2
The AJ-YAC150P is an SDTI interface board for the
AJ-HD150. Consult your dealer before attempting
to install it into the AJ-HD150.
O Do not touch this product with wet hands.
O Do not drop this product or subject it to strong impact.
O Do not remodel this product. Doing so may cause
malfunctioning.
AJ-YAC150P main unit
The AJ-YAC150P is an SDTI interface board for the AJHD150.
By installing this board into the AJ-HD150, it is possible to
input and output digital data using the SDTI format
21
(compression digital interface).
21
SDTI (Serial Data Transport Interface) complies with the
SMPTE305M standard.
The data stream format complies with the SMPTE312M
standard.
Connection area
Serial digital input connector (BNCt1)
1. Input: Dedicated SDTI input
Serial digital output connector (BNCt1)
2. Output: Dedicated SDTI output
Cautions
Features
HD SDI
IN
IN
(OPTION)
OUT
HD SDTI
OUT 1
OUT 2
OUT 3
(SUPER)
3
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Installing the AJ-YAC150P board. . . . . . . . . . . . . . . . . . .
5
SDTI input operations . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
SDTI output operations . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Precautions for using SDTI. . . . . . . . . . . . . . . . . . . . . . .
15
Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
Warning messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
Contents
4
$ Main unit
Dimensions (WtHtD):
6˝t5-7/8˝t13/16˝ (152t148t20 mm)
Weight:
0.5126 lb (233 g)
$ Video audio input connector
Serial digital input connector:
BNCt1
SDTI IN: Dedicated SDTI input connector
Compliant with SMPTE305M/SMPTE321M standards.
$ Video audio output connector
Serial digital output connector:
BNCt1
SDTI OUT: Dedicated SDTI output connector
Compliant with SMPTE305M/SMPTE321M standards.
Specifications
5
This board must be installed in the AJ-HD150 in order for it
to be used. Follow the procedure described below.
Installing the AJ-YAC150P board
1.
Disconnect the power cord from the main unit.
Consult your dealer before attempting to install the
digital video interface board.
The software versions for the VTR unit need to be
upgraded. Check to see if the proper versions are
running.
AV DV REC Ver.1.07 and up
DV PB Ver.1.03 and up
I/F Ver.1.04 and up
FRONT Ver.1.02 and up
SYSCON Ver.1.05 and up
SERVO Ver.1.03 and up
2.
Remove the two coin screws to remove the top panel
from the main unit.
Coin screws
6
Screws
Installing the AJ-YAC150P board
4.
Remove the nine screws to remove the rear panel.
<Note>
T
Exercise caution when handling the bundled wires
from the main unit side.
3.
Remove the two screws to remove the board clamp.
Screws
Board clamp
Screws
Connector clamp
Installing the AJ-YAC150P board
5.
Remove the two screws, then remove the connector
clamp on the rear panel.
6.
Pass the two coaxial cables through the holes in the
side of the slot marked “H2” on the main unit side to the
rear panel end.