unit may no
longer operate normally.
– Turn this unit off.
– Remove the battery or the card.

(when using a card)
– Shake or bump this unit.
– Disconnect the AC adaptor.

(DMW-AC5PP; optional) (when

using the AC adaptor)

• Do not do the above when pictures are
being read or deleted or the built-in
memory (or the card) is being
formatted (P84).

• The access time for the built-in
memory may be longer than the
access time for a card.

11 Shutter speed (P22)
12 Aperture value (P22)

• If the exposure is not adequate, the
aperture value and the shutter speed
turn red. (They do not turn red when
the flash is activated.)

13 Optical Image Stabilizer (P63)

• Refer to P93 for information about other
screen displays.

∫ Switching the screen display

You can change the screen display by
pressing [DISPLAY]. This allows you to
display information while taking pictures
such as the picture size or the number of
recordable pictures or take pictures without
displaying any information. Refer to P31 for
details.

21

VQT1B86

Basic

Basic

Taking Pictures

The camera automatically sets the shutter
speed and the aperture value according to
the brightness of the subject.

1: Shutter button

• The status indicator 3 lights for about
1 second when you turn this unit on 2.

1 Hold this unit gently with both

hands, keep your arms still at
your side and stand with your feet
slightly apart.

A:Flash
B: AF assist lamp
C: When holding the camera vertically

2 Aim the AF area at the point you

want to focus on.

3 Press the shutter button halfway

to focus.

1/25F2.8

•

The focus indication 2 lights green and
the AF area

3: Aperture value
4: Shutter speed

• The focus range is 50 cm (1.64 feet)
to ¶.

• The subject is not focused in the
following cases.
– The focus indication blinks (green).
– The AF area turns white to red or

there is no AF area.

– The focus sound beeps 4 times.

• If the distance is beyond the focus
range, the picture may not be properly
focused even if the focus indication
lights.

1

turns from white to green.

4 Press the halfway pressed

shutter button fully to take a
picture.

∫ Using the flash

If the camera determines that the place
where the picture is being taken is dark, the
flash is activated when the shutter button is
pressed fully. (When the flash is set to
AUTO [ ]/AUTO/Red-eye reduction
[].)

• You can switch the flash setting to match
the recording. (P34)

22

VQT1B86

• When you press the shutter button, the
LCD monitor may become bright or dark
for a moment however the recorded
picture will not be affected.

• Be careful not to move the camera when
you press the shutter button.

• Do not cover the flash or the AF assist
lamp with your fingers or other objects.

• Do not touch the front of the lens.

∫ Exposure (P39)

• If you select normal picture mode [ ] the
exposure is automatically adjusted to an
appropriate exposure (AE=Auto
Exposure). However, depending on
recording conditions such as the
backlight, the picture will become dark.

In this case, compensate the exposure.
This allows you to take bright pictures.

∫ Focusing (P23, 42)

If you select normal picture mode [ ], the
picture is automatically focused (AF= Auto
Focus). However, one of the subjects in the
picture may not be properly focused. The
focus range is 50 cm (1.64 feet) to ¶.

– When there are both near and distant

subjects in a scene.

– When there is dirt or dust on glass

between the lens and the subject.

– When there are illuminated or glittering

objects around the subject.
– When taking a picture in dark places.
– When the subject is moving fast.
– When the scene has low contrast.
– When recording a very bright subject.
– When taking close-up pictures of a

subject.
– When jitter occurs.

Try the AF/AE lock technique or macro
mode.

Basic

∫ Color (P58)

• The color of the subject will differ if the
color of the light surrounding it differs such
as when the light comes from sunlight or
halogen lighting. However, this unit
automatically adjusts the hue to one close
to real life. (auto white balance)

Set the white balance if you want to
change the hue you get with auto white
balance.

∫ When you want to take a picture of a

subject outside the AF area (AF/AE
Lock)

When recording a picture of people with a
composition like the following picture, you
will not be able to focus the camera on the
subject because the people are outside the
AF area.

7

In this case,

1 Aim the AF area at the subject.
2 Press the shutter button halfway to fix

the focus and the exposure.

• The focus indication lights when the
subject is focused.

3 Press and hold the shutter button

halfway while moving the camera as you

compose the picture.

4 Press the shutter button fully.

• You can repeatedly retry AF/AE lock
before pressing the shutter button fully.

1/125F4.5

1/125F4.5

23

VQT1B86

Basic

∫ Direction detection function

Pictures recorded with the camera held
vertically are played back vertically
(rotated). (Only when [ROTATE DISP.]
(P74) is set to [ON])

• Pictures may not be displayed vertically if
they were taken with the camera aimed up
or down.

• Motion pictures taken with the camera
held vertically are not displayed vertically.

∫ Preventing jitter (camera shake)

• Be careful of jittering when pressing the
shutter button.

• If jitter could occur because of slow
shutter speed, the jitter alert A appears.

Taking Pictures in Simple Mode

This mode allows beginners to take
pictures easily. Only the basic functions
appear in the menu to make operations
simple.

∫ Basic menu settings

1 Press [MENU/SET].
2 Press 3/4 to select the desired

menu item and then press 1.

1/10F2.8

• When the jitter alert appears, we
recommend using a tripod. If you cannot
use a tripod, be careful how you hold the
camera (P22). The use of the self-timer
prevents jittering caused by pressing the
shutter button when you are using a tripod
(P38).

• Shutter speed will be slower particularly in
the following cases. Keep the camera still
from the moment the shutter button is
pressed until the picture appears on the
screen. We recommend using a tripod.
– Slow sync./Red-eye reduction (P34)
– [NIGHT PORTRAIT] (P45)
– [NIGHT SCENERY] (P45)
– [PARTY] (P46)
– [CANDLE LIGHT] (P46)
– [STARRY SKY] (P48)
– [FIREWORKS] (P49)
– When the shutter speed is slowed in

[SLOW SHUTTER] (P66)

24

VQT1B86

SIMPLE MODE

PICT.MODE
AUTO REVIEW
BEEP
CLOCK SET

SELECT SET

ENLARGE

"

4

k

6"/10k15cm

E-MAIL

MENU

3 Press 3/4 to select the desired

setting and then press [MENU/
SET].

4 Press [MENU/SET] to close the

menu.

• You can also press the shutter
button halfway to close the menu.

∫ Settings in Simple mode

[PICT.MODE]

[ENLARGE]

[4qk6q/

10k15cm]

[E-MAIL]

Suitable for enlarging the
pictures to be printed to
8

qk10q

size, letter size etc.

Suitable for regular size
printing.

Suitable for attaching
pictures to e-mails or
adding pictures to websites.

[AUTO REVIEW]

[OFF] The recorded picture does not

automatically appear.

[ON] The recorded picture

automatically appears on the
screen for about 1 second.

[BEEP]

[OFF] No operation sound
[LOW] Soft operation sound
[HIGH] Loud operation sound

[CLOCK SET]

Change date and time. (P14)

[ 4qk6q/10k15cm]

•If

or [ E-MAIL] is
set in [PICT.MODE], the extended optical
zoom is activated. (P26)

• The settings for [BEEP] and
[CLOCK SET] in simple mode are also
applied to other recording modes.

• The settings for [WORLD TIME] (P19),
[MONITOR] (P19), [TRAVEL DATE] (P19),
[BEEP] (P19), [SHUTTER] (P19),
[NO.RESET] (P19) and [LANGUAGE]
(P20) in the [SETUP] menu are applied to
simple mode.

∫ Other Settings in Simple mode

In simple mode, other settings are fixed as
follows. For more information about each
setting, refer to the page indicated.

• Focus range:
30 cm (0.98 feet) to ¶ (Tele)
5 cm (0.16 feet) to ¶ (Wide)

• [POWER SAVE] (P18):
[5MIN.]

• [ECONOMY] (P18):
[OFF]

• Self-timer (P38):
10 seconds

• Optical Image Stabilizer (P63):
[MODE2]

• [W.BALANCE] (P58):
[AWB]

Basic

• [SENSITIVITY] (P60):
This setting becomes the same as when
the highest ISO sensitivity is set to
[ISO800] in Intelligent ISO sensitivity
mode [ ]. (P41)

• [ASPECT RATIO]/[PICT.SIZE]/[QUALITY]
(P60, 61):

– [ ENLARGE]:

: (7M)/

–[ 4qk6q/10k15cm]:

: (2.5M EZ)/

– [ E-MAIL]:

: (0.3M EZ)/

• [AF MODE] (P62):
[]

• [AF ASSIST LAMP] (P65):
[ON]

• You cannot use the following functions.
– High angle mode
– White balance fine adjustment

– Exposure compensation
– Auto bracket
–[AUDIOREC.]
– [D.ZOOM]
– [BURST]
– [SLOW SHUTTER]
– [COL.MODE]
– [GUIDE LINE]

• You cannot set the following items in
simple mode.
– [TRAVEL DATE]
–[WORLDTIME]

∫ The Backlight Compensation

Backlight refers to when light comes from
the back of a subject.
In this case, the subject, such as a person,
will become dark so this function
compensates the backlight by brightening
the whole of the picture.

25

VQT1B86

Basic

Press 3.

• When the backlight compensation
function is activated, [ ]
(compensating backlight ON indication
A) appears. Press 3 again to cancel
this function.

∫ To make subjects appear further away

use (Wide)

Rotate the zoom lever towards
Wide.

T

W

7 7

BACKLIGHT BACKLIGHT

• We recommend using the flash when you
use the backlight compensation function.
(The flash is fixed to Forced ON [ ].)

• The flash setting is fixed to AUTO/Red-eye
reduction [ ] when the backlight
compensation function is set to [OFF].

Taking Pictures with the Zoom

Using the Optical Zoom/Using the
Extended Optical Zoom (EZ)

You can make people and objects appear
closer and landscapes can be recorded in
wide angle with the 3.6k optical zoom.
(35 mm film camera equivalent 28 mm to
100 mm) To make subjects appear even
closer (maximum of 5.3k), do not set the
picture size to the highest setting for each
aspect ratio ( / / ).

∫ To make subjects appear closer use

(Tele)

Rotate the zoom lever towards
Tele.

T

W

26

VQT1B86

∫ Picture size and maximum zoom

magnification

(±: Available, —: Not available)

Aspect

ratio

(P60)

Picture size

(P25, 61)

/(7M)

(5.5M)

(5M EZ) 4.3k±

(3M EZ)
(2M EZ)
(1M EZ)

/

(0.3M EZ)

/

(2.5M EZ)

(2M EZ)

Maximum

zoom

magnification

(Tele)

3.6k —(6M)

5.3k±

Extended

optical

zoom

∫ Extended optical zoom mechanism

When you set the picture size to [ ]
(3M EZ) (3 million pixels), the 7M (7 million
pixels) CCD area is cropped to the center
3M (3 million pixels) area, allowing a
picture with a higher zoom effect.

• The optical zoom is set to Wide (1k)
when the camera is turned on.

• If you use the zoom function after focusing
on the subject, focus on the subject again.

• The lens barrel (P9) extends or retracts
according to the zoom position. Take care
not to interrupt the motion of the lens
barrel while the zoom lever is rotated.

• In motion picture mode [ ], the zoom
magnification is fixed to the value set at
the start of recording.

• “EZ” is an abbreviation of
“Extended optical Zoom”.

• If you set a picture size that activates the
extended optical zoom, the extended
optical zoom icon [ ] is displayed on the
screen when you use the zoom function.

• The zoom will stop moving for an instant
near [W] (1k) when the extended optical
zoom is used. This is not a malfunction.

• The indicated zoom magnification is an
approximation.

• In motion picture mode [ ] and
[HIGH SENS.] in scene mode, the
extended optical zoom does not work.

Using the Digital Zoom

Further extending the zoom

A maximum of 14.3k zoom can be
achieved with the 3.6k optical zoom and
the 4k digital zoom when [D.ZOOM] is set
to [ON] in the [REC] mode menu. However,
if a picture size that can use extended
optical zoom is selected, a maximum of

21.4k zoom can be achieved with the 5.3k

extended optical zoom and the 4k digital
zoom.

∫ Menu operation

1 Press [MENU/SET].

• When a scene mode is selected, select
the [REC] menu ( ) and then press

1.

2 Press 3/4 to select [D.ZOOM]

and then press 1.

Basic

3 Press 4 to select [ON] and then

press [MENU/SET].

3

SET

/

3

1

/

㧙

8

OFF
ON

MENU

MENU

/SET

REC

SLOW SHUTTER
D.ZOOM
COL.MODE
CLOCK SET

SELECT

4 Press [MENU/SET] to close the

menu.

• You can also press the shutter
button halfway to close the menu.

∫ Entering the digital zoom range

The on-screen zoom indication may
momentarily stop moving when you rotate
the zoom lever to the extreme Tele position.
You can enter the digital zoom range by
continuously rotating the zoom lever to Tele
or releasing the zoom lever once and then
rotating it to Tele again.

W

≥[OFF]:

W

≥[ON]:

W

(When using the digital zoom and the
extended optical zoom [ ] (3M EZ) at the
same time)

1 Optical zoom
2 Digital zoom
3 Extended optical zoom

• A big AF area (P62) is displayed when
using the digital zoom. Also, the stabilizer
function may not be effective.

• In digital zoom, the larger the picture the
lower the picture quality.

T

T

T

27

VQT1B86

Basic

• When using the digital zoom, we
recommend using a tripod and the
self-timer (P38) for taking pictures.

• The indicated zoom magnification is an
approximation.

• The digital zoom does not work in the
following cases:
– In simple mode [ ].
– In intelligent ISO sensitivity mode [ ].
– In [SPORTS], [BABY1]/[BABY2], [PET]

and [HIGH SENS.] in scene mode.

Checking the Recorded Picture (Review)

∫ Enlarging the picture

1 Rotate the zoom lever towards

[] (T).

• Rotate the zoom lever to [ ] [T] for a
4k magnification and then rotate it
even more for a 8k magnification.
When you rotate the zoom lever
towards [ ] [W] after enlarging the
picture, the magnification becomes
lower.

2 Press 3/4/2/1 to move the

position.

REVIEW4X

You can check the recorded pictures while
still in [REC] mode.

1 Press 4 [REV].

REVIEW1X

DELETE

4X

EXIT

• The last recorded picture appears for
about 10 seconds.

• Review is canceled when the shutter
button is pressed halfway or the 4
[REV] is pressed again.

2 Press 2/1 to select the picture.

REVIEW1X

DELETE

4X

EXIT

2: Play back the previous picture
1: Play back the next picture

28

VQT1B86

1X

DELETE

8X

• When you change the magnification or
the position to be displayed, the zoom
position indication A appears for about
1 second.

∫ Deleting the recorded picture during

Review (Quick deletion)

A single picture, multiple pictures or all the
pictures can be deleted during review.
Refer to P29 to 30 for information about
how to delete pictures.

• When [ROTATE DISP.] is set to [ON],
pictures recorded holding the camera
vertically are played back vertically
(rotated).

Playing back/Deleting
Pictures

Basic

• In review playback in recording mode
and in multi playback (P67), the
pictures can only be forwarded or
rewound one by one.

The picture data on the built-in memory is
played back or deleted when a card is not
inserted. The picture data on the card is
played back or deleted when a card is
inserted. (P13)

Once deleted, pictures cannot be
recovered. Check the pictures one by
one and delete unwanted pictures.

∫ Playing back pictures

Press 2/1 to select the picture.

1/3

10:00 DEC. 1.2007

2: Play back the previous picture
1: Play back the next picture

∫ Fast forwarding/Fast rewinding

Press and hold 2/1 during playback.

1/3

10:00 DEC. 1.2007

2: Fast rewind
1:Fast forward

• The file number A and the picture
number B only change one by one.
Release 2/1 when the number of the
desired picture appears to play back the
picture.

• If you keep pressing 2/1, the number
of pictures forwarded/ rewound
increases.

• This camera is based on the DCF
standard “Design rule for Camera File
system” which was established by the
“JEITA (Japan Electronics and Information
Technology Industries Association)”.

• The LCD monitor may not be able to
display the details of the recorded
pictures. You can use the playback zoom
(P68) to check the details of the pictures.

• If you play back pictures that have been
recorded with other equipment, the picture
quality may deteriorate. (The pictures are
displayed as [THUMBNAIL IS
DISPLAYED] on the screen.)

• If you change a folder name or file name
on your PC, the pictures may not play
back on the camera.

• If you play back a non-standard file, the
folder/file number is indicated by [—] and
the screen may turn black.

• Depending on the subject, an interference
fringe may appear on the screen. This is
called moire. This is not a malfunction.

∫ To delete a single picture

1 Press [ ] while the picture is

being played back.

2 Press 3 to select [YES] and then

press [MENU/SET].

DELETE SINGLE

DELETE THIS PICTURE?

YES

NO

SELECT

MENU

SET

MULTI/ALL

• While the picture is being deleted, [ ]
appears on the screen.

MENU

/SET

29

VQT1B86

Basic

∫ To delete [MULTI DELETE]/

[ALL DELETE]

1 Press [ ] twice.
2 Press 3/4 to select

[MULTI DELETE] or
[ALL DELETE] and then press
[MENU/SET].

MULTI/ALL DELETE

MULTI DELETE

ALL DELETE

SELECT

SET

MENU

CANCEL

MENU

/SET

• [MULTI DELETE] > step 3.

• [ALL DELETE] > step

5.

• [ALL DELETE EXCEPT ] (When
[FAVORITE] (P74) is set only) >

5.

step
(However, this cannot be selected if
none of the pictures have [ ]
displayed.)

3 Press 2/1 to select the picture

and then press 4 to set.

(Only when selecting [MULTI DELETE])

MULTI DELETE

7

8 9

11

SELECT
MARK/UNMARK

DELETE

EXIT

1210

MENU

• Repeat the above procedure.

• [ ] appears on the selected pictures. If
4 is pressed again, the setting is
canceled.

• The icon [ ] blinks red if the selected
picture is protected and cannot be
deleted. Cancel the protect setting and
then delete the picture. (P79)

4 Press [ ].

5 Press 3 to select [YES] and then

press [MENU/SET] to set.

(Screen when selecting [MULTI DELETE])

MULTI DELETE

DELETE THE PICTURES
YOU MARKED?

YES

NO

SELECT

SET

• When you delete all pictures, only
pictures in either of the built-in memory
or the card can be deleted. (You cannot
delete pictures in both the built-in
memory and the card at the same
time.)

• [DELETE ALL PICTURES
ON THE BUILT-IN MEMORY?] or
[DELETE ALL PICTURES
ON THE MEMORY CARD?] is
displayed when using [ALL DELETE]
and [DELETE ALL EXCEPT ?] is
displayed when using
[ALL DELETE EXCEPT ].

• If you press [MENU/SET] while deleting
pictures using [ALL DELETE] or
[ALL DELETE EXCEPT ], the
deleting will stop halfway.

• Do not turn off the camera while deleting.

• When deleting pictures, use a battery with
sufficient battery power (P21) or the AC
adaptor (DMW-AC5PP; optional).

• It is possible to delete up to 50 pictures at
one time using [MULTI DELETE].

• The greater the number of pictures the
longer it takes to delete them.

• If there are pictures that are protected
[ ] (P79), do not conform to the DCF
standard (P29) or are in a card with the
Write-Protect switch slid to the [LOCK]
side (P13), they are not deleted even if
[ALL DELETE] or
[ALL DELETE EXCEPT ] is selected.

MENU

MENU

/SET

SET

30

VQT1B86