Oster SF1600 Instruction Manual
MODEL/MODELO
Instruction Manual
16” STAND FAN
PLEASE READ ALL INSTRUCTIONS BEFORE USING
Manual de Instrucciones
VENTILADOR DE PEDESTAL DE 40,6 CM
LEA TODAS LAS INSTRUCCIONES ANTES DE USAR
SF1600
SF1600
00SF1600-LA813_13ESM1.indd 1 4/3/13 4:50 PM
When using electrical appliances, basic safety precautions should always be taken
including the following:
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
• Use fan only for purposes described in the instruction manual.
• To protect against electrical shock do not immerse unit, plug or cord in water or spray
with liquids. Plug the appliance directly into an electrical outlet of the same voltage as
that of the rating plate in the unit.
• Close supervision is necessary when any appliance is used by or near children.
• Unplug from outlet when not in use, when moving fan from one location to another,
before putting on or taking off parts and before cleaning.
• Avoid contact with moving parts.
• DO NOT operate in the presence of explosives and/or ammable fumes.
• To avoid re hazard, NEVER place the cord under rugs or any parts near an open
ame, cooking or other heating appliance.
• DO NOT operate any appliance with a damaged cord or plug or after the appliance
malfunctions or has been damaged in any manner. Return this appliance only to the
nearest Authorized Oster® Service Center for examination, repair or adjustment.
• The use of attachments not recommended or sold by the appliance manufacturer may
cause hazards.
• DO NOT use outdoors.
• DO NOT let the cord hang over the edge of a table, counter or come in contact with
hot surfaces or leave exposed to high trafc areas.
• To disconnect, grip plug and pull from wall outlet. Never yank on cord.
• Always use on a dry, level surface.
• DO NOT operate fan until fully assembled with all parts properly in place.
• This product is intended for household use ONLY and not for commercial or industrial
applications.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFEGUARDS
1
00SF1600-LA813_13ESM1.indd 2 4/3/13 4:50 PM
DESCRIPTION OF THE APPLIANCE
2
Fig. 2
Fig. 3
Fig. 1
11
4
5
6
7 8 109 12 13 15
14
1. Height Adjustment Collar
2. Base
3. Base Securing Screw
4. Motor Housing
5. Oscillation Knob
6. Thumbscrew
7. Motor Shaft
8. Handle
9. Rear Guard
10. Guard Retaining Nut
11. Fan Blade
12. Blade Retaining Nut
13. Shroud
14. Guard Locking
Screw/Nut
15. Front Guard
1
2
3
00SF1600-LA813_13ESM1.indd 3 4/3/13 4:50 PM
BEFORE USING FOR THE FIRST TIME
Read and follow all the instructions for this section on use and care and nd a place to
keep this instruction manual ready for future reference.
For your convenience, record the complete model number (located at the bottom of the
motor) and the date you received the product, together with your purchase receipt and
attach to the warranty and service information. Retain in the event that the warranty
service is required.
NOTE: The use of attachments not recommended or sold by Sunbeam Products, Inc.
may cause re, electrical shock, injury or damage to the product.
ASSEMBLY INSTRUCTIONS (see Figure 1)
1. Attach the lower pole to the base, insert the base securing screw and tighten the
screw into the base. Make sure to align the slot on the lower pole with the rib on the
base.
2. Pull out the inner extension tube and ret/tighten the collar. CAUTION: The collar
must be fully tightened before assembling the motor section to the pedestal
stand.
3. Loosen the thumbscrew on the rear of the motor assembly. Fit the motor assembly to
the inner extension tube and tighten the thumbscrew. CAUTION: The thumbscrew
must be fully tightened before the fan is operated.
4. Remove the blade retaining nut (turning clockwise) while holding motor shaft. Remove
the guard retaining nut (turning counter-clockwise) while holding motor housing. Take
off the motor shaft sleeve protector and discard.
5. Set the rear guard in the proper position (carry handle up) on the motor assembly.
Then screw on the guard retaining nut (turning clockwise) until tight.
6. Install the blade onto the shaft of the motor assembly and screw on the blade retaining
nut (turning counter-clockwise while holding the blade) until tight.
7. Loosen, but do not remove the guard locking screw/nut from shroud. Place the shroud
on the rear guard with the guard locking screw/nut at the bottom. Assemble the front
guard into shroud so that all sides snap. Rotate the front guard until the Oster® logo is
upright.
8. Secure both guards rmly by tting and tightening the guard locking screw/nut located
at the two ends of the shroud. CAUTION: Do not over-tighten.
INSTRUCTIONS FOR USE
3
00SF1600-LA813_13ESM1.indd 4 4/3/13 4:50 PM
Loading...