How it Works
Panasonic
Loading...
CT-27HL14J
Owner’s Manual
80 pgs10.1 Mb0

Panasonic CT-32HXC14J, CT-32HC14J, CT-27HL14J Owner’s Manual

F=I°D
CT-27HL14 CT-32HXC14
CT-32HC14
TQB2AA0501-2 40330
PRINTED IN USA IMPRESO EN EE.UU
IMPRIM¢: AUX €:TATS-UNIS
Important Information
FCC CAUTION: ANY CHANGES OR MODIFICATIONS TO THIS TV RECEIVER NOT EXPRESSLY APPROVED BY
MATSUSHITA ELECTRIC CORPORATION OF AMERICA COULD CAUSE HARMFUL
INTERFERENCE, WHICH WOULD VOID THE USER'S AUTHORITY TO OPERATE THIS
EQUIPMENT.
FCC INFORMATION This equipment has been tested and found to comply with the limit for a Class B Digital Device in
accordance with the specifications in Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against radio and television interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to radio or television reception, which you can determine by turning the equipment off and on, try to correct the interference by one or more of the following measures.
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
IMPORTANTINFORMATION
ENVIRONMENTAL NOTICE:
THIS PRODUCT UTILIZES CATHODE RAY TUBES (CRT) AND OTHER COMPONENTS THAT CONTAIN LEAD. DISPOSAL OF THESE MATERIALS MAY
BE REGULATED IN YOUR COMMUNITY DUE TO ENVIRONMENTAL CONSIDERATIONS. FOR DISPOSAL OR RECYCLING INFORMATION PLEASE
CONTACT YOUR LOCAL AUTHORITIES, OR THE ELECTRONICS INDUSTRIES ALLIANCE: <HTTP ://WWW. EIAE.ORG.>
The Energy Star label, a symbol for energy efficiency, was created by the U.S.
Environmental Protection Agency (EPA) and the U.S. Department of Energy (DOE) to help customers identify products that can save them money and protect the
environment by saving energy. Energy Star compliant products generally consume less energy than similar standard products.
Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under USP4638258, 5510752 and 5736897.
High Definition Sound
BBE and BBE symbol are registered trademarks of BBE Sound, Inc. BBE High Definition Sound restores clarity and presence for better speech
intelligibility and music realism.
Important Information Regarding The Use of Video Games, Computers, Or Other Fixed Image Displays
WARNING: The marking or retained image on the picture tube resulting from viewing fixed image is
not an operating defect and as such is not covered by Warranty.
The television is designed to display constantly moving images on the screen. Continuous viewing of stationary images such as letterbox pictures on standard screen TVs (with top/bottom bars), non-expanded standard (4:3) pictures on wide screen TVs (with side bars shown on each side of an image), stock market
report bars (ticker running at the bottom of the screen), video game patterns, fixed scoreboards, bright station Iogos, on-line (tnternet) or repetitive computer style patterns should be limited.
The extended use of fixed image program material can cause permanent picture tube damage, shown as a "shadow image" viewable on normal programs. This type of irreversible picture tube deterioration can be
limited by performing the following steps:
Limit the display of fixed image program materialto no more than 15% of totalviewing time perweek.
Turn the power off when not inuse.
10
Congratulations
Your new Panasonic Tau television features state-of-the-art technology for high quality picture and sound with complete
audio/video connections for your home theater system. Your TV is designed to give you many years of enjoyment.
It was thoroughly tested and tuned at the factory for best performance.
Customer Record
The model and serial number of this product are located on the back of the TV. You should note the model and serial
number in the space provided and retain as a permanent record of your purchase. This will aid in identification in the event of theft or loss. Product registration for U.S. customers is available at: www.prodreg.com/panasonic.
Model Number
Serial Number
Care and Cleaning
Screen (Turn TV Off)
Use a mild soap solution or window cleaner with a soft clean cloth. DO NOT USE ABRASIVE CLEANERS.
Avoid excessive moisture and wipe dry.
Warning: Do not spray any type of cleaning fluid directly on the
screen.
Cabinet and Remote Control
For cabinets and remote control, use a soft cloth dampened with water or a mild detergent solution. Avoid excessive moisture and wipe dry. Do not use benzene, thinner or other petroleum based products.
Specifications
Specifications are subject to change without notice or obligation.
Power Source
CT-27HL14 (3.2A)
CT-27HL14U (3.2A)I
CT-27HL14M (3.2A) i2 VA 60
CT=27HL14MU (3.2A) O C, HZ
c'r=32HC14 (3.6A)
CT-32HC14U (3.6A)
c'r=32HXC14 (3.6A) c'r=32HXC14U (3.6A)
Channel Capability - 181 VHF-12; UHF-56; CabZe-113
Video Input Jacks 1Vp-p, 75 Ohm, Phono Jack Type
Audio Input Jacks • 500mV RMS 47K Ohm
Video out jack 1Vp-p, 75 Ohm, Phono Jack Type
Audio Output Jacks • 0-2.0V RMS 4.7K Ohm
DVl Input jack • 1.0 compatible
Component Input (Y / PB/ PR) ' 75 Ohm, Phono Jack Type
S-Video Input Jacks " S-Video (Y-C) Connector
Feature Chart
FEATURES
MENU LANGUAGE ENG/ ' '
V-CHIP CAPABILITY
CHANNEL INFO BANNER ' • ' • •
VIDEO INPUT SKIP
VIDEO PICTURE MEMORY
DIGITAL SCAN RATE t080i, 1080i, t080i,
NTSC LINE-DOUBLER 480p 480p 480p
VIDEO NORM
AUDIO NORM • • •
BASS/BALANCE/TREBLE • ' • ' •
SURROUND • ' • •
A/V IN (REAR/FRONT) , ' '
COMPONENT INPUTS 1 2 2
S-VIDEO INPUT 1/0 2/1 2/1
(REAR/FRONT) I I I
A/V PROGRAM OUT
HEADPHONE JACK , • •
CONGRA TULA T/ONS
MODELS
•4 (J
t_ 04 o_ oq 03 o3
€. €. _L (J (J L_
SPAN/FR . . .
I I
I I
I I I
480p 480p 480p
I I
I I
i i
STEREO
AI SOUND • • •
I I
I
I I
BBE ' '
4 4 4
(3/1) (3/1) (3/1)
i
I I I
3o
Initial Set Up Menu
For your convenience, Auto Set up menu will be displayed on screen when the set is turned on for the first time. If
needed, follow the menus and procedures for setting up the
features.
IDIOMA/LANGUE
To change menu language to ENGLISH, SPANISH or FRENCH.
Procedure
Press VOL • to select English, Spanish or French.
FIRST PLEASE
CONNECT THE ANTENNA
INITIAL SET UP
IDIOMA/LANGUE ENGLISH 1_ MODE CABLE 1_ AUTO PROGRAM 1_
GEOMAGNETIC CORRECTION 1_ TILT CORRECTION 1_
PRESS ACTION TO EXIT
MODE To select TV (antenna) or CABLE mode depending on the
signal source. Procedure
Press VOL • to select TV or CABLE.
FIRST PLEASE
CONNECT THE ANTENNA
INITIAL SET UP
IDIOMA/LANGUE ENGLISH I_
MODE CABLE I_
AUTO PROGRAM 1_ GEOMAGNETIC CORRECTION I_
TILT CORRECTION I_
PRESS ACTION TO EXIT
AUTO PROGRAM
To automatically program all channels with a signal. Procedure
Press VOL • to start Auto Programming.
INITIAL SET UP MENU
GEOMAGNETIC CORRECTION This feature is used to adjust discoloration of the picture
due to the earth's magnetic field in the area. Procedure
Press VOL • to display adjustment menu. Press • VOL or VOL • to adjust discoloration in picture.
FIRST PLEASE ]CONNECT THE ANTENNA
INITIAL SET UP 1
MODE CABLE Ii_ AUTO PROGRAM • GEOMAGNETIC CORRECTION • TILT CORRECTION •
IDIOMA/LANGUE ENGUSH • 1
PRESS ACTION TO EXIT
Note: Geomagnetic Correction is net available in model
CT-27HL14.
TIN CORRECTION This feature is used to adjust the tilt of the picture due to
earth's magnetic field in the area.
Procedure
Press VOL • to display adjustment menu. Press • VOL or VOL • to adjust picture tilt.
FIRST PLEASE
CONNECT THE ANTENNA
IDIOMA/LANGUE ENGLISH • MODE CABLE •
AUTO PROGRAM •
GEOMAGNETIC CORRECTION • TILT CORRECTION •
INITIAL SET UP
PRESS ACTION TO EXIT
I FIRST PLEASECONNECT THE ANTENNA
IDIOMA/LANGUE ENGLISH i_
GEOMAGNETIC CORRECTION i_ TILT CORRECTION It*
AuToMODEPROGRAMpRESSACTION TO EXII ABLE I_1_
INITIAL SET UP
5o
VCR and Cable Box Connection (Cont.)
Recording a premium (scrambled) cable channel Procedure
Press the TV/VlDEO button and the numeric keys on the remote control to select the video input (VIDEO 1, VIDEO 2, etc.) connected to your VCR.
Turn the VCR ON. Tune the VCR to Channel 3 or 4, depending on the
switch setting on the back of VCR. Using your cable box, tune to the premium cable channel you want to record. Begin recording.
[_ To view a different channel while recording:
Press the TV/VlDEO button and the numeric keys on the remote control to TV mode.
Tune the television to a program (except another premium cable channel).
Amplifier Connection (TO AUDIO AMP)
To listen to the audio through a separate stereo system, connect an external audio amplifier TO AUDIO AMP outputs on back of television.
Note: TO AUDIO AMP terminals can not be connected directly
to external speakers.
OPTIONAL EQUIPMENT CONNECTIONS
Digital TV - Set-Top Box (DTV-STB) or DVD Connection
This television is capable of displaying 1080i and 480p DTV signals when connected to a DTV tuner set-top-box (STB). In
order to view DTV programming, the STV must be connected to the component video inputs (Y,PB,PR) of the television. A
DTV signal must be available in your area. Select the output of the STB to either 1080i or 480p.
This television also utilizes a progressive scan doubler, which de-interlaces the NTSC signal and progressively scans the
image. This allows you to sit close to the TV and not see the thin black horizontal lines (venetian blind effect) associated with interlaced TV pictures.
Use this diagram to connect the DTV-STB (Digital TV Set-Top-
Box) or DVD player to the back of television.
TERMINALS ON BACK OP BTV.STB OR DVD PLAYER /
TERMINALS ON BACK OF TELEVISION
l__ J -_ °°°°°°_
ITALINPUT
o..o.ooo.......uz
j,_., @ @@@@@
Note: Rear A/V jacks diagram may vary, depending on model.
Audio Adjustments
Note: Select SPEAKERS OFF & FIXED AUDIO OUT to control
OOOOOO_ _
o............... x......
VIDEOIr_PUT AMP
Please refer to the FEATURE CHART on page 3 for your model's capabilities.
Select SPEAKERS ON located in the onscreen AUDIO menu.
Set amplifier volume to minimum. Adjust television volume to desired level. Adjust amplifier volume to match the television.
Select SPEAKERS OFF & VARIABLE AUDIO OUT from AUDIO menu.
Note: Variable Audio Out is not available in model
CT-27HL14.
Volume, mute, bass, treble and balance are now
controlled through the television.
audio functions through the external amplifier.
Note: Rear A/V jacks diagram may vary, depending on model.
Please refer to the FEATURE CHART on page 3 for your model's capabilities.
Front Control Panel
The front control panel can be used to access menus and switch video mode when the remote control is not
available.
Note: The ON/OFF indicator LED (red) will be lit when set
is on.
Frontpanelfor C%32HC14
ON/OFFINDICATONpOWENON/OFF
,_OLUME_ _. _HANN,_ A(q_ION TV_EO S_O VE@)EOL@AUDIO@R _
FrontpaneJForCT-27HL14
A second VCR, Camcorder, a video disc player, video
game equipment or DSS equipment can also be connected
to the video inputs. See the optional equipment manual for
details.
Procedure
Connect equipment to front Audio/Video input jacks. Press TV/VIDEO button and the numeric keys to select VIDEO 4 input mode. Operate optional equipment as instructed in equipment
manual.
7O
Remote Control Operation
REMOTE CONTROL OPERATION
Press to turn ON and OFF.
Press to select remote operation.
ACTION
@
Press to access TV Menu.
MUTE
O
Press to mute sound, press to display and
cancel _ (Closed Caption).
TV/VIDEO
O
Press to select TV or Video mode.
MENU
Press to access DVD and DBS menus.
Press to select audio modes(Stereo, SAP or II
Mono). II
Press to adjust TV sound and navigate in II
menus. II
CH CH
Press to select next or Previous channel and navigate in menus.
I/andother options. II
GUIDE
O
DBS functions button.
EXIT
DBS functions button.
Press numeric keypad to select any channel.
EUR7613ZB0
Press to enter the minor number in a I
I/compound channel number (DBS mode only). II
REW
PAUSE
Component function buttons
PLAY FF
STOP ' REC
DVD/VCR CH
9O
Programming The Remote Control
The Universal Remote Control can be programmed to operate many manufacturers' components, using the component function buttons for VCR, DVD, CABLE or DBS. Follow the procedures for programming your Remote Control with or without a code for the component.
TV TV (Panasonic Only) Panasonic Code VCR I VCR (Preset) . Panasonic Code
DBS/CBL DBS STB & CBL STB (Preset) Panasonic DBS Code DVD : DVD (Preset) t Panasonic Code
Note: Determine the manufacturer of the component and look
in the table for the code (found on page 12).
Procedure
1. Confirm that the external component is plugged in and operating.
2. Turn the component off.
ACTION
3. Press and together, for at least 5 seconds. After 5 seconds, the illuminated mode (component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press appropriate component button on the Remote Control VCR, DVD, CABLE or DBS. The component
button will illuminate steadily and all others will go out.
5. Enter the 3-digit component code using the Remote Control numeric keypad (0 ~ 9 buttons). The component
button will blink twice.
6. Press the Remote Control to test the component. If the procedure was successful, the
component will turn on and the component key will blink twice and then go out.
Note: If the component does not operate with the Remote
Control, repeat steps 3 through 6 using another code (some brands have multiple codes). If an incorrect code is entered, or ff the procedure takes longer than 30 seconds, the programming will fail.
Programming Without A Code
This procedure searches all codes and is called the "sequence method."
1. Confirm that the external component is plugged in and
on.
2. Turn the component off.
ACTION
3. Press and together, for at least 5 seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press the appropriate component button on the Remote Control. The component button will illuminate steadily and all others will go out.
REMOTE CONTROL OPERATION
Press VOL • (the mode key will blink three times), then
press the Remote Control button to test the component. Continue this process until the proper code
is found. If the procedure was successful, the component will turn on.
Note:
Note:
Each time you press the VOL • button, make sure that the component key blinks twice before pressing the
POWER button.
8.
Once the device responds, press to store the code. The mode (component) button will blink twice.
It may take many attempts before the correct code is found. If you miss a code, press 41 VOL, then press
the button to test the component.
ACTION
Component Codes
The Universal Remote Control is capable of operating many component brands after entering a code. Some components may not operate because the codes are not available due to limited memory. The Universal Remote
Control does not control all features found in each model.
JiJ |iJliiJill i I
VCR CABLE DVD
III IIII IIII
DBS
ill :
5. Press the button to set the remote control into the step and set mode.
6. Point the remote control towards the component.
11e
Basic Menu Navigation
Press to display the
Main Menu.
BASIC MENU NAWGATtON
V
Press to choose the
desired icon.
Press to enter the sub-
menu field.
Press to select desired
sub-menu.
sub Menu Field
Press
Press
Press
to enter sub sub-menu field.
sub sub- Menu Field
to select desired sub sub-menu.
to select or adjust
desired sub sub- menu.
Note: To EXIT menus.
Press d_[__ to select or adjust
desired sub-menu.
Note: For sub -menu with OTHER ADJ.
Press to select OTHER ADJ.
BRIGHTNESS 32 I
Press
Press
repeatedly until Main Menus icon
is highlighted.
Main Menu Icon
to exit Main Menu.
Normal Picture
13e
CHANNELS
[] CHANNEL SCAN - Select FAV or ALL.
Note: Use remote numeric keypad to select desired FAV
channels.
[] FAVORITES - To enter up to 16 favorite channels. Use
remote control numeric keypad to select desired channels.
[] OTHER ADJ. Highlight OTHER ADJ. and press VOL • to display the sub
sub-menu.
PRESET CAPTION - To enter channel numbers for popular TV stations.
Procedure
Press CH • to select desired preset caption. Then use the remote numeric keypad to select desired channel (refer to your local TV guide).
ICON MENUS OPERATION
Procedure
Press CH • or CH • to select the desired Video input.
Press 4 VOL or VOL • to select desired preset input label (see chart below).
INPUT LABEL CHART
VCR Se]ect when VCR is connected to video input.
DVD Select when DVD is connected to video input. SKIP Select to skip unused video input when
CABLE Select when CABLE box is connected
DBS Select when DBS is connected to video input.
DTV STB connected
PVR (Personal Select w hen a personal video recorde r is Video Recorder) connected to video input.
GAME Select when Video GAME is connected
AUX Select when other component s are
. pressing TVNIDEO button.
. to video input.
Select when digital TV set-t0P:bOx is
. to video input.
' to video input.
. connected: ' Select to delete input label.
TIMER
Note: Use OH • or CH • to highlight and use 4 VOL or
VOL • to select.
Note:
Note:
To delete a channel press "4 VOL while channel
number is highlighted.
MANUAL CAPTION - To enter numbers and captions manually.
Use the remote numeric keypad to select desired channel (refer to your local TV guide).
INPUT LABEL - To label video input connections for onscreen display.
This menu is for model CT-27HL14 only.
[] SLEEP - Select to turn TV off in 30, 60, or 90 minutes.
Select NO to turn sleep timer off.
[] TIMER 1 and TIMER 2 - Select one or both timers to
turn the TV on and off at selected times, on selected channel, and on selected days.
Notes:
The television automatically turns OFF after 90 minutes when turned ON by the TIMER. If the OFF time is selected or if a key is pressed, the automatic OFF after
90 minutes will be cancelled. The TIMER is active when the television is OFF or ON. The television will switch to the selected channel at the selected time set in the TIMER.
[] CLOCK SET - Set the time of the day and the day of
the week.
15e
LOCK (cont.)
U.S TV Programs (cont.)
Customer Caution
The V-Chip system that is used in this set is capable of blocking "NR" programs (non rated, not applicable and none) per FCC
Rules Section 15.120(e)(2). If the option of blocking "NR" programs is chosen "unexpected and possibly confusing results may occur, and you may not receive emergency bulletins or any of the following types of programming:"
Emergency Bulletins (Such as EAS messages,
weather warnings and others)
Locally originated programming News
Political Public Service Announcements
Religious
Sports Weather
U.S. TV Programs Rating Chart Description
NR Not Rated. SEE CUSTOMER CAUTION above.
All children. The themes and elements in this
TV-Y program are specifically designed for a very young
audience, including children from ages 2-6. Directed to older children. Themes and elements
TV,Y7 in this program may include mild physical or
TV-G no strong language, and little or no sexual dialogue
TV-PG
TV-14 contain sophisticated themes, sexual content
TV-MA mature themes, profane language, graphic violence
FV FANTASY/CARTOON VIOLENCE
V VIOLENCE
S SEX L OFFENSIVE LANGUAGE D DIALOGUE WITH SEXUAL CONTENT
U.S. Movies This TV model features the "V-Chip technology" which
allows you to use Motion Picture Ratings when viewing movies or video tapes. This innovation allows parents to block various types of movies and video tapes at their
discretion.
comedic violence, or may frighten children under
the age of 7.
General audience. It contains little or no violence,
or situations.
Parental guidance suggested. The program may contain infrequent coarse language, limited
violence, some suggestive sexual dialogue and
situations. Parents strongly cautioned, This program may
strong language and more intense violence. Mature audiences only. This program may contain
and explicit sexual content.
ICON MENUS OPERATION
Note: Some movies are net rated for a variety of reasons. Old
movies and foreign films are usually not rated.
Procedure
Press CH • or CH • to move between different ratings. Use ,q VOL or VOL • to select ratings you want to block (RED) and unblock (GREEN).
ACTION
Press _ to return to V-CHIP SET. Press CH • to select HOW LONG?
Press ,q VOL or VOL • to select 12, 24, 48 hours or ALWAYS.
ACTION
Press _ to return to Main Menu, then press CH • to exit.
U.S. Movies Rating Chart Description
NR (NOT APPLICABLE) PROGRAMS. Movie has
G GENERAL AUDIENCES. All ages admitted.
PG
PG-13 material may be inappropriate for children under
R RESTRICTED, Under 17 requires accompanying
N0-17 NO ONE 17 AND UNDER ADMITTED.
X ADULTS ONLY,
CONTAINS NO RATING (NOT RATED) AND NA
not been rated or rating does not apply.
PARENTAL GUIDANCE SUGGESTED. Some
material may not be suitable for children.
PARENTS STRONGLY CAUTIONED. Some
13.
_arent or adult guardian.
Canadian English The V-CHIP used in this TV model allows you to block
various types of movies and television programs based on the two rating systems used in Canada.
17e
LOCK (cont.)
Blocking Message If V-Chip is enabled and the program exceeds the rating
limit set by you, the blocking message will appear and the audio will be muted. Enter your four-digit secret code if you
wish to continue viewing the program. After entering your
code, all locks and rating blocks are disabled until the TV is turned off or until all settings are off.
Note: If you enter your four-digit secret code to override rating
blocks, you must reset all rating blocks by either reprogramming or turning the TV off.
Main Picture
PROGRAM RATING EXCEEDED
ACCESSCODE -- -- --
ICON MENUS OPERATION
T1 to T4 - For program guide and other information to be displayed, when available. (Blocks a large portion of the picture on the television screen).
Note: C1 mode is recommended for viewing Closed Caption. [] OTHER ADJ.
Highlight OTHER ADJ. and press VOL • to enter sub sub- menu field.
Note: While sub sub-menu features are highlighted, press
VOL i_ to adjust or activate.
SET UP
[] While the desired sub menu is highlighted, press VOL I_ to
select or activate feature.
[] IDIOMA/LANGUE - Select to change menu language
to ENGLISH, ESPAKIOL (Spanish) or FRAN(_AtS (French).
[] _ ON MUTE - Activates the onscreen Closed
Caption feature when the MUTE button on the remote control is pressed. To deactivate press MUTE again.
[]
MODE - This television contains a built-in decoder
that displays _ (Closed Captioned) text across the screen (white or colored letters on black background).
It allows the viewer to read the dialogue of a television program or other information. The program viewed must include Closed Captioning for the feature to work. Activate the onscreen Closed Caption feature by selecting one of the following modes.
OFF - When Closed Caption is not desired. C1 - For video related information to be displayed, up to
4 lines onscreen at a time. (It does not block relevant
parts of the picture). Text may be in any language. C2 to C4 - For other modes of video related information.
Note:
MODE - To select TV (antenna) or CABLE mode depending on the signal source. AUTO PROGRAM - To automatically program all channels with a signal. MANUAL PROGRAM - To manually add or delete
channels. AUTO POWER ON - Select SET to power up the TV at
the same time as the Cable box or other components or select OFF.
CHAN BANNER - Select ON to display onscreen banner when changing channels. GEOMAGNETIC CORR - This feature is used to adjust discoloration of the picture due to earth's magnetic field
in the area.
Geomagnetic Correction is not available in model CT-27HL14.
TILT CORRECTION - This feature is used to adjust the tilt of the picture due to earth's magnetic field in the area.
IMAGE SHIFT - This feature prevents the image retention associated with viewing a fixed image for a long period of time. When this feature is selected (ON), the image is shifted up or down in small increments at turn ON, when changing channels or when the fixed image is left On for a long time. Selecting ON is
recommended for this feature.
19e
Index
AC Power Supply Cord 4 AI Sound 14
Amplifier Connection 7 Antenna Connection 4
Aspect 14 Audio 14
Auto Power On 19 Auto Program 5, 19
Balance 14 Basic Menu Navigation 13
Bass 14 BBE 14
Blocking Message 19 Brightness 14
Cabinet and Remote Control 3 Cable / Antenna Connection 4
Cable Box Connection 6 Cable Connection 4 Canadian English 17
Canadian English Rating
Description 18
Canadian French 18 Canadian French Rating
Description 18
Care And Cleaning 3 Chan Banner 19
Channel Scan 15 Cinema 14
Clock Set 15 Codes For Cable Box 12
Codes For DBS 12 Codes For DVD 12
Codes For VCR 12 Color 14
Color Matrix 14 Color Temp 14
Component Codes 12 Customer Record 3
Digital TV - Set-Top Box (DTV-STB)
or DVD Connection 7
DVl (Digital Visual Interface) input
connection 8
Enter Code 16
Favorites 15 Feature Chart 3
Front Control Panel 7
Geomagnetic Corr 19 Geomagnetic Correction 5
Icon Menus Operation 14 Idioma/langue 5, 19 Image Shift 19 Initial Set Up Menu 5 Input Label 15 Input Label Chart 15
Installation 4
Lock 16 Lock Set 16
Manual Caption 15 Manual Program 19
Mode 19 Mono 14
Natural Color 14 Normal 14
On Mute 19 Operating a Cable Box 10
Operating a DBS 10 Operating a DVD 10 Operating a VCR 10 Operating Components with Remote
Control 10
Optional Cable Connections 4 Optional Equipment Connections 6 Other Adj. 14
Pic Mode 14 Picture 14
Preset Caption 15
INDEX
Program Out Connection (Prog Out) 8 Programming The Remote 11 Programming Without A Code 11
Remote Control Battery Installation 4 Remote Control Operation 9
SAP 14 SAP Button 8 Screen 3
Set Up 19 Sharpness 14 Sleep 15 Speakers 14 Special Remote Button 8 Specifications 3
Standard 14 Stereo 14 Surround 14
Television Location 4 Tilt Correction 5, 19
Timer 14, 15 Timer 1 And Timer 2 15 Tint 14
Treble 14 Troubleshooting Chart 20
U.S TV Programs 16 U.S. Movies 17
U.S. Movies Rating Chart
Description 17 U.S. TV Programs Rating Chart Description 17
V-Chip Set 16 VCR and Cable Box Connection 6, 7
VCR Connection 6 Velocity Modulation 14
Video NR 14 Vivid 14
21 •
Loading...
+ 56 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use