Orion OLMU-K4650, OLMU-K5550, OLMU-K4670, OLMU-K5570 User Manual

Download

Page 1

A revolutionary MLCD

Infinitely Expandable MLCD

ORION CO.,LTD.

www.oriondisplay.net

Address: 217, 1gongdan-ro, Gumi-si, Gyeongsangbuk-do, Korea

Tel : +82-2-6678-8533, Fax: +82-2-6678-8599

OLMU-K4650|OLMU-K4670|OLMU-K5550|OLMU-K5570

User's Manual

please read through this user's manual for safety before installing this product

2018.03.13

Page 2

Features

▶ Enjoy a wide flat screen with high brightness and high quality. ▶ Easy to install and move due to its thin design ▶ Enjoy your favorite programs with various split-screen features simultaneously presenting

several programs.

Thank you for purchasing our monitor.

This manual describes how to use the product and notes in use. Please read the manual carefully before using it. After reading this manual, please retain for future reference.

If you have any questions or a problem occurs, please contact either the company you purchased this product from or an authorized service center.

※Displaying static picture for an extended period of time may cause an burn-in effect. ※Burn-in effect and the faults in brightness and picture elements caused by fixed images are not

subject to the warranty coverage.

Warning

If you fail to comply with the regulations for safety and proper use, fire or injury may be caused.

Class A digital device

Innitely Expandable

Notice to users

MLCD

It is a device designed for business purpose with a safety certificate for electromagnetic interfere nce, which user should be mindful of.

" Important Safety Instructions"

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

To prevent electric shock, Do not remove cover.

Warning

No user serviceable part inside. Refer servicing to qualified service personnel.

Supplied Accessories

User's manual CD

RS-232C Cable Remote Controller Battery (AAA X2) IR Receiver

Guide Pin(4pcs)

Optional Accessories

Power Cable

DP Cable

f M o

1 2 3

ut e Ti m

4 5 6

er BC

7 8 9

Off

DIC

AD Prog.

og.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. The symbol in figure 21 shall be shown adjacent to the text of item 12 above.

MAIN FRAME

FCC Verified : Class "A"

This device complies with the Part 15 of the FCC Rules.Operation is subject to the following two c onditions :

1) This device may not cause harmful interference, and 2) This device must accept any interf erence received, including interference that may cause undesired operation.

- 1 -

Page 3

www.oriondisplay.net

Contents

Innitely Expandable

MLCD

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.

NOTICE

1. To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable

2. WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture.

3. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

4. Use only a properly grounded plug and receptacle

5. "Warning" CAUTION – These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

※European Union Disposal Information ............................................................................................

※Cautions for consisting ...................................................................................................................

※Clearance for Ventilation ................................................................................................................

※Cleaning and Maintenance..............................................................................................................

※Please keep following instruction for panel protection without exception........................................

※Handle with Caution ........................................................................................................................

※How to carry.....................................................................................................................................

※Application information ....................................................................................................................

※Attention for Installing .....................................................................................................................

1. Safety Precautions...........................................................................................................

2. Names...............................................................................................................................

3. How to Connect Cables..................................................................................................

3.1. Connection of Single.................................................................................................................

3.2. Connection of Multiple (for DP in).............................................................................................

3.3. Connection of Multiple (for HDMI in)........................................................................................

3.4. Connection of Multiple (for DVI in)............................................................................................

3.5. Connection of Control Cable....................................................................................................

4. ID Setting..........................................................................................................................

4.1. Sequential Connection.............................................................................................................

4.2. Random Connection.................................................................................................................

5. OSD Menu.........................................................................................................................

5.1. Picture Menu.............................................................................................................................

5.2. Input Menu................................................................................................................................

5.3. Schedule Menu.........................................................................................................................

5.4. Multi-Display Menu...................................................................................................................

5.5. Other Menu...............................................................................................................................

5.6. Information Menu.......................................................................................................................

6. Setting and operation of OSW.......................................................................................

6.1. Installation.................................................................................................................................

6.2. Start OSW................................................................................................................................

6.3. Communication Configuration..................................................................................................

6.4. Screen Configuration................................................................................................................

6.5. Explanation of the command transmission method..................................................................

6.6. Basic Control............................................................................................................................

6.7. Control......................................................................................................................................

..42

..50

..55

7. PROTOCOL.......................................................................................................................

7.1. Communication Setting.............................................................................................................

7.2. Protocol Format.........................................................................................................................

7.3. Command.................................................................................................................................

..68

8. Before calling for service................................................................................................

9. Applicable signals............................................................................................................

10. Specification…...............................................................................................................

11. Regulatory Information.................................................................................................

12. Dimension.......................................................................................................................

12.1. OLMU-K4650/OLMU-K4670...................................................................................................

12.2. OLMU-K5550/OLMU-K5570...................................................................................................

…4 …5 …6 …7 …8

…9 ..10 ..11 ..12

.14

.16

.18

.20 ..21 ..22 ..23

.26

..26 ..28

.32

..32 ..33 ..34 ..35 ..36 ..37

.38

..38 ..39

..49 ..50

. 66

..66

..67

. 72

.74

.75

. 76

..76 ..77

- 2 -

- 3 -

Page 4

www.oriondisplay.net

Innitely Expandable

MLCD

※

European Union Disposal Information

English

Disposal of old Electrical & Electronic Equipment (Applicable th

WARNING

roughout the European Union and other European countries wit h separate collection programs)

This symbol found on your product or on its packaging, indicates that this prod uct should not be treated as household waste when you wish to dispose of it. In stead, it should be handed over to an applicable collection point for the recyclin g of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environm ent and human health, which could otherwise be caused by inappropriate dispo sal of this product. The recycling of materials will help to conserve natural resour ces.

Mise au rebut des équipements électriques et électroniques usagé s (Valable dans l’ensemble de l’Union Européenne ainsi que dans le s pays européens disposant de programmes distincts de collecte des déchets)

Ce symbole appliqué sur votre produit ou sur son emballage indique que ce produit ne doit pas être traité comme un déchet ménager lorsque vous voulez le mettre au rebut. Il doit au contraire être remis à un site de collecte agréé pour le recyclage des équipe ments électriques et électroniques. En veillant à ce que ce produit soit mis au rebut de façon adéquate, vous contribuerez à prévenir les conséquences potentiellement négatives sur l’environnement et sur la santé humaine qui risqueraient de se produire en cas de mise au rebut inappropriée de ce produit. Le recyclage des matéri aux contribuera également à économiser les ressources naturelles.

Français

Entsorgung von elektrischen & elektronischen Altgeräten (geltend f ür die europäische Gemeinschaft und andere europäische Länder mit separaten Sammelprogrammen)

Dieses Symbol, zu finden auf Ihrem Produkt oder dessen Verpackung, macht Sie darauf aufmerksam, dass dieses Produkt bei der Entsorgung nicht als Ha usmüll behandelt werden darf. Statt dessen sollte es an eine Sammelstelle zu m Recycling von elektrischen und elektronischen Altgeräten gegeben werden. Helfen Sie mit, potenziell schädliche Einflüsse auf Umwelt und Gesundheit, die durch eine unsachgemäße Entsorgung d ieses Produktes entstehen können, zu vermeiden und entsorgen Sie dies es Produkt ordnungsgemäß. Recycling hilft, natürliche Rohstoffe einzuspa ren.

Deutsch

※

Cautions for consisting

Environmental condition for installation

- Since monitor is very sensitive for physical impact, installation requires considerable caution.

- Minimum clearance(20cm) must be secured for smooth ventilation. (See page 6) Installation must avoid air tight or near air tight places. Improper ventilation causes malfunction and

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your loc al authorities or dealer and ask for the correct method of d isposal.

Español

Deshecho de equipos eléctricos y electrónicos (aplicable a la Unión Europea y a otros países europeos con programas de r eciclaje independientes)

La presencia de este símbolo en el propio producto o en su material d e embalaje, indica que no se debe tratar como residuo doméstico cuando desee deshacerse de él. En su lugar, debe entregarlo en el punto limpio correspondiente de reciclaje de equipos eléctricos y electrónicos. Asegurándos e de que este producto se desecha de forma correcta, ayudará a evitar posible s consecuencias negativas para la conservación del medioambiente y la salud humana, consecuencias que podrían darse si se deshace del producto de form a inadecuada. El reciclado de materiales ayuda a conservar los recursos natura les.

Este símbolo solamente es válido en la Unión Europea. Si desea deshacerse de este producto, póngase en contacto con las autoridades locales o con su distri buidor y pida información sobre el método de dispo sición adecuado.

Português

Eliminação de equipamentos eléctricos e electrónicos usados ( aplicável na União Europeia e noutros países europeus com pr ogramas próprios de recolha destes equipamentos)

Este símbolo, colocado no produto ou na respectiva embalagem, indica que o produto não deve ser tratado como lixo doméstico aquando da sua elimina ção. Em vez disso, deve ser entregue num ponto de recolha de quipamentos eléctricos e electrónicos para posterior reciclagem. Ao garantir a correcta elimi nação deste produto, estará a evitar consequências potencialmente negativas tanto para o ambiente como para a saúde humana. A reciclagem de materiais ajuda a preservar os recursos naturais.

Este símbolo apenas é válido na União Europeia. Se quiser eliminar este produto, contacte as entidades l ocais ou o seu fornecedor para ficar a saber qual o método de eliminação correcto.

Ce symbole n’est valable que dans l’Union Européenne. Si vous souhaitez mettre ce produit au rebut, veuillez pre ndre contact avec les autorités locales ou avec votre reve ndeur et renseignez-vous sur la méthode de mise au reb ut correcte.

Italiano

Smaltimento delle attrezzature elettriche ed elettroniche usate ( applicabile in tutta la Comunità Europea ed altri Paesi Europei c he applicano programmi di raccolta differenziata)

Il simbolo trovato sul prodotto, o sulla sua confezione, indica che il prodotto n on può essere trattato come i domestici quando è il momento di smaltirlo. Al contrario, deve essere consegnato ad un centro di raccolta specializzato nel r iciclaggio di attrezzature elettriche ed elettroniche. Assicurando che il corretto smaltimento di questo prodotto, si aiuterà a prevenire potenziali conseguenze negative sull’ambiente e sulla salute umana, che possono essere provocate da uno scorretto smaltimento di questa attrezzatura. I materiali riciclati aiutera nno a conservare le risorse naturali.

Questo simbolo è valido solo nell’Unione Europea. Per smaltire questo prodotto, mettersi in contatto con le a utorità locali – o con il rivenditore – e chiedere informaz ioni sul corretto metodo di smaltimento.

Polski

Usuwanie zużytego sprzętu elektrycznego i elektronicznego (Dot yczy krajów Unii Europejskiej i innych krajów europejskich z oddz ielnymi programami zbiórki odpadów)

Obecność tego symbolu na produkcie lub na opakowaniu z produktem ozn acza, że tego produktu nie można wyrzucać razem z odpadkami domowym i. Należy go przekazać do punktu zbiórki w celu poddania recyklingowi podz espołów elektrycznych i elektronicznych. Usunięcie tego produktu w prawidł owy sposób, pomoże w zabezpieczeniu przed negatywnym wpływem odpa dów na środowisko i zdrowie ludzi, powodowanym przez niewłaściwe usuw anie produktu. Przetwarzanie materiałów pomaga w zachowaniu zasobów n aturalnych.

Ten symbol obowiązuje wyłącznie w krajach Unii Europejskiej. Informacje dotyczące prawidłowej metody usunięcia t ego produktu, można uzyskać u władz lokalnych lub u dostawcy.

Verwijderen van oude elektrische en elektronische apparatuur (t oepasselijk in de volledige Europese Unie en andere Europese la nden met afzonderlijke programma’s voor afvalverzameling)

Dit symbool dat op het product of zijn verpakking is aangebracht, geeft aan dat dit product niet mag worden behandeld als huishoudelijk afval als u het wilt we gwerpen. U moet het afgeven bij een specifiek verzamelpunt voor de recyclage van elektrische en elektronische apparatuur. Door te garanderen dat u dit prod uct op de correcte manier wegwerpt, helpt u potentiële negatieve gevolgen vo or het milieu en de menselijke gezondheid, die zouden kunnen worden veroorz aakt door een onrechtmatig wegwerpen van het product, te voorkomen. De re cyclage van materialen helpt het behoud van natuurlijke bronnen.

Waste Electrical and Electronic Equipment (WEEE) Directive In th e European Union, this label indicates that this product should not be disposed of with household waste. It should be deposited at a n appropriate facility to enable recovery and recycling. EEE compl ies with Directive ‘Regulation on the Restriction of the Use of Cert ain Hazardous Substances in Electrical and Electronic Equipment’

Dieses Symbol ist nur innerhalb der europäischen Gemeinschaft gültig. Wenn Sie dieses Produkt entsorgen möchten, wenden Sie sich bitte an Ihre örtliche Behörde und fragen Sie na ch der ordnungsgemäßen Entsorgungsmethode.

Nederlands

Dit symbool is alleen geldig in de Europese Unie. Als u dit product wenst weg te gooien, dient u contact op t e nemen met uw lokale instanties voor details over de gep aste methode voor afvalverwijdering.

Waste Electrical and Electronic Equipment(WEEE) Directi ve In the European Union, this label indicates that this pr oduct should not be disposed of with household waste. It should be deposited at an appropriate facility to enable r ecovery and recycling. EEE complies with Directive ‘Reg ulation on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment’

shortens product lifetime by rapid internal temperature rise. If monitor has to be installed with the improper ventilation, additional ventilation openings or fans must be provided to keep the internal temperature between 0 ~ 35˚C.

- For ground of monitor and application devices, it should be connected as frame ground.

- Considering monitor Max power consumption, check the main electric specification .

Recommended Operating Condition

- Temperature: 5~35˚C, Humidity: 35~75%, Suitable operating time : under 18 hours a day.

- Do not install the set at the air-tight condition.

- It is recommended to install the set with good ventilation.

- Do not install the set at the place of direct sunlight or excessive exposure to lightings.

※ Blackening, stains or burning effect on the screen can be occurred by improper

installation or use against the above recommended conditions.

WARNING

Svenska

Avfall av förbrukad elektrisk och elektronisk utrustning (Tilläm pbart i hela Europeiska unionen och andra europeiska länder med separata samlingsprogram)

Den här symbolen som finns på din product eller på dess förpackning påvisar att produkten inte ska behandlas som hushållsavfall när du vill slänga bort den. Istället ska den lämnas över till en lämplig uppsamlingspunkt för återvinning av elektriska och elektroniska utrustningar. Genom att tillförsäkra att den här produkten återvinns på ett riktigt sätt hjälper du till med att förhindra mö jliga negative konsekvenser för miljön och mänsklig hälsa. Det kan annars orsak as på grund av olämplig sophantering av den här produkten. Återvinning av mat erial kommer att hjälpa till att bevara naturtillgångar.

Den här symbolen är endast giltig inom den Europeiska unionen. Om du vill slänga bort den här produkten ska du ko ntakta lokala myndigheter eller återförsäljar, och frå ga efter lämplig avfallsmetod

Suomi

Vanhojen sähkö- ja elektroniikkalaitteiden hävittäminen (Sove ltuva kaikkialla Euroopan unionin alueella, sekä muissa Euroo pan maissa, joilla on erilliset keräysohjelmat)

Jos tuotteessa tai sen pakkauksessa on tämä symboli, sitä ei pidä hävitettäes sä käsitellä tavallisena kotitalousjätteenä, vaan se kuuluu toimittaa sähkö- ja el ektroniikkalaitteiden kierrätyspisteeseen. Varmistamalla, että tämä tuote hävitetään asiaankuuluvalla tavalla autat estämään mahdollisia y mpäristölle ja ihmisille koituvia negatiivisia seuraamuksia, joita sen vääränlain en hävittäminen voi aiheuttaa. Materiaalien kierrättäminen auttaa säilyttämää n luonnonvaroja.

Tämä symboli on voimassa ainoastaan Euroopan unionin alueella. Jos haluat hävittää tämän tuotteen, ota yhteyttä paikallis iin viranomaisiin tai jälleenmyyjään ja tiedustele asiaanku uluvia hävittämistoimenpiteitä.

- 2 - - 3 -

- 4 - - 5 -

Waste Electrical and Electronic Equipment (WEEE) Yönergeleri A vrupa Birliği'nde bu etiket, ürünün ev elektroniği aletleri atıkları ile imha edilemeyeceğini gösterir. Kurtarmak ve geri dönüşümünü sağlamak için uygun şartlarda sakl anması gerekir. EEE Yönetmeliğine Uygundur Ve Elektronik Eşyalar da Bazi Zararli Maddelerin Kullaniminin Sinirlandirilmasina Dair Yö netmelik.

Waste Electrical and Electronic Equipment (WEEE) Yönerg eleri Avrupa Birliği'nde bu etiket, ürünün ev elektroniği aletl eri atıkları ile imha edilemeyeceğini gösterir. Kurtarmak ve geri dönüşümünü sağlamak için uygun şartlarda saklanmas ı gerekir. EEE Yönetmeliğine Uygundur Ve Elektronik Eşyal arda Bazi Zararli Maddelerin Kullaniminin Sinirlandirilmasin a Dair Yönetmelik.

Consideration for easier service

- When you design the exterior design for monitor system, consider easier disassembly for possible service occasion in the future.

- The sliding Universal Unit of ORION is recommended for easier service.

- If service people can step into the backside ofmonitor system, it can greatly reduce time and effort for service.

- In case of higher locations, consider the installation location and exterior design for easier service.

Page 5

www.oriondisplay.net

Innitely Expandable

MLCD

※

Clearance for Ventilation

- When you install monitor make sure there is at least 20cm clearance for effective

WARNING

ventilation and do not seal off monitor sets. If monitor sets are installed at the locations of bad ventilation, the inner temperature can be raised rapidly and it can cause frequent malfunctions and rapid reduction of the product life.

※

Cleaning and Maintenance

- Regularly clean off the vent holes in the back of monitor sets. If the vent holes and the fan air holes are clogged with dust, it prevents the air

flow inside of monitor sets.

It can cause rapid increase of the inner temperature and may cause malfunctions. Clean off the vent holes and the fan air holes with a vacuum cleaner regularly.

WARNING

Vacuum Cleaner

* Ventilation space in front of monitor must be furnished for heat dispersion.If the

front space of monitor has to be sealed, there must be consideration for the heat dispersion in the rear side of monitor.

-6- - 7 -

Page 6

• If you need to stand LCD,

• If you need to lay down

• If you need to lay down LCD

• Please do not stand LCD

• Please do not lean over

• Please do not lean over the

you must lean over the

LCD as face down

as face up position, please be

alone. It may fall or slip off

the LCD. It may damage

LCD toward the edge part. It

LCD to avoid panel touches

position, please use

cautious for falling objects

and Panel can be broken or

the bottom part of the

may damage the edge part

ground or floor .

shock-absorbing pads

on the surface of the LCD.

damaged.

LCD.

of the LCD.

under the LCD.

www.oriondisplay.net

Innitely Expandable

MLCD

WARNING

※

Please keep following instructi on for panel protection without exception.

Warning Warning

※

Handle with Caution.

-Shock/Impact on the set's sides will result in internal circuit damages.

-The edge/bottom of the panel are fragile.

- This product can be damaged even with minor impact for its nature.

Use shock-absorbing pads or rugs for laying down the product.

WARNING

Please keep following instruction to carry or store the products.

PANEL

CUSHION

PANEL

- 8 - - 9 -

PANEL

Page 7

DEPARTURE

Flight No.

Time

Gate

UA 012

11:20

A02

KE 732

12:10

K17

AN 291

12:45

F11

DEPARTURE

Flight No.

Time

Gate

UA 012

11:20

A02

KE 732

12:10

K17

AN 291

12:45

F11

DEPARTURE

Flight N o.

Time

Gate

UA 012

11:20

A02

DEPARTURE

Flight N o.

Time

Gate

UA 012

11:20

A02

DEPARTURE

Flight N o.

Time

Gate

UA 012

11:20

A02

DEPARTURE

Flight N o.

Time

Gate

UA 012

11:20

A02

ARRIVAL

Flight No.

Time

Gate

Delay

AA 213

9:20

K11

On time

OZ 621

11:25

G21

10 min.

JA 032

12:05

A19

On time

ARRIVAL

Flight No.

Time

Embark

Delay

AA 213

9:20

New York

On time

OZ 621

11:25

Seoul

10 min.

JA 032

12:05

Beijing

On time

DEPARTURE

Flight No.

Time

Gate

UA 012

11:20

A02

KE 732

12:10

K17

AN 291

12:45

F11

DEPARTURE

Flight No.

Time

Gate

UA 012

11:20

A02

13:40

K17

UA 012

17:03

A02

DEPARTURE

Flight No.

Time

Gate

UA 012

11:20

A02

KE 732

12:10

K17

AN 291

12:45

F11

www.oriondisplay.net

Innitely Expandable

MLCD

※

How to carry

It always needs two persons to carry or install

WARNING

monitor . When you carry monitor with up straight

※

Application information

If static images are displayed on the screen for a long time, it causes burn-in image. Please keep the following instruction to optimize the lifetime and functions of the product.

manner, please hold handles on the back and bottom part of the panel together.

Please be careful not to touch the bottom part of the panel when you put down the panel.

Please do not touch the panel with your hand.

1. Operating condition

- Temperature: 20 ± 15˚C

- Humidity: 55 ± 20 %

- Display pattern: moving picture or regular switchover display

- Environmental condition : Well ventilated place is recommended.

- Power off and screen saver : Periodical power-off or screen saver is needed after long-term static display.

※ Note : Moving picture or black pattern is strongly recommended for screen saver.

WARNING

2. Operating methods to minimize burn-in image due to long-term static information

display

Don't carry monitor in Horizontal Status.

- For optimal performance, we suggest turning off the LED power on the monitor for four hours per day

- Periodical display contents change from static image to moving picture.

- Periodical background color and character (image) color change

When two operators uphold monitor, Panel is twisted by unbalanced handling.

ÅÆ

- Change the images of little luminance difference between the background and characters, periodically.

Æ Æ Æ

- It is not recommended to display the images of huge luminance difference between the background and characters or the images of grey tone.

(X) (X)

- Scroll the characters periodically.

Æ Æ

UA 012

(Whole Screen Scroll)

- 10 - - 11 -

Page 8

www.oriondisplay.net

Innitely Expandable

MLCD

WARNING

※

Attention for Installing

Warning

WARNING

• Avoid giving a shock or damage at LCD corner or other parts during setting Multi-Vision.

Fixed

• Avoid that LCD is twisted. • Keep all LCDs balanced in vertical or

horizontal force after setting

• Multi-Vision. Avoid LCD is set up tilted so it can give a damage to down LCD.

- 12 - - 13 -

• Avoid that LCD outside is shocked or damaged by sharp thing.

Page 9

www.oriondisplay.net

01. Safety Precautions

Innitely Expandable

MLCD

• If it operates abnormally, stop using it immediately.

• Please refer to a specialized construction company for installing stand or wall mount unit. Otherwise, damage or injury may be caused.

• Do not place any liquid-containing container on it. If the inside is wet, it may cause electric shock or fire.

• Do not touch the device when lightning strikes.

• Do not put any foreign material into the product. It may cause a failure or shorten the life span.

• Do not install in an unstable location It may cause injury.

• Do not pull out or hang down the connection cable. It may damage the cord to cause fire or electric shock.

• Pull out the power plug by holding the plug. Otherwise, it may damage the power cord to cause fire or electric shock.

• Do not lean against the product or keep it leaned. It may cause injury or failure.

• If you do not want to use the product for a long time, keep the power plug unplugged to save electricity.

• The socket-outlet should be installed near the equipment and be easily accessible.

• Do not put it at any place with much humidity, dust, oil, smoke or steam. It may cause failure.

• Do not put any heavy object on it. It may cause failure.

• Avoid any action to damage the power cord or power plug. It may cause fire or electric shock.

• Do not alter (or disassemble) the product. It may cause electric shock since high voltage is flowing inside.

• Do not pull out the power plug with a wet hand. It may cause electric shock.

• Do not install the product where it may be exposed to direct sunlight or near any heating device. It may shorten the product's life span or cause failure.

• Do not exceed ratings of AC outlet or extension cords. It may cause failure.

• Make sure the product is not covered with any object. If the ventilation hole is blocked, the inside temperature may rise to cause overheating resulting in fire.

• Install the product on safe and flat surface.

• Do not put candles on the product. If the liquid flows inside the product. It may cause electric shock or fire.

• Do not ride or step on the product It may cause breakage when fallen down.

• Do not touch product’s front surface with hand. Otherwise, the image quality can be lowered.

• When moving it, disconnect the connecting cable. Otherwise, it may damage the cable to cause fire or electric shock.

• Do not poke the front screen with sharp material. It may damage the screen and may cause malfunction of the product.

- 14 - - 15 -

Page 10

www.oriondisplay.net

02. Names

Innitely Expandable

MLCD

▶

Front

Rear

▶

Input Ports

❿

❾

1. AC IN

AC 100V ~ 240V, 50/60Hz

6. RS232C OUT

Display control via COM port

❼

❺

❸❽❹

❷

❻

❶

2. A/S

Only for Firmware upgrade.

3. LAN

Display control via Ethernet (RJ45)

4. IR

Remote controller input port

5. RS232C IN

Display control via COM port

(D-Sub 9pin, FEMALE)

(D-Sub 9pin, MALE)

7. DVI IN

To input Display Port signals

8. HDMI IN

To input HDMI video signal.

9. DP IN

To input DisplayPort video signal.

10. DP OUT

For loop through video with other

monitors for sharing video signal through

DisplayPort.

- 16 - - 17 -

Page 11

www.oriondisplay.net

03. How to Connect Cables

• Do not connect/disconnect cables while monitor or other external equipments are turned on.

• First turn off the power all the attached equipment and make connections.

• Make sure the power cord is inserted properly into the power inlet to prevent unexpected pullout of

the cord.

3.1. Connection of Single

ㆍMonitor and PC should be connected; a Com Port in a PC and RS-232C IN port in a monitor is

connected with supplied RS-232C cable.

ㆍ If you do not have Com Port, you need to use an USB converter for RS-232C. Depending on

manufacturers or models, converters may cause malfunction.

Innitely Expandable

MLCD

DVD player

DP Cable

HDMI Cable

DVI connection

RS-232C

LAN Cable(Cross Cable or Direct Cable)

Control PC

LAN Cable (Direct cable)

- 18 - - 19 -

LAN Cable (Direct cable)

HUB or Router

Page 12

INPUT SOURCE

Resolution

Output Port

Connection

Remark

3840 x 2160 x 60Hz

DP OUT

6 sets

HDCP Available

www.oriondisplay.net

Innitely Expandable

MLCD

3.2. Connection of Multiple (for DP in)

• Image quality can be affected by cable or signal quality.

• Please use DisplayPort cable with DisplayPort certified logo.

• Select DisplayPort cables feature a locking function. When removing this cable, hold down the top

button to release the lock.

• Recommended maximum set connection for Multi setting is shown in table below. If you need to connect more than described in the table, you have to use distributors.

DP IN DP OUT HDMI - IIN DVI IN DP IN DP IN HDMI - IIN DVI IN DP IN DP OUT HDMI - IIN DVI IN

3.3. Connection of Multiple (for HDMI in)

• It is recommended you purchase an HDMI-certified cable. Otherwise, the screen may appear blank or a connection error may occur.

• Image quality can be affected by cable or signal quality.

DP IN DP OUT HDMI - IIN DVI IN DP IN DP IN HDMI - IIN DVI IN DP IN DP OUT HDMI - IIN DVI IN

DP IN DP OUT HDMI - IIN DVI IN DP IN DP OUT HDMI - IIN DVI IN DP IN DP OUT HDMI - IIN DVI IN

※

Caution for DP Signal Distributor

If you want to display HDCP (High-bandwidth Digita

l Content Protection) applied contents, you must us

e the distributor that supports HDCP function.

Video Source

DP IN DP OUT HDMI - IIN DVI IN DP IN DP OUT HDMI - IIN DVI IN DP IN DP OUT HDMI - IIN DVI IN

HDMI Signal Distributor

HDMI Cable

DP Cable

Video Source

- 20 - - 21 -

Page 13

www.oriondisplay.net

Innitely Expandable

MLCD

3.4. Connection of Multiple (for DVI in)

• Image quality can be affected by cable or signal quality.

DP IN DP OUT HDMI - IIN DVI IN DP IN DP IN HDMI - IIN DVI IN DP OUT HDMI - IIN DP IN DVI IN

DP IN DP OUT HDMI - IIN DVI IN DP IN DP OUT HDMI - IIN DVI IN DP IN DP OUT HDMI - IIN DVI IN

3.5. Connection of Control Cable

• Control signal transmission can be connected by 3 different methods. (RS-232C or Ethernet or IR)

• RS-232C and Ethernet connection cannot be used simultaneously.

• All control signals are output to the RS-232OUT after conversion to RS-232C signal.

3.5.1. Connection of RS-232C Cable

• Maximum use of RS-232C with Daisy Chain connection is 30 sets or less, if you need

additional connection, use RS-232C distributor.

LAN IR RS232C IN RS232C OUT LAN IR RS232C IN RS232C OUT LAN IR RS232C IN RS232C OUT

DP IN DP OUT HDMI - IIN DVI IN DP IN DP OUT HDMI - IIN DVI IN DP IN DP OUT HDMI - IIN DVI IN

DVI Signal Distributor

DVI Cable

LAN IR RS232C IN RS232C OUT LAN IR RS232C IN RS232C OUT LAN IR RS232C IN RS232C OUT

RS-232C Cable

Video Source

- 22 - - 23 -

RS-232C control PC

Page 14

www.oriondisplay.net

Innitely Expandable

MLCD

3.5.2. Connection of Ethernet Cable

• In case of Ethernet connection, the control PC should be connected to one of monitor sets with Ethernet cable.For the connection between the monitor sets, they should be connected with RS-232C cables.

LAN IR RS232C IN RS232C OUT LAN IR RS232C IN RS232C OUT LAN IR RS232C IN RS232C OUT

4. ID Setting

• Refer to the next chapter for OSW use.

• Before ID Setting Using OSW, Make sure that all of the connected MLCD sets are turned on

by clicking “POWER ON” button in Broadcast.

4.1. Sequential Connection

ㆍIt is the sequential RS-232C cable connection according to the order of ID numbers.

ID 1 ID 2 ID 3

LAN IR

RS232C IN

ID 4 ID 5 ID 6

RS232C

OUT

LAN IR RS232C

RS232C

OUT

LAN IR RS232C

RS232C OUT

LAN Cable

(Direct Cable)

LAN IR RS232C IN RS232C OUT LAN IR RS232C IN RS232C OUT LAN IR RS232C IN RS232C OUT

LAN Cable(Cross Cable or Direct Cable)

HUB or Router

(Wireless & Cable)

LAN Cable

Ethernet control PC

(Direct Cable)

LAN IR

RS232C IN

RS232C

OUT

LAN IR RS232C

RS232C

OUT

LAN IR RS232C

ID 7 ID 8 ID 9

LAN I

RS232C IN

RS-232C

RS232C

OUT

LAN IR RS232C

RS-232C control PC

RS232C

OUT

LAN IR RS232C

RS232C OUT

- 24 - - 25 -

Page 15

www.oriondisplay.net

1. Click “MULTI → ID”

Innitely Expandable

MLCD

2. Click "AUTO ID SET" button in "ID" tab to complete ID setting.

3. After that, ID setting status in OSW Screen Configuration is as follows. It's same as physical RS-232C cable connection. Because "AUTO ID SET" sets the order of ID numbers according to the sequential RS-232C cable connection.

4.2. Random Connection

ㆍIt is the random RS-232C cable connection

ID 3 ID 4

LAN IR RS232C IN RS232C

ID 2

LAN IR RS232C IN RS232C

ID 1

LAN IR RS232C IN RS232C

OUT

LAN IR RS232C

ID 5

LAN IR RS232C

ID 6

LAN IR RS232C

regardless of the order of ID numbers.

ID 9

RS232C OUT LAN IR RS232C IN RS232C

ID 8

RS232C OUT LAN IR RS232C IN RS232C

ID 7

RS232C OUT LA

N IR RS232C IN RS232C

OUT

ID 1

ID 4

ID 7

ID 2

ID 5

ID 8

ID 3

ID 6

ID 9

- 26 - - 27 -

RS-232C

RS-232C c

ontrol PC

Page 16

www.oriondisplay.net

Innitely Expandable

MLCD

1. Click “MULTI → ID”.

2. Select another number, which is not in use, for “AUTO GROUP ID" and click "AUTO ID SET" in

“ID” menu

4. Identify the IDs of all connected MLCD sets by clicking "INFO" button in Broadcast.

5. First, Identify the IDs of upper left corner MLCD set.

6. Set the IDs identified through the above 4,5) procedure for “CURRENT GROUP/MONITOR ID” in “NEW ID” Menu. And then, set “NEW GROUP ID" as 1 and “NEW MONITOR ID" as 1 in “NEW ID" Menu. And click "NEW ID SET" button in “NEW ID” menu.

3. After that, ID setting status in OSW Screen Configuration is as follows. It's same as physical RS-232C cable connection. Because "AUTO ID" sets the order of ID numbers according to the sequential RS-232C cable connection.

* Group ID = GID, Monitor ID = MID

GID 2

MID 3

GID 2

MID 2

GID 2

MID 1

GID 2

MID 4

GID 2

MID 5

GID 2

MID 6

GID 2 MID 9

GID 2 MID 8

GID 2 MID 7

ID 3

ID 2

ID 1

Group ID 2, Multi ID 3 Group ID 1, Multi ID 1

ID 4

ID 5

ID 6

ID 9

ID 8

ID 7

ID 1

ID 4

ID 7

ID 2

ID 5

ID 8

ID 3

ID 6

ID 9

- 28 - - 29 -

Page 17

www.oriondisplay.net

Innitely Expandable

MLCD

7. Identify the IDs on the right MLCD set of upper left corner MLCD set in the same way as the above 4) procedure.

8. Set the IDs identified through the above 7) procedure for “CURRENT GROUP/MULTI ID” in “NEW ID” Menu. And then, Increase the number by 1 for “NEW MONITOR ID" in “NEW ID” Menu to set the ID order. and click "NEW ID SET" button in “NEW ID” menu.

9. Repeat the above 7) and 8) procedures for the rest of displays in the same order as the number of the 10) procedure's capture view.

10.After setting last MLCD set, ID setting status in OSW Screen Configuration is as follows. It's different from physical RS-232C cable connection.

ID 1

ID 4

ID 7

ID 2

ID 5

ID 8

ID 3

ID 6

ID 9

ID 1

ID 2

ID 1

Group ID 2, Multi ID 4 Group ID 1, Multi ID 2

ID 4

ID 5

ID 6

ID 9

ID 8

ID 7

ID 1

ID 4

ID 7

ID 2

ID 5

ID 8

ID 3

ID 6

ID 9

- 30 - - 31 -

Page 18

www.oriondisplay.net

5. OSD Menu

Innitely Expandable

MLCD

5.1. Picture Menu

• Use this menu to activate Brightness/Contrast/sharpness and the luminance of the

backlight adjustment.

MUL

Picture Multi-Display Input

Backlight Brightness Contrast Sharpness

Schedule

5.2. Input Menu

• Use the Input Source menu to select between different video inputs that are be connected to

the monitor.

MUL

Picture Input

HDMI DVI Auto Select

Schedule

Multi-Display

AUTO

[Picture Menu Table]

MENU SUB MENU DESCRIPTION RANGE

0 ~ 100

0 ~ 4

1.8/ 2.0/ 2.2/ 2.4

10000/ 9300/ 6500/

USER-RGB(0~255)

On / Off

0 ~ 100

Picture

Backlight

Brightness

Contrast

Sharpness

Gamma

Temperature

Studio Mode

Hue

Backlight adjusts the luminance of the backlight.

Brightness adjusts the brightness of the monitor.

Contrast adjusts the difference between darkness

and lightness on the monitor. Adjust the

brightness first, and then adjust the contrast only

if further adjustment is necessary.

Sharpness adjusts the sharpness of the monitor.

Select a display gamma for best picture quality.

Adjust the color temperature of the screen. If

color temperature needs further adjustment, the

individual RGB levels of the white point can be

adjusted. Can be used only in user mode of color

temperature

Select studio mode. The color temperature of

studio mode is about 3200k

Adjust the hue value of the screen

[Input Menu Table]

MENU SUB MENU DESCRIPTION RANGE

Select DP input when you are using the

DP(DisplayPort) connector.

Select the HDMI(MHL)input when you are

HDMI

using the HDMI connector. User to select the

HDMI(MHL)input source.

Input

DVI

AUTO INPUT

Select DVI input when you are using the DVI

connector.

Auto Detect input signal

Saturation

Adjust the saturation value of the screen

- 32 - - 33 -

0 ~ 100

Page 19

Menu Sub menu Description Range

Schedule On/Off Activate or deactivate the Schedule function. ON/OFF

Currentt Time Adjust the current date and time for the internal clock. -

Time Set

Set a schedule, Everyday/Sun/Mon/Tue/Wed/Thu/Fri/Sat. Set the tim e3 for the display to turn on and turn off.

Input Select

Select default input source to use when the display is automatically turned on next time.

DP/HDMI/

DVI/AUTO

Reset

Schedule Settings will be restored to factory-preset data or Return to Menu

ON/OFF

Schedule

www.oriondisplay.net

Innitely Expandable

MLCD

5.3. Schedule Menu

• Use this function to reserve the time when the monitor turned On or Off.

MUL

Picture Schedule

OFF ON

Schedule On/Off Current Time Time Set Input Select

23:04

Multi-Display Input

5.4. Multi-Display Menu

• Control multi-scaling functions in this menu.

Picture Input

ID2

ID1

ID3

/OFF

Multi On/Off Monitor ID

ID4

1 1 2 2 3

H-Monitor

Schedule

MUL

Multi-Display

1 2 1 2 1

V-Monitor

[Schedule Menu Table]

※ This Function is not supported yet.

- 34 - - 35 -

[Multi-Display Menu Table]

MENU SUB MENU DESCRIPTION RANGE

Multi On/Off

Monitor ID Assign the id to the monitor individually. 1~254

H-Monitor

Multi

Display

V-Monitor

Multi Position

B-Comp. Set Activate Bezel compensation.

B-Comp. Value Set bezel compensation numerically. 1~30

Activate the multi-scaling screen or Deactivate.

Set the number of horizontal monitor in multi-screen.

Set the number of vertical monitor in multi-screen.

Set the position number of the segment image in multi screen.

On / Off

1~16

1~254

On / Off

Page 20

www.oriondisplay.net

Innitely Expandable

MLCD

5.5. Other Menu

• Reset of the OSD settings, menu time, transparency, position and rotation of the OSD can be adjusted in other menu.

Other Information

Reset

Reset Menu Time OSD H Position OSD V Position

OSD

5.6. Information Menu

• The informaton of input source is shown.

Other Information

3840x2160@60Hz

H: 135.0KHz PCLK: 594.0MHz

HDCP Disabled

GROUP ID 1

MONITOR ID 1

[Other Menu Table]

OTHER

SUB MENU DESCRIPTION

MENU TIME

OSD H POSITION

OSD V POSITION

LANGUAGE

TRANSPARENCY OSD transparency ratio adjustment

OSD ROTATE OSD rotation

FAN On/Off Turn On/Off the fan operation

Model Info

Auto Power

RESET

LAN

Initialize all the setting value and options.

OSD operation time

OSD horizontal position adjustment

OSD vertical position adjustment

Select the language

View model name, IP address, Subnet Mask, Gateway

Turn on or off the Lan operation

Turn on or off the Auto Power

RANGE

3 ~ 60

0 ~ 100

EN/DE/FR/ES/NL/PL/

RU/IT

0 ~ 10

0º / 90º/ 270º

On / Off

 Check it out via the info button.

3840x2160@60Hz

HDCP Disabled

GROUP ID 1

MONITOR ID 1

- 36 - - 37 -

Page 21

www.oriondisplay.net

6. Setting and Operation of OSW

Innitely Expandable

MLCD

6.1. Installation

• Insert the Installation CD.

• You can see following installation start screen.

• Select proper version for your product and start installation

• OSW supports Window® (2000, XP, Vista, 7, 8, 10).

6.2. Start OSW

• OSW is a software for controlling Orion’s monitor.

• When you execute OSW (v1.0.6) for your product at the installation screen, it will create a new

folder at C:\Program Files \ORION and an icon on your computer screen.

• By double clicking the ORION OSW (v1.0.6) icon, the initial screen image of OSW (v1.0.6) will be displayed as shown in the picture.

* OSW Versions can be changed for function improvement without prior notice.

Caution for using OSW

Caution

1. Specific features can be read by clicking the left button of your mouse on the desired MLCD set from OSW. Please do not use above function together with the other functions.

- 38 - - 39 -

Main Image of OSW (Orion Software)

Page 22

www.oriondisplay.net

Innitely Expandable

MLCD

6.2.1 Main Menu

①

②

③

④

⑤

⑥

① POWER

Power On/Off.

② INPUT SOURCE

Input Source.(DP, HDMI, DVI, AUTO)

③ MONITOR CONFIGURATION

Monitor Configuration X*Y(16*16) Set.

④ MODE

Broadcast Mode, Drag Mode.

⑤ MULTI SCALE

Full Screen On/Off.

⑥ POSITION

Screen Position.

⑦ OSD INFO

6.2.2 Multi Panel

• This is a panel for selecting monitor.

• It can help for controlling

1x1

2x2

⑦

⑧

⑨

On Screen Display Information.

⑧ APPLICATION

Picture, Help, Multi

⑨ OTHER

Display, Fan, Lan, Lock, Power, Bezel Comp.

5x1 3x3

- 40 - - 41 -

Page 23

www.oriondisplay.net

6.3. Communication Configuration

Innitely Expandable

MLCD

6.3.1. COM Port For OSW

• Com Port connects or disconnects the communication between PC and MLCD.

• Connect MLCD to PC Com Port via RS-232C cable.

• Go to “OSW Menu → CONNECTION → CONNECT" and select the comport you want to

connect.

• In order to disconnect the communication, click "DISCONNECT"..

• When you use USB-to-RS-232C converters, you need to set Com Port again,

because OSW uses one of Com Port no. 1 to 30.

※Available Com Port on the PC is automatically recognized and displayed.

6.3.3. Socket Setup

1. Execute the OSW.

2. Select “OSW Menu → CONNECTION → SOCKET SETUP".

3.Type in IP Address of MLCD.

4.Click "PING TEST" to check status of communication.

5.Close the Communication setup window

6.3.2. LAN Port For OSW

• LAN Port connects or disconnects the communication between PC and MLCD.

• Connect MLCD to PC LAN Port via LAN cable.

• Go to “OSW Menu → CONNECTION → CONNECT" and select the LAN port you want to

connect.

• In order to disconnect the communication, click "DISCONNECT"..

※Destination IP address is configured using “SOCKET SETUP" menu.

※Destination IP address is IP address of the MLCD you want to connect.

•Socket Setup Menu Description

•Edit Box

•Port Number

* Caution: You cannot change the port number.

•Ping Test

: Set the IP address.

: Fixed as 9761.

: Test the IP address.

SOCKET SETUP

-42 - - 43 -

Page 24

www.oriondisplay.net

6.3.4. LAN Port For MLCD

6.3.4.1 In case of connection to a LAN Hub

• This function is used to control the MLCD via LAN PORT.

• During the setting process, MLCD and control PC should be connected via RS-232C

cable only. Do not connect Ethernet.

• After setting process, the control PC should be connected to one of MLCD sets with

Ethernet cable only. For the connection between the MLCD sets, they should be connected with RS-232C cables.

※The Ethernet cable should be connected to RS-232C starting point

■ Network IP setting for MLCD

1. Execute the OSW.

2. After Serial Connection, Turn on the MLCD.

3. Click left button of the mouse on the MLCD that you want to control on the screen con figuration window.(This MLCD should be connected to LAN cable)

4. Click “ OTHER → LAN “

Innitely Expandable

MLCD

5. Type in the IP address provided by the network administrator.

- 44 - - 45 -

Page 25

www.oriondisplay.net

6. Save the IP address by clicking “SET TCP/IP” after type-in.

Innitely Expandable

MLCD

6.3.4.2. In case of connection to user's computer

■ Check the network informations

1. Execute the OSW.

2. After Serial Connection, Turn on the MLCD.

3. Click left top of the mouse on the MLCD that you want to control on the screen configuration window.(This MLCD should be connected to LAN cable)

4. Click → OTHER → LAN

5. Click the "LAN ON" and click "GET TCP/IP" to read the initial network

configuration of the MLCD.

7. Click "GET TCP/IP" and check whether the IP address is correct.

- 46 - - 47 -

Page 26

www.oriondisplay.net

6.4. Screen Configuration

Innitely Expandable

MLCD

6. Input the network information of the user’s PC to be identical with MLCD set. However, the final digit of the IP address must be different.

■ Input column/row number of the MLCD Matrix.

• Column/row can be selected within the range from 1 to 16. The maximum MLCD

quantity

• of OSW control is 254 sets. After inputting column/row number, MLCD matrix with input source color is displayed in the "Screen Configuration" after click the button “SET”

Screen Configuration Setting

■ BROADCAST.

• When broadcast checkbox is checked, entire command transmission method is

broadcast.

• When broadcast checkbox is not checked, entire command transmission method is

normal mode.

• User Transmit the Protocol command respectively to Selected MLCD Sets in normal

transmission method.

※You can't select the MLCD in screen configuration in broadcast.

Mode Setting

■ DRAG MODE.

• When the Drag Mode checkbox is not checked, the screen configuration window will be

clicked only one.

- 48 - - 49 -

Page 27

www.oriondisplay.net

Innitely Expandable

MLCD

6.5. Explanation of the command transmission method.

■ Normal Transmission Method.

: You select MLCD sets in "Screen Configuration Window" clicking the left button of the mouse.

Maybe you want to select more than one MLCD set, drag the mouse. Then you can transmit

the Protocol command respectively to selected MLCD Sets.

■ Broadcast Transmission Method.

: When broadcast checkbox is checked, entire command transmission method is broadcast.

You can transmit the Protocol command simultaneously to all connected MLCD sets.

※All Protocol commands are affected by the command transmission method.

6.6. Basic Control

• To control basic operation in Main Screen.

• POWER : “ POWER ON/OFF " button is to control power of selected MLCD Sets.

Caution

• Please wait for at least 10 seconds before executing "Power On" command after the first AC power connection. If not, it may cause abnormal behavior.

• Please disconnect AC power and reconnect in case of abnormal behavior.

• MULTISCALE : “ Full Screen On " button is to make multiscaling screen. “ Full Screen Off "

button is to make individual screen.

• Drag the panel -> Click the “Full Screen On” button

< Full Screen On > < Full Screen Off >

- 50 - - 51 -

Page 28

www.oriondisplay.net

Innitely Expandable

MLCD

•

INPUT

SOURCE : To select one of input sources from DP, HDMI, DVI, AUTO Port.

POSITION

•

1. Select → Screen configuration window

2. Click the “Change” button after change the position number

: To change monitor position.(only one monitor)

INFO. : “INFO." button is to display the resolution of the input source and the signal. It is

•

displayed at the center of the screen.

3840x2160@60Hz

HDCP Disabled

Group ID 1

Monitor ID 1

ID 1 ID 2

ID 3

ID 4

ID 1 ID 2

ID 3

ID 4

- 52 - - 53 -

Page 29

www.oriondisplay.net

Innitely Expandable

MLCD

3. Select → Screen configuration window

4. Click the “Change” button after change the position number

ID 1 ID 2

6.7. Control

6.7.1. Power ON Control

• Go to “OTHER → POWER" to control power related operation.

ID 3 ID 4

ID 3

- 54 - - 55 -

ID 4

AUTO POWER : Automatic power on by AC power connection.

•

Page 30

www.oriondisplay.net

Innitely Expandable

MLCD

6.7.2. Display Control

• Go to “OTHER → DISPLAY" to control display related operation.

6.7.3. Picture Control

• To use Picture Control, go to “ APPLICATION → PICTURE ".

• DISPLAY RESET : Reset of setting value to default.

- 56 - - 57 -

Page 31

www.oriondisplay.net

Innitely Expandable

MLCD

• BRIGHTNESS : Brightness adjusts the brightness

of the monitor

. (0~100)

• CONTRAST : Contrast adjusts the difference between darkness and lightness on the monitor.

(0~100)

• SHARPNESS : Sharpness adjusts sharpness of the monitor. (0~4)

• HUE : Adjust the hue value of the screen. (0~100)

• SATURATION : Adjust the saturation value of the screen. (0~100)

• BACKLIGHT : Adjust the backlight value of the screen.(0~100)

• GAMMA : Select a display gamma for best picture quality.(1.8/ 2.0/ 2.2/ 2.4)

• COLOR TEMP : Color temperature of the screen - 10000K, 9300K, 6500K, STUDIO, USER.

6.7.4. FAN Control

• Go to “ OTHER → FAN " to control fan related operation.

- 58 -

FAN : FAN On/Off

•

- 59 -

Page 32

www.oriondisplay.net

Innitely Expandable

MLCD

6.7.5. LOCK Control

• Go to “ OTHER → LOCK " to control lock operation.

6.7.6 Help

• Go to “ APPLICATION → HELP “ to check model information

IR Lock : IR (Remote Controller) Lock On or Off

•

- 60 - - 61 -

Page 33

www.oriondisplay.net

Innitely Expandable

MLCD

• Model Info : Click → “ GET ” button to check model information

• About OSW : Click → “ About OSW ” tab to check osw information

• TAG NAME SET

1. Select the panel

2. Type in edit box and click the set button.

3. Check the Tag name

- 62 - - 63 -

Page 34

www.oriondisplay.net

6.7.7. Bezel Control

• Go to “ OTHER → Bezel Comp “ to control Bezel Compensation

Innitely Expandable

Bezel Compensation : Bezel Compensation On/Off

•

Bezel Comp Value : Compensating the frame width.(0~30)

•

MLCD

- 64 - - 65 -

Page 35

STX

START OF CODE

0x02

1 BYTE

MCMD

MAIN COMMAND

VARIABLE

1 BYTE

SCMD

SUB COMMAND

VARIABLE

1 BYTE

LEN

LENGTH OF ID & DATA

VARIABLE

1 BYTE

GID

GROUP ID

VARIABLE

1 BYTE

ID = 0 :

ALL MONITOR(BROADCAST)

MID1

MONITOR ID (MSB)

VARIABLE

1 BYTE

MID2

MONITOR ID (LSB)

VARIABLE

1 BYTE

FIRST DATA

VARIABLE

1 BYTE

DATA : n BYTE

nTH DATA

VARIABLE

1 BYTE

CHECKSUM

VARIABLE

1 BYTE

SUM = "FF“

EXT

END OF CODE

0x03

1 BYTE

www.oriondisplay.net

7. PROTOCOL

2. Protocol

Format

Innitely Expandable

MLCD

■ Introduction

- This document contains the communication PROTOCOL between LCD and its control devices for better use.

- It focuses on the brief functional explanation and communication protocol without detailed

technical matters.

7.1. Communication Setting

ITEM SPECIFICATION

TRANSMISSION & RECEPTION TYPE A

CONNECTION TYPE DAISY CHAIN

BAUD RATE 57600 bps

DATA BITS 8

SYNCHRONOUS SERIAL COMMUNICATION

2.1 Send Protocol Format

STX COMMAND LEN DATA EXT

STX MCMD SCMD LEN GID MID1 MID2 D1 … Dn EXT

2.2 Receive Protocol Format

STX COMMAND LEN DATA CS EXT

STX MCMD SCMD LEN GID MID1 MID2 D1 … Dn CS EXT

* STX - 0x02, EXT - 0x03

2.3 Description of Protocol Format

ITEM DESCRIPTION VALUE SIZE REMARK

PARITY NONE

STOP BITS

FLOW CONTROL NONE

CABLE & PIN ASSIGN

9PIN D-SUB, MALE / FEMALE STRAIT TYPE

C PIN NO. PIN

RX DATA 2 2 TX DATA

TX DATA 3 3 RX DATA

GND 5 5 GND

- 66 - - 67 -

NO. MONITOR

Page 36

INPUT SOURCE

GAMMA

COLOR TEMPERATURE

USER RED/GREEN/BLUE

HUE

www.oriondisplay.net

7.3. Command

3.1 Power Control Command and Data

FUNCTION MCMD SCMD DATA REMARK

POWER ON/OFF 0x0100 D1 : 0x01-ON, 0x00-OFF

AUTO POWER ON ON/OFF 0x0110 D1 : 0x01-ON, 0x00-OFF

DIALOG BOX OPEN (AUTO POWER)

3.2 Display Control Command and Data

FUNCTION MCMD SCMD DATA REMARK

DIALOG BOX OPEN 0x02F0 - READ ONLY DIALOG BOX OPEN (MONITOR DATA) D2 : POWER ON INPUT RESET (W/ DEFAULT DATA)

0x01F0 - READ ONLY

0x01F0 D1 : 0x01-ON, 0x00-OFF RECEIVE ONLY

0x0210

0x02F0

0x02FE

D1 : 0x30-DP, 0x20-HDMI, 0x10-DVI,

0x80-AUTO

D1 : 0x00 (FIXED, NOT USED)

D3 : ROTATE

RECEIVE ONLY

WRITE ONLY

Innitely Expandable

DIALOG BOX OPEN 0x03F0 - READ ONLY

DIALOG BOX OPEN

0x03F0

(W/ MONITOR DATA) D2 : CONTRAST

RESET

(W/ DEFAULT DATA) D4 : BACKLIGHT

0x03FE

D1 : BRIGHTNESS RECEIVE ONLY

D3 : SHARPNESS WRITE ONLY

D5 : GAMMA

D6 : COLOR TEMPERATURE

D7 : USER COLOR TEMPERATURE RED

D8 : USER COLOR TEMPERATURE GREEN

D9 : USER COLOR TEMPERATURE BLUE

D10 : HUE

D11 : SATURATION

MLCD

3.4 Multi Display Control Command and Data

3.3 Picture Control Command and Data

BRIGHTNESS 0x0300 D1 : 0 ~ 100 (DEFAULT 50)

CONTRAST 0x0301 D1 : 0 ~ 100 (DEFAULT 50)

SHARPNESS 0x0302 D1 : 0 ~ 4 (DEFAULT 2)

BACKLIGHT 0x0310 D1 : 0 ~ 100 (DEFAULT 90)

SATURATION 0x0324 D1 : 0 ~ 100 (DEFAULT 50)

FUNCTION MCMD SCMD DATA REMARK

D1 : 0x00-OFF, 0x01-1.8, 0x02-2.0

0x0320

0x03-2.2, 0x04-2.4

D1 : 0x00-USER, 0x03-STUDIO, 0x41-6500,

0x0321

0x5D-9300, 0x64-10000

D1 : 0x00-RED, 0x02-GREEN, 0x03-BLUE

0x0322

D2 : 0 ~ 255 (DEFAULT 127)

0x0323 D1 : 0 ~ 100 (DEFAULT 50)

- 68 - - 69 -

FUNCTION MCMD SCMD DATA REMARK

NEW ID SET

0x0600

AUTO ID 0x0601 - WRITE ONLY

MULTI SCALE

0x0610

BEZEL COMP. ON/OFF 0x0620 D1 : 0x01-ON, 0x00-OFF

BEZEL COMP. VALUE 0x0621 D1 : 0 ~ 30 (DEFAULT 0)

DIALOG BOX OPEN 0x06F0 - READ ONLY

DIALOG BOX OPEN

0x06F0

(W/ MONITOR DATA) D2 : BEZEL COMP. VALUE

RESET

0x06FE

(W/ DEFAULT DATA)

D1 : NEW GROUP ID NO. WRITE ONLY

D2 : NEW MONITOR ID NO. (MID1)

D3 : NEW MONITOR ID NO. (MID2)

D1 : TOTAL COLUMN NO.

D2 : TOTAL ROW NO.

D3 : GROUP ID NO.

D4 : MONITOR ID NO. (MSB)

D5 : MONITOR ID NO. (LSB)

D1 : BEZEL COMP. ON/OFF RECEIVE ONLY

D3 : POWER ON DELAY WRITE ONLY

Page 37

www.oriondisplay.net

Innitely Expandable

MLCD

3.5 OSD Control Command and Data

FUNCTION MCMD SCMD DATA REMARK

INFORMATION OSD ON 0x0710 - WRITE ONLY

3.6 E.T.C Control Command and Data

FUNCTION MCMD SCMD DATA REMARK

FAN ON/OFF 0x07A0 D1 : 0x01-ON, 0x00-OFF

IR LOCK 0x0800 D1 : 0x01-ON, 0x00-OFF

DIALOG BOX OPEN 0x08F1 - READ ONLY

DIALOG BOX OPEN

0x08F1

(W/ MONITOR DATA) D2-IR LOCK

D1-FAN ON/OFF, RECEIVE ONLY

3.7 LAN Configuration Command and Data

FUNCTION MCMD SCMD DATA REMARK

LAN ON/OFF 0x0750 D1 : 0x01-ON, 0x00-OFF

D1~D4 : IP ADDRESS READ ONLY

GET TCP/IP

0x0760

D5~D8 : SUBNET MASK

D9~D12 : GATEWAY

D13~D17 : DNS PORT NUMBER

3.8 Model Information Command and Data

FUNCTION MCMD SCMD DATA REMARK

SET TAG NAME 0x0031 D1~D16 : TAG NAME

DIALOG BOX OPEN 0xA0F0 - READ ONLY

DIALOG BOX OPEN

(W/ MONITOR DATA)

0xA0F0

D1~D16 : MODEL NUMBER

D17~D32 : TAG NAME

D1~D16 : FIRMWARE VERSION

0xA0F1

D17~D19 : MAC ADDRESS

RECEIVE ONLY

3.9 Monitor Status Command and Data

FUNCTION MCMD SCMD DATA REMARK

DIALOG BOX OPEN 0xA1F0 - READ ONLY

D1 : POWER STAUTS (0x01-ON, 0x00-OFF)

D2 : AUTO POWER ON (0x01-ON, 0x00-OFF)

D3 : GROUP ID (1 ~ 5)

DIALOG BOX OPEN

(W/ MONITOR DATA)

0xA1F0

D4 : MONITOR ID (MSB, 0x00 FIXED)

D5 : MONITOR ID (LSB, 0~254)

D6 : INPUT SOURCE (0x30-DP, 0x20-HDMI,

0x10-DVI, 0x80-AUTO)

D7 : RESOLUTION

RECEIVE ONLY

D1~D4 : IP ADDRESS

SET TCP/IP

RESET TCP/IP

DIALOG BOX OPEN 0x07F0 - READ ONLY

DIALOG BOX OPEN

(W/ MONITOR DATA)

0x0761

0x07FE

0x07F0

D5~D8 : SUBNET MASK

D9~D12 : GATEWAY

D1~D4 : IP ADDRESS (192.168.0.2)

D5~D8 : SUBNET MASK (255.255.255.0)

D9~D12 : GATEWAY (192.168.0.1)

D1-LAN ON/OFF RECEIVE ONLY

D2~D5 : IP ADDRESS

D6~D9 : SUBNET MASK

D10~D13 : GATEWAY

D14~D18 : DNS PORT NUMBER

- 70 - - 71 -

Page 38

Resolution

Pixel Clock [MHz]

Horizontal [Pixels]

Vertical [Lines]

Polarity

(H. / V.)

Standard

Type

Input

Total

Addr.

Width

Sync.

Width

Back

Porch

Total

Addr.

Width

Sync.

Width

Back

Porch

640*480*60

25.175

800

640

525

480

- / -

DMT

DVI/

HDMI/

800*600*60

40.002 1056

800

128

628

600

- / -

DMT

1024*768*60

1344

1024

136

160

806

768

- / -

DMT

1280*768*60

79.5

1664

1280

128

192

798

768

+ / +

CVT

1360*768*60

85.5

1792

1360

112

256

795

768

+ / +

CVT

1280*1024*60

108

1688

1280

112

248

1066

1024

- / -

DMT

1600*1200*60

162

2160

1600

192

304

1250

1200

+ / +

DMT

480P

858

720

525

480

- / -

CEA-861

HDMI/

576P

864

720

625

576

- / -

CEA-861

720P24

59.4

3300

1280

220

750

720

+ / +

CEA-861

720P25

74.25

3960

1280

220

750

720

+ / +

CEA-861

720P30

74.25

3300

1280

220

750

720

+ / +

CEA-861

720P50

74.25

1980

1280

220

750

720

+ / +

CEA-861

720P60

74.25

1650

1280

220

750

720

+ / +

CEA-861

1080P24

74.25

2750

1920

148

1125

1080

+ / +

CEA-861

DVI/

HDMI/

1080P25

74.25

2640

1920

148

1125

1080

+ / +

CEA-861

1080P30

74.25

2200

1920

148

1125

1080

+ / +

CEA-861

1080P50

148.5

2640

1920

148

1125

1080

+ / +

CEA-861

1080P60

148.5

2200

1920

148

1125

1080

+ / +

CEA-861

3840*2160*30

297

4400

3840

296

2250

2160

+ / +

HDMI/

3840*2160*60

594

4400

3840

296

2250

2160

+ / +

www.oriondisplay.net

Innitely Expandable

MLCD

8. Before calling for service

ㆍ Before calling for any repair, check the following and then refer to a near A/S center.

▶"Tick" sound from the main body.

- If there is no problem with the screen or sound, the "tick" sound is likely to result from the cabinet lightly shrinking with the change of room temperature. The sound does not affect product’s performance. ORION Homepage Log on

▶No image at upper and lower part of the screen.

- As for a screen which is over 16:9 in width (such as cine ma-sized one), no image may be displayed at upper and bottom part of the screen.

9. Applicable signals

※ Vertical Frequency : Standard ±0.5 Hz, Vertical Lines : Standards ±7 Lines * H [dot] / V [line]

▶Speckles or white lines on the screen

- Check whether the problem is caused by vehicle, streetcar, hi gh- voltage cable or neon sign, which emitting interference wa ve or electromagnetic induction. Avoid any interfering object.

▶Light leakage can be found at the edge areas around the screen.

- If the light leakage is not detected at 1m from the screen, the panel is considered as no defect.(LG LCD applies the same in spection standard)

- To minimize the light leakage, the monitor sets should be ins talled with high accuracy in horizontal and vertical position.

- 72 - - 73 -

Page 39

Product Name

UNB Multi-LCD Monitor

Model Name

OLMU-K4650

OLMU-K4670

OLMU-K5550

OLMU-K5570

LCD

Panel

Manufacture

SAMSUNG

Back Light Unit Type

Direct LED

Module Dimension(H x V mm)

1021.98 x 576.6

1213.4 x 684.2

Active Display Area(H x V mm)

1018.08 x 572.7

1209.6 x 680.4

Number of Pixels(H x V)

1920 x 1080 (16:9)

Pixel Pitch(mm)

0.530 x 0.530

0.630 x 0.630

Display Colors

16.7M(8bit)

1.06Billion(10bits)

Luminance of White(Typ. cd/m2)

500

700

500

700

Contrast Ratio(Typ.)

3,500 : 1

1,400 : 1

1,200 : 1

Surface Treatment

Haze 44%, Anti-Glare, 3H

Haze 10%, Anti-Glare, 3H

Life Time(Typ. Ta : 25±℃)

50,000Hrs

60,000Hrs

Power Supply

AC 100V ~ 240V±10% (50/60Hz)

Power Consumption(W)

Maximum

140

180

250

310

Typ.

120

160

220

270

Stand-By

≤ 0.5

Seam Gap_Multi

Configuration(Typ. mm)

3.7(Bezel to Bezel)

3.5(Bezel to Bezel)

Dimension (W x H x D mm)

1022 x 576.6 x 100.8

1213.4 x 684.2 x 100.5

Mounting (H x V mm)

580 x 340

600 x 400

Weights (kg)

23 ± 0.5

32 ± 0.5

Orientation

Portrait / Landscape

Input Signal

Support Resolution

480p, 576p, 720p, 1080p, UHD

HDCP

Ready

Frequency

H : 31~140kHz, V : 29~76Hz

In/Output Terminal

Input

DP x 1, HDMI x 1, DVI x 1, RS-232C x 1,

LAN x 1, IR x 1, A/S x 1

Output

DP x 1, RS-232C x 1

www.oriondisplay.net

Innitely Expandable

MLCD

10. Specification

11. Regulatory Information

Manufacturer's Name: ORION CO.,LTD.

Manufacturer's Address: 217, 1gongdan-ro, Gumi-si, Gyeongsangbuk-do, Korea D

eclares that the products Model Numbers: OLMU-K5550

Conforms with the provisions of:

Council Directive 2004/108/EC on Electromagnetic Compatibility; EN55022:2010 Radiated and C

onducted Emissions from IT Equipment EN55024:2010 Immunity of IT Equipment

Including: EN61000-4-2

EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-8 EN61000-4-11

And: EN61000-3-2

EN61000-3-3

Electrostatic Discharge Radiated Immunity Electrical Fast Transients Line Surge RF Conducted Susceptibility Magnetic Field Immunity Voltage Dips and Interrupts

Harmonic Current Emissions Voltage fluctuations and Flicker

Council Directive 2006/95/EC on Low Voltage Equipment Safety:

EN60950:2006+A11+A1+A12 Safety of IT Equipment

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Any changes or modifications to the display not expressly approved by could void the user's authority to operate this equipment.

Other Certifications

CISPR 22

- 74 - - 75 -

Page 40

www.oriondisplay.net

12. Dimension

Innitely Expandable

MLCD

12.1.OLMU-K4650 / OLMU-K4670

2.3

1,022±2

580

2.3

1.4

12.2. OLMU-K5550 / OLMU-K5570

2.5

1.4

100.8±2

1213.4

100.8±2

306.2 600 307.1

1.4

100.5

340

576.6±2

- 76- - 77 -

400 113.1 171.0

684.2

Page 41

www.oriondisplay.net

Innitely Expandable

MEMOMEMO

MLCD

- 78 - - 79-

Orion OLMU-K4650, OLMU-K5550, OLMU-K4670, OLMU-K5570 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual