Panasonic CT-27S7CA Owner’s Manual

............. I I ....

just slightly ahead of our time®

D

_!i' i

Your new TV Monitor/Receiver features a solid
state chassis that is designed to give you many

years of enjoyment. It was thoroughly tested and
tuned at the factory for best performance.

Customer Record

The model and serial number of this product may

be found on the back of the unit. You should note
the model and serial number in the space provided

and retain as a permanent record of your

purchase. This will aid in identification in the event

of theft or loss.

Model
Number

Serial
Number

Care and Cleaning
Screen (Turn TV Off)

Use a mild soap solution or window
cleaner with a soft clean cloth. DO NOT
USE ABRASIVE CLEANERS.

Avoid excessive moisture and wipe dry.

Cabinet and Remote Control

Use a soft cloth dampened with water or
a mild detergent solution. Do not use
benzene, thinner, or other petroleum

based cleaners.
Wipe dry with a soft clean cloth. Avoid

excessive moisture.

S _ecifications

Power Source

CT-27G14D CT-27S7C
CT-32G14C CT-27G4C

Channel Capablgty. 181

Video Input Jacks

(some models)

!

Audio Input Jacks

(some models)

To Audio AMP Jack

(some models)

3ecificationsare subjecttochange withoutnotic

orobligation.

120V AO, 60Hz

VHF-12; UHF-
56; Cable-113

1Vpp, 75 Ohm,

PhonoJack Type

500mV RMS47K

0-2.OV RMS

Ohm

4.7K Ohm

Television Location

This unit is intended to be used with an optional
stand or entertainment center. Consult your dealer

for available options.
O Avoid excessive sunlight or bright lights,

including reflections.

O Keep away from excessive heat or moisture.

Inadequate ventilation may cause internal

component failure.

C3 Fluorescent lighting may reduce Remote

Control transmitting range.

£3 Avoid magnetic equipment, including motors,

fans, or external speakers.

Optional Cable Connections

Shielded audio and video cables should be used
between components.Forbest results:

Use 75-ohmcoaxial shielded cables.
Use appropriate input and output

connectors that match your
component connectors.

Avoid long cables to minimize
interference.

AC Power Supply Cord

CAUTION: TO PREVENT

ELECTRIC SHOCK, MATCH B_" I_
WIDE BLADE OF PLUG TO
WIDE SLOT OF AC OUTLET Potadzed plug

AND FULLY INSERT. DO ,_-_
NOT USE A PLUG WITH A

RECEPTACLE OR OTHER NomPolarizedplug
OUTLET UNLESS THE

BLADE CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE. FOR SOME MODELS THAT

ARE NON-POLARIZED, THE USE OF AN AC
ADAPTOR CONNECTOR MAY BE NECESSARY,

Batteries

Replace batteries in pairs.
Do not mix battery types (zinc carbon

with alkaline).

Do not recharge, short-circuit,

disassemble, heat, or burn used

batteries,

Cable / Antenna

For proper reception, either a cable or antenna

connection are required.

Cable Connection

Connect the cable supplied by your local
cable company.

Incoming Cable fromCable Company

-2-

Note:

75 Ohms VHF/UHF

on back of TV

A cable converter box may be required

for proper reception. Check with your

local cable company for compatibility

requirements.

Antenna Connection

For proper reception of VHF/UHF
channels, an external antenna is required

For best reception an outdoor antenna is
recommended.

Antenna Mode must be set to TV.

VHF/UHF Antenna

A VHF/UHF antenna and transformer are supplied
in _. Attach to the TV, adjust the

antenna until the picture is clear. (See Antenna
Connection).

Incoming Cable from Home Antenna

Helpful Hints: Cable Preset

Cable Mode is preset at the factory Antenna users
must change to Antenna Mode in the Set Up Menu.

O

e

:0
rn

r-

e

(/J

"o

Optional Equipment

Connections

VCRs, video disc players, video game equipment,

and DSS equipment can also be connected to the
antenna input connection. (See your equipment

manual),

Procedure

1. Connect equipment as shown to Front or
Rear AudioNideo input jacks.

Note: Front and Rear Audio/Video

connections cannot be

operated at the same time.

2. Select the Video mode by pressing TV/

VIDEO button.

3. Operate optional equipment as instructed
in equipment manual.

Note: ff both S-VIDEO and VIDEO input are

used at the same time, two images will
appear on the television screen.

Terminals on back of TV (some models) VCR or Video Disc

To Audio Amplifier (AMP, some

models)

Connect to an external audio amplifier input for

listening to sound from a stereo system

Note: TO AUDIO AMP terminals cannot be used

directly for external speakers.

Audio Adjustments

1. Press TV SPEAKERS ON button located
on back of set.

Note: If your TV does not have a TV

SPEAKERS ON/OFF button,
select TV SPEAKERS ON from

AUDIO menu,

2. Set amplifier volume to minimum.

3. Adjust TV volume to desired level

4. Adjust amplifier volume to match the TV

5. Press TV SPEAKERS OFF button located

on back of set.

Note: If your TV does net have a TV

SPEAKERS ON/OFF button,
select OFF&VAO from AUDIO

menu.

6. Volume and mute are now selected using
the TV controls,

Note: In OFF&FAO the volume is controlled by

the external amp/ifie_

l

r..
f..

e

o0

r-

e

(3

"10

oI

:o,.o,o

.zA.O.O .,o.o"! : --"

S-(_)EO __ @ @ _ (Cables notsupplieb) __l

Jack used for VIDEO L-AUDIO* R

t/8" headph°ne plug _"_J_ _ _ @ _)_

Terminals on front of TV (some models)

==_dll

-- -- Terminals on back of VCR

-3-

Ill

I11

(3