Panasonic AW-HB605 User Manual
Before attempting to connect, operate or adjust this product, please
read these instructions completely.
Multi Control Hub
Model AW- P
P
O
W
E
R
O
FF
O
N
Multi Control Hub AW
–
32
indicates safety information.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (service)
instructions in the literature accompanying the appliance.
indicates safety information.
FCC Note:
This device complies with Part 15 of the FCC Rules. To assure continued
compliance follow the attached installation instructions and do not make any
unauthorized modifications.
This equipment has been tested and found to comply with the limits for a class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
CAUTION:
Do not install or place this unit in a bookcase, built-in cabinet or any
other confined space in order to maintain adequate ventilation. Ensure
that curtains and any other materials do not obstruct the ventilation to
prevent risk of electric shock or fire hazard due to overheating.
WARNING:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
CAUTION:
O
Keep the temperature inside the rack to between 14°F to 113°F
(–10°C to 45°C).
54
For Your Safety
O
Use the dedicated AC adapter (AW-PS505) to supply power to the multi control hub.
O
Handle with care.
The multi control hub may malfunction if it is dropped or exposed to strong shocks.
O
Use within a temperature range of 14°F to 113°F (–10°C to +45°C).
Using the multi control hub in environments colder than 14°F (–10°C) or hotter than
113°F (+45°C) could have a damaging effect on the internal components.
O
Connect and disconnect cables only when the power is turned off.
Make sure to turn the power to the multi control hub off before connecting or
disconnecting cables.
O
Avoid using the multi control hub outdoors.
O
Place the multi control hub a minimum of 1 meter away from monitor video screens.
O
Cleaning
Unplug the multi control hub and wipe it clean using a dry cloth. For dirt that cannot be
removed in this manner, moisten a cloth with kitchen detergent, wring it out thoroughly,
and then wipe gently.
• Never use volatile chemicals such as benzene or paint thinner to clean the multi
control hub.
• Before using chemically treated cloths to clean the multi control hub, read their
instructions and precautions thoroughly.
Accessories
O
Priority switchboxes: 5
O
Rack mounting brackets: 12
O
Mounting screws: 24
Overview
O
The AW-HB605 multi control hub combines with a system such as the Panasonic AWPH300 series indoor pan/tilt head or AW-PH600 series outdoor pan/tilt head to support
the connection of between one and five control panels (AW-RP501, AW-RP301, AWRP305) to a single camera and pan/tilt head. Any of the connected control panels may
then be used to control the camera and pan/tilt head (the AW-RP301 and AW-RP305
can control the pan/tilt head only).
In addition, by adding the AW-HB505 multi port hub and AW-RP505 multi hybrid control
panel, it is possible to construct a system in which between one and five multi hybrid
control panels may be used to control between one and five cameras and pan/tilt heads.
O
When coaxial cable/s (5C-2V) and 10BASE-T (UTP category 5) straight cable/s
(10BASE-T cable only for the AW-RP301 and AW-RP305) are used to make
connections, the distance between the cameras and pan/tilt heads and the control
panels can be extended up to a maximum of 500 meters.
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . 4
Accessories . . . . . . . . . . . . . . . . . . . . . . 4
For Your Safety. . . . . . . . . . . . . . . . . . . . 5
Controls and Their Functions . . . . . . . . 6
$
Front Panel. . . . . . . . . . . . . . . . . . . . 6
$
Rear Panel . . . . . . . . . . . . . . . . . . . . 7
$
Priority Switchbox. . . . . . . . . . . . . . 10
System Connections . . . . . . . . . . . . . . 11
Operations. . . . . . . . . . . . . . . . . . . . . . . 17
Rack Mounting Example . . . . . . . . . . . 18
$
Rack Mounting Procedure . . . . . . . 18
Specifications . . . . . . . . . . . . . . . . . . . . 19
76
Controls and Their Functions
PREVIEW OUT
CAM CONT IN
5
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
4
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
TO CONTROL PANEL TO PAN/TILT HEAD HUB
CAM CONT IN
3
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
2
PAN/TILT
CONTROL IN
BLACK
BURST OUT
PREVIEW OUT
CAM CONT IN
1
PAN/TILT
CONTROL IN
BLACK
BURST OUT
BLACK
BURST
OUT
PREVIEW IN
CAM CONT OUT
PAN/TILT
CONTROL OUT
+-
DC12V IN
9
8
45
7
;
:
6 3
3
DC +12 V Input Connector [DC12 V IN]
(4-pin Cannon Connector)
Connect the AW-PS505 AC adapter
(sold separately) to this connector.
4
Pan/Tilt Head Control Signal Output
Connector [TO PAN/TILT HEAD HUB
PAN/TILT CONTROL OUT] (RJ-45 8pin Modular Jack)
Connect this connector to the control
signal input connector [P/T CONTROL
IN] of the AW-PH300 or AW-PH600
pan/tilt head, or to the pan/tilt control
signal input connector [TO CONTROL
PANEL PAN/TILT CONTROL IN] of the
AW-HB505 multi port hub using a
10BASE-T (UTP category 5) straight
cable.
5
Preview Video Signal Input
Connector [TO PAN/TILT HEAD HUB
PREVIEW IN] (BNC Connector)
Connect this connector to the video
signal output connector [VIDEO OUT] of
the pan/tilt head, or to the preview video
signal output connector [TO CONTROL
PANEL PREVIEW OUT] of the multi
port hub using a coaxial cable (5C-2V
equivalent).
<Note>
In a system incorporating the AWRP301 or AW-RP305, the control panel
is not equipped with a video signal cable
compensation circuit. It may therefore
be necessary to use a separate cable
compensation device in some cases.
$
Rear Panel
Controls and Their Functions
$
Front Panel
1
Power Indicator LED [POWER]
This indicator lights (red) when the
power switch 2is at the ON position. It
is dark when the power switch 2is at
the OFF position.
2
Power Switch [POWER ON/OFF]
Placing this switch at the ON position
when the AC adapter is connected and
turned on supplies power to the multi
control hub (power indicator LED lights).
Placing it at the OFF position cuts off
the power.
<Note>
This switch must be at the ON position
in order to control the camera and
pan/tilt head from each control panel.
POWER
OFF ON
1
2
Multi Control Hub AW–
Loading...