Panasonic CFS9KWBZZDM Reference Manual

Reference Manual

Personal Computer

Model No. CF-C1 Series

CF-F9 Series

We recommend that this Reference Manual be printed.

Read Me First

Illustrations and Terminology in this Reference Manual

NOTE NOTE provides a useful fact or helpful information. CAUTION CAUTION indicates a condition that may result in minor or moderate injury.

Enter Fn+F5

Windows 7

(Start) - [All Programs]

Windows XP

[start] - [Run]

 or ⇒ These symbols indicate related pages.

xxxx

This illustration means to press the This illustration means to press and hold the Fn key, then press the F5 key.

When using with the key and the

This illustration means to click (Start), then to click [All Programs].

This illustration means to click [start], then to click [Run].

 : If this is clicked, it will jump to the page corresponding Reference Manual.

⇒ : Refer to the Operating Instructions.

If *1 is clicked, it will jump to a related topic.

Ctrl

key and the

key reversed.

Enter

key.

Ctrl

key functions interchanged, read with the Fn

 “Genuine Windows® 7 Professional” is indicated as “Windows” or “Windows 7”.

 In this manual, “Genuine Microsoft

Tablet PC Edition Service Pack 3” are indicated as “Windows” or “Windows XP” unless otherwise indicated.

 <Only for CF-C1 Series>

The computer screen supporting two touching methods (using digitizer pen / your fingers) is referred to simply as the “screen”.

 <Only for CF-F9 Series>

The following software package is described as follows:

• "WinDVD™ 8 (OEM Version)" as "WinDVD"

 This manual explains using the Windows XP and Windows 7 default setting.  Some illustrations are simplified to help your understanding and may look different from the actual unit.

Windows 7

Windows® XP Professional Service Pack 3” and “Genuine Microsoft® Windows® XP

Sound and Video

 Sound (e.g. MP3, WMA) and video (e.g. MPG, WMV) recorded in PC Cards and SD Memory Cards may be interrupted

during playback. If this happens, copy them to the hard disk drive and play back.

Read Me First

 Sound and video in AVI files may be interrupted or produce a time-lag during playback. If this happens, Click or

on the notification area. Select [High performance]. This may remedy the problem.

 Depending on the processing status on Windows, sound may be interrupted at Windows startup. You can mute the sound

at startup.

A Right-click the desktop and click [Personalize] - [Sounds]. B Remove the check mark from [Play Windows Startup sound], and click [OK].

Windows 7

Entering hibernation suddenly

The computer may enter the hibernation mode by thermal control if you use the computer in a high ambient temperature and use an application that uses a lot of CPU power. Wait a few minutes (at least 5) before turning the computer on again if this occurs.

Using the Touch Pad

In this section, illustrations of the CF-C1 Series are used as examples. Use the Touch Pad to move the cursor on the screen and perform computer operations.

A. Work Surface (Touch Pad) B. Left Button C. Right Button

Function Operation

Moving the Cursor

Move the tip of your finger lightly over the work surface.

Tapping/Clicking

Double-Tapping/ Double-Clicking

tapping or clicking To right-click: Can only be performed by clicking the right button.

double-tapping or double-clicking

Using the Touch Pad

Function Operation

Dragging

Two quick taps, but on the second tap leaving your finger down (applying pressure) and moving it on the work surface. or While holding down the button, moving your finger on the work surface.

Scroll Trace a circle around the Touch Pad. ( below)

NOTE

 You can change the speed of the double-click or the operations of mouse buttons by clicking (Start) -

[Control Panel] - [Hardware and Sound] - [Mouse]/ [start] - [Control Panel] - [Printer and Other Hardware] [Mouse].

Windows XP

Windows 7

Scroll

 The Touch Pad utility (below)

You can scroll continuously by tracing a circle on the Touch Pad (Start scrolling from the edge of the Touch Pad).

Vertical scroll It can be used in the default setting. Horizontal scroll A setting is required to use the horizontal scroll.

Windows XP

 The Virtual Scrolling function ( page 9)

You can scroll vertically (or horizontally) by tracing repeatedly in the desired direction.

Vertical scroll The Virtual Scrolling function must be set to enable. Horizontal scroll

You can use separate settings for each account regarding whether to use the Touch Pad utility or the Virtual Scrolling function.

Using the Touch Pad

Using the Touch Pad Utility

You can scroll easily by tracing a circle on the Touch Pad.

NOTE

 External mouse drivers cannot be used at the same time as the Touch Pad utility.

1 Make the following settings to use the horizontal scroll.

Once the settings have been made, it is not necessary to make the same settings the next time.

Windows 7

A Click on the notification area and click .

Windows XP

B click [Settings].

When is not displayed: Click (Start)/ [start] - [All Programs] - [Panasonic] - [Touch Pad Utility settings].

If a message appears indicating that the Touch Pad utility is not running, click

Windows 7

Pad Utility], and display .

C Add a check mark for [Activate horizontal scroll function] in the [General

settings] screen, and click [OK].

Click on the notification area.

Windows 7

(Start)/ [start] - [All Programs] - [Panasonic] - [Touch

Windows XP

2 Place the cursor over the area that you want to scroll, and tap

(click).

Using the Touch Pad

3 Remove your finger from the pad, then place your finger in the appropriate area to begin

scrolling.

The finger position on the Touch Pad can be changed using the Touch Pad utility. ( page 8) This explanation assumes in the default setting.

Vertical scroll

Position where finger is placed

Icon on the notification area When you place your finger on the Touch Pad, the icon changes.

If the horizontal scroll function has not been enabled, the segment shown in the figure above (A) is also included in the area to begin vertical scrolling.

Horizontal scroll

4 Trace a circle around the Touch Pad without lifting your finger from the pad.

The scroll direction can be changed using [Reverse vertical scrolling] or [Reverse horizontal scrolling] in the Touch Pad utility. (below)

Vertical scroll

Trace clockwise To scroll down To scroll right

Horizontal scroll

Using the Touch Pad

Vertical scroll

Trace counter-clockwise To scroll up To scroll left

When the horizontal scroll function has not been enabled, any scrolling will be vertical scrolling.

 The screen will not scroll if you trace toward the center of the Touch Pad.  On screens that cannot be scrolled (e.g., desktop screen), if you scroll, the computer may try to scroll the screen,

causing the cursor to freeze. If this happens, remove your finger from the Touch Pad and begin again, this time starting from the center of the Touch Pad.

 For example, on a screen that will only scroll horizontally, even if you execute a vertical scroll, the screen will

scroll horizontally.

Horizontal scroll

5 Once scrolling has begun, continue to trace a circle on the Touch Pad without removing

your finger from the pad.

 As long as you are tracing a circle, you can continue scrolling using any position on the Touch Pad.  To scroll in the opposite direction, trace a circle in the opposite direction without removing your finger from the

Touch Pad.

6 When you finish scrolling, remove your finger from the Touch Pad.

 Change the settings for the Touch Pad utility

1 Click on the notification area and click .

Windows 7

Windows XP

Click on the notification area.

2 Click [Settings].

When is not displayed: page 6, step1-B

3 Change the settings.

Using the Touch Pad

4 Click [OK].

Windows XP

Using the Virtual Scrolling Function

Set the Virtual Scrolling function using the following procedure. The Touch Pad utility will be disabled.

1 Click on the notification area.

2 Click [Settings].

When is not displayed: page 6, step 1-B

3 Remove the check mark from [Activate Touch Pad function] in [General settings], and

then click [OK].

Click [start] - [Control Panel] - [Printers and Other Hardware] - [Mouse] - [Device Settings].

5 Click the device name (e.g., Synaptics TouchPad) in [Devices], then click [Settings]. 6 Click [Virtual Scrolling], add a check mark for the scroll functions you want to use, then

click [OK].

7 Click [OK] at [Mouse Properties].

NOTE

 Because the Touch Pad utility and the Virtual Scrolling function both offer scrolling

functions that use the Touch Pad, these two features cannot be used simultaneously. If you try to use them at the same time, a message may be displayed asking you if you want to enable the Touch Pad utility.

• To use the Touch Pad utility: Click [Yes]. The Virtual Scrolling function will be disabled.

• To use the Virtual Scrolling function: Click [No].

You can uninstall the Touch Pad utility using the following procedure.

A Click or on the notification area. B Click [Exit].

C Click [start] - [Control Panel] - [Add or Remove Programs] - [Touch Pad Utility], and then click [Uninstall] to remove

the program.

Using the Touch Pad

Handling the Touch Pad

 By design, the Touch Pad is to be used with a fingertip only. Do not place any object on the work surface or press down

forcefully with sharp-pointed objects (e.g., nails) or hard objects that can leave marks (e.g., pencils and ball point pens).

 Try to avoid having any harmful substances, such as oil, come in contact with the Touch Pad. The cursor may not work

properly in such cases.

 When the Touch Pad becomes dirty:

Wipe to remove dirt by using a dry soft cloth such as gauze or a soft cloth first applied with detergent diluted with water and then thoroughly wrung. Do not use benzene or thinner, or rubbing alcohol. Doing so may adversely affect the surface, e.g., discoloration. In addition, do not use commercially available household cleaners and cosmetics, as they may contain components harmful to the surface.

Digitizer / Multi Touch Operation

<Only for CF-C1 Series> The screen of your computer allows you to perform the same operations as the Touch Pad or mouse by touching its surface. The computer supports two touching methods, using the digitizer pen (included), and using your fingers. The operation settings can be changed. ( page 14)

Operation by Touching the Screen

 Touching with the digitizer pen

Functions Operation

Moving the cursor

The cursor is moved to the location pointed by the digitizer pen.

Clicking (Tapping)

One tap

Double-clicking (Double-tapping)

Two quick taps

Digitizer / Multi Touch Operation

Functions Operation

Dragging

 To right-click

 You can choose either of the two ways below.

 Touch and hold with the digitizer pen.  Press and hold the button (A) of the digitizer pen, and then touch the object.

Windows 7

• To Display the mouse image

Touch and hold the object (i.e. file or icon), move the digitizer pen on the surface (dragging the object to the desired location), then release the digitizer pen.

Windows XP

A Click B Click [Touch], and add a check mark for [Show the touch pointer when I’m interacting with items on the screen].

A Touch the item you want to right-click and continue touching until is completely displayed.

B Move the digitizer pen away from the surface of the display.

 When needed, the above settings can be configured using the following procedure.

A Click [start] - [Control Panel] - [Printers and Other Hardware] - [Tablet and Pen Settings] - [Pen Options]. B Click [Press and hold] in [Pen Action] and then click [Settings]. C In [Press and Hold Settings], change the settings and then click [OK].

For more information, refer to “Help” in the bottom right corner of the [Press and Hold Settings].

(Start) - [Control Panel] - [Hardware and Sound] - [Pen and Touch].

Moving the digitizer pen away from the surface of the display before has not completely displayed will result in a left click.

Digitizer / Multi Touch Operation

 Touching with your fingers

Functions Operation

Moving the cursor

Clicking (Tapping)

Double-clicking (Double-tapping)

The cursor is moved to the location pointed with finger.

One tap with one finger

Two quick taps with one finger

Dragging

Touch and hold the object (i.e. file or icon), move the finger on the surface (dragging the object to the desired location), then release the finger.

Digitizer / Multi Touch Operation

The following operations may not be possible depending on the application program being used.

Functions Operation

Zoom in, zoom out Use two fingers to touch the image or text you want to zoom in or out on, and draw

your fingers apart to zoom in and together to zoom out.

Rotate Use two fingers to touch the image or text, and use one finger as the center of

rotation and the other finger to rotate.

Windows 7

 Change the settings for the screen

 When needed, the screen settings can be configured using the following procedure.

A To Display [Pen and Touch] screen.

Click on the notification area and click . And then click [Customize your flicks settings].

When is not displayed: Click (Start) - [Control Panel] - [Hardware and Sound] - [Pen and Touch],

and add the check mark in [Display flicks icon in the notification area] in [Flicks].

B Make necessary changes and click [OK].

CAUTION

 If a change is made to the display resolution, or the cursor cannot be pointed correctly with the digitizer pen, be sure to

calibrate the screen. ( page 15)

 When mouse drivers are installed (e.g., IntelliMouse), the screen function may not be used.  When the operation of panning (only the internal LCD) is performed while the display resolution is set higher than the

resolution of the internal LCD, the screen function will not work properly.



Even when only an external display is in use, the cursor will move on the external display if the surface of the internal LCD is touched when the screen driver is active. Therefore, do not touch the internal LCD when only an external display is in use.

 The screen function does not work in the Setup Utility.

Windows XP

 The screen function does not work in the “Full Screen” of [Command Prompt].

Digitizer / Multi Touch Operation

NOTE

 Do not move the digitizer pen too quickly. If the digitizer pen moves too quickly, the cursor may be unable to follow its

movement.

Calibrating the Screen

When you cannot point correctly with the digitizer pen (included) or your fingers, calibrate the screen by following the steps below. A standard user needs to perform the calibration as an administrator before performing the calibration for each user.

Windows 7

 Calibration by an administrator

NOTE

 At first, log on to Windows as an administrator, and perform this calibration.  Rotate the display to primary landscape before performing the calibration. ( page 21).

1 Run [Tablet PC Settings].

Click (start) - [Control Panel] - [Hardware and Sound] - [Tablet PC Settings].

2 Click [Calibrate].

3 Click [Pen input] or [Touch input].

To calibrate the screen for the digitizer pen operation, click [Pen input]. To calibrate the screen for the finger operation, click [Touch input].

4 If [User Account Control] is displayed, click [Yes].

5 Using the digitizer pen or finger, touch each of the “+” target marks one by one, and then

click [OK].

Digitizer / Multi Touch Operation

 Calibration by a standard user

NOTE

 Perform the following calibration for each user.

1 Run [Tablet PC Settings].

Click (start) - [Control Panel] - [Hardware and Sound] - [Tablet PC Settings].

2 Click [Calibrate]. 3 Click [Pen input] or [Touch input].

To calibrate the screen for the digitizer pen operation, click [Pen input]. To calibrate the screen for the finger operation, click [Touch input].

4 Using the digitizer pen or finger, touch each of the “+” target marks one by one, and then

click [OK].

Windows XP

 Calibration by a standard user

NOTE

 Perform the following calibration for each user.

1 Click [start] - [Control Panel] - [Printers and Other Hardware] - [Tablet and Pen Settings].

2 Click [Calibrate…].

3 Click [Pen] or [Touch].

To calibrate the screen for the digitizer pen operation, click [Pen]. To calibrate the screen for the finger operation, click [Touch].

4 Using the digitizer pen or finger, touch each of the “+” target marks one by one.

5 Click [OK] for the digitizer pen operation, or [Finished] for the finger operation.

Digitizer / Multi Touch Operation

Handling the Screen

 Use the digitizer pen included with the computer. Do not use pencils, implements with sharp tips or hard objects for screen

operations. The screen may be damaged as a result.

 Do not place any object on the surface or press down forcefully with sharp-pointed objects (e.g., nails), or hard objects that

can leave marks (e.g., pencils and ball point pens).

 Do not apply pressure to the perimeter of the display panel. The cursor may move to the edge of the display.  Do not operate the computer when such things as dust are on the screen. Do not allow contact with substances that could

dirty the screen, such as oil.

 Do not apply too much pressure when operating the screen.

Only a light touch is required to operate the screen. Applying too much pressure may damage the surface.

 Do not touch the screen outside of the LCD display area.

The screen input area is defined by the LCD display screen. Touching the screen outside of the display area may result malfunctions or damage to the screen.

 When the screen becomes dirty:

• Wipe to remove dirt by using a dry soft cloth included with the computer.

• Do not use benzene or thinner, or rubbing alcohol.

• For more information, refer to “Suggestions About Cleaning the LCD Surface” ( page 18).

Handling the Digitizer Pen

 Clean the digitizer pen tip and screen prior to operation. Foreign particles can scratch the screen and impede the

operation of the digitizer pen.

 Use the digitizer pen only for the computer screen. Using it for any other purpose may damage the digitizer pen and

scratch the screen.

Digitizer / Multi Touch Operation

Suggestions About Cleaning the LCD Surface

To improve the outdoor visibility of the display, a low reflection coating has been added. In order to avoid scratches and peeling of this coating, an approved soft cloth has been included to wipe the LCD surface of the computer. Before using the computer, be sure to read the instructions provided below.

• Be sure to wipe the LCD display to remove fingerprints, etc., with the soft cloth.

• Do not wipe areas other than the LCD display with the soft cloth.

 Use the soft cloth when it is dry. Do not apply water or solvents to the soft cloth.  First, lightly wipe foreign particles and dust adhering to the LCD display on one side of the soft

cloth. Do not use force, since the LCD surface may be damaged with the foreign particles or dust. Next, wipe off fingerprints, etc., with the other side of the soft cloth. After wiping off foreign particles and dust, wash the soft cloth (refer to the following) to remove the foreign particles and dust from the soft cloth.

 When the soft cloth becomes dirty, wash it with neutral detergent. Do not use bleach or a fabric

conditioner (softener), or carry out sterilization by boiling.

 If the LCD gets wet, wipe the surface lightly with the soft cloth.  We recommend wiping the LCD display before using the computer.

Tablet Buttons

Button Function

LCD Brightness

: down : up

Input Panel

Tablet PC Input Panel on/off  This button does not work on the Welcome screen.

Rotation

Rotates the display. ( page 21)  Do not press the button again until the display rotation is completed.

Security

Ctrl

Alt

Del

Works as

USER

Dashboard for CF-C1 on/off ( page 33)

NOTE

 The Tablet buttons work when the Windows screen is displayed.  The Tablet buttons may not work immediately after Windows is started up or the Windows logon screen (or the

Welcome screen) is displayed.

Setting the Tablet Buttons

NOTE

 You can have different settings for each user.  On the Windows logon screen and Welcome screen, the tablet buttons are enabled and work in default irrespective of

the settings you made.

 To change the tablet button functions

You can change the functions of the following tablet buttons.

(LCD Brightness) / (Input Panel) / (Rotation) / (USER)

Tablet Buttons

To change the functions of the LCD Brightness buttons

1 Open the Dashboard for CF-C1.

Press (USER) button.

2 Select a function in [Brightness buttons].

Brightness Up/Down: Use the buttons to adjust the LCD brightness (default setting) Page Up/Down: Use the buttons to control page up/down Up/Down Arrow keys: Use the buttons to move the cursor up/down

3 Close the Dashboard for CF-C1.

To change the functions of the Input Panel/Rotation/USER buttons

1 Open the Dashboard for CF-C1.

Press (USER) button.

2 Click [Change settings] in [Tablet buttons].

Windows 7

The [Tablet PC Settings] / [Tablet and Pen Settings] screen appears.

Windows XP

3 Select the button for which you want to change the function under [Tablet button]. 4 Click [Change…].

Windows 7

The [Tablet Button Actions] / [Change Tablet Button Actions] screen appears.

5 Select a function in [Press:] / [Action:].

If you want to use the selected button to start an application program, select [Start a program] /

Windows XP

If you select [(none)], the selected button will not function when pressed.

[Launch an application], click [Browse…] and select the program to be started.

Windows 7

Windows XP

Windows 7

6 Click [OK], and then [OK].

Display Rotation

<Only for CF-C1 Series> After Windows is started up, you can rotate the display and perform the Touch Pad and screen operations in the rotated mode.

Rotating the Display

1 Press (Rotation) button ( page 19).

 To select the angle and rotate the display

When using the computer in the tablet mode

 Press (Rotation) button. When the computer is held in an upright position, the display will automatically rotate to the most suitable orientation.

If the display has already been at the most suitable orientation, the display will not rotate. When the computer is held in a level position, the display will rotate 90 degrees clockwise at each press.

Windows 7

 Press and hold (Rotation) button. The display will continue rotating 90 degrees clockwise.

When using the computer in the laptop mode

 Press (Rotation) button. When the rotation angle is changed from the default value, the display will rotate by the set angle.

When the rotation angle is not changed, the display will rotate to [Primary Landscape].

Windows 7

 Press and hold (Rotation) button. The display will continue rotating 90 degrees clockwise.

NOTE

 Be sure to use the above procedures to rotate the display.

Display Rotation

Changing the Settings

By using the Display Rotation Tool, you can change the settings of the display rotation.

1 Click on the notification area and right-click .

Windows 7

Windows XP

Right-click on the notification area.

2 Click [Setting...].

3 Change the settings.

A. Changing the angle in the laptop mode

(Default: Keep Angle)

B. Changing the angle in the tablet mode

(Default: Keep Angle)

C. Activating/deactivating the confirmation message that allows you to

select whether to turn off wireless WAN when the antenna is placed close to the user.

• Depending on the model, this item does not appear.

4 Click [OK].

Display Rotation

NOTE

 If you shut down Windows when you rotate the display, the Touch Pad and screen do not match the display angle next

time you start up Windows for a few seconds.

 The Touch Pad and the screen may not match the display angle if you change display properties or Intel(R) Graphics

Media control panel when you rotate the display. ( page 155)

 When some applications are running, the display may not be rotated and the operation of the Touch Pad and the

screen may not match the display angle.

 The computer’s performance will decrease somewhat.  While the display is rotated:

• Do not use the Extended Desktop (The Touch Pad or screen may fail to operate properly).

• Do not calibrate the screen.

• Do not set the display resolution larger than the resolution of the internal LCD.

 If motion video is played while the display is rotated, the picture may not be displayed properly or the sound may be

broken up. This problem can be corrected by rotating the display to primary landscape.

 The Touch Pad scroll function does not work while the display is rotated.

Windows 7



If the display is rotated when the resolution is set to 800 x 600 pixels, depending on the Windows specifications, incorrect values may be shown for the resolution displayed in [Resolution] of [Display Settings]. Continue using these settings, without changing [Resolution].

 The display cannot be rotated in the Setup Utility.

Windows XP



The display cannot be rotated in the "Full Screen" of [Command Prompt].

 The display rotation angle may differ before and after Logging on.

Key Combinations

NOTE

 Do not repeatedly press the keys in quick succession.  Do not use the key combinations together with Touch Pad (external mouse), screen or other key operations.  Do not use the key combinations before you log on to Windows. Wait until the hard disk drive indicator turns off.

On the Setup Utility screen, you can use the key combinations of combinations of

 The key combinations may not work with some applications.  The pop-up icon appears after logging on to Windows. It may not appear in some application conditions (e.g., when

[Command Prompt] is set to “Full Screen”).

Key Functions Pop-up Icon

Fn+F1

Fn+F2

+ F3, the display is switched between the internal LCD and the external display.

LCD brightness (

Fn+F1

You can select a different brightness level setting for when the AC adaptor is connected and for when it is not connected. (In the default setting, the LCD brightness is set to be darker when the AC adaptor is not connected.)

= down / Fn+F2= up)

NOTE

+ F1, Fn + F2 and Fn + F3. By using the key

 Alternatively, you can push (LCD Brightness) buttons.  The brightness of the power indicator changes in keeping with the brightness

level of the internal LCD.

Key Combinations

Key Functions Pop-up Icon

Fn+F3

Display switching ( page 98)

Windows 7

When an external display is connected you can change the operating mode. (The change you made may not be effective until the operating mode by pressing + Computer only Duplicate Extend Projector only

Enter

is pressed.) You can also change

• After pressing + right cursor keys.

Windows XP

(When an external display is connected) Internal LCD Simultaneous display External display

NOTE

 When an external display is connected to an optional port replicator ( page

97), the display switching may work differently from the above. For further

information, refer to the Operating Instructions of the mini port replicator.

 When an external display is connected, refer to the External Display ( page

98).

CAUTION

 Do not press any keys until the display has finished switching.  Do not use this function:

• When an external display is not connected.

• When playing motion video such as DVD or MPEG.

• When using the Extended Desktop.

 Until Windows startup is completed (during Setup Utility, etc.), the

simultaneous display cannot be used and pressing display between the internal LCD and the external display.

, you can select the operating mode by using the left and

+ F3 switches the

Key Combinations

Key Functions Pop-up Icon

Fn+F4

Speaker on/off

NOTE

 Beeps do not sound if you turn off the speaker sound.

OFF (MUTE)

Fn+F5

Fn+F6

Fn+F7

Fn+F9

Fn+F10 Fn+NumLk

Fn+Home

Fn+

Fn+

Volu m e

(

+ F5= down / Fn + F6= up)

NOTE

 When fine-tuning the sound volume, press and hold

intermittently.

Activate sleep / standby ( page 62)

Remaining battery power  page 38 Activate hibernation ( page 62) __

Run the ScrLk (Scroll Lock) function

The functions differ depending on the application software.

Lead to the last page or move the cursor to the end of the current line (End) __

Move the back page (PgUp) __

Move the next page (PgDn) __

Windows 7

Windows XP

, and press F5 or F6

Key Combinations

Hotkey Settings

You can make two settings:

• Fn key lock

When you press combinations.

• Pop-up icon on/off

1 Start up the Hotkey Settings.

Click (Start)/ [start] - [All Programs] - [Panasonic] - [Hotkey Settings].

2 Make the settings.

[Use Fn key lock]

 When using an

A Press B Press another key. (Lock released)

 When using successive

A Press B Press another key.

Fn key remains locked until you press

Windows 7

once. (Locked)

twice. (Locked)

, the key is locked (pressed-down) until you press another key. Use this when pressing difficult key

Windows XP

key combination

key combinations

again.

[Notification]

[Make sounds when Fn key is pressed] [Show status on screen]: Displays the Fn key status on the notification area.

•:

[Disable popup]

The Pop-up icon will not be displayed.

is locked.

is not locked.

3 Click [OK].

NOTE

 You can have different settings for each user.

If the speakers are muted, beeps do not sound.

Software Keyboard

<Only for CF-C1 Series> You can use the Software Keyboard instead of the on-screen keyboard of Tablet PC Input Panel. By using the Software Keyboard, you can change the size of the Software Keyboard, and can use the numeric keypad.

NOTE

 You cannot uninstall Tablet PC Input Panel. When you enter text, select either the Software Keyboard or Tablet PC

Input Panel.

Starting the Software Keyboard

1 Click / on the notification area.

Alternatively, you can click (Start) / [start] - [All Programs] - [Panasonic] - [Software Keyboard].

Windows 7

Windows XP

Windows 7

Windows XP

2 Touch the software keyboard.

 To use shortcut key

Example : Press

 If you added the input language, the language bar (e.g. ) is displayed on the notification area. To select the

keyboard language, use the language bar on the notification area. If the keyboard language does not change, click the title bar of the software keyboard and then click on the application.

A. Software keyboard menu ( page 29) B. Moves the software keyboard to a corner of the screen. C. Works as the

D. Tapping : Works as shortcut key. ( +

Double-clicking : Works as the key.

E. Works as a right-click. (Same function as the key) F. Changes the size of the Software Keyboard, and can use the numeric keypad.

NOTE

 You cannot use

Windows XP

 You cannot use the software keyboard in the "Full Screen" of [Command Prompt].  You can set a different language to each application ( Windows help), and the keyboard layout switches according

to the application.

 Depending in the language, some keys are displayed in orange. You can use them to input characters such as ë and

ö.

Ctrl

+ C

Ctrl

(turns blue) and then press C.

key. (Available function is displayed.)

Ctrl

Alt

Del

on the software after logging on.

etc.)

Software Keyboard

Software Keyboard Menu

1 Click (A).

2 Add a check mark to the function you want to use.

 [Auto Move]

The software keyboard moves automatically to avoid overlapping the selected window.

 [Auto Restore]

The software keyboard minimized on the notification area will be restored when you change the input mode. This may not work on some applications.

 [Always On Top]

The software keyboard appears on the top.

 [Transparent]

The software keyboard appears semi-transparent.

 [Big Size]/[Medium Size]/[Small Size]

Select the size of the software keyboard.

 [Ten key (Big)]/[Ten key (Medium)]/[Ten key (Small)]

Select the size of the numeric keypad.

 [Change Size Automatically (Big Medium)]

The size changes according to the angle of the screen display.

NOTE

 You can change the currency symbol (B) of the numeric keypad.

Windows 7

and Language] - [Formats] - [Additional settings] - [Currency] - [Currency symbol].

Windows XP

- [Regional and Language Options] - [Regional Options] - [Customize] - [Currency] [Currency symbol]

 After changing the currency symbol, click (A), and then change the size of the

numeric keypad so that the selected currency symbol is shown.

 You can input the unit by using (C).

Click (Start) - [Control Panel] - [Clock, Language, and Region] - [Regional

Click [start] - [Control Panel] - [Date, Time, Language and Regional Options]

Software Keyboard

Starting the Software Keyboard Using the Tablet Button

To start the Software Keyboard using the tablet button, proceed as follows.

1 Open the Dashboard for CF-C1.

Press (USER) button.

2 Click [Change settings] in [Tablet buttons].

Windows 7

The [Tablet PC Settings] / [Tablet and Pen Settings] screen appears.

3 Select [Input Panel] under [Tablet button].

4 Click [Change…].

Windows 7

The [Tablet Button Actions] / [Change Tablet Button Actions] screen appears.

Windows XP

5 Select a function in [Press:] / [Action:].

6 Select [Start a program] / [Launch an application].

Windows 7

Windows XP

7 Click [Browse…], and input the following.

Windows 7

c:\Program Files\Panasonic\MEISKB\Skblnch.exe

Windows XP

c:\Program Files\Panasonic\MEISKB\MEISKB.exe

8 Click [OK], and then [OK].

+ 163 hidden pages