Panasonic CXCB-0910-FA Service manual
ORDER No.5040
AUTOMOTIVE ELECTRONICS
MITSUBISHI
CX-CB0910FA
6-Disc CD Changer
MITSUBISHI PART No. : A9000RCX01
ID CODE : P101
VEHICLE : UNIVERSAL
DESTINATION : North America
PRODUCED AFTER : Aug., 2001
I0
Specification*
General
Power Supply DC 12V (11V - 16V),
Test Voltage 13.2V
Negative Ground
Current Consumption Less than 1.0A
Output Voltage 1V (1kHz, 0dB)
CD Player
Total Harmonic Distortion 0.01% (1kHz)
Channel Separation 80dB (1kHz)
Frequency Response 10 - 20,000Hz
Quantization 16-bit linear
Wow and Flutter Below measuerable limits
Signal to Noise Ratio 96dB (IHF-A)
Dimensions** (W×H×D) 178 × 50 × 175mm
Weight** 1.3kg
* Specifications and the design are subject to possible modification
without notice due to improvements.
** Dimensions and Weight shown are approximate.
MITSUBISHI / CX-CB0910FA
CONTENTS
Page Page
1 FEATURES 2
2 LASER PRODUCTS
3 NAME AND FUNCTION OF EACH PARTS
4 REAR VIEW AND CONNECTOR
5 WIRING CONNECTION
6 BLOCK DIAGRAM (Main Block)
7 BLOCK DIAGRAM ( CD Servo Block)
8 TERMINALS DESCRIPTION
9 IC BLOCK DIAGRAM
10 CD DISC CENTERING ALIGNMENT 12
2
11 REPLACEMENT PARTS LIST
3
12 EXPLOD ED VIEW (Unit)
3
13 CD CHANGER PARTS LIST
4
14 EXPLOD ED VIEW (CD Deck-1)
5
15 EXPLOD ED VIEW (CD Deck-2)
6
16 EXPLOD ED VIEW (CD Deck-3)
7
17 WIRING DIAGRAM
10
18 SCHEMATIC DIAGRAM
1 FEATURES
·
IDC series CD changer deck (6-dics slots).
·
Shock Proof Memory.
·
MITSUBISHI M-BUS control.
2 LASER PRODUCTS
13
16
17
20
21
22
23
27
2
3 NAME AND FUNCTION OF EACH PARTS
4 REAR VIEW AND CONNECTOR
MITSUBISHI / CX-CB0910FA
3
MITSUBISHI / CX-CB0910FA
5 WIRING CONNECTION
4
6 BLOCK DIAGRAM (Main Block)
MITSUBISHI / CX-CB0910FA
5
MITSUBISHI / CX-CB0910FA
7 BLOCK DIAGRAM ( CD Servo Block)
6
8 TERMINALS DESCRIPTION
8.1. Main Block
MITSUBISHI / CX-CB0910FA
7
MITSUBISHI / CX-CB0910FA
8.2. CD Servo Block
IC201 : MN662783RPW
Pin
No.
1 VDD +5V power supply - 5.0
2 D0 D-RAM data I/O 2.3
3 D1 D-RAM data I/O 1.8
4 /WE D-RAM data write O 4.9
5 /RAS D-RAM row address strobe O 3.4
6 D2 D-RAM data I/O 0.8
7 D3 D-RAM data I/O 0
8 /CAS0 D-RAM columun address strobe O 3.9
9 /CAS1 D-RAM columun address strobe O 0
10 A8 D-RAM address O 0.6
11 A7 D-RAM address O 1.1
12 A6 D-RAM address O 0.7
13 A5 D-RAM address O 0
14 A4 D-RAM address O 1.1
15 A9 D-RAM address O 0.4
16-18 A0 D-RAM address O 1.0
19 A3 D-RAM address O 0
20 VSS2 Ground - 0
21 VDD2 +5V power supply - 5.0
22 PWMCK(NC) - - 23 TRVSTP(NC) - - 24 TVD Traverse motor control O 2.5
25 PC Not used - 26 ECS Spindle motor control O 2.4
27 TRD Tracking coil drive O 2.5
28 FOD Focus coil drive O 2.4
29 FBAL Focus balance O 1.9
30 TBAL Tracking balance O 3.0
31 VREF Refence voltage I 2.5
32 FE Focus error I 2.5
33 TE Tracking error I 2.5
34 RFENV RF envelope I 2.5
35 OFT Off track signal I 0
36 /RFDET RF detecting signal I 0
37 BDO Drop-out signal I 0
38 LDON Laser on signal O 4.5
39 ARF RF signal I 2.5
40 IREF Reference current input I 1.2
41 DRF Bias for DSL I 2.4
42 DSLF Loop filter for DSL I/O 2.5
43 DSLF2 Loop filter for DSL I/O 2.2
44 PLLF Loop filter for PLL I/O 1.4
45 VCOF(NC) - - 46 AVDD2 +5V power supply - 5.0
47 AVSS2 Ground - 0
48 OUTL L channel output O 2.3
49 AVSS1 Ground - 0
50 OUTR R channel output O 2.3
51 AVDD1 +5V power supply - 4.7
52-54 - (Connecting to ground) - 0
55 FLAG Flag output O 0
56 FCLK Frame clock O 0
57-59 NC - - -
60 TX(NC) - - 61 MCLK Clock for I/F command I 1.0
62 MDATA Date for I/F command I 3.1
63 MLD I/F command load I 5.0
64 BLKCK Subcode block clock O 0
65 SQCK Ext.clock for sub code-Q I 5.0
66 SUBQ Code for sub. code-Q O 3.8
67 DMUTE Mute input I 0
68 STAT Status signal O 5.0
Port Description I/O (V)
69 /RST Reset input I 5.0
70 CSEL (Connecting to ground) - 0
71 PMCK Clock output O 2.5
72 SMCK Clock output O 2.5
73 SUBC Serial data of sub code O 0
74 SBCK Shift clock for SUBC I 0.6
75 /CLDCK(NC) - - 76 /TEST (Connecting to VDD) - 5.0
77 X1 Crystal oscillator - 0.4
78 X2 Crystal oscillator - 3.2
79 VDD1 +5V power supply - 5.0
80 VSS1 Ground - 0
IC301 : MNS73260ACBL
Pin
No.
1 VDD +5V power supply - 5.0
2 OSC2 Crystal oscillator - 2.2
3 OSC1 Crystal oscillator - 2.1
4 VSS Ground - 0
5 XI (Connecting to ground) - 0
6 XO(NC) - - 7 CM (Connecting to ground) - 0
8 VREFH Reference voltage I 5.0
9 SW13 Shuter SW I 4.9
10 SW12 Horizontal origin I 4.9
11 SW11 Clump SW I 0
12 SW10 Play SW I 0
13 SW4 Shuter SW I 4.9
14 SW3 Tray origin SW I 0
15 SW2 Inner SW I 4.8
16 SW1 Outer SW I 4.9
17 VREFL Reference voltage I 0
18 /RESET Reset input I 4.9
19 - (Ground pull-down) - 0
20 SCKM Clock for serial data I 5.0
21 SIM CD changer serial data I 1.3
22 SOM CD changer serial data O 4.3
23 SQCK Ext. clock for sub. code-Q O 5.0
24 SUBQ Code for sub. code-Q I 1.6
25 NC - - 26 - (Ground pull-down) - 0
27 CD.ON CD changer start/stop I 5.0
28 NC - - 29 BLKCK Sub. code block clock I 0
30 P.ON Power switch on - 5.0
31 MUTE Mute output O 5.0
32 - (Ground pull-down) - 0
33 SENS Servo status O 0
34 CLVS Servo status O 5.0
35 FLOCK Focus servo lock O 0.2
36 TLOCK Tracking servo lock O 0
37 VMI Horizontal motor control O 2.5
38 HMI Vertical motor control O 0
39 HVMUTE H/V motor mute O 0
40-42 - (Ground pull-down) - 0
43 SW9 Disc-in (B) SW I 0
44 SW8 Disc-in (L) SW I 0
45 SW7 Disc-in (F) SW I 0
46 SW6 Disc push SW I 0
47 SW5 Tray hight SW I 4.5
48 BDO Drop-out signal I 0
49 DQSY(NC) - - 50 /RST Reset output O 5.0
51 STAT Status signal I 2.1
52 DMUTE Mute output O 0
Port Description I/O (V)
8
53 XE(NC) - - 54 P.DOWN Power down signal O 0
55 - No connection - 56 MLD I/F command load O 5.0
57 MDATA Data for I/F command O 3.1
58 MCLK Clock for I/F command O 4.1
59 SPMT Spindle mute O 5.0
60 MUTE12 Focus/Tracking mute O 0
61 MUTE4 Loading motor mute O 4.8
62 LDOI Loading motor control I/O 2.5
63 TRV Forced traverse control I/O 2.4
64 SYNC(NC) - - -
MITSUBISHI / CX-CB0910FA
9
Loading...