PSX-240-Relay
Enclosed Autotransformer
With Auto-Disconnect
Installation Manual
Outback Power PSX-240-Relay User’s Guide
Introduction
Congratulations on your purchase of the PSX-240-Relay Autotransformer with Auto-Disconnect from OutBack Power Systems. This booklet contains important safety and user instructions for the PSX-240-Relay that shall be followed during its installation and maintenance. Please read the entire booklet and all cautionary warnings on the PSX-240-Relay carefully before installing the device.
PLEASE SAVE THESE INSTRUCTIONS!
IMPORTANT SAFETY GUIDELINES
Working with or around electrical components requires care and special attention during installations. Shock, burns, equipment damage, fire and even death can result from mishandling or incorrectly installing electrical equipment. Please be aware of the following precautions:
•Installation must be performed by a licensed installer familiar with local and national wiring codes. All installations must comply with these codes as well as codes for structural installation.
•All of the AC wiring to the circuit breaker terminals and the neutral bus bar must be torqued according to the torque specs in the MECHANICAL INSTALLATION section of this manual.
•Wiring to circuit breaker terminals must meet requirements of the National Electric Code (NEC).
NOTE: The circuit breaker terminals will accept up to 10 AWG wire. Use copper conductors only with insulation rated for at least 75˚ C. See the WIRING CONNECTIONS AND TORQUE SPECS section of this manual for more information.
PSX-240-Relay User’s Guide |
Page 2 |
P/N: 900-0053-1 |
|
Rev. A – Released 12/19/2005 |
|
Outback Power PSX-240-Relay User’s Guide
REGISTRATION
Your purchase of an OutBack Power Systems product is an important investment. Registering your products will help us maintain the standard of excellence you expect from us in terms of performance, quality and reliability.
Please take a moment to register and provide us with some important information.
Name: __________________________________________
Address: ________________________________________
City, State, Zip Code, Country:
________________________________________________
Telephone Number: _______________________________
E-Mail: _________________________________________
Sold by: ________________________________________
Installer: ________________________________________
Purchase Date: ___________________________________
Model Number: ___________________________________
Serial Number: ___________________________________
Circle all that apply: |
|
Off-Grid Installation |
Residential Installation |
North America Location |
Utility Connected Installation |
Commercial Installation |
Other ____________________ |
Mail to: Attn: Warranty Registration
Outback Power Systems 19009 62nd Ave. NE
Arlington, WA 98223
PSX-240-Relay User’s Guide |
Page 15 |
P/N: 900-0053-1 |
|
Rev. A – Released 12/19/2005 |
|
Outback Power PSX-240-Relay User’s Guide |
Outback Power PSX-240-Relay User’s Guide |
• For equipment grounding hook up, see the WIRING CONNECTIONS AND TORQUE SPECS section in this manual. This product is intended to be installed as part of a permanently grounded electrical system per the NEC.
• The equipment ground on the PSX-240-Relay is marked with this symbol:
GENERAL PRECAUTIONS
• The PSX-240-Relay is approved for indoor mounting only in the positions described in the MECHANICAL INSTALLATION section of this manual.
• Do not disassemble the PSX-240-Relay beyond the instructions included in this manual. Refer servicing to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
• To reduce risk of electric shock, disconnect all wiring before attempting any maintenance or cleaning.
PSX-240-Relay User’s Guide |
Page 14 |
PSX-240-Relay User’s Guide |
Page 3 |
P/N: 900-0053-1 |
|
P/N: 900-0053-1 |
|
Rev. A – Released 12/19/2005 |
|
Rev. A – Released 12/19/2005 |
|
Loading...