Ozito AWG-964 User Manual
ARC
WHAT’S IN THE BOX
ONOVERLOAD
OFF
ONOVERLOAD
WELDER
140 Amp
INSTRUCTION MANUAL
SPECIFICATIONS
Input Voltage: 240V ~ 50Hz
Current Range: 55 - 130A
Peak Current: 140A
Duty Cycle: 25% @ 80 amp
Electrode Size: Ø2.0 - 3.2mm
ozito.com.au
OFF
Arc Welder
Arc Electrode Holder
Earth Clamp
Wire Brush / Chipping
Hammer
Welding Mask
AWG-964
WARRANTY
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: welding masks
and combination wire brush/chipping hammers.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
0814
KNOW YOUR PRODUCT
SETUP & PREPARATION
ARC WELDER
1 Carry Handle
2 Internal Cooling Fan
3 Overload LED
4 Current Setting Gauge
1
2
3
5 On/Off Switch
6 Current Regulator Knob
7 Electrode Holder
8 Earth Clamp
1. ASSEMBLY
WARNING: ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING STEPS.
Before starting you will require a suitable Electrode according to the
specic material type and thickness.
4
5
1 Install thin (uncoated)
end of Electrode into the
arc electrode holder.
6
WARNING: DO NOT TOUCH THE ELECTRODE WHILE
THE WELDER IS ON.
2 Attach the Earth Clamp
to the work piece
ensuring area is free
7
from paint or dirt so that
there is a good electrical
connection.
ACCESSORIES
9 Wire Brush / Chipping
Hammer
9 10
8
3 Connect the Arc Welder power
cord into a power outlet.
10 Welding Mask
NOTE: AVOID THE USE OF EXTENSION CORDS.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Loading...