Orion TV32LB2000(H), TV42LB2000(H), TV46LB2000(H) Operating Instructions Manual

Operating Instructions

Before operating the unit, please read this manual thoroughly.

100Hz LED-TV

Model-No.:

TV32LB2000(H)
TV42LB2000(H)
TV46LB2000(H)

TV32LB2000H
TV42LB2000H
TV46LB2000H

3DH0114B_EN.indd 13DH0114B_EN.indd 1 5/12/11 9:45:35 AM5/12/11 9:45:35 AM

2

Features

Headphone Warning

Loud music can damage your hearing irreversibly, therefore do not set the volume to a high level when
listening through headphones, particularly for extended listening periods.

Battery notice (valid in EU only)

Look after our environment - contact your local authorities for advice on how to safely dispose of exhausted
batteries. The crossed out wheelie bin symbol indicates that used batteries should not be disposed of
with your normal household waste! A separate collection system for used batteries is in place to allow the
correct treatment and recycling in accordance with current legislation. Please contact your local authority for
details on collection and recycling schemes in your area.

DVB-C notice

The DVB-C reception possibly requires an additional contract with your cable supplier. A Smartcard
for the receipt of encrypted programmes comes with the contract. Programmes that do not come with the
contract will remain encrypted and not be viewed.
You receive DVB-C programmes with a CAM module of your cable network operator. You insert the CAM
module into the CI-Slot (refer to page 10) of this TV set. You insert the Smartcard into the CAM
module.
You can possibly receive a few unencrypted DVB-C programmes at your home location even without an
additional contract and without a CAM module. However, these programmes frequently reveal a poorer
image quality than the DVB-C-HD programmes that are subject to a charge. The image quality that is
frequently poor is a feature of the respective programmes.

Information for the DVB-T function

Any function relative to the digital television (with the DVB logo) is available only within the country or area
where such signals are transmitted. Verify with the salesman if it is possible to receive a DVB-T signal in
the zone where you live.
A DVB-T antenna must be connected for DVB-T reception.
Even if the television conforms to the DVB-T specifications, the compatibility to future digital DVB-T
transmissions is not guaranteed.
Some digital television functions may not be available in some countries.
The DVB-T system present in this device is FTA (Free to air).

Waste Disposal Tip

This symbol means that your electrical and electronic equipment should be disposed at the
end of its life separately from your household waste. There are separate collection systems
for recycling in the EU. For more information, please contact the local authority or your retailer
where you purchased the product.

•

•

•

•

•

•

•

•

100Hz-16:9-FullHD-LED-TV
Panel-Resolution: 1920 x 1080
DVB-C-HDTV-Tuner with CI(+)-slot
D V B -T-Tuner
Cable-analogue-Tuner
7-band Equalizer
Sensorkeys on TV-unit

•

•

•

•

•

•

•

Mechanical mains switch for 0.0W power
consumption

Auto Power Off after 4 hours with no
operation

•

•

Equipment connected to the protective earthing of the building installation through the mains connection
or through other equipment with a connection to protective earthing – and to a cable distribution system
using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution
system has therefore to be provided through a device providing electrical isolation below a certain fre­quency range.

Utstyr som er koplet til beskyttelsesjord via nettplugg og/eller via annet jordtilkoplet utstyr – og er tilkoplet
et kabel-TV nett, kan forårsake brannfare.
For å unngå dette skal det ved tilkopling av utstyret til kabel-TV nettet installeres en galvanisk isolator mel­lom utstyret og kabel-TV nettet.

Utrustning som är kopplad till skyddsjord via jordat vägguttag och/eller via annan utrustning och samtidigt
är kopplad till kabel-TV nät kan i vissa fall medföra risk för brand.
För att undvika detta skall vid anslutning av utrustningen till kabel-TV nät galvanisk isolator finnas mellan
utrustningen och kabel-TV nätet.

3DH0114B_EN.indd 23DH0114B_EN.indd 2 5/12/11 9:45:38 AM5/12/11 9:45:38 AM

3

Contents

* DVB and the DVB logos are trademarks of the DVB project.
* Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks

of Dolby Laboratories. (TV32...H/TV42...H/TV46...H)

* THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PER-

SONAL AND NON-COMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE
WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED
BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS
GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE

OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM
*
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks

of HDMI Licensing LLC in the United States and other countries.

Viewing distance

Your new FullHD-TV has been designed to display high-resolution HD-signals in the very best quality.
Currently the following HD-sources are available:

1. DVB-S2-HDTV satellite receiver

2. HDTV cable receiver

3. Blu-ray player.

Only above sources offer highest-quality HD-video at top-resolution, which your new FullHD-TV lets you enjoy
now. To play such signals at full resolution, it is necessary to connect the sources by HDMI-cable (not supplied).
The recommended closest viewing-distance for such HD-signals is: 1 meter. You may also watch from greater
distance, however you might not catch all the HD-video’s details.

Standard video

All other sources offer standard-resolution of max. 576 lines, e.g. analog & digital cable-TV, MPEG-2-DVB-T, DVB­S-satellite receiver, DVD-Player, VHS, etc.
For all 16:9-videos the analog cable-TV transmits only 432 lines. For comparison: HD-sources deliver 1080
lines. Having more than twice the amount of lines, the HD-video looks a lot more detailed compared to analog
TV. Or vice versa: analog video supplies a very poor quality if viewed on FullHD-TVs. Thus the recommended
closest viewing-distance for analog cable-TV is: 3,00 meters. You may watch from a greater distance though.
If, however, you decide to watch such poor signal from a distance closer than recommended, you will notice the
signal’s inherent poor quality.

How to improve the analog cable-TV’s picture-quality.

Actually analog cable has a 60-year history and is now quite old-fashioned. Cable supplier will not improve the
analog-video-standard any more. However, you may upgrade to digital-cable-qualtiy for relatively low cost. Please
ask your cable-supplier for more detail concerning the low-cost trial-period, free digital receiver, etc.

Features .........................................................2

Contents ........................................................3

Important safety information...........................4

Location of controls ........................................7

Remote Control ..............................................8

Antenna connection .....................................10

Auto setup....................................................11

Selecting the input source ............................12

On-screen Language Selection ...................12

Automatic channel scan ...............................12

Manual channel scan ...................................12

Channel list setting ......................................12

Basic Operation ...........................................13

Teletext ........................................................14

Remarks on DVB-T system ..........................15

Password Setup (Parental lock) ...................16

EPG (Electronic Program Guide) .................16

Picture size and resolution ...........................17

Picture format...............................................18

Other convenience functions .......................19

Media Operation ..........................................22

Media Browser .............................................22

Playable File Types ......................................23

PC connection .............................................24

Connecting an HDMI

or a DVI device to the

HDMI input ...................................................24

Connection to other equipment ....................25

Troubleshooting table ...................................27

Specifications ..............................................27

3DH0114B_EN.indd 33DH0114B_EN.indd 3 5/12/11 9:45:39 AM5/12/11 9:45:39 AM

4

Important safety information

This unit has been produced according to all current safety regulations. The following safety tips should safeguard
users against careless use and the dangers connected with such use.

Although this appliance has been carefully manufactured and rigorously checked prior to leaving the factory, as
with all electrical appliances it is possible for problems to develop. If you notice smoke, an excessive build-up
of heat or any other unexpected phenomena, you should disconnect the plug from the mains power socket
immediately.
Ensure that the unit is sufficiently ventilated! Never place next to or underneath curtains!
This set should be only be connected to an AC 220~240V / 50Hz mains power supply - do not attempt to
connect it to any other type of supply.
The apparatus must be connected to a main socket outlet with a protective earthing connection.
The socket-outlet must be installed near the equipment and easily accessible.
Any repairs must be carried out by qualified service personnel only.
Do not open this unit. A non-expert attempting to repair the unit could be dangerous and potentially cause a fire
hazard.
Keep away from rodents. Rodents (and also cockatiels) enjoy biting into electric flexes.
The animal can cause a short cut (fire hazard!) and receive a fatal electric shock.
Always hold plug when pulling out plug from power mains supply system. Do not pull on flex. The flex can
become overloaded and cause a short cut.
Never wet clean. Only use a damp cloth, the same as when cleaning furniture.
Do not submerge in or under water!
Set up unit so that no one is able to trip over the flex.
This unit is recommended to be installed on shock-free benches in order to avoid any danger from falling.
Take note that toddlers can pull the unit down from the table or cupboard by means of its flex. Children can hurt
themselves when doing this.
Do not use the unit near heat sources. The casing and flex could be damaged by the impact of heat.
Watch out for kiddies copying what adults do! Do not stick any objects through the vents!
The vents must remain open! No newspapers or covers should be put on the unit!
The remote control is not a toy! Toddlers could swallow the batteries. If a battery has been swallowed, please
seek out a doctor immediately.
The screen is made of glass and can break if damage is done to it. Be careful when collecting sharp-edged
glass splitters.
You could be hurt or the unit could be damaged.
If the unit is mounted on the wall, contact the shop where you purchased the unit for advice, and leave the
installation work to experts. Incomplete installation work can cause you injuries.
Taking fall-prevention measures

- If these measures are not taken, the unit can fall and you could be injured.

- Contact the shop where you purchased the unit to obtain full details of the measures.
When a TV stand is used,

- Ensure the unit is fully on the stand and placed in the centre.

- Do not leave the stand doors open.

- You could be hurt as a result of the unit falling or breaking, or your fingers being caught or jammed. Take extra
precautions if you have children.

Avoid placing the unit on any surfaces that may be subject to vibrations or shocks.
To protect the unit during a thunder storm unplug the AC power cord and disconnect the antenna. Caution: Do
not touch the antenna connector.
When you leave your home for a long period of time, unplug the AC power cord for safety reasons.
The unit becomes warm when in operation. Do not place any covers or blankets on the unit in order to prevent
overheating. The ventilation holes are not to be blocked. Do not set up near radiators. Do not place in direct
sunshine. When placing on a shelf leave 10 cm free space around the whole unit.
Make some space around TV (Correct shelf assembly).
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
Liquids spilled into the unit can cause serious damage. Switch the set OFF and disconnect the mains power
supply, then consult a qualified service person before attempting to use the unit again.

Please pay attention to the following instructions in order to avoid receiving a life-threatening electric
shock:

Protect against moisture. Never use in the bath or sauna.
Never use near a bath, shower or swimming pool.
Never use the unit if it has got wet. This can also mean condensation moisture, which occurs in the winter when
the cold unit is brought into a heated flat. Wait before operating the unit especially after it has been transported
in the winter, until the cold unit has adjusted to the room temperature.
Do not place any heavy objects on the flex. Electrical isolation could be damaged.
Never wrap insulating tape around damaged flexes or on damaged plugs. These should be repaired or replaced
by qualified service personnel.
Never use this unit if the cabinet is defective. Do not make provisional repairs if the cabinet is damaged - this
should be replaced by a new cabinet if necessary.
Unplug the unit from the mains power supply prior to the cleaning of the unit.

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

3DH0114B_EN.indd 43DH0114B_EN.indd 4 5/12/11 9:45:39 AM5/12/11 9:45:39 AM

5

Important safety information

How to attach the stand

NOTE:

• Unplug the AC cord from the AC Outlet terminal.

• Before beginning this process, assure that TV is laid on a clean, safe, and cushioned space to avoid any
damage to the unit.

• Do not touch or press the TV-screen, glass might break under pressure.

• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.

1) Place the TV on its front onto a table.

2) Align the stand’s bottom-plate (supplied) as seen here.

It will fit in only one direction.

3) Hold the unit and attach the stand slowly. Finally secure the bottom-plate with screws(included).

Dismantling the base

For wall mounting, the base must be dismantled. To do this, remove screws (N, see page 10) from the back.
Take off the base entirely.

NOTE:

To detach the stand, perform these steps in reverse order.•

TV32...

TV42... / TV46...

Warning (TV46...)

To prevent injury, this apparatus should be securely attached to the floor/wall in accordance with
the installation instructions.

1.

Please use two strong strings of the same length as distance (A) between the back of the unit and the wall.

2. Please tie the string to the place in the figure below.

A

Screw

Clamp

String

String

3DH0114B_EN.indd 53DH0114B_EN.indd 5 5/12/11 9:45:40 AM5/12/11 9:45:40 AM

6

WARNING

To prevent fire, never place any type of candle or open flame
on the top or near the TV set.

Moving the unit or carrying by hand

When the unit is moved a long way, unplug the power cord and disconnect the antenna, connecting
cables and any fall-prevention apparatus.

• Moving without doing so could result in damage to the power cord, a fire, electric shocks or injuries from
dropping the unit.

Ensure that unpacking and transfer of the unit is carried out by two or more people and that the unit
stays upright when doing this.

When the TV stand has casters, remove caster cups from the stand and push it while supporting the
unit.

• Ensure that you support the unit when the stand is pushed, as this can cause the unit to fall and you could
be injured.

• The appliance could leave indentations in wooden tables with extremely soft wooden surfaces due to its
heavy weight.

• Furniture polish could corrode and dissolve rubber feet. Black imprints could be visible on the table. You
should therefore only use TV benches, which have been constructed for this specific purpose.

Secure the casters when the unit is installed on a TV stand with casters.

• The stand can move and you could be hurt if the casters are not secured.

Remove casters when the stand is placed on a soft surface such as a mat and carpet.

The distance between eyes and the screen should be about 3 ~ 4 times as long as height of the screen.

• Viewing from too close a distance can cause strain for your eyes.

When installing the Monitor on a table, be careful not to place the edge of its stand.

• This may cause the Monitor to fall, causing serious injury to a child or adult, and serious damage to the
Monitor.

Possible Adverse Effects on LCD Screen: If a fixed (non-moving) pattern remains on the LCD screen for long
periods of time, the image can become permanently engrained in the LCD TV panel and cause subtle but perma­nent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. Never leave your TV on for
long periods of time while it is displaying the following formats or images:

• Fixed Images, such as stock tickers, video game patterns, TV station logos, and websites.

• Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on a normal
(4:3) display (Black bars at top and bottom of screen); or viewing normal style (4:3) media on a widescreen
(16:9) display (Black bars on left and right sides of screen).

Attention!

Cleaning instructions for your LCD TV.

Safety note:

Before you start to clean, switch the set’s power off completely and disconnect the plug from the mains power supply.
Be careful not to scratch the plastic coated front panel - it is highly vulnerable to accidental scratching (e.g. by

fingernails or other sharp items). (While cleaning, do not wear jewelry) that could cause surface scratching (such
as rings, wrist-watch, etc.). Use a lint-free cloth and pure water to clean with, but make sure the cloth is thoroughly
wrung out so that it is just damp and not soaking wet - also make sure that the cloth is free from any dirt that could
cause scratching to the surface.
Wipe the set clean using minimal pressure.
Do not use standard window cleaning fluid. Its alcohol / ammonia will dissolve the front window’s coating.
Never use solvent or thinner. Never use special cleaners which are designed for cleaning PC Monitors or CRT TVs.
Finally carefully rub dry with a clean dry lint-free cloth.
Do not use paper towels or tissues to clean the set - paper can disintegrate when wet or may leave a trail of dust
behind. Some paper can also be abrasive and scratch your screen.

Saving electricity

The backlight’s brightness (power) can be set manually to match the surrounding illumination. At bright daylight
the backlight’s full power is required to perform a brillant result. During lower illumination, e.g. at night, you set
a lower backlight-brightness (see p. 21). Figures lower than 10 reduce the brightness, save energy and offer
a dazzlefree fatigueless watching at night.

•

Important safety information

3DH0114B_EN.indd 63DH0114B_EN.indd 6 5/12/11 9:45:44 AM5/12/11 9:45:44 AM

7

Location of controls

Description of Indicators and Controls

1. Loudspeakers

2.

(Standby/On) indicator: The LED indicator lights up red in standby mode, and blue in the power

ON mode.

3. Remote sensor

4.

(Power)-key: Enter standby mode or turn on the power. Preparation: Connect power-cable to

AC220~240V/50Hz. Then turn on mains switch (9).

5. INPUT/ENTER button: Select input mode for TV/AV/COMPONENT/HDMI/PC. In Menu : Using as
ENTER button.

6. MENU button: To display the menu screen.

7. P (Channel) +/–/▲/▼ buttons: Press + to change to a higher numbered channel set into memory.
Press – to change to a lower numbered channel set into memory. In Menu: Setting.

8.

(Volume) +/–/◀/▶ buttons / In Menu: Setting.

9.

Mains switch: Switch on/off power supply completely.

For complete disconnection from the mains power supply, remove the supplied power cable from the
socket.

To adjust the TV angle (TV42.../TV46...) :

You can adjust the TV angle of the TV-screen for 30° from horizontal angle. Hold the base of the TV while
adjusting the angle.

51678

3

4

2

9 (TV42.../TV46...)9 (TV32...)

3DH0114B_EN.indd 73DH0114B_EN.indd 7 5/12/11 9:45:45 AM5/12/11 9:45:45 AM

8

Remote Control

Function Page
Enter standby mode or turn on the power 11

Display program information 13

Select an input source 12

Select picture format 18

Select channel
Select Teletext page
Enter password

13
14
16

Select between the available broadcast
audio

13

Display the EPG (Electronic Progr. Guide) 16

Activate menu 11

In menu, return 1 step / exit menu

Cursor buttons

Memorize
Channel List 13

Turn the sound on/off 13

Display the subtitle 13

Volume

Still picture
Hold the text page

13
14

Switches between the present channel and
the last selected channel
Sub Page selection

13
14

Change the TV channel or Teletext page up
or down

13

Teletext ON / TV+text / OFF 14

Reveal quiz page answers 14

Teletext enlargement 14

Sort channel 13

To enter Media Browser

22

This button is not effective to this product

Control buttons for USB - playback 22
Fastext/TOPtext buttons 14

3DH0114B_EN.indd 83DH0114B_EN.indd 8 5/12/11 9:45:45 AM5/12/11 9:45:45 AM

9

Remote Control

Install the batteries

Use batteries type UM4 (AAA-Size).
Do not use old or weak batteries. The remote control may not work properly with a weak voltage from such
batteries. Replace exhausted batteries with new ones. Never try to recharge normal batteries - this could
cause an explosion.

Note:

Exhausted batteries can leak corrosive electrolyte, which may cause damage to the remote
control - therefore remove exhausted batteries immediately.
Batteries should not be exposed to excessive heat such as sunshine, fire or the like.

1

Open the battery
compartment.

2

Install the batteries as shown
below, ensuring the correct
polarity.

3

Close the battery
compartment.

•

•

The remote control handset will not work properly in the following cases:

a) If bright sunlight directly beams onto the unit front. b) If an obstacle is placed between the unit and the

handset.

Z

Z

Z

Z

Z

Z

c) If the batteries have not been installed

according to their polarities.

d) If the batteries are weak.

Distance of Remote Control Operation

Transmitter window

Maximum distance approx. 5m

Remote sensor

Point the remote control
directly at the remote sensor.

30 30

3DH0114B_EN.indd 93DH0114B_EN.indd 9 5/12/11 9:45:49 AM5/12/11 9:45:49 AM