Panasonic CF71KYCGCAM Operating Instruction Supplement Windows 98
Personal Computer
Supplementary Instructions for Windows® 98
CF-71 Series
This manual contains supplementary instructions regarding the use of the computer. It explains the cases
where the operation of the computer differs from that in the Operating Instructions.
Replace Windows 95 for Windows 98 in the Operating Instructions.
First-time Operation “OPERATING INSTRUCTIONS (page 7)”
Replace the first "NOTE" for the following. “OPERATING INSTRUCTIONS (page 9)”
NOTE
The power sa ving mode ([Power Sc hemes] in [Control Panel] - [Po wer Management]) is
factory set, so if there is no input from a key, the touch pad or an exter nal mouse (when
one is connected) for a certain interval of time, the pow er to the LCD and hard disk is shut
down. In addition, when the computer is left alone, it automatically enters the suspend*
mode ( "Suspend/Hibernation Functions").
The LCD will resume operation when the touch pad is used, or a key or an externa l
mouse is pressed.
The power to the LCD may be turned off while Windows is setting up or ev en when
an application software is being installed. In this case, because it is conceivable
that a selection dialog box will be sho wn, do not press the Enter key to attempt
to resume from this condition as doing so may trigger a selection, but instead, press
a key unrelated to the direct triggering of a selection, like the key.
*With Windo ws 98, "Suspend" is called "Standby".
Shift
®
Add the following step between and at step 6. “OPERATING INSTRUCTIONS (page 9)”6
Replace the first "NOTE" for the following. “OPERATING INSTRUCTIONS (page 10)”
7
Type a name to identify yourself to Windows, and enter a password (if desired).
NOTE
Follow the on-screen instructions. You can complete these settings at a later
time.
Press [Begin] as necessary. To close the window, click in the top right corner
of the window.
1
Replace the "NOTE" for the following. “OPERATING INSTRUCTIONS (page 11)”
NOTE
When using the files in the following folders available on the retail ver sion of the
Windows CD-ROM, it is necessary to run a separate file decompression program.
\Tools
\Tsclient
To uncompress the file, it is necessary to have approximately
available on the hard disk.
To use the CD-ROM drive or DVD-ROM drive in MS-DOS mode, perform the opera-
tion below after modifying config.sys and autoexec.bat ( "Using a Multimedia Pocket Device").
File decompression method:
1
Turn your computer on.
2
When [Press <F2> to enter SETUP] is displayed, immediately press
(until the menu is displayed).
3
Select [Command prompt only].
4
Insert the Product Recovery CD-ROM.
5
At the prompt, input the following:
L:\en\addfile Enter
Follow the message on the screen.
After this program is ex ecuted, the contents of the above folders will be decompressed
to the c:\util\win98add folder.
80 MB of free disk space
Ctrl
Starting Up/Shutting Down “OPERATING INSTRUCTIONS (page 12)”
2
Replace the first "NOTE" for the following. “OPERATING INSTRUCTIONS (page 13)”
NOTE
The power saving mode ([Power Scheme] in [Control Panel] - [Power Management]) is factory set, so if there is no input from a key, the touch pad, or an external
mouse (when one is connected) for a certain interval of time, the power to the
LCD and hard disk is may be turned off. In addition, when the computer is left
alone, it automatically enters the suspend* mode ( "Suspend/Hibernation Functions").
The LCD will resume operation when the touch pad or an external mouse (when
one is connected) is used or a key is pressed.
*With Windows 98, "Suspend" is called "Standby".
[System Devices] in [Start] - [Settings] - [Control Panel] - [System] - [Device
Manager] may contain a device or devices bearing an exclamation mark or question mark. This does not indicate a malfunction.
Loading...