Panasonic BT-LT2600 User Manual

Page 1
Panasonic Broadcast
BT-LT2600
Menu Information
Page 2

How to Use the On Screen Menu

Input signal status

1. The selected input line (J page 9, )
VIDEO, Y/C, SDI1, SDI2,
SDI1
412 3
YP
BPR/RGB-VIDEO/RGB-COMP.
2. Various display (FILM mode)
Displayed when “FILM” is selected in “GAMMA
SELECT”.
3. Signal format
The display status can be set in “STATUS
DISPLAY” in the “SYSTEM CONFIG” menu (J page 21).
If “UNSUPPORT SIGNAL” is displayed, then either the current input signal is not supported or the “INPUT SELECT” menu setting needs to be changed.
When “NO SIGNAL” is displayed, there is no input signal.
4. Various display (lock setting)
Displayed when control lock is ON.
Note:
“UNSUPPORT SIGNAL” and “NO SIGNAL” may not be displayed correctly.

Picture adjusting knob status

Sharpness display

Picture adjusting knob (J page 9, )
This knob can be rotated and pushed.
The status display appears when the knob is
pushed. The display disappears when the knob is pushed again, or if the knob is not operated for 10 seconds.
Settings can only be adjusted in the status display.
The display position can be changed (J page 21
“ROTARY POSITION”).
Status display: PHASE, CHROMA, BRIGHT, CONTRAST or BACKLIGHT
Note:
The volume knob status display is not displayed on the screen.
Sharpness is displayed when it is set.
The display disappears if remains idle for 2 minutes.
12
SHARPNESS
30
Page 3
How to Use the On Screen Menu (continued)

Function display

You can set FUNCTION display in the menu.
When “FUNCTION DISPLAY” (J page 22) is “ON”
and either [FUNCTION1] or [FUNCTION5] is
F1:MARKER F2:WFM F3:LEVEL METER F4:PIXEL TO PIXEL F5:PIXEL POS.
XXXXX

Audio level meter display

11 33 55 77
22 44 66 88
pressed, the unit displays the status of the FUNCTION item set.
The display disappears if remains idle for 2 seconds.
The operational status is displayed in “XXXXX” (J
page 23 “Operation items displayed when a FUNCTION button is used”).
When the signal is SDI, the audio level is displayed on the white skeleton bar meter.
You can switch the level display on and off, and set the number of displayed channels using the menu.
The 0 dB line and channel display can be switched on and off from the menu.
Channel display
Level display
0 dB line

Menu display

[MAIN MENU]
FUNCTION
HOURMETER
MENU
Displays the operation explanation for the menu button.
This is displayed when the menu is used.
The display disappears if remains idle for 2 minutes.
The display position can be changed (J page 21
“MENU POSITION”).
13
Page 4
How to Use the On Screen Menu (continued)

Menu operations

1. Push [MENU] to display the MAIN menu.
2. Push [ , ] to select the menu, then push [ENTER].
[MAIN MENU]
FUNCTION
HOURMETER
MENU
3. Push [ , ] to select the sub menu, then push [ENTER].
The setting values in the sub menu change to green.
MARKER
MARKER 16:9
4:3 BACK CENTER GPI PRESET1 GPI PRESET2
4. Push [ , ] to select the setting values, then push [ENTER].
Push [MENU] to cancel.
MARKER
MARKER
16:9
4:3 BACK MARKER GPI PRESET1 GPI PRESET2
OFF
OFF OFF
NORMAL
OFF
4:3 4:3
SET
ON
OFF OFF
NORMAL
OFF
4:3 4:3
SET
To return to the previous screen
Push [MENU].
14
Page 5

User Data

You can change the menu setting values and picture adjusting knob settings, then save and load up to 5 combinations of screen adjustment values as user data. You can also return the setting values and adjustment values to the factory preset settings. The following settings are included in user data.
• Menu settings except for “SETUP LOAD/SAVE” (including the button function settings on the front of the monitor)
• Screen adjustment values changed in picture adjusting knob

Saving user data

1. Push [MENU] to display the MAIN menu.
2. Push [ , ] to select the “SYSTEM CONFIG” menu and push [ENTER].
3. Push [ , ] to select the “SETUP SAVE” sub menu and push [ENTER].
The setting values in the sub menu change to green.
CONT./BACK. BACKLIGHT SUB WINDOW WFM POSITION MENU POSITION ROTARY POSITION STATUS DISPLAY SETUP LOAD
SETUP SAVE
FAN MOTOR COLOR SPACE
BACKLIGHT
60
FULL
RB
CENTER
LB
3SEC OFF
FACTORY
USER1
OFF EBU

Loading user data

1. Push [MENU] to display the MAIN menu.
2. Push [ , ] to select the “SYSTEM CONFIG” menu and push [ENTER].
3. Push [ , ] to select the “SETUP LOAD” sub menu and push [ENTER].
The setting values in the sub menu change to green.
CONT./BACK. BACKLIGHT SUB WINDOW WFM POSITION MENU POSITION ROTARY POSITION STATUS DISPLAY
SETUP LOAD
SETUP SAVE FAN MOTOR COLOR SPACE
BACKLIGHT
60
FULL
RB
CENTER
LB
3SEC OFF
FACTORY
USER1
OFF EBU
Changes to green
4. Push [ , ] to select the file you wish to save to from “USER1” – “USER5”, then push [ENTER].
The following screen appears.
SETUP SAVE
5. Select “YES”, and push [ENTER].
The user data is saved.
To return to the previous screen
Push [MENU].
Changes to green
4. Push [ , ] to select the file you wish to load to from “USER1” – “USER5”, then push [ENTER].
The following screen appears. To return to the factory preset setting values, select “FACTORY”.
SETUP LOAD
5. Select “YES”, and push [ENTER].
The user data is loaded.
15
Page 6

Main Menu

Menu configuration

MAIN MENU
MARKER
VIDEO CONFIG
SYSTEM CONFIG
FUNCTION
GPI
INPUT SELECT
AUDIO
CONTROL
HOURMETER
CONT./BACK.
BACKLIGHT
SUB WINDOW
WFM POSITION
MENU POSITION
ROTARY POSITION
STATUS DISPLAY
SETUP LOAD
SETUP SAVE
FAN MOTOR
COLOR SPACE
FUNCTION1
FUNCTION2
FUNCTION3
FUNCTION4
FUNCTION5
FUNCTION DISPLAY
VIDEO/ Y/C
NTSC SETUP
BPR/RGB
YP
COMPONENT LEVEL
RGB SYNC
COMP.
INPUT SELECT
EMBEDDED SELECT L
EMBEDDED SELECT R
LEVEL METER
0 dB POINT
CH
CONTROL
LOCAL ENA.
OPERATION
LCD
FAN
GAMMA SELECT
FILM GAMMA
COLOR TEMP.
SHARPNESS MODE
SHARPNESS H
SHARPNESS V
I-P MODE
MONO
ANAMO
SD ASPECT
SCAN
NOISE WIPE
AUTOSETUP
H POSITION
V POSITION
PHASE
CLOCK
WXGA/XGA
*[WHITE BALANCE VAR1-3]
USER0-63
D93
D65
D56
VAR1
VAR2
VAR3
GPI CONTROL
GPI1
GPI2
GPI3
GPI4
GPI5
GPI6
GPI7
GPI8
MARKER
16:9
4:3
BACK
CENTER
GPI PRESET1
GPI PRESET2
COLOR TEMP.
GAIN RED
GAIN GREEN
GAIN BLUE
BIAS RED
BIAS GREEN
BIAS BLUE
RESET
16
Page 7
Main Menu (continued)

MARKER

The underlined values are factory preset setting values.
Sub menu Settings Explanation MARKER
<OFF> <ON >
16:9
*2*3
<OFF> <4:3 > <13:9> <14:9> <CNSCO> <VISTA> <95%> <93%> <90%> <88%> <80%>
4:3
*2*4
<OFF> <95%> <93%> <90%> <88%> <80%>
BACK
*2
< <HALF> <BLACK>
CENTER
*2
<OFF> <ON>
GPI PRESET1
*5
<4:3> <13:9> <14:9> <CNSCO> <VISTA>
GPI PRESET2
*5
<95% (16:9)> <93% (16:9)> <90% (16:9)> <88% (16:9)> <80% (16:9)> <95% (4:3)> <93% (4:3)> <90% (4:3)> <88% (4:3)> <80% (4:3)>
*1 The setting becomes “On” when the unit receives marker-related control during REMOTE operation. (Priority
goes to GPI when GPI settings exist.)
*2 When controlling the marker settings using the GPI function (J page 30), these settings become disabled.
These are not operated when the 2 screens are displayed. *3 These are only enabled when the HD signal and SD signal aspect ratio settings are 16:9. *4 These are only enabled when the SD signal aspect ratio setting is 4:3. *5 When setting “GPI PRESET1” or “GPI PRESET2” using GPI function, the REMOTE function depending RC-
232C becomes disabled (error response: ER001).
*1
NORMAL
Used to make MARKER settings effective.
Used to select/display the type of marker when the aspect ratio setting is 16:9.
<OFF> Marker not displayed. <4:3> 4:3 marker <14:9> 14:9 marker <VISTA> VISTA marker <93%> 93% <88%> 88%
Area marker Area marker
<13:9> 13:9 marker <
CNSCO
> CNSCO marker <95%> 95% <90%> 90% <80%> 80%
Area marker Area marker Area marker
Used to select/display the type of marker when the aspect ratio setting is 4:3.
<OFF> Marker not displayed. <95%> 95% <90%> 90% <80%> 80%
>
Used to select the background brightness excluding the marker. <
NORMAL
Area marker Area marker Area marker
> Normal background
<93%> 93% <88%> 88%
Area marker Area marker
<HALF> Background brightness 50% <BLACK> Background brightness 0% (Black)
Used to display the center marker. <OFF> Not displayed <ON> Displayed
GPI PRESET1: Used to select the marker to be displayed using the GPI terminal “MARKER1 ON/OFF” operation (J page 30).
GPI PRESET2: Used to select the marker to be displayed using the GPI terminal “MARKER2 ON/OFF” operation (J page 30).
<4:3> 4:3 marker <13:9> 13:9 marker <14:9> 14:9 marker <
CNSCO
>CNSCO marker <VISTA> VISTA marker <95% (16:9)> 95% Area marker when the aspect ratio is 16:9. <93% (16:9)> 93% Area marker when the aspect ratio is 16:9. <90% (16:9)> 90% Area marker when the aspect ratio is 16:9. <88% (16:9)> 88% Area marker when the aspect ratio is 16:9. <80% (16:9)> 80% Area marker when the aspect ratio is 16:9. <95% (4:3)> 95% Area marker when the aspect ratio is 4:3. <93% (4:3)> 93% Area marker when the aspect ratio is 4:3. <90% (4:3)> 90% Area marker when the aspect ratio is 4:3. <88% (4:3)> 88% Area marker when the aspect ratio is 4:3. <80% (4:3)> 80% Area marker when the aspect ratio is 4:3.
17
Page 8
Main Menu (continued)

Types of MARKER

g 16:9 marker
(Displayed when using HD, or when using SD with a 16:9 aspect ratio)
The marker is only displayed as a vertical bar. In addition, the section becomes the “MARKER BACK” item.
4:3 marker 13:9 marker
14:9 marker
VISTA marker, CNSCO marker
A horizontal dotted line is displayed as the marker.
g
4:3 marker (Displayed when using SD with a 4:3 aspect ratio)
A dotted line is displayed as the marker.
95% Area marker 93% Area marker
90% Area marker 88% Area marker
80% Area marker
(Displayed when using HD, or when using SD with a 16:9 aspect ratio)
A dotted line is displayed as the marker.
VISTA marker CNSCO marker
When “UNDER” is set in “SCAN” in the “VIDEO CONFIG” menu, a vertical dotted line is also displayed as the marker.
VISTA marker CNSCO marker
Area marker
A dotted line is displayed as the marker.
95% Area marker 93% Area marker
90% Area marker 88% Area marker
95% Area marker 93% Area marker
90% Area marker 88% Area marker
80% Area marker
*
You can display 4:3 marker at the same time as 16:9 marker.
Simultaneously display example
The section becomes the “MARKER BACK” item. The background selected with the 16:9 marker is controlled.
16:9 marker:
80% Area marker
95% Area marker
95% Area marker
4:3 marker:
80% Area marker
80% Area marker
18
g Center marker
Center marker The marker is displayed in the center of the picture.
Page 9
Main Menu (continued)

VIDEO CONFIG

Sub menu Settings Explanation GAMMA
SELECT
*1*2
<STANDARD> <FILM>
<STDIO/PST>
Used to select the gamma curve. <STANDARD>Standard mode <FILM>FILM mode <STDIO/PST>Color emphasis mode (in the gamma characteristic in
which shades are valued more than the contrasts, it is suitable for use by the studio and the post production, etc. )
When FILM is selected, mark is displayed in the top left of the screen.
The underlined values are factory preset setting values.
FILM GAMMA
*2
<VARICAM> <OTHER>
Used to select the type of FILM gamma mode. <VARICAM> VARICAM use
<OTHER> When using other types than VARICAM
COLOR TEMP.
SHARPNESS
*2
MODE
SHARPNESS H
<USER0–63> <D93> <D65> <D56> <VAR1> <VAR2> <VAR3>
<HIGH> <LOW>
*2
<0–30>
*5
Used to select the color temperature. <USER0–63> Adjustable settings 0–63 (color temperature around 3000K–9300K) <D93> Color temperature around 9300K <D65> Color temperature around 6500K <D56> Color temperature around 5600K <VAR1> WB adjustment mode <VAR3> WB adjustment mode
*3
Used to select the width of the sharpness edge.
*4
<VAR2> WB adjustment mode
*4
<HIGH> Thin edge <LOW> Thick edge
*3
Used to set the sharpness in the horizontal direction. When adjusting, the item display moves to the lower part of the screen.
SHARPNESS V
*2
<0–30>
*3
Used to set the sharpness in the vertical direction. When adjusting, the item display moves to the lower part of the screen.
I-P MODE
MONO
*2
*2*6
<MODE2> <MODE1>
<OFF> <ON>
Used to select IP conversion mode. (J page 20 : About IP Mode) <MODE2> Field Interpolation <MODE1> Frame Interpolation
Used to switch between color and monochrome (MONO). <OFF> Color <ON> Monochrome
* When this is ON, the picture adjusting knob [CHROMA] setting is fixed at 0.
ANAMO
*2*7
<OFF> <ON>
If an Anamo lens has been used on the camera, and input through SDI 720/60P, 59.94P, the picture is resized to Anamo size magnification. (a vertically compressed signal can be amplified vertically and corrected when it is displayed.)
SD ASPECT
*2
SCAN
NOISE WIPE
*2
*2
<4:3> <16:9>
<NORMAL> <UNDER>
<OFF> <ON>
Used for setting the aspect ratio settings when using SD signal input. <4:3> 4:3 display <16:9> 16:9 display
Used to set under-scan and normal display. <NORMAL>Normal display <UNDER>Under-scan
<OFF> This makes a fluid and smooth contrast obtainable.
This is especially effective for continuously changing the contrast of the source signal or CG signal when the S/N is very high.
<ON> Noise reduction mode. Depending on the camera, this mode can
be especially effective for dark scenes. We recommend leaving this setting “ON” under normal conditions.
*1 During 2 screen display, the changes are not reflected in the still image of the main window.
BPR
*2 When “RGB-COMP.” is selected in “YP
/RGB” in the “INPUT SELECT” menu (J page 27), this does not operate.
*3 The following sharpness values can each be set,
1) VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
2) any other input line’s HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0)
3) any other input line’s SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0) and the setting values for the selected input signal from within this group is displayed. The adjustment status is displayed in the bottom right when selected.
J
*4 When “VAR1”, “VAR2” or “VAR3” is selected, the monitor switches to WB adjustment mode (
page 20).
*5 When selecting USER0–63
1) Push [ENTER] (USER changes to blue). 2) Select 0–63 with [ , ], and push [ENTER].
*6 When using
1) change the setting after releasing
2) we recommand
“SUB WINDOW” function (J page 24),
“SUB WINDOW” function
“MODE2” for the image with a fast movement.
.
*7 During Anamo size display, “SCAN” change is not reflected.
*4
19
Page 10
Main Menu (continued)
3
About IP Mode
By selecting “MODE1”, you can convert IP through Frame Interpolation. This unit has reduced the Frame Interpolation delay to 1 field or less, compared to our old models having caused 1 frame delay or more. Factory preset setting value is “MODE1” recommended for normal use. Depending on images, in very rare cases, noise may occur on the screen. In such a case, “MODE 2” is recommended.
By selecting “MODE2”, you can convert IP through Field Interpolation. Depending on still images, etc., flickers may occur on the screen. In such a case, “MODE 1” is recommended.
g WB adjustment mode
You can adjust “WHITE BALANCE VAR1” – “WHITE BALANCE VAR3” (WB) by selecting “VAR1” – “VAR3” in “COLOR TEMP.” in the “VIDEO CONFIG” menu.
The underlined values are factory preset setting values.
Sub menu Settings Explanation
COLOR TEMP.
*1
GAIN RED
GAIN GREEN
GAIN BLUE
BIAS RED
BIAS GREEN
BIAS BLUE
RESET
*1 When “COLOR TEMP.” is selected and [ENTER] is pressed following item change, the display changes to the
confirmation screen. Selecting “YES” and pressing [ENTER] on this screen return GAIN and BIAS values to the selected color temperature values.
*2 When adjusting, the item display moves to the lower part of the screen.
<USER0–63> <D93> <D65> <D56>
<0–511> (Factory presets are values for color temperature <D65>.) * The presets are values
adjusted before shipment from factories.
<-512–511> (Factory preset settings: 0)
Used to select the color temperature that will become the basis for adjustments. <USER0–63>
Adjustable settings 0–63 (color
temperature around 3000K–9300K) <D93> Color temperature around 9300K <D65> Color temperature around 6500K <D56> Color temperature around 5600K
GAIN elements for RED are adjusted.
GAIN elements for GREEN are adjusted.
GAIN elements for BLUE are adjusted.
BIAS elements for RED are adjusted.
BIAS elements for GREEN are adjusted.
BIAS elements for BLUE are adjusted.
*2
*2
*2
*2
*2
*2
“GAIN RED” – “BIAS BLUE” values are reset to color temperatures values selected in “COLOR TEMP.”.
20
Page 11
Main Menu (continued)

SYSTEM CONFIG

The underlined values are factory preset setting values.
Sub menu Settings Explanation CONT./BACK.
BACKLIGHT
SUB WINDOW
WFM POSITION
MENU POSITION
ROTARY POSITION
STATUS DISPLAY
SETUP LOAD
SETUP SAVE
FAN MOTO R
COLOR SPACE
*1 When the monitor is shipped from the factory, “USER1” – “USER5” and “FACTORY” all have the same details. *2 You cannot save or load the settings for “H POSITION”, “V POSITION”, “PHASE” and “CLOCK” (J page 27). *3 Factory preset settings are The U.S.A. and Canada: SMPTE-C, Others: EBU.
<CONTRAST> <BACKLIGHT>
Used to select the function to be assigned to [CONTRAST/ BACKLIGHT] (a knob on the front panel). <CONTRAST>
Used to adjust CONTRAST.
<BACKLIGHT>
Used to adjust BACKLIGHT.
< 0-60
> Used to adjust the LCD backlight level.
<FULL> <PART>
Used to select the type of sub window. <FULL>
Used to reduce the whole input signal screen, and arrange it horizontally when it is displayed.
<PART>
Used to cut out the central section of the input signal screen, and arrange it horizontally when it is displayed (Displayed at the same size as the previous screen).
<LB> <RB> <RT>
Used to set the WFM display position. <LB> Bottom left of the screen <RB> Bottom right of the screen <RT> Top right of the screen <LT> Top left of the screen
<LT>
<CENTER> <LB> <RB> <RT>
Used to set the on screen menu display position. <CENTER> Center of the screen <LB> Bottom left of the screen <RB> Bottom right of the screen <RT> Top right of the screen <LT> Top left of the screen
<LT>
<CENTER> <LB> <RB> <RT> <LT>
<CONTINUE> <3SEC OFF> <OFF>
Used to set the picture adjusting knob status (on screen menu) display position. <CENTER> Center of the screen <LB> Bottom left of the screen <RB> Bottom right of the screen <RT> Top right of the screen <LT> Top left of the screen
Used to set the input signal status (on screen menu) display status. <CONTINUE> Displayed normally. <3SEC OFF> After changing status, it is displayed for approximately
3 seconds, and then disappears.
<OFF> Not displayed.
<FACTORY> <USER1> <USER2> <USER3> <USER4> <USER5>
<USER1> <USER2> <USER3> <USER4> <USER5>
*1*2
*1*2
*1*2
*1*2
*1*2
*2
*2
*2
*2
*2
<OFF> <ON>
The saved factory preset setting values (FACTORY) or the user data (USER 1–USER 5) are loaded. Also after loading user data, the screen displays the signal selected before loading data.
Up to 5 sets of user data can be saved (J page 15). The menu settings and picture adjusting knob adjustment values (PHASE /CHROMA /BRIGHT /CONTRAST) excluding “SETUP SAVE/ SETUP LOAD” are saved.
Used to set fan operation. <OFF> The fan is stopped. The brightness of the backlight
automatically lowers.
<ON> The fan operates. The backlight brightness returns to normal.
<EBU>
*3
<SMPTE-C>
Used to set studio-specified colors.
*3
21
Page 12
Main Menu (continued)

FUNCTION

The underlined values are factory preset setting values.
Sub menu Settings Explanation FUNCTION 1 –
FUNCTION 5
FUNCTION DISPLAY
*1 If these settings are changed, the menu settings will also change.
<HV DELAY> <AUTOSETUP> <BLUE ONLY> <GAMMA SELECT> <SD ASPECT> <SCAN> <SUB WINDOW> <WFM> <MARKER> <PIXEL TO PIXEL> <PIXEL POS.> <LEVEL METER> <MONO> <UNDEF>
(Factory preset settings FUNCTION1: MARKER FUNCTION2: WFM FUNCTION3: LEVEL METER FUNCTION4: PIXEL TO PIXEL FUNCTION5: PIXEL POS.)
<ON> <OFF>
Used to select the functions to be assigned to individual buttons [FUNCTION1] to [FUNCTION5] (front-panel buttons). <HV DELAY>
Displays the synchronizing signal (horizontal, vertical). The display is switched in the following order.
DELAY OFF J V DELAY J H DELAY J HV DELAY J DELAY OFF
<AUTOSETUP>
Used to automatically adjust the PC display.
<BLUE ONLY>
Used to cut the red and green signals. You can check the hue (PHASE) and depth of color (CHROMA). This is switched between ON/OFF by pushing the button.
<GAMMA SELECT>
Used to display the gamma curve. The display changes in the following order.
GAMMA STANDARD J GAMMA FILM J GAMMA STDIO/PST J GAMMA STANDARD
<SD ASPECT>
Used to switch between “16:9” and “4:3”.
<SCAN>
You can switch between “UNDER SCAN” and “NORMAL SCAN”.
<SUB WINDOW>
You can perform the settings for 2 screen display mode. The display changes in the following order.
<WFM>
Used to display the wave form monitor.
<MARKER>
Used to switch the marker on and off.
<PIXEL TO PIXEL>
Used to switch the display between the input size and display size.
<PIXEL POS.>
Used to set the signal display position when PIXEL TO PIXEL is on.
<LEVEL METER>
Used to switch the AUDIOMETER display. The display changes in the following order.
<MONO>
Used to switch the display between color and black-and­white.
<UNDEF>
No settings
Used to make display settings for the functions assigned to individual buttons [FUNCTION1] to [FUNCTION5] (front­panel buttons). <ON>
The selected function is displayed.
<OFF>
The selected function is not displayed.
*1
SINGLE J FULL/PARTJ STILLJ SINGLE
METER 8CH J METER 4CH J METER 2CH J OFFJ METER 8CH
*1
*1
22
Page 13
Main Menu (continued)
g Restrictions on various FUNCTION settings
Under the following conditions, various settings are disabled.
Setting Disabling condition HV DELAY
AUTO SETUP
GAMMA SELECT
SD ASPECT
SCAN
SUB WINDOW
WFM
MARKER
PIXEL TO PIXEL
PIXEL POS.
MONO
In SUB WINDOW, WFM or PIXEL TO PIXEL mode, “INVALID FUNCTION” is displayed and the setting is disabled. When “YP
BPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.”, “INVALID FUNCTION” is
displayed and the setting is disabled.
When “YP
BPR/RGB” set in “INPUT SELECT” menu is other than “RGB-COMP.”, “NOT RGB-
COMP. CH” is displayed and the setting is disabled. When “YP
BPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.” and there is NO SIGNAL,
“INCOMPLETE” is displayed and the setting is disabled.
When GPI item is set, “INVALID FUNCTION” is displayed and the setting is disabled. When “YP
BPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.”, “INVALID FUNCTION” is
displayed and the setting is disabled.
When GPI item is set, “INVALID FUNCTION” is displayed and the setting is disabled. When SUB WINDOW (still picture) or HD display (including PIXEL TO PIXEL) is on, “INVALID FUNCTION” is displayed and the setting is disabled.
When GPI item is set, “INVALID FUNCTION” is displayed and the setting is disabled. In SUB WINDOW or PIXEL TO PIXEL mode, “INVALID FUNCTION” is displayed and the setting is disabled.
When “YP
BPR/RGB” set in “INPUT SELECT“ menu is other than “RGB-COMP.”, “INVALID
FUNCTION” is displayed and the setting is disabled. When “RGB-COMP.” is selected in SUB WINDOW with a motion picture on, the screen turns SINGLE. When an item other than “RGB-COMP.” is selected, two motion pictures are displayed on the screen. When a still picture is on, blackout occurs.
In SUB WINDOW or PIXEL TO PIXEL mode, “INVALID FUNCTION” is displayed and the setting is disabled. When “YP
BPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.” or “RGB-VIDEO”, “INVALID
FUNCTION” is displayed and the setting is disabled.
When “YP
BPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.”, “INVALID FUNCTION” is
displayed and the setting is disabled. When GPI item is set or in SUB WINDOW mode, “INVALID FUNCTION” is displayed and the setting is disabled.
When “YP
BPR/RGB” set in “INPUT SELECT” menu is “RGB-COMP.” or “RGB-VIDEO”, “INVALID
FUNCTION” is displayed and the setting is disabled. In SUB WINDOW mode, “INVALID FUNCTION” is displayed and the setting is disabled.
When PIXEL TO PIXEL is OFF, “PIXEL TO PIXEL OFF” is displayed and the setting is disabled. When PIXEL TO PIXEL is 720P display, the position becomes CENTER. When the display position is not CENTER in PIXEL TO PIXEL mode during 1080P display and the 720P signal is selected, the display position moves to CENTER.
When GPI item is set, “INVALID FUNCTION” is displayed and the setting is disabled.
g Operation items displayed when a FUNCTION button is used
When any of the buttons, [FUNCTION1] to [FUNCTION5], is pressed, the following messages are displayed according to the operation assigned to the pressed button.
•HV DELAY
DELAY OFF, V DELAY, H DELAY, HV DELAY
• AUTOSETUP
COMPLETE: Display for completion INCOMPLETE: Display for incompletion NOT RGB-COMP. CH
• GAMMA SELECT
GAMMA STANDARD, GAMMA FILM, GAMMA STDIO/PST
• SCAN
NORMAL SCAN, UNDER SCAN
• SUB WINDOW
• MARKER
MAKER OFF, 4:3 MARKER, 13:9 MARKER, 14:9 MARKER, VISTA MARKER, CNSCO MARKER, 95% MARKER, 93% MARKER, 90% MARKER, 88% MARKER, 80% MARKER
• PIXEL TO PIXEL/PIXEL POSITION
CENTER, LEFT TOP, LEFT BOTTOM, RIGHT TOP, RIGHT BOTTOM PIXEL TO PIXEL OFF
• LEVEL METER
METER OFF, METER 2CH, METER 4CH, METER 8CH
SINGLE, FULL/PART, STILL
23
Page 14
P
P
P
P
Main Menu (continued)
g About HV DELAY
This displays the video blanking period. By pushing the button, you can switch through the H blanking display J V blanking display J H and V blanking display J no blanking display.
g About the SUB WINDOW
You can compare saved still and moving images by using the “SUB WINDOW” function to separate the main window into 2 displays as shown below. Depending on the settings of the “SUB WINDOW” (FULL, PART) in the “SYSTEM CONFIG” menu (J page 21) it can be switched as shown below. The display changes each time you press one of the buttons, [FUNCTION1] to [FUNCTION5] (J page 22), assigned with the [SUB WINDOW] function. (To use the “SUB WINDOW” function, you must assign it to one of the [FUNCTION1] to [FUNCTION5] buttons.)
When setting “I-P MODE” function (J page 19),
1)change the setting after releasing “SUB WINDOW” function.
2)we recommand “MODE2” for the image with a fast movement.
•FULL
The main window is reduced and made into 2 sub window (sub window+sub window).
Press the FUNCTION button assigned with the SUB WINDOW function.
Normal window
(main window)
ress the same button again.
moving image
Before inputting the image (sub window+sub window)
moving image moving image
After inputting the image
(sub window+sub window)
ress the same button again.
still image moving image
•PART
Only the sub window size is cut out of the main window, and the cut section is made into 2 sub window images (sub window+sub window).
Press the FUNCTION button assigned with the SUB WINDOW function.
Normal window
(main window)
ress the same button again.
moving image
Before inputting the image (sub window+sub window)
moving image moving image
After inputting the image
(sub window+sub window)
ress the same button again.
still image moving image
The central section is cut out Lines up and displays the
section cut out of the main window
The window is displayed in 16:9 aspect.
Precautions when selecting FULL/PART
This function compares screens with the same input terminal and same format. If different input formats, or if signals are input between different input channels, the sub-window (left side, still image) becomes blurred and blanking occurs. However, if the same format signals are input into the input terminal when acquiring the still image, the images will be displayed correctly.
24
Page 15
P
Main Menu (continued)
g About WFM
You can display the wave form monitor using the “WFM” function. The display changes each time you press one of the buttons, [FUNCTION1] to [FUNCTION5] (J page 22), assigned with the [WFM] function (To use the “WFM” function, you must assign it to one of the [FUNCTION1] to [FUNCTION5] buttons).
Press the FUNCTION button assigned with the WFM function once.
Normal window WFM display
ress the same button again.
WFM (Wave Form Monitor)
The window is displayed in 16:9 aspect.
Restrictions on WFM
Even if “WFM” has turned ON”, “WFM” is not displayed when using the “PIXEL TO PIXEL” function, “YP
BPR/RGB”
set in “INPUT SELECT” menu is “RGB-COMP.” or “RGB-VIDEO”, or using the “SUB WINDOW” function.
g About PIXEL TO PIXEL and PIXEL POS.
Using the “PIXEL TO PIXEL” function, you can confirm a picture with the actual pixel count (only when the input is an HD signal). First, press one of the buttons, [FUNCTION1] to [FUNCTION5] (J page 22), assigned with the “PIXEL TO PIXEL” function to turn it “ON”. With the function on, press another one of the buttons, [FUNCTION1] to [FUNCTION5] (J page 22), assigned with “PIXEL POS.”. Each time the button assigned with “PIXEL POS.” is pressed, the signal display position switches. (To use the “PIXEL TO PIXEL” function, “PIXEL TO PIXEL” and “PIXEL POS.” must be assigned to any two of the buttons, [FUNCTION1] to [FUNCTION5].)
The underlined values are factory preset setting values.
Sub menu Settings Explanation
PIXEL TO PIXEL
PIXEL POS.
*1*2
<OFF> <ON>
<CENTER> <LEFT TOP> <RIGHT TOP> <RIGHT BOTTOM> <LEFT BOTTOM>
Used to set the input signal size as the display size. Compatible formats 1080/60I/59I/50I/30P/29P/25P/24P/23P/24P 720/60P/59P/50P(SDI/YP
Used to set the signal display position when PIXEL TO PIXEL
*3
is on.
BPR)
SF/23PSF,
<CENTER> center <LT> top left <RT> top right <RB> bottom right <LB> bottom left
*1 When PIXEL TO PIXEL is on, the following menu settings become invalid:
“ON” for “ANAMO” and “UNDER” for “SCAN” set in “VIDEO CONFIG” Various “HV DELAY” settings in “FUNCTION” “MARKER display”
*2 When the input signal is “SDI1”, “SDI2” or “YP
BPR”, the setting takes effect. However, 1080/60P and 1080/50P
signals are excluded.
*3 When the input signal format is 720, only CENTER is displayed.
25
Page 16
Main Menu (continued)
GPI
The “GPI CONTROL” item is used to set enable/disenable of all GPI functions, and assigns functions to each of the GPI terminal pins (J page 30).
The underlined values are factory preset setting values.
Sub menu Settings Explanation GPI CONTROL
GPI1–GPI8
<DISENABLE> <ENABLE>
<UNDEF> <MARKER1 ON/OFF> <MARKER2 ON/OFF> <MARKER BACKHALF> <MARKER BACKBLACK > <CENTER MARKER> <INPUT SEL. VIDEO> <INPUT SEL. Y/C> <INPUT SEL. SDI1> <INPUT SEL. SDI2> <INPUT SEL. YP <SD ASPECT> <SCAN> <R-TALLY> <G-TALLY> <MONO> <GAMMA SEL. FILM> <GAMMA SEL. STDIO/ PST> <RGB SYNC>
BPR/RGB>
GPI functions enable/disenable settings
Used to set the GPI control terminal pin assign. You can set the same items for each terminal (refer to page 30 for details).
Note:
Please be aware that the following can not be performed.
“SD ASPECT” operation when input signal is HD or PC
“SCAN” operation when the input signal is PC
“GAMMA SELECT” operation when the input signal is PC
“RGB SYNC” operation when anything other than “RGB-VIDEO” is selected in “YP
SELECT” menu
“MONO” operation when input signal is PC
BPR/RGB” in the “INPUT
26
Page 17
Main Menu (continued)

INPUT SELECT

The underlined values are factory preset setting values.
Sub menu Settings Explanation VIDEO / Y/C
NTSC SETUP
YP
BPR/RGB
COMPONENT LEVEL
RGB SYNC
COMP.
“AUTO” is set when the monitor is shipped from the factory, but if there are concerns about noise etc. from outside the
*1
input signal, we recommend assigning specific format.
<AUTO> <NTSC> <PAL>
<75> <00>
<YP
BPR>
<RGB-VIDEO> <RGB-COMP.>
<SMPTE> <B75> <B00>
<G-ON> <EXT>
Used to select the input format for VIDEO and Y/C input. <AUTO> Either NTSC or PAL is automatically selected. <NTSC> NTSC <PAL> PAL
Selects the NTSC setup level. <75> Select this when using with a setup signal of
7.5 IRE. (The inner parts of the monitor are set to the 7.5 IRE setup level to suit the black level)
<00> Select this when there is no setup level signal.
Selects either YP <YP
BPR> Selects the YPBPR signal.
<RGB-VIDEO> <RGB-COMP.>
Selects YP
BPR (Component) or RGB input mode.
Selects the video RGB signal. Selects the PC RGB signal.
BPR (Component) signal input level.
<SMPTE> When the signal level specified in SMPTE is
Chroma 100 IRE P
B, PR = 0.7 Vp-p.
<B75> Select this when connecting a betacam or
simliar devices set to 7.5 IRE. (The inner parts of the monitor are set at 7.5
IRE
setup level to
suit the black level)
<B00> Select this when connecting a betacam or similar
devices that are not setup to the IRE level.
Selects the SYNC when using RGB-VIDEO input. <G-ON> Select when a synchronizing signal is
superimposed on the G signal.
<EXT> Select when an external synchronizing signal is
received in synchronization.
Performs analog PC settings. (Refer to “COMP.” below)
*1
g COMP.
The following menus are switched by selecting “RGB-COMP.” in “YP
The underlined values are factory preset setting values.
BPR/RGB” in the “INPUT SELECT” menu.
Sub menu Settings Explanation
AUTOSETUP
*1
Screen automatic adjustment is performed when “RGB­COMP.” is selected in “YP
BPR/RGB” in the “INPUT SELECT”
menu. “AUTOSETUP” is performed if a different screen is displayed, and “YES” is selected.
H POSITION
V POSITION
PHASE
<0–60> (Factory preset setting: 30)
<0–60> (Factory preset setting: 30)
<0–31>
Used to adjust the picture display position in the horizontal direction.
Used to adjust the picture display position in the vertical direction.
Used to adjust the clock phase with 1/32 clock phases.
*2
*2
*2
(Factory preset settings:
J page 28)
CLOCK
<700–1800>
Used to adjust the sampling clock in dot units.
*2
(Factory preset settings:
J page 28)
WXGA/XGA
<XGA>
Switches between WXGA and XGA.
<WXGA>
*1 “EXECUTING” is displayed while “AUTOSETUP” is being executed, and “COMPLETE” is displayed when
“AUTOSETUP” is completed. If “AUTOSETUP” cannot be completed, “INCOMPLETE” is displayed.
*2 Each “RGB-COMP.” input compatible format can be adjusted, but you cannot load (“SETUP LOAD” J page 21)
or save (“SETUP SAVE” J page 21) the user data.
27
Page 18
Main Menu (continued)
g “PHASE” and “CLOCK” factory preset setting values
FORMAT CLOCK PHASE FORMAT CLOCK PHASE
640x400(70Hz) 800 18 1024x768(60Hz) 1344 1
640x480(60Hz) 800 18 1024x768(70Hz) 1328 21
640x480(75Hz) 840 10 1024x768(75Hz) 1312 9
640x480(85Hz) 832 5 1024x768(85Hz) 1376 9
800x600(60Hz) 1056 27 1280x768(60Hz) 1728 1
800x600(75Hz) 1056 7 1280x768(75Hz) 1712 22
800x600(85Hz) 1048 24 1280x1024(60Hz) 1688 12

AUDIO

Adjusting the speaker output.
The underlined values are factory preset setting values.
Sub menu Settings Explanation INPUT
SELECT
EMBEDDED SELECT L
EMBEDDED SELECT R
LEVEL
METER
0dB POINT
CH
*1 When speaker output set in “INPUT SELECT” menu is analog, the level meter does not move regardless of its
*1
display status.
<AUTO> <ANALOG>
<CH1–CH8> (Factory preset setting: CH1)
<CH1–CH8> (Factory preset setting: CH2)
<OFF> <8CH> <4CH> <2CH>
<ON> <OFF>
<ON> <OFF>
Used to select speaker output. <AUTO> When SDI input line is selected with [INPUT SELECT] on the front
panel:
embedded audio (SDI terminal) When an input line other than SDI1 and SDI2 is selected with [INPUT SELECT] on the front panel:
analog (AUDIO input terminal)
<ANALOG> Analog (AUDIO input terminal)
Used to select the audio channel of the embedded audio outputted to the left speaker.
Used to select the audio channel of the embedded audio outputted to the right speaker.
Used to select the embedded audio meter for on-screen display.
Used to switch the 0 dB line displayed on the meter on and off.
Used to switch the channel displayed on the meter on and off.
28
Page 19
Main Menu (continued)

CONTROL

The underlined values are factory preset setting values.
Sub menu Settings Explanation CONTROL
LOCAL
*2
ENA.
*1 The menu can be displayed when the lock is engaged.
The only menu setting that can be changed when the lock is engaged is the “CONTROL/LOCAL ENA.” item. When the lock is engaged, the picture adjusting knob is disabled. Operations when the lock is engaged follow the settings in “LOCAL ENA.”.
When the lock is engaged, the volume knob can be operated (J page 9, ). When the lock is engaged, the key mark is displayed on the screen.
<LOCAL> <REMOTE>
<DIS.> <INPUT>
Used to select the operation. (Combined control lock) <LOCAL> Front operation enabled
<REMOTE>
Remote operation enabled (The front controls become locked)
When “REMOTE” is selected in “CONTROL”, this selects whether front controls are enabled/disenabled. <DIS.>
A
ll front operations are disabled.
<INPUT> All controls except for the [INPUT SELECT] button and
volume knob are disabled.
*1
[MAIN MENU]
Key mark
MARKER
*2 This is only enabled when “CONTROL” is set to “REMOTE”.

HOURMETER

The underlined values are factory preset setting values.
Sub menu Settings Explanation OPERATION
LCD
FAN
<XXH>
<XXH>
<XXH>
*3 Time is displayed in “XX”. *4 Linked with the FAN MOTOR ON/OFF status.
*3
*3
*3
Used to display the power distribution time.
Used to display the backlight activation time.
Used to display the FAN operation time.
*4
29
Loading...