Page 1
User Guide
UHF300 Micro 5watt UHF CB Radio
Downloaded from www.cbradio.nl
Keep this user guide for future reference. Always retain your
proof of purchase in case of warranty service and register your
product on line at: AUSTRALIA: www.oricom.com.au
Page 2
Why has the ACMA increased the number of available UHF CB channels?
To provide additional channel capacity within the UHF CB Band the ACMA will over the next 5 years change the
majority of the current wideband 40 channel use to narrowband 80 channel use.
During this time wideband channel use will be gradually phased out as users upgrade their existing radio’s.
This means that the new Oricom narrowband radio you have purchased will have more channels than older wideband
radios. Some of these channels are locked and cannot be used, (see the attached channel chart for more information).
When will this take place?
Early in 2011 new AS/NZS Standards came into effect allowing operators to use additional narrowband channels
and also use narrowband transmissions on some current wideband channels. This increased the number of
channels up to 80, 75 of which are useable voice channels.
What issues may users experience during the transition phase?
When a new narrowband radio receives a transmission from an older wideband radio the speech may sound loud
and distorted – simply adjust your radio volume for the best listening performance. When an older wideband radio
receives a signal from a new narrowband radio the speech may sound quieter - simply adjust your radio volume for
best listening performance. When operating a narrowband radio or Channel 41 - 80 interference is possible from
wideband radios transmitting on high power or on adjacent frequency.
The issues described above are not a fault of the radio but a consequence of mixed use of wideband and
narrowband radios.
It is expected that as older wideband radios are removed from service that this issue will be resolved. Most radios in
use will be narrowband eliminating this issue.
This information is current at time of printing. For further up to date information please visit www.acma.
gov.au
Oricom Connecting you now.
This unit complies with all relevant Australian
and New Zealand approval requirements
AS/NZS 4365:2011
Need Help?
If you need assistance setting up or using your Oricom product now or in the future, call Oricom Support.
Australia 1300 889 785
www.oricom.com.au
Mon-Fri 8am – 6pm AEST
New Zealand 0800 67 42 66
www.oricom.co.nz
Mon-Fri 10am – 8pm NZST
Page 3
Table of contents
Important information ....................................................................................................................4
Please read before installing or operating Your Oricom Radio .........................................................4
Safety information and Warnings....................................................................................................4
Box contents ...................................................................................................................................5
Features ..........................................................................................................................................5
Controls and Connectors ................................................................................................................6
Front view ......................................................................................................................................6
Rear view ......................................................................................................................................6
Microphone (Part No. MIC300) .......................................................................................................7
LCD icons & Indicators ...................................................................................................................7
Installtion ........................................................................................................................................8
Caution ..........................................................................................................................................8
Fitting the Microphone ...................................................................................................................8
DC Power connection .....................................................................................................................8
Over voltage protection ..................................................................................................................9
Antenna information & Installation ...............................................................................................10
Optional accessory ......................................................................................................................10
Operations .....................................................................................................................................11
Power On/Off ...............................................................................................................................11
Volume control .............................................................................................................................11
Selecting a channel .....................................................................................................................11
Setting the Squelch Level.............................................................................................................12
Menu ...........................................................................................................................................12
Menu list .....................................................................................................................................13
CTCSS and DCS setting ...............................................................................................................14
Duplex .........................................................................................................................................14
Open Scan (OS) Mode ..................................................................................................................16
Group Scan (GS) Mode .................................................................................................................16
Priority Channel ...........................................................................................................................17
Busy channel Lock .......................................................................................................................17
Roger Beep ..................................................................................................................................17
Key Beep .....................................................................................................................................17
Call tone ......................................................................................................................................17
LCD Backlight level ......................................................................................................................18
7 Colour backlight ........................................................................................................................18
Scan delay time ...........................................................................................................................18
Squelch delay time ......................................................................................................................18
Flip LCD .......................................................................................................................................18
Monitor ........................................................................................................................................19
Scan ............................................................................................................................................19
Memory On/Off ............................................................................................................................19
Transmitting.................................................................................................................................20
Factory Reset ...............................................................................................................................20
UHF channels and frequencies ....................................................................................................21
Frequency table of channel ..........................................................................................................21
CTCSS Freuqncies table ...............................................................................................................23
DCS code table ............................................................................................................................24
Customer Support .........................................................................................................................25
Warranty........................................................................................................................................26
3
Page 4
Important information
Please read before installing or operating Your
Oricom Radio
The operation of this radio in Australia and New Zealand is subject
to conditions in the following licenses. In Australia the ACMA Radio
communications (Citizen Band Radio Stations) and in New Zealand
by MED the General User Radio License for Citizen Band Radio and
operation is subject to conditions contained in those licenses.
Safety Information and Warnings
Potentially Explosive Atmosphere
WARNING
Turn your radio OFF when in any area with a potentially explosive
atmosphere. Sparks in such areas could cause an explosion or re
resulting in injury or even death.
NOTE: Areas with potentially explosive atmospheres are often, but
not always clearly marked. They include fueling areas such as below
deck on boats; fuel or chemical transfer or storage facilities; areas
where the air contains chemicals or particles, such as grain, dust,
or metal powders; and any other area where you would normally be
advised to turn off your vehicle engine.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn your radio
OFF near electrical blasting caps or in a “blasting area” or in areas
posted: “Turn off two way radios.” Obey all signs and instructions.
Electromagnetic Interference/Compatibility
Nearly every electronic device is susceptible to electromagnetic
interference (EMI). To avoid the possibility of electromagnetic
interference and/or compatibility conicts, turn off your radio in any
location where posted notices instruct you to do so such as health
care facilities.
4
Page 5
Important information
Box contents
Main Radio unit
Standard microphone
Owner’s Manual
Microphone hanger with screws, washers.
Mounting bracket with mounting screws
DC power cord with fuse
Features
• Transmit FM 75 & Receive FM 77 Channels to meet latest ACMA regulations
• 5 Watt RF output
• Ultra compact size
• Group scan and Priority channel watch
• Open memory scan
• Signal strength meter/ Power meter
• Priority channel memory
• Scan channel memory On/Off
• 5 Selectable call tones
• Multi function control for Audio Volume Channel selector and squelch level
• Built in Transmit Time Out Timer
• Signal monitoring
• Customized multi menu function.
* 38 Built in CTCSSS and 104 additional DCS codes that user selectable
* duplex capability
* Busy channel lock
* Roger Beep tone
* Key Beep tone
* 7 Backlight color
* Selectable LCD backlight level
* Scan resume time control (5, 10, 15, p5)
* LCD Flip for versatile mounting option
* Selectable Squelch delay time
5
Page 6
Controls and Connectors
Controls and Connectors
Front View
1. Microphone connector
2. Menu/Monitor
3. Scan/Memory On, Off
4. Power On/off, Channel & Volume and SQ control
Rear View
5. Antenna connection
6. Power supply connection
7. 3.5mm external jack for optional 8 ohm speaker
6
Page 7
Microphone (Part No. MIC300)
8. RJ45 microphone plug
9. Microphone rubber boot
10. Push To Talk (PTT) button
11. Volume down
12. INS and CALL
13. Volume up
14. Condensor mic.
Controls and Connectors
LCD Icons & Indicators
15
16
1819
15. Menu functiuon display
16. Memory indicator
17. Channel, Volume and
17
squelch level indicator
18. DPX indicator
19. Signal and power level
indicator
7
Page 8
Installation
Installation
Caution
When installing your radio in your vehicle, check that during installation
you do not damage any wiring or vehicle components that may be
hidden around the mounting position.
For optimum performance your radio needs to be installed correctly.
If you are unsure about how to install your radio, we suggest you
have your radio professionally installed by a UHF specialist or Auto
electrician. When installing the radio, avoid mounting it close to heaters
or air conditioners. Never press the PTT or CALL button before
connecting the antenna to the radio.
Screw the mounting bracket and microphone bracket to firm surfaces.
To install the radio:
1. Fix the radio bracket in a suitable location.
2. Then fix the radio in the bracket using the thumb screws.
Fitting the Microphone
The microphone uses RJ type telephone plug and socket:
1. position the microphone plug so the plastic flap faces downwards,
and press the plug into the socket unitl it ‘clicks’.
2. Gently press the rubber boot into the hole surrounding the socket
so that the slot around the boot fits neatly inside the rim of the entry
hole.
DC Power connection
The Radio is designed for 13.8 Volt DC, negative earth installations only
(i.e where the negative battery terminal connects to the chassis of the
vehicle). For installion on 24 volt system an inverter (not supplied) will
need to be used.
8
Page 9
Installation
Over voltage protection
The Radio ha a high voltage input detection system, to warn you if an
overvoltage situation occurs.
Example: if the power supply voltage exceeds 17 volts DC, the channel
display (LCD backlight) will flash in 7 different colors when the unit
is turned on. In addition, when transmitting, the TX RF power will
automatically select a low power output.
If the overvoltage warning appears, you must switch your radio off and
disconnect it from the power source, before locating the cause of the
trouble. The power source must not exceed 30 volts.
Wiring Methods
There are two possible wiring configurations for connecting to the
Vehicles power supply.
A. Radio stays ON when the ignition is switched OFF
Connect the radio’s negative (black) lead to the vehicle chassis, or
directly to the batteries negative terminal.
Connect the radio’s positive (red) lead via the 2 Amp fuse to the battery’s
positive terminal. Alternatively, the positive lead could be connected
at the fuse box at a point that has +13.8Volts continuously available
(preferably the battery side of the ignition switch) via the 2 Amp fuse.
B. Radio turns OFF with the ignition switch
Connect the radio’s negative(black) lead to the vehicle’s chassis, or
directly to the batteries negative terminal.
The radio positive(red) lead should connect to an accessory point in the
vehicle’s fuse box via the 2 Amp fuse.
9
Page 10
Installation
Antenna information
The antenna (not supplied) is of critical importance, to maximize your
output power and receiver sensativity.
A poorly installed, inferior quality antenna or one not designed for the
correct frequency band will give poor performance. You should only
purchase an antenna designed for the 477MHz frequency band.
Antenna installation
1. Connect the antenna to the rear antenna socket using a PL259 coaxial
connector (not supplied).
2. To obtain maximum performance from the radio, select a high quality
antenna and mount it in a good location.
Never press the PTT or CALL button before connecting the antenna
to the radio.
Optional accessory
If required you may install an external (8 ohm, minimum 5 Watt power)
speaker fitted with a 3.5mm plug (not supplied)
The jack is located on the rear of the radio.
10
Page 11
Operations
Operations
Power On/Off
Press and hold the power/Channel selector for 2 seconds. The default
channel is set to 01 and DPX on.
Volume control
Turn the channel selector clockwise to adjust the sound level for
comfortable reception. The Volume is set from level 1 to level 32.
On the microphone push the up or down buttons to increase or decrease
the volume, if held down the volume will increase or decrease quickly.
Selecting a channel
Press power/channel once. The channel digits display flashes. Select the
channel by rotating the channel knob up or channel down.
On the microphone push the INS button for instant selection of the
priority channel (factory default is set to 11).
11
Page 12
Operations
For your reference a list of the available channels, corresponding
frequencies and guidelines for their use and selection is printed
on page 21. For Australia, channels 05 and 35 are reserved for
Emergency calls.
Setting the Squelch Level
1. Press power/channel 2 times. The current squelch level is displayed.
2. Select the squelch level by rotating the squelch/channel control (sgl)
level up or channel down.
The radio has 7 preset (off - 7) squelch Levels.
Off - Squelch open
1- Max sensitivity (Min. squlech)
7- Min. sensitivity (Max/Tight squelch)
Menu
The Menu feature provides a convenient method of customising some
of the radio’s functions. The following menu options are available. Note
that some items are only available on certain channels.
1. Press and Menu/Monitor button. The first menu function displayed.
2. Press the Menu/Monitor button to cycle through each available
function. After the last function has been selected, the cycle returns to
the beginning.
3. Rotate the channel knob to alter the parameters of the selected function.
4. To save the changes and exit, press and hold Menu/Monitor button to
exit and store any changes.
12
Page 13
Operations
Menu list
* Use the channel knob to change the value of each setting.
* If a button is not pressed within 8 seconds the radio will automatically
exit the menu mode.
* Please see Menu modes
Functions Step Display Default
CTCS - 1 to 38
DCS - 1 to 104
Duplex On/Off ON - OFF
Scan mode
PRI setting
channel
Busy Channel
Lock
Roger Beep
Key Beep Tone
Melody Call
LCD backlight
level
CTC OFF to 38
DCS 1 to A4
On
Off
On
Off
ON - OFF
On
Off
On
Off
1
to
5
On
Off
Off
On
Open scan
Off
Off
Off
On
01
On
13
Page 14
Operations
Backlight LED
color
Scan delay time
SCt
Squelch release
delay Sdt
Flip
g, c, y, b,
r, p, w
P5 5 10 15
off 2 6 10 14
18 22
Top UP
Bottom UP
G
P5
off
Top UP
CTCSS and DCS setting
This feature allows you to receive signals only from callers who have
selected the same CTCSS and DCS code. DCS is similar to CTCSS. It
provides 104 extra, digitally coded, squelch codes that follow after the
38 CTCSS codes. CTCSS 1 - 38, followed by DCS 1 - 104 (displays A0 to
A4 for 100 to 104).
Duplex
General
Your radio has a Repeator Access function to allow use of local
repeator station (if available in your area). Repeaters are shared radio
systems installed by interested parties (clubs, local business etc.) that
transmissions on specific channels and re-transmit (or repeat) the
received signal to another channel.
C
h
a
n
Channel 32
Channel 2
Channel 32
14
Repeater Station
n
e
l 2
Page 15
Operations
The Repeator Access function can be set (from channel 1 to 8 and 41
to 48) used by local repeater stations. When activated, your radio will
receive the Repeator on its specific channel (all repeater outputs are
on channel 1 to 8 and 41 to 48) but transmit to the repeater channel
31 throgh 38 and 71 to 78 (Factory default is set to ON for all repeater
channels).
e.g.
CH01 on Duplex mode will receive on CH01 but transmit on CH31.
CH02 on duplex mode will receive on CH02 but transmit on CH32.
If you transmit on CH01 duplex mode, you are actually transmitting on
CH31; the repeater station down converts your signal and retransmits on
CH01.
Your UHF300 allows you to pre-select Duplex operation individually on
each channel.
CH and Number
1 476.425 477.175 CH31
2 476.450 477.200 CH32
3 476.475 477.225 CH33
4 476.500 477.250 CH34
5 476.525 477.275 CH35
6 476.550 477.300 CH36
7 476.575 477.325 CH37
8 476.600 477.350 CH38
41 476.4375 477.1875 CH71
42 476.4625 477.2125 CH72
43 476.4875 477.2375 CH73
44 476.5125 477.2625 CH74
45 467.5375 477.2875 CH75
46 476.5625 477.3125 CH76
47 476.5875 477.3375 CH77
48 476.6125 477.3625 CH78
Simplex mode Transmit/
reciever Frequency (MHz)
Duplex Mode transmit
Frequency(MHz)
15
Page 16
Operations
Open Scan (OS) Mode
The Open Scan feature scans for activity on all CB channels. Once a
channel is located, scanning will pause the will allow the signal to be
heard. As soon as the channel is clear and scan delay time has expired,
scanning will continue automatically.
Open Scan
Group Scan (GS) Mode
With Group Scan the Radio scans for activity, but in addition, it also
inserts your Priority Channel into the scan squence.
The means that your Priority Channel will be monitored regularly while
scanning to ensure that no calls are missed. Any signal received on your
Priority Channel will take precedence over any signals received on the
other channels.
GROUP OR PRIORITY SCAN
16
Page 17
Operations
Priority Channel
To store a Priority Channel, press the PRI button. The channel you
selected as your Priority Channel will then be automatically monitored
during the Group Scan.
Note: You can only store one channel as your priority channel.
Busy channel Lock
If the channel is already in use, you can prevent the UHF CB radio from
transmitting. This is particularly important when using CTCSS/DCS.
Roger Beep
This function emitts a beep on completition of transmission to alert the
other party that transmission has finisheds.
Key Beep
The Beep tone emits a tone when you press any of the buttons on the
microphone (except PTT button).
Call tone
You can select from 5 call tones this is the tone that is emitted when the
INS/CALL button on the microphone is pushed for 2 seconds.
Current regulations require calling tones to be restricted to one
transmission per minute. If a second transmission is attempted within
one minute then an error tone will sound.
17
Page 18
Operations
LCD Backlight level
You can reduce the brightness of the LCD backlight to be more
comfortable while driving at night.
7 Colour backlight
You can select from seven colour options for the LCD backlight. The
seven options are white, red, yellow, purple, cyan, blue and green.
Scan delay time
If 5, 10, or 15 sec is selected, SCAN will start again after 5, 10, or 15 sec
pause even though a signal is still present.
If P5 is selected, SCAN will stop as long as a signal is present and will
resume SCAN again 5 seconds later.
Squelch delay time
This is the time after the signal stops until the squelch mutes the audio.
It will be disabled when the scan function is selected.
The following delay times can be selected.
OF no delay
02 0.2 of a second
06 0.6 of a second
10 1 second
14 1.4 seconds
18 1.8 seconds
22 2.2 seconds
Flip LCD
You can flip the display for a convenient mounting position.
18
Page 19
Operations
Monitor
1. Press hold the Menu/Monitor button.
If no signal is present. A hissing noise will indicate an empty channel.
2. Press the Menu/Monitor button again to restore to it previous setting.
Scan
The radio SCAN function has the ability to allow programmable channels
to be scanned for groups of users.
When a signal is found, scanning will stop at that channel to allow the
signal to be heard, then resume scanning when the cahnnel is clear
again.
The scan resume time can be set as an optional pause of p5(default).
1. Press Scan button and scanning will start. The scan dirction can be
changed at any time by rotating the channel selector left or right.
2. To deactivate Scan, press Scan again.
Memory On/Off
1. Press and hold Scan/Mem button to store.
“•” will appear above the selected channel and short tone is heard.
2. To remove the channel from SCAN memory, press and hold Scan/
Mem button once again. The “•” icon disappears.
19
Page 20
Operations
Transmitting
NOTE: Before transmitting on any channel, listen to check the channel is
not already in use.
Transmitting
Select the desired channel. Press and hold the PTT button on the
microphone and speak normally into the microphone. Hold it approx.
7cm from your mouth. Release the PTT button to end the transmission
and listen for a reply.
Transmitting range
The talk range depends on the environment and terrain, it will be
affected by concrete structures and heavy foliage.
Optimal Range
Outdoors Flat, open
areas
Medium Range
Outdoors Buildings
or trees. Also near
residential buildings
Minimal Range Outdoors
Dense foliage or
mountains. Also inside
some buildings
Factory Reset
Turn Radio off press and hold both SCAN and MENU buttons then turn
radio on, this will reset all menu settings to defaults as listed on pages
13 and 14.
20
Page 21
UHF channels and frequencies
EMC Technologies (NZ) Ltd
Test Report No 101127.1
Report date: 25
th
November 2010
6.2 Nominal Carrier
Table 1 Nominal Carrier Frequency
Channel Frequency Table
Radiocommunications (Citizen Band Radio Stations)
Class Licence 2002
No licence is required to own or operate this radio in Australia and New Zealand.
The Radiocommunications (Citizen Band Radio Stations) Class Licence 2002
contains the technical parameters, operating requirements, conditions of licence
and relevant standards for Citizen Band (CB) radios. CB radios must comply with
the class licence for their use to be authorised under the class licence.
UHF channels and frequencies
IMPORTANT NOTE: The operation of your UHF radio in Australia and New
Zealand is subject to conditions in the following licenses:
In Australia the ACMA Radio communications (Citizen Band Radio Stations) and
in New Zealand by MED the General User Radio License for Citizen Band Radio.
Channel
01* 476.4250 476.4250 21 476.9250 476.9250
02* 476.4500 476.4500 22† 476.9500 476.9500
03* 476.4750 476.4750 23† 476.9750 476.9750
04* 476.5000 476.5000 24 477.0000 477.0000
05* 476.5250 476.5250 25 477.0250 477.0250
06* 476.5500 476.5500 26 477.0500 477.0500
07* 476.5750 476.5750 27 477.0750 477.0750
08* 476.6000 476.6000 28 477.1000 477.1000
9 476.6250 476.6250 29 477.1250 477.1250
10 476.6500 476.6500 30 477.1500 477.1500
11 476.6750 476.6750 31* 477.1750 477.1750
41* - 476.4375 61‡ — —
42* - 476.4625 62‡ — —
43* - 476.4875 63‡ — —
44* - 476.5125 64 477.0125 477.0125
45* - 476.5375 65 477.0375 477.0375
46* - 476.5625 66 477.0625 477.0625
47* - 476.5875 67 477.0875 477.0875
48* - 476.6125 68 477.1125 477.1125
49 476.6375 476.6375 69 477.1375 477.1375
50 476.6625 476.6625 70 477.1625 477.1625
Tx Rx
Freq Freq Freq Freq
MHZ MHz MHz MHz
Channel
Tx Rx
21
Page 22
UHF channels and frequencies
EMC Technologies (NZ) Ltd
Test Report No 101127.1
Report date: 25
th
November 2010
6.2 Nominal Carrier
Table 1 Nominal Carrier Frequency
Channel
Tx Rx
Channel
Tx Rx
Freq Freq Freq Freq
MHZ MHz MHz MHz
01* 476.4250 476.4250 21 476.9250 476.9250
41* - 476.4375 61‡ — —
02* 476.4500 476.4500 22† 476.9500 476.9500
42* - 476.4625 62‡ — —
03* 476.4750 476.4750 23† 476.9750 476.9750
43* - 476.4875 63‡ — —
04* 476.5000 476.5000 24 477.0000 477.0000
44* - 476.5125 64 477.0125 477.0125
05* 476.5250 476.5250 25 477.0250 477.0250
45* - 476.5375 65 477.0375 477.0375
06* 476.5500 476.5500 26 477.0500 477.0500
46* - 476.5625 66 477.0625 477.0625
07* 476.5750 476.5750 27 477.0750 477.0750
47* - 476.5875 67 477.0875 477.0875
08* 476.6000 476.6000 28 477.1000 477.1000
48* - 476.6125 68 477.1125 477.1125
9 476.6250 476.6250 29 477.1250 477.1250
49 476.6375 476.6375 69 477.1375 477.1375
10 476.6500 476.6500 30 477.1500 477.1500
50 476.6625 476.6625 70 477.1625 477.1625
11 476.6750 476.6750 31* 477.1750 477.1750
12 476.7000 476.7000 32* 477.2000 477.2000
13 476.7250 476.7250 33* 477.2250 477.2250
14 476.7500 476.7500 34* 477.2500 477.2500
15 476.7750 476.7750 35* 477.2750 477.2750
Channel 5 and 35 (paired for Duplex repeaters) are reserved as emergency
CTCSS and DCS will not operate on channels 5 and 35.
A list of currently authorised channels can be obtained from the ACMA website
16 476.8000 476.8000 36* 477.3000 477.3000
17 476.8250 476.8250 37* 477.3250 477.3250
18 476.8500 476.8500 38* 477.3500 477.3500
19 476.8750 476.8750 39 477.3750 477.3750
20 476.9000 476.9000 40 477.4000 477.4000
* The primary use for these channels is repeater operation using 750 kHz offset.
Channels 1-8 and 41-48 inclusive are used for mobile reception and channels 31-38
and 71-78 for mobile transmission. In addition, any designated repeater channel may
be used for simplex operation in areas where it is not used for repeater operation.
† Speech telephony is prohibited on these channels.
‡ At the time of production Channels 61, 62 and 63 are guard channels and are not
available for use.
channels and should be used only in an emergency.
51 476.6875 476.6875 71* 477.1875 -
52 476.7125 476.7125 72* 477.2125 -
53 476.7375 476.7375 73* 477.2375 -
54 476.7625 476.7625 74* 477.2625 -
55 476.7875 476.7875 75* 477.2875 -
56 476.8125 476.8125 76* 477.3125 -
57 476.8375 476.8375 77* 477.3375 -
58 476.8625 476.8625 78* 477.3625 -
59 476.8875 476.8875 79 477.3875 477.3875
60 476.9125 476.9125 80 477.4125 477.4125
in Australia and the MED website in New Zealand. Channel 11 is a calling
channel generally used to call others and channel 40 is the customary road
vehicle channel.
Once contact is established on the calling channel, both stations should move to
another unused "SIMPLEX" channel to allow others to use the calling channel.
Channels 22 and 23 are for Telemetry and Telecommand use, voice
communications are not allowed on these channels.
Channel 9 and above are the best choices for general use in Simplex mode.
22
Page 23
UHF channels and frequencies
38 CTCSS CODE LIST
CODE Frequency(Hz) CODE Frequency(Hz)
OFF OFF 20 131.8
1 67.0 21 136.5
2 71.9 22 141.3
3 74.4 23 146.2
4 77.0 24 151.4
5 79.7 25 156.7
6 82.5 26 162.2
7 85.4 27 167.9
8 88.5 28 173.8
9 91.5 29 179.9
10 94.8 30 186.2
11 97.4 31 192.8
12 100.0 32 203.5
13 103.5 33 210.7
14 107.2 34 218.1
15 110.9 35 225.7
16 114.8 36 233.6
17 118.8 37 241.8
18 123.0 38 250.3
19 127.3
23
Page 24
UHF channels and frequencies
DCS codes table
Code No.
1 023 36 223 71 445
2 025 37 225 72 446
3 026 38 226 73 452
4 031 39 243 74 454
5 032 40 244 75 455
6 036 41 245 76 462
7 043 42 246 77 464
8 047 43 251 78 465
9 051 44 252 79 466
10 053 45 255 80 503
11 054 46 261 81 506
12 065 47 263 82 516
13 071 48 265 83 523
14 072 49 266 84 526
15 073 50 271 85 532
16 074 51 274 86 546
17 114 52 306 87 565
18 115 53 311 88 606
19 116 54 315 89 612
20 122 55 325 90 624
21 125 56 331 91 627
22 131 57 332 92 631
23 132 58 343 93 632
24 134 59 346 94 654
25 143 60 351 95 662
26 145 61 356 96 664
27 152 62 364 97 703
28 155 63 365 98 712
29 156 64 371 99 723
30 162 65 411 100(do0) 731
31 165 66 412 101(do1) 732
32 172 67 413 102(do2) 734
33 174 68 423 103(do3) 743
34 205 69 431 104(do4) 754
35 212 70 432
DCS Code
(Octal)
Code No.
DCS Code
(Octal)
Code No.
DCS Code
(Octal)
24
Page 25
Customer Support
Customer Support
If you have any problems setting up or using this product you will nd useful tips and
information in the Troubleshooting section of this user guide as well as “Frequently
Asked Questions” on our website www.oricom.com.au.
If you have further questions about using the product after reviewing the resources
above or would like to purchase replacement parts or accessories please call our
Customer Support Team. Our dedicated local support team are more likely to be able
to help you than the retailer where you made your purchase.
Important
Please retain your purchase receipt and attach to the back page of this user guide as
you will need to produce this if warranty service is required. Take a few moments to
register your product online: www.oricom.com.au
25
Page 26
Warranty
How to make a claim under Warranty in Australia
Oricom has a simple warranty process for you to follow:
• PleasecalloremailourCustomerSupportTeam,contactdetailsfollow.
• ACustomerSupportTeammemberwillverifyaftertroubleshootingwithyouif
your product qualies under warranty. If so, they will give you a Product Return
Authorisation number.
• WewillthenemailorfaxaReturnAuthorisationformandaRepairNotice(if
necessary), together with instructions on how to return the goods for warranty
service.
Please note that if a Customer Support Team member advises that your product does
not qualify for return, this warranty does not apply to your product.
Products that are authorised to be returned to Oricom in Australia must include all of
the following:
• AcompletedReturnAuthorisationform
• AcopyofyourProofofPurchase(pleasekeepyouroriginalcopy)
• Thefaultyproduct,includingallaccessories.
Send the approved returns to:
Oricom International Pty Ltd
Locked Bag 658
South Windsor NSW 2756 Australia
Please note that this warranty excludes expenses incurred by you in returning any
faulty product to us. You must arrange and pay any expenses incurred (including
postage, delivery, freight, transportation or insurance of the product) to return the
faulty product to us, however, we will arrange delivery of the repaired or replaced
faulty product to you.
Important Information
Repair Notice
Please be aware that the repair of your goods may result in the loss of any usergenerated data (such as stored telephone numbers, text messages and contact
information). Please ensure that you have made a copy of any data saved on your
goods before sending for repair.
Please also be aware that goods presented for repair may be replaced by refurbished
goods or parts of the same type rather than being repaired.
26
Page 27
Warranty
Warranty Information (Australia)
This Warranty is provided by Oricom International Pty Ltd ABN 46 086 116 369, Unit 1,
4 Sovereign Place, South Windsor NSW 2756, herein after referred to as “Oricom”.
Oricom makes no other warranties or conditions, express or implied, including as
to acceptable quality and tness for a particular purpose, except as stated in this
Warranty.
Any implied warranties that may be imposed by law are limited in duration to the
Warranty Period.
Oricom warrants that the product is free from defects in materials or workmanship
during the Warranty Period. This Warranty does not extend to any product from which
the serial number has been removed or was purchased outside of Australia.
This warranty in no way affects your statutory warranty rights under the Competition
and Consumer Act 2010 or any other similar legislation.
The Warranty Period will be 3 years from the date of purchase of the product
evidenced by your dated sales receipt. You are required to provide proof of purchase
as a condition of receiving warranty services.
You are entitled to a replacement product or repair of the product according to the
terms and conditions of this document if your product is found to be faulty within
the Warranty Period. This Warranty extends to the original purchaser only and is not
transferable.
Rechargeable battery cells and rechargeable battery packs (if supplied) with this
product are covered under this warranty for a period of 90 days.
Products distributed by Oricom are manufactured using new materials or new and
used materials equivalent to new in performance and reliability. Spare parts may
be new or equivalent to new. Spare parts are warranted to be free from defects in
material or workmanship for thirty (30) days or for the remainder of the Warranty
Period of the Oricom branded product in which they are installed, whichever is longer.
During the Warranty Period, Oricom will where possible repair and if not replace
the faulty product or part thereof. All component parts removed under this Warranty
become the property of Oricom. In the unlikely event that your Oricom product has a
27
Page 28
Warranty
recurring failure, Oricom may, subject to the Competition and Consumer Act 2010, at
its discretion, elect to provide you with a replacement product of its choosing that is
at least equivalent to your product in performance.
Oricom does not warrant that the operation of the product will be uninterrupted or
error free.
Oricom is not responsible for damage that occurs as a result of your failure to follow
the instructions that came with the product. These terms and conditions together
with any specic terms and conditions contained in the user guide to the product
purchased constitute the complete and exclusive agreement between you and
Oricom regarding the product.
No change to the conditions of this Warranty is valid unless it is made in writing and
signed by an authorised representative of Oricom.
Oricom will not be in breach of a warranty expressly set out in this User Guide
or under the Competition and Consumer Act 2010 and excludes any liability for
damages or any other remedy arising under any other legislation or the common law
if the damage occurs as a result of:
1. failure by you to adhere to the warnings and follow the instructions set out in this
user guide for the proper installation and use of the product;
2. negligence on your part or misuse by you of the product;
3. an uncontrollable external cause which results in the product not functioning
including but not limited to power failure, lightning or over voltage; and
4. modication to the product or services carried out on the product by anyone other
than Oricom or Oricom’s authorised service provider.
Oricom will not be liable for any damages caused by the product or the failure of
the product to perform, including any lost prots or savings or special, incidental
or consequential damages. Oricom is not liable for any claim made by a third party
or made by you on behalf of a third party. This limitation of liability applies whether
damages are sought, or a claim made, under this Warranty or as a tort claim (including
negligence and strict product liability), a contract claim or any other claim. However,
this limitation of liability will not apply to claims for personal injury. Nothing in this
Warranty excludes, restricts or modies any condition, warranty, right or remedy
28
Page 29
Warranty
which pursuant to the Competition and Consumer Act 2010 applies to this Warranty
and which may not be so excluded, restricted or modied. For warranties that cannot
be excluded, restricted or modied, Oricom limits the remedies available to those
specied in the relevant legislation.
Oricom products come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
29
Page 30
Contact details for Oricom support and warranty claims in Australia
Oricom International Pty Ltd
Locked Bag 658
South Windsor, NSW 2756
Australia
Email: support@oricom.com.au
Phone: 1300 889 785
(Monday to Friday 8am to 6pm AEST)
Web: www.oricom.com.au
Fax: (02) 4574 8898
Contact details for Oricom support and warranty claims in New Zealand
Email: support@oricom.co.nz
Phone: 0800 674 266
(Monday to Friday 10am to 8pm NZST)
Web: www.oricom.co.nz
Ref: 13012012
Loading...