Frequency Range531 - 1602kHz
Usable Sensitivity25 dB/µV
Image Rejection Ratio50 dB
Audio Section
Output voltage/Impedance2 Vrms/600 Ω
Frequency Characteristics
(When “LARGE” is Selected)
4Ω
1.0 Vp-p (75Ω)
1.0 Vp-p (75Ω)
Front L/R, Center,
Rear (Surround) L/R
Delay Time
Dolby Digital
Center0-5ms
Rear (Surround) L/R0 -15 ms
Dolby Pro Logic
Rear (Surround) L/R15-30 ms
Distortion
Front L/R0.01% (1kHz,0dB,PCM Input)
Dynamic Range96dB (During CD Playback)
S/N Ratio100dB (During CD Playback)
Monitor
Storage temperature range-20°C - 80°C
Liquid Crystal Panel6.5” wide
Screen Dimensions (W×H×D) 134 × 79 × 164mm
Number of Pixels280,880 pixels
Valid Pixel RatioOver 99.99%
Display MethodTransparent color filter format
Drive MethodTFT (Thin Film Transistor)
Light SourceInternal light
Dimensions** (W × H × D)178 × 100 × 165 mm
Weight**2.5 kg
* Specifications and the design are subject to possible modification
without notice due to improvements.
** Dimensions and Weight shown are approximate.
•
• Above specifications comply with EIA standards.
• •
CONTENTS
Page Page
1 ABOUT LEAD FREE SOLDER (PbF)
2 FEATUERS
3 REPLACING THE FUSE
4 MAINTENANCE
5 LASER PRODUCTS
6 DIMENSIONS
7 WIRING CONNECTION
8 DISASSEMBLY INSTRUCTIONS
9 TERMINALS DESCRIPTION
10 PACKAGE AND IC BLOCK DIARAM
3
11 REPLACEMENT PARTS LIST 18
3
12 EXPLODE D VIEW (Unit)
13 DVD PLAYER PARTS LIST
3
3
14 EXPLODE D VIEW [DVD Deck]
3
15 WIRING DIAGRAM
16 SCHEMATIC DIAGRAM-1
4
5
17 SCHEMATIC DIAGRAM-2
6
18 BLOCK DIAGRAM
8
19 SCHEMATIC DIAGRAM for Printing with Letter Size
12
33
34
38
39
49
53
61
67
2
1 ABOUT LEAD FREE
SOLDER (PbF)
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a PbF
stamp on the PCB.
Caution :
•
• Pb free solder has a higher melting point than standard
• •
solder; Typically the melting point is 50 - 70°F (30 40°C) higher. Please use a soldering iron with
temperature control and adjust it to 700 ± 20°F (370 ±
10°C). In case of using high temperature soldering iron,
please be careful not to heat too long.
•
• Pb free solder will tend to splash when heated too high
• •
(about 1100°F/600°C)
•
• This lead free solder will be used for the products after
• Integration of the monitor, FM/AM radio, DVD Video, Video
• •
CD player and CD/MP3/WMA player
•
• Built-in AV Input/Output Terminals.
• •
•
• Built-in Dolby Digital decoder, DTS decoder.
• •
•
• Built-in DSP.
• •
•
• GUI (Graphic User Interface).
• •
•
• CS Auto (Circle Surround Automotive).
• •
•
• Touch Panel Operation.
• •
•
• DVD-R, DVD-RW, Playback.
• •
•
• ID code.
• •
•
• Differences Among 4 Models
• •
CQ-VD6505W
3 REPLACING THE FUSE
Use fuses of the same specified rating (15A). Using different
substitutes or fuses with higher ratings, or connecting the unit
directly without a fuse, could cause fire or damage to this unit.
4 MAINTENANCE
Your products is designed and manufactured to ensure a
minimum of maintenance. Use a soft cloth for routine exterior
cleaning. Never use benzine, thinner or other solvent.
5 LASER PRODUCTS
3
CQ-VD6505W
6 DIMENSIONS
4
7 WIRING CONNECTION
CQ-VD6505W
5
CQ-VD6505W
8 DISASSEMBLY INSTRUCTIONS
8.1. How to Remove the Flexible PCB(AP1)
6
8.2. How to Disassemble & assemble
CQ-VD6505W
7
CQ-VD6505W
9 TERMINALS DESCRIPTION
9.1. Main Block
IC601 : C2DBYY000231
Pin
No.
1 AVREF0Reference voltage for A/D
2 AVSSGround for A/D converter-0
3 ANT CNTAntenna controlO3.2
4 RCA SWVoice change of DVD-CH and
28 REMO DATAExt. remote control signalI5.0
29 CHC REM
30 I2C CLKI2C bus clockO5.1
31 I2C DATAI2C bus dataO5.1
32 OSD RESETOSD resetO3.2
33 EVSSGround for ext. unit-0
34 EVDD+3V power supply for ext. unit-3.2
35 DVD TX(MO)DVD deck TX dataO3.2
36 DVD RX(MI)DVD deck RX dataI3.2
37 BEEPBeep signalO0
38 AMP CNTExt. AMP controlO3.2
39 AMP STBExt. AMP stand-byO5.0
40 TFT SI(MI)TFT unit communication dataI0
41 TFT SO(MO)TFT unit communication dataO0.5
42 TFT CLKTFT unit communication clockO5.0
43 AMP MUTEInternal power AMP muteO0
44 SYS ONSystem power (5V) control for SW
45 NAVI REMO
46 ENTERENTER keyI3.3
47 FRONT MUTE Audio signal (BEEP NAVI) muteO5.0
48 VD COUNTVertical drive signal countI5.0
49 REAR MUTE Video out muteO5.0
50 SYSID1Connected equipment recognition
PortDescriptionI/OVol
converter
HUB. H: HUB L:VTR2
converter
Communication
voltage reg.
DET2
DET1
OUT
OUT
Changer data strobeI5.0
Changer clock / XM detection
signal
Changer remote control codeO5.1
PCB
NAVI remote control dataO0
(for HUB)
-3.2
O0
-3.2
O3.2
-2.5
I3.1
O0
I5.0
(V)
Pin
No.
51 SYSID2Connected equipment recognition
52 SYS MUTE
53 SYS MUTE
54 SYS MUTE
55 SYS
56 BATT SENSBattery level detectionI5.0
57 ACC SENSACC level detectionI5.0
58 PULSEMonitor position detection pulseI5.0
59 SYS PWRSystem power controlO5.0
60 MAIN PWRMain power controlO3.2
61 MONI PWRMonitor power controlO3.2
62 NAVI RM CHNAVI remote control output
63 SEC LEDLED blinking function for
64 EJECT LED
65 NAVI LEDNAVI LED on/offO0
66 MADrive mechanism control signalO3.2
67 MBDrive mechanism control signalO3.2
68 MCDrive mechanism control signalO3.2
69 BVSSGround for bus I/F-0
70 BVDDPower supply for bus I/F-3.2
71 FAN CNTFan motor power controlO3.2
72 ROTARY.1Rotary encoder signal (VOL
73 ROTARY.2Rotary encoder signal (VOL UP)I3.3
74 INIT DET 2Destination detectionI0
75 RADIO CNTRadio power controlO3.2
76 DVD MUTEDVD mute request / Flash
77 DSP SCKShift clock for DSP communication
78 DSP SDADSP communication dataO3.1
79 DSP RESETDSP resetO3.2
80 DVD CNTDVD deck power controlO3.2
81 DVD RESETReset signal for DVD deck control
82 FRAM HOLDF-RAM holdO0
83 FRAM CLKShift clock for F-RAM dataO0
84 FRAM DOF-RAM serial dataO0
85 FRAM CSF-RAM chip selectO3.2
86 FRAM WPF-RAM write protectO0
87 SW PWRSwitching power supply frequency
88 MODEMODE key detectionI3.2
89 JOY A/DADC input terminal for joy stic
90 NAVI DISPNAVI display activity detectionI3.3
91 NAVI SENSNAVI system connection detectionI3.3
92 SIDE BRAKE Side break detectionI3.3
93 INIT DETDestination detectionI0
94 POSI SENSADC input terminal for monitor
95 NAVI MUTENAVI muteI0
96 OFFSET DET Power IC abnormality detectionI0
97 AD KEYADC input terminal for AD key
98 REVERSEREVERSE signal detectionI3.3
99 FRAM DIF-RAM serial dataI0
100 V_NAVINAVI RGB signal changeO0
PortDescriptionI/OVol
I5.0
(for HUB)
System mute (FRONT)O5.0
(F)
System mute (SURROUND)O5.0
(S)
System mute (CENTER)O5.0
(C)
System mute (SW)O5.0
MUTE(SW)
O0
change
O3.2
CodeSecurity emphasis
No Connection--
(NC)
I0
DOWN)
I3.3
memory update cnt.
O2.8
data
O3.2
MPU
O0
change
I3.3
signal
I2.4
position signal
I3.3
signal
(V)
8
9.2. TFT Block
CQ-VD6505W
Pin
No.
1MONI CNTTFT monitor power supply
2BL CNTBacklight control outputO4.9
3TILT LED
4ASPECT LED
5EJECT LEDEJECT_LED controlO6NAVI LEDNAVI LED controlO7SRC LEDSOURCE button LED controlO8NCNC(GND connection)I0
17VSSGrand potential for in-0
18EVSSGrand potential for external-0
19VDDPositive power supply for in-4.9
20EVDDPositive power supply for
21SCLI2C bus clock output for DACO4.9
22SDAI2C bus data output for DACO4.9
23NCNC(OPEN)-24NCNC(OPEN)-25NCNC(OPEN)-26NCNC(OPEN)-27NCNC(OPEN)-28NCNC(OPEN)-29NCNC(OPEN)-30NCNC(OPEN)-31NCNC(OPEN)-32NCNC(OPEN)-33NCNC(OPEN)-34NCNC(OPEN)-35NCNC(OPEN)-36NCNC(OPEN)-37NCNC(OPEN)-38HD INHD signal inputI4.4
39VD INPAL N/PALM judgment VD
74NCNC(OPEN)-75NCNC(OPEN)-76NCNC(OPEN)-77NCNC(OPEN)-78NCNC(OPEN)-79NCNC(OPEN)-80BUS KILLFor connected confirmation of
PortDescriptionI/OVol
A/D converter
to - pole
to - pole
to + pole
to - pole
OPEN/CLOSE
the main CPU
COM
DATA
Serial communications data
input for the main CPU
Serial communications data
output for the main CPU
SW detection
self adjustment treatment
device
(V)
-4.9
I0
I1.2
I0
I1.2
I4.9
I4.9
I0.6
O0.4
O4.1
I0
9
CQ-VD6505W
9.3. DVD Servo Block
IC501 : C1AB00002402
Pin No.PortDescriptionsI/OVol
1VDDIOI/O pad power (3.3V)-3.3
2MD10SDRAM data busI/O0
3MD11SDRAM data busI/O0.6
4VDDCore power (1.8V)-1.8
5MD12SDRAM data busI/O0
6VSSIOI/O pad ground-0
7MD13SDRAM data busI/O0.7
8MD14SDRAM data busI/O0.5
9MD15SDRAM data busI/O0
10VDDIOI/O pad power (3.3V)-3.3
11/DQM1SDRAM data byte enableO0
12MA9SDRAM address busO0
13MA8SDRAM address busO0
14VSSIOI/O pad ground-0
15MA7SDRAM address busO2.3
16MA6SDRAM address busO1.9
17VSSCore ground-0
18MA5SDRAM address busO1.1
19VDDIOI/O pad power (3.3V)-3.3
20MA4SDRAM address busO2.0
21MA3SDRAM address busO2.3
22MCLKSDRAM clockO1.7
23VSSIOI/O pad ground-0
24CKESDRAM clock enableO3.3
25MA2SDRAM address busO2.3
26MA1SDRAM address busO1.0
27VDDIOI/O pad power (3.3V)-3.3
28MA0SDRAM address busO1.0
29MA10SDRAM address busO0
30MA11Not used-31VSSIOI/O pad ground-0
32MA12SDRAM address busO2.1
33MA13SDRAM address busO2.1
34VDDCore power (1.8V)-1.8
35/CS0SDRAM primary bank chip selectO2.7
36VDDIOI/O pad power (3.3V)-3.3
37/RASSDRAM command bitO3.1
38/CASSDRAM command bitO2.9
39/WESDRAM command bitO3.2
40VSSIOI/O pad ground-0
41/DQM0SDRAM data byte enableO0
42/DQM2SDRAM data byte enableO0
43MD16SDRAM data busI/O0.5
44VDDIOI/O pad power (3.3V)-3.3
45MD17SDRAM data busI/O0.5
46MD18SDRAM data busI/O0.5
47VSSCore ground-0
48MD19SDRAM data busI/O0.7
49VSSIOI/O pad ground-0
50MD20SDRAM data busI/O0
51MD21SDRAM data busI/O1.5
52MD22SDRAM data busI/O1.0
53VDDIOI/O pad power (3.3V)-3.3
54MD23SDRAM data busI/O0
55MD24SDRAM data busI/O0.5
56MD25SDRAM data busI/O0.5
57VSSIOI/O pad ground-0
58MD26SDRAM data busI/O0.5
59MD27SDRAM data busI/O0.8
60MD28SDRAM data busI/O0
61MD29SDRAM data busI/O1.0
62VDDIOI/O pad power (3.3V)-3.3
63MD30SDRAM data busI/O0.7
64MD31SDRAM data busI/O0.5
65/DQM3SDRAM data byte enableO0
66/CS1Not usedO67VSSIOI/O pad ground-0
68SPDIFS/PDIF digital audio outputO1.3
69VSSCore ground-0
(V)
Pin No.PortDescriptionsI/OVol
70AINDigital audio input for digital microI3.3
71AOUT3Serial audio data (Left/Right CH)O0
72AOUT2Serial audio data (Center/LFE CH)O0
73AOUT1Serial audio data (Sound Left/Right CH)O0
74AOUT0Serial audio data (Left/Right CH)O0
75VDDIOI/O pad power (3.3V)-3.3
76PCMCLKAudio DAC PCM sampling clockO1.8
77VDDCore power (1.8V)-1.8
78ACLKAudio interface serial data clockO1.7
79LRCLKLeft/Right channel clockO1.7
80/SRSTReset signalO3.3
81/RSTPPower on resetI3.3
82VSSIOI/O pad ground-0
83RXD1Not used-84SSPIN1SSP1 data in / UART1 16X clockI/O15
85VSSCore ground-0
86SSPOUT1SSP1 sata out / UART1 DTRI/O0
87SSPCLK1SSP1 clock / UART1 CTSI/O3.3
88SSPCLK0Not used-89VDDCore power (1.8V)-1.8
90SSIN0Not used-91VDDIOI/O pad power (3.3V)-3.3
92SSPOUT0Not used-93TXD0UART0 serial dataO3.2
94RXD0UART0 serial dataI3.0
95/CTS0Not used-96/RTS0Not used-97VSSIOI/O pad ground-0
98CXICrystal Oscillator terminalI1.6
99CXONot used-100OSCVSSOscillator ground-0
101OSCVDDOscillator power (1.8V)-1.8
102MVCLVDDMain/Video clock PLL power (3.3V)-3.3
103SCENNot used-104MVCKVSSMain/Video clock PLL Ground-0
105ACLKVSSAudio clock PLL ground-0
106SCMDNot used-107ACLKVDDAudio clock PLL power-3.3
108VDDDACDAC digital power (1.8V)-1.8
109VSSDACDAC digital ground-0
110CVBS2/CR/R Composite Cr/Component Cr/SCART
111IOMCascaded DAC differential outputO1.0
112C/CB/BChrominance/Component Cb/SCART CbO0.7
113VAA3DAC analog power (3.3V)-3.3
114Y/GLuminance/SCART GO0.4
115VSSADAC analog ground-0
116VREFNot used-117VAA--1.8
118CVBS/CComposite/S-Video ChrominanceO0.5
119RSETCurrent setting resistor connectionO1.4
120COMPCompensation capacitor connectionO2.0
121VSSCore ground-0
122VCLKNot used-123VSYNCNot used-124HSYNCNot used-125VDDIOI/O pad power (3.3V)-3.4
126-131 VI07-02Not used--
132VSSIOI/O pad ground-0
133Not used-134Not used-135VDDCore power (1.8V)-1.9
136-139 AD31-28Not used--
140VDDIOI/O pad power (3.3V)-3.4
141-144 AD27-24Not used--
145/PWE3Not used-146AD23Not used-147VSSIOI/O pad ground-0
158
159VDDCore power (1.8V)-1.9
160SCLKExternal bus clockO2.1
161ACKProgrammable WAIT/ACK/RDY controlI3.4
162VSSIOI/O pad ground-0
163-168 AD13-08Address/Data busI/O0
169VDDIOI/O pad power (3.3V)-3.4
170/PWE1Not used-171VSSCore ground-0
172-176 AD7-3Address/Data busI/O0
177VSSIOI/O pad ground-0
178-180 AD02-00Address/Data busI/O0
181VDDIOI/O pad power (3.3V)-3.4
182/PWE0Byte write enableO0
183ALEAddress latch enableO0
184-187 LA0-3Latch addressO3.3
188VSSIOI/O pad ground-0
189RDRead signalO3.4
190LHLDANot used-191LHLDNot used-192VDDCore power (1.8V)-1.9
193/PCS0Peripheral chip select 0O3.4
194XI01Not used-195DACCS2DAC output select 2O3.4
196VDDIOI/O pad power (3.3V)-3.4
197DACCS1DAC output select 1O3.4
198NINTCPPMNot used-199CPPMCSNot used-200XI06Not used-201VSSCore ground-0
202FRAMCSFRAM chip selectionO0
203DACRSTDAC resetO0
204VSSIOI/O pad ground-0
205FEPCSFront End Pro. LSI chip selectO3.4
206FEPRSTFront End Pro. resetO3.4
207SODCCSSODC LSI chip selectionO3.4
208NINTHOSTHOST interruptI3.4
209NINTDDCDDC interruptI3.2
210VDDIOI/O pad power (3.3V)-3.4
211NINTDSCDSC interruptI3.5
212VDDCore power (1.8V)-1.9
213DSYNVDVD parallel mode sector SYNCI3.4
214DREQDVD parallel mode data requestO3.4
215DCLKData sampling clockI3.4
216DSTBParallel mode data valid/Serial mode
217DVD0DVD drive parallel data portI0
218VSSIOI/O pad ground-0
219DVD1DVD drive parallel data portI0
220DVD2DVD drive parallel data portI0
221DVD3DVD drive parallel data portI3.4
222DVD4DVD drive parallel data portI0.8
223DVD5DVD drive parallel data portI0.8
224VDDIOI/O pad power (3.3V)-3.4
225DVD6DVD drive parallel data portI3.4
226DVD7DVD drive parallel data portI3.4
227MD0SDRAM data busI/O0.5
228VSSIOI/O pad ground-0
229MD1SDRAM data busI/O0
230VSSCore ground-0
231MD2SDRAM data busI/O0.8
232MD3SDRAM data busI/O0.8
233VDDIOI/O pad power (3.3V)-3.3
234MD4SDRAM data busI/O3.3
235MD5SDRAM data busI/O0
236MD6SDRAM data busI/O0.8
237VSSIOI/O pad ground-0
238MD7SDRAM data busI/O0
239MD8SDRAM data busI/O0
240MD9SDRAM data busI/O0
clock
(V)
I0.7
CQ-VD6505W
11
CQ-VD6505W
10 PACKAGE AND IC BLOCK DIARAM
10.1. Main Block
IC151 : C0JBAA000115
IC203, IC301, IC302 : C0ABBB000105
IC608 : C0JBAB000255
IC200 : C1ZAZ0001450
IC303 : C0ZBZ0000770
IC610 :
C0JBAZ001166
IC611 : C0JBAZ002192
12
IC612 : C0FBBD000065
CQ-VD6505W
IC754 : C0DBAMG00015
13
CQ-VD6505W
10.2. Sub Block
IC101 : C0ABBB000090
IC602 : C3GBCY000001
IC710 : C0CBCYG00004
IC711 : C0GBG0000032
IC102 : C0JBAA000102
IC252 : C0ABBB000105
IC751 : AN8065S-E1V
IC253 : C0JBAS000081
IC351 : C1AB00001604
14
IC752, IC753, IC755 : C0DBEKG00001
10.3. TFT/SW-R/SW-L Block
CQ-VD6505W
IC352 : C1AB00000164
IC1 : B3MBZ0000006
IC402 : C0FBBD000065
IC403,405-408 : C0JBAA000115
IC502 : C0DBAZC00010
IC501 : C0DBAZA00017
IC503 : C0CBAAF00009
IC504 : C0DBEKG00001
15
CQ-VD6505W
IC805 : C1AB00001604
10.4. DVD Deck Block
IC806 : C1ABBB000069
IC101 : AN8703FH-V
IC311 : C0GBY0000012
IC271 : C0JBAA000372
16
IC275, IC561 : C0JBAZ001014
CQ-VD6505W
IC631, IC641 : C0JBAH000082
IC321 : C0GBH0000006
IC411 : C0CBADC00084
IC651 : C3GBCA000001
IC652 : C0JBAB000255
IC441 : MN13821JP
17
CQ-VD6505W
11 REPLACEMENT PARTS
LIST
Notes :
1. Be sure to make your orders of replacement parts
according to this list.
2. Important safety notice: Components, identified by
have special characteristics important for safety. When
replacinganyofthesecomponents,useonly
manufacturer´s specified parts.
3. Location keys in the remarks column indicates the general
location of the parts shown in the exploded drawing, as in a
road map.
4. The marking (RTL) indicates that Retention Time is limited
for this item. After the discontinuation of assembly in
production, the item will continue to be available for a
specific period of time. The retention period of availability is
dependent on the type of assembly, and in accordance with
the laws governing part and product retention. After the end
of this period, the assembly will no longer be available.
•
• Order intake period is basically six months after the first
• •
shipment.
5. “T” marks in remarks colum are indicated supply parts of
PTW.