box. Your experience of the universe
will soon be enhanced wirelessly and
powerfully. This manual exists to help
make sure that you use it correctly, so
you’re denitely going to want to relax
for a hot second and look through this.
Kisses,
ANATOMY
Power On / Power Off
Multi Function Button
Skip Backward / Volume Down
Skip Forward / Volume Up
Micro USB Charge Port / 3.5 mm Aux Port
USB Output Charge Port
Microphone
Light Indicator
POWER UP
TO CHARGE
For best results, fully charge your Turtle Shell®
3.0 before use!
1. Connect the included MIcro USB cord to a
power source and the charging port on the
Turtle Shell
light will stay activated. ***Full charge time
is about 4-5 hours.
2. When the Turtle Shell
the RED light will turn off.
The displayed battery meter is supported for
Apple products.
*The Turtle Shell® 3.0’s Bluetooth and music
functions can still operate while charging.
3.0. When charging, the red LED
®
3.0 is fully charged,
®
MUSIC FUNCTIONS
FUNCTIONBUTTONACTION
Answer an
incoming call
Reject an
incoming call
End callShort press once
Siri/Voice activation
Music / Device Controls
Skip backward
Volume down
FUNCTIONBUTTONACTION
Power onPress 3 sec
Power offPress 2 sec
Pairing modeHold for 3 sec
Manual pairing
mode
Play / PauseShort press once
Volume upShort press once
Volume downShort press once
Skip forwardPress & hold for
Skip backwardPress & hold for
MFB
Skip forward
Volume up
Hold for 3 sec
2 sec
2 sec
PHONE FUNCTIONS
Device Controls
Skip backward
Volume down
FUNCTIONBUTTONACTION
Answer an
incoming call
Reject an
incoming call
End callShort press once
Siri/Voice
activation
MFB
Skip forward
Volume up
Short press once
Press & hold for
2 sec
Press & hold for 2
sec & release
SINGLE PLAY SPEAKER PAIRING
Power On / Off
ON: Hold the Power Button for 2-3 seconds or until
the LED light flashes blue and the voice prompt
states “Power on”.
OFF: Hold the Power Button for 3-4 seconds or until
the LED light flashes blue and the voice prompt
states “Power off”.
Enter Pairing Mode
When powered on hold the “-” and “+” buttons
simultaneously for 2-3 seconds and you will hear
“Pairing” and the LED light will flash blue 3 times
then pause and repeat.
Pairing Turtle Shell 3.0 to Device
Open the Bluetooth settings on your device. If you
have put your Turtle Shell® 3.0 into pairing mode,
it should be listed as “ODT Turtle Shell® 3.0” as an
available device to pair. Connect with the Turtle
Shell® 3.0. The voice prompt will state “Paired”
when the Turtle Shell 3.0 and your device are
connected.
DUAL PLAY SPEAKER PAIRING
TS3 #1TS3 #2
STEP ONE
Turn on TS 3 #1 and wait until the voice prompt states
that the speaker is on. Then press & hold the “-” and
MFB buttons simultaneously. The Blue LED on the
TS3 #1 will ash 3X then pause and repeat when it’s
in speaker to speaker paring mode.
STEP TWO
Turn on TS3 #2 and wait until the voice prompt states
that the speaker is on. Then press & hold the “+” and
MFB buttons simultaneously. The Blue LED on the
TS3 #2 will ash 3X then pause and repeat when it’s in
speaker to speaker pairing mode.
STEP THREE
After a few seconds both the TS3 #1 and TS3 #2 will
state “Paired.”
STEP FOUR
Press & hold the “-” and “+” plus buttons simultaneously
for 2-3 seconds on TS3 #1. The blue LED will flash
3X then pause and repeat and state “paring” when
in speaker to device pairing mode. Open the
Bluetooth settings on your device and select ODT
Turtle Shell 3.0.
For more functions, go to outdoortech.com/apps
to download the Outdoor Tech app.
LISTEN CONTINUED
The built-in microphone means that the Turtle
Shell 3.0 can be used as a wireless headset.
*NOTE: The built-in microphone only works when
connected via Bluetooth.
The following are tips on how to use your Turtle Shell 3.0
to speak on the telephone:
Answer a call......... Press the multifunction button.
End a call............... Press the multifunction button.
Decline a call......... Press and hold the multifuntion
button for two seconds.
Make a call............ Use your phone to dial as usual.
Listen and talk through the
Turtle Shell® 3.0.
Mute...................... Hold the >> and << buttons for 2
seconds, or until you hear a beep.
FAQ
Hearing Distortion
A. Lower the volume on your Turtle Shell®
3.0® and / or phone /device.
B. Make sure it’s charged up. Check for
low battery, then charge if necessary.
Not Loud Enough
A. Turn up the volume on your phone /
device or your Turtle Shell® 3.0.
B. Make sure it’s charged up.
C. Plug the Turtle Shell in to your phone /
device via 3.5mm stereo cable.
Unable to Pair
A. Conrm your phone / device is Blue
tooth compatible.
B. Re-Pair: Follow pairing instructions in
this guide.
Signal Loss or Dropouts via Bluetooth
A. Move Turtle Shell closer to your phone
/ device.
B. Make sure it’s charged up.
C. Turn off your Turtle Shell® 3.0 and
phone / device, then power up and
reconnect.
SPECS
Rating: IPX7
Bluetooth v 4.2
Bluetooth Profiles: HSP, HFP. A2DP, AVRCP
Capatability: Bluetooth v 1.1 and above
Operating range: 32 ft
Operating range between speakers: 15 ft
Device name: ODT TURTLE SHELL 3.0
Power source: Lithium ion rechargeable
battery cell
Battery capacity: 3600mAh / 13.32 Wh
Charge Output: 5V / 1A
Charge Input: 5V / 2.1A
Playing Time: Up to 20 hrs
Charge Time: ~4.5 hrs
Operating Temperature: 0~45° C
Storage Temperature: -20~60° C
RoHS: Fully RoHS compliant