Oster TF1600 Instruction Manual

MODEL/MODELO

Instruction Manual

16” TABLE FAN

PLEASE READ ALL INSTRUCTIONS BEFORE USING

Manual de Instrucciones

VENTILADOR DE MESA DE 40,6 CM

LEA TODAS LAS INSTRUCCIONES ANTES DE USAR

TF1600

TF1600

When using electrical appliances, basic safety precautions should always be followed to

reduce the risk of re, electric shock, and injury to persons, including the following:

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

• Use fan only for purposes described in the instruction manual.

• To protect against electrical shock do not immerse unit, plug or cord in water or spray
with liquids. Plug the appliance directly into an electrical outlet of the same voltage as
that of the rating plate in the unit.

• Close supervision is necessary when any appliance is used by or near children.

• Unplug from outlet when not in use, when moving fan from one location to another,
before putting on or taking off parts and before cleaning.

• Avoid contact with moving parts.

• DO NOT operate in the presence of explosives and/or ammable fumes.

• To avoid re hazard, NEVER place the cord under rugs or any parts near an open ame,
cooking or other heating appliance.

• DO NOT operate any appliance with a damaged cord or plug or after the appliance
malfunctions or has been damaged in any manner. Return this appliance only to the
nearest Authorized Oster

®

Service Center for examination, repair or adjustment.

• The use of attachments not recommended or sold by the appliance manufacturer may
cause hazards.

• DO NOT let the cord hang over the edge of a table, counter or come in contact with hot
surfaces or leave exposed to high trafc areas.

• DO NOT use outdoors.

• To disconnect, grip plug and pull from wall outlet. NEVER yank on cord.

• Always use on a dry, level surface.

• DO NOT operate fan until fully assembled with all parts properly in place.

• This product is intended for household use ONLY and not for commercial or industrial
applications.

• WARNING: To reduce the risk of electrical shock and injury to persons, DO NOT use in

window.

• WARNING: To reduce the risk of re or electric shock, DO NOT use this fan with any

solid-state speed control device.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFEGUARDS

1

Fig. 1

Fig. 2

4

8 7 5

36 2 1

Fig. 3

3

2

1

0

9

10

1. Oscillation Knob

2. Motor Assembly

3. Rear Guard

4. Guard Retaining Nut

5. Blade

6. Blade Retaining Nut

7. Shroud

8. Front Guard

9. Guard Locking Screw/Nut

10. Base

DESCRIPTION OF THE APPLIANCE

2

3

INSTRUCTIONS FOR USE

BEFORE USING FOR THE FIRST TIME

Read and follow all the instructions for this section on use and care and nd a place to keep
this instruction manual ready for future reference.

For your convenience, record the complete model number (located at the bottom of the
motor) and the date you received the product, together with your purchase receipt and
attach to the warranty and service information. Retain in the event that the warranty service
is required.

NOTE: The use of attachments not recommended or sold by Sunbeam Products, Inc. may
cause re, electrical shock, injury or damage to the product.

ASSEMBLY INSTRUCTIONS

1. Remove the plastic screw from the bottom of the motor assembly (turning counter­clockwise). Then attach motor assembly to base hole until snapped. Tighten screw to the
base. (see Figure 1).

CAUTION: The thumbscrew must be fully tightened before the fan is operated.

2. Remove the blade retaining nut (turning clockwise) while holding motor shaft. Remove
the guard retaining nut (turning counter-clockwise) while holding motor housing. Take off
the motor shaft sleeve protector and discard.

3. Set the rear guard in the proper position (carry handle up) on the motor assembly. Then
screw on the guard retaining nut (turning clockwise) until tight.

4. Install the blade onto the shaft of the motor assembly and screw on the blade retaining
nut (turning counter-clockwise while holding the blade) until tight.

5. Loosen, but do not remove the guard locking screw/nut. Place the shroud on the rear
guard with the guard locking screw/nut at the bottom. Assemble the front guard into
shroud so that all sides snap. Rotate the front guard until the Oster

®

logo is upright.

6. Secure both guards rmly by tting and tightening the guard locking screw/nut located at
the two ends of the shroud.

CAUTION: Do not over-tighten.