Orbit WaterMaster, 57114, 57414, 57416, 57116 Installation And Operating Instructions Manual
Introduction
Thank you for purchasing a quality WaterMaster®timer. You will enjoy many
years of satisfactory service, especially if proper installation and care is observed.
Please read the manual completely before installation, programming and operation. For ease of use, the manual is in step by step sequence of installing, setup
and operation.
The WaterMaster
®
timer keeps your yard beautiful whether you are at home or
away. WaterMaster
®
gives you convenience and flexibility, letting you use an
automatic watering program or override the automatic program for special
watering needs.
The WaterMaster
®
timer divides your property into four or six stations with
watering durations from 1 minute to 99 minutes each. You can water your yard
up to 3 times every day. Each start time will operate all stations in sequence.
You may use one of two watering schedules. One schedule will water on specific
days of the week. The other will water by periods - every other day or every 3rd
day. The WaterMaster
®
timer includes a manual override feature that allows you
to water all stations sequentially, or to manually water one station at a time.
Note: Illustrations in this booklet show only 4 station terminals & 4 stations on the
display. 6 station products are fitted with 6 station terminals & show 6 stations on
the display.
Note: Always check local plumbing and electrical codes for requirements when
installing the timer, transformer, and sprinkling system. Use only with household
current with an appropriate transformer matching your voltage and plug type.
Help
Before returning this timer to the store, contact Orbit®´Technical Service at:
1-800-488-6156.
Listings
The timer is tested to UL-1951 standard and is ETL®listed. Appropriate international models are CETL
®
and CE®approved.
Trademark Notice
WaterMaster®is a registered trademark of Orbit®Irrigation Products, Inc.
Installation
Timer Location
1.
Select a location that is near a standard electrical outlet. If this is not possible, a 16 gauge
electrical cord can be used to add length between the timer and the transformer (up
to several hundred feet). Avoid using an outlet controlled by an On/Off switch.
2. The timer should not be exposed to water or operated at temperatures below 14°
degrees or above 113° degrees Fahrenheit. (-10° c + 45° c)
Mounting the Timer
1. Screw a No. 8 screw at eye level leaving the screw
head extended out from the wall about 1/8 inch. Use
expanding anchors in plaster or masonry if necessary.
2. Slip the keyhole in the back of the timer over the
extended screw.
3. Screw a No. 8 screw through each of the two holes at
the bottom of the timer box into the wall. (See Figure 1.)
Wiring the Electric Valves
1. If the distance between the timer and
valves is under 700 feet, use WaterMaster
®
sprinkler wire or 20 gauge plastic jacketed
thermostat wire to connect the timer and
the valves. If the distance is over 700 feet,
use 16 gauge wire. The wire can be buried
in the ground; however, for more protection, wires can be pulled through PVC
pipe and buried underground. Be careful
to avoid burying the wires in locations
where they could be disturbed by digging
or trenching in the future.
2. Each valve has two wires. One wire is to be con-
nected as the common. All of the common wires for all the valves can be
connected together to one common wire going to the timer. The other valve wire
is to be connected to the specific station wire that is to control that valve.
(See Figure 2.)
3. All wires should be joined together using wire nuts, solder, or vinyl tape. For addi-
tional protection to waterproof connections, a WaterMaster
®
grease cap can be used.
4. To avoid electrical hazards, only one valve should be connected to each station.
5. The rated output is 24 volts AC at less than 0.240 Amps. Do not use solenoids
that exceed these values.
Installation
Connecting Valve Wires to the Timer
1. Remove cover by sliding it down.
2. Determine which valve you want to connect to
which station. Connect each valve wire to its station
terminal (labeled 1-6) by inserting the bare wire.
3. Connect the common wire to the terminal screw
labeled “COM”. (See Figure 3.)
Installing Batteries —For Program Back-Up
1. Install 2 AA (1.5 volt) alkaline batteries
in the battery compartment. (See Figure 4.)
CAUTION: Do not allow the battery to contact
the terminal strip.
2. With weak or no batteries, the program can
malfunction or be erased with power failure. If this happens, disconnect the
transformer, install fully charged batteries, plug in the transformer, and reprogram the timer.
Connecting the Transformer
1. With the cover off, find the two terminal
holes labeled “24V.” Make sure the transformer is not plugged in. Insert one of
the two power leads from the transformer
into each terminal hole and turn the
screw with a Phillips screwdriver until
wire is secure. Do not overtighten!
2. Plug in transformer. (See Figure 5.)
WARNING: Do not link two or more timers
together using a common transformer.
3. Slide the cover back on until it snaps.
Programming
Step 1—Setting Clock Time and Day of Week
1. Turn dial to
SET DAY
/
CLOCK
position.
2. Press and release
RESET button using a
pen or pencil. Display briefly shows all
functions then 12:00 PM with blinking
day of week indicator.
3. Press
NEXT
to advance the blinking
indicator to the current day of week.
(See Figure 6.)
4. Press
ENTER
to record current day of week.
Indicator stops blinking and time begins
blinking.
(See Figure 7.)
5. Press the + or – button to set the current
time of day. For faster setting press and
hold + or – button. Press
ENTER
to record current time of day.
Step 2— Setting Watering Cycle Start Times
Note: A cycle start time is the time of day that the timer begins watering the first station, and all other programmed stations will then follow in sequence. There are not
separate start times for each station. If you enter more than one cycle start time, all
stations programmed to operate will water again (in sequence).
1. Turn dial to
SET START TIMES
. Display
shows Start Time 1
in the left corner and -:— blinking.
2. Press + or – button to select the first
cycle start time. For faster setting press
and hold + or – button.
3. Press
ENTER
to record first start time. (See Figure 8.)
4. Press
NEXT
and repeat steps 2 and 3 if additional start times are required.
5. Press
CLEAR
to erase a start time.
6. The WaterMaster
®
Timer allows up to 3 start times per day. Do not set overlapping start times. One start time will activate each station in sequence. You
cannot set a cycle start time for each station. Generally only one cycle start
time is required.
Programming
Step 3— Setting Watering Durations for Each Station
You can assign each station an automatic watering period as short as 1 minute
and as long as 99 minutes.
1. Turn dial to
SET WATER DURATION
.
Display shows minutes blinking
––and station indicator
▼
on
Station 1.
2. Press + or – button to select
desired duration for the station.
For faster setting press and hold +
or – button.
3. Press
ENTER. Station indicator steps to Station 2. Display shows blinking ––.
(See Figure 9.)
4. Repeat steps 2 and 3 for stations 2 through 6 as applicable.
5. Press
CLEAR
to erase a station duration.
Step 4— Setting Watering Days
You decide which days of the week you want to water. You may choose to
water every day, every second day, every third day, or any combination of days
of the week.
1. Turn dial to
SET WATERING DAYS.
2. Press
NEXT
to move indicator to
the day you wish to water.
3. Press
ENTER to record the day.
(See Figure 10.) The indicator will
remain solid on the days assigned
to watering. The indicator will advance to the next day automatically and
blink after you press
ENTER
. To skip to the next day press
NEXT
.
4. Repeat steps 2 and 3 for other days as desired.
5. Press
CLEAR
to make the highlighted day a non-watering day.
1 2
Installation and Operating Instructions
For WaterMaster
®
4 and 6 Zone Timers
Sprinkler Timer
EVERY3rd2ndSuSFThWTM
1
2
3
S
T
A
R
T
1234ZONE MAN. DURATION
RESET
SET START TIMES
SET DAY/
CLOCK
SET
WATER
DURATION
SET
WATERING
DAYS
OFF
AUTO
MANUAL
+–
CLEAR NEXT
ENTER
INSTRUCTIONS
MODEL NUMBERS*
57114, 57116
57414, 57416
*WT2 VERSIONS
Wall
No. 8 Screw
Screwholes
Keyhole
Valves
Specific zone wire
Solenoids
Common Wires
Jacket
Figure 1
Figure 2
Figure 3
COM
1234
N.A. N.A. N.
A
To zone valve
Figure 4
COM
24V24V1234
N.A. N.A. N.A.
2 AA batteries
Figure 5
COM
24V24V1234
N.A. N.A. N.A.
Transformer
Figure 6
EVERY3rd2ndSuSFThWTM
S
T
A
R
T
1234ZONE MAN. DURATION
PM
1
2
3
SET DAY/
CLOCK
Figure 7
EVERY3rd2ndSuSFThWTM
S
T
A
R
T
1234ZONE MAN. DURATION
PM
1
2
3
Figure 8
EVERY3rd2ndSuSFThWTM
S
T
A
R
T
1234ZONE MAN. DURATION
AM
1
1
2
3
SET START TIMES
Figure 9
EVERY3rd2ndSuSFThWTM
S
T
A
R
T
1234ZONE MAN. DURATION
MINS
1
2
3
SET
WATER
DURATION
Figure 10
EVERY3rd2ndSuSFThWTM
S
T
A
R
T
1234ZONE MAN. DURATION
1
2
3
SET
WATERING
DAYS
http://waterheatertimer.org/Sprinkler-and-watering-timers.html
http://waterheatertimer.org/Woods-timers-and-manuals-old.html#raindrip
Programming
Step 5 — Setting Periodic Watering Schedule
Instead of selecting a particular day (or days) of the week, you may choose to
water every second day or every third day.
Note: If you have selected days of the week in step 4 you cannot select every 2nd or 3rd
day watering also.
1. Turn dial to
SET WATERING DAYS.
2. Press
CLEAR until blinking indi-
cator is pointing to either 2nd or
3rd day as desired. This clears
any settings on week days.
3. Press
ENTER. Indicator stops
blinking. (See Figure 11.) The
blinking indicator steps to the other selection.
Step 6 — Completing Automatic Operation
1. Turn dial to AUTO. Display shows cur-
rent time and day. (See Figure 12.)
Colon is blinking.
TIMER IS NOW PROGRAMMED AND
WILL OPERATE AUTOMATICALLY.
Manual Operation
The WaterMaster®Timer provides 2 separate manual settings. These manual settings will not alter the automatic setting during or after use.
All Stations Cycle Once
1. Turn dial to AUTO. Press MANUAL. Display
shows ALL, solid
▼ over stations with pro-
grammed durations, and
▼ over MANUAL.
(Ssee Figure 13.)
2. Press
ENTER. The timer will automatically
water all assigned stations in sequence for
the time assigned to each (a water droplet
drawing will appear on the display) and
then shut off and return to the automatic mode.
One Station Watering
1. Turn dial to AUTO. Press MANUAL.
2. Press
NEXT until indicator is on the station to
be watered. (See Figure 14.)
3. Press the + or – keys for the desired water-
ing duration— up to 99 minutes .
4. Press
ENTER. A water droplet drawing will
appear on the display. Timer will water for
the desired duration and return to the automatic mode.
To discontinue watering in the manual mode, press
CLEAR. Timer will return to
automatic mode.
Note: After
MANUAL has been pushed, if ENTER is not pushed within 10 seconds, the dis-
play will return to Time of Day.
Reviewing/Changing Settings
To Change Time and Current Day
1. Follow programming instruction in Programming section “Step 1.”
To Review Start Times
1. Turn dial to SET START TIMES.
2. The first start time will be displayed.
3. Press
NEXT to review remaining start times, if applicable.
4. To make changes, press + or – for any Start Time and follow instructions in
Step 2 of “Programming.”
To Review Watering Durations
1. Turn dial to SET WATER DURATION.
2. Station 1 duration will be displayed.
3. Press
NEXT to review other station durations.
4. To make changes, press + or – for any station duration and follow instruc-
tions in Step 3 of “Programming.”
To Review Watering Days:
1. Turn dial to SET WATERING DAYS. Display will show current settings.
2. To make changes, press
CLEAR on any day or schedule (to skip to the next day
press
NEXT.) Follow instructions in Step 4 and/or Step 5 of “Programming.”
Note: When watering begins, the display will show a water droplet and will count
down the programmed time on the display.
Other Features/Default
Stop the Automatic Watering for 24 hours
1. Turn the dial to AUTO.
2. Press
CLEAR. This will stop watering for 24 hours. An X appears on the display
to indicate that watering has been temporarily stopped or inhibited. The
number of hours remaining in the 24 hour period will appear on the display
and will count down to 1 hour.
3. To cancel the inhibit mode with the dial in the
AUTO position, press ENTER.
The X disappears and automatic watering resumes.
Note: This feature will work even during watering, but you must press
CLEAR twice.
System Shut Down
Turn dial to OFF position. Timer remains programmed but will not water. For
automatic rain shut-off, contact your WaterMaster
®
dealer to purchase a
WaterMaster
®
Model 57091 automatic rain shut-off switch.
Note: The rain shut-off easily connects to existing timer and prevents sprinklers from
watering during excessive rainfall.
System Reset
Using a pen and pencil, press and release RESET button to erase all programming.
Fuse
The 0.5 amp slow-blow fuse provides circuit protection. For replacement use
WaterMaster
®
fuses, Radio Shack®Part #270-1061, or equivalent.
Easy Access to Batteries
Two AA alkaline batteries.
Caution
In areas where heavy electrical equipment or lightning strikes are prevalent, an
“EMI Filter” is recommended. (Radio Shack #61-2791 or equivalent).
Default Program
In the event of a power failure and you have no batteries or your batteries are dead, the timer will revert to
the default program when power resumes. The clock
reverts back to 12:00 p.m. and each station will be
watered for 10 minutes when the clock shows 5:00
a.m. every day until reprogrammed.
If watering begins in the default mode, the display shows as illustrated. (See Figure 15.)
Troubleshooting
PROBLEM
POSSIBLE CAUSES
One or more valves do not turn on:
1. Faulty solenoid.
2. Wire broken or not connected.
3. Flow control stem screwed down, shutting valve off.
4. Programming is incorrect.
Continuous loss of program:
1. Battery is not hooked up.
2. Battery is too weak to keep the program in timer.
Stations turn on when they are not supposed to:
1. Water pressure is too high.
2. More than one start time is programmed.
One station is stuck on and will not shut off:
1. Faulty valve.
2. Particles of dirt or debris stuck in valve.
3. Valve diaphragm faulty.
All valves do not turn on:
1. Transformer defective or not connected.
2. Programming is incorrect.
3. Fuse blown.
Timer will not power up:
1. Fuse needs replacing.
Valves continue to turn on and off when they are not programmed to:
1. More than one start time is programmed with overlapping
schedules.
2. Excessive pressure.
Fuse blows repeatedly:
1. Short in wiring or solenoids.
2. Solenoid rating too high (max 24 VAC 240mA).
Troubleshooting
PROBLEM
POSSIBLE CAUSES
No Display/ Function:
1. Check that batteries are fresh and transformer is connected.
2. Press
RESET and reprogram.
Display locked up:
1. Check that batteries are fresh.
2. Press
RESET and reprogram.
Waters each station 10 mins at 5 am:
1. In default mode.
2. Press
RESET and reprogram.
Questions: Please call toll-free
1-800-488-6156
or visit us on the world wide web at
www.orbitonline.com
WaterMaster®Limited 2 Year Warranty
Orbit®Irrigation Products, Inc. warrants to its customers that its WaterMaster
®
products will be free from defects in materials and workmanship for a period
of two years from date of purchase. We will replace, free of charge, the defective part or parts found to be defective under normal use and service — for a
period of up to two years after purchase, proof of purchase required. We
reserve the right to inspect the defective part prior to replacement. Orbit
®
Irrigation Products, Inc. will not be responsible for consequential or incidental
cost or damage caused by the product failure. Orbit
®
Irrigation Products, Inc.
liability under this warranty is limited solely to the replacement or repair of
defective parts.
To exercise your warranty, return the unit to your dealer with a copy of the
sales receipt.
6 7 8
9 10
Figure 11
EVERY3rd2ndSuSFThWTM
S
T
A
R
T
1234ZONE MAN. DURATION
1
2
3
SET
WATERING
DAYS
Figure 12
AUTO
Figure 13
EVERY3rd2ndSuSFThWTM
S
T
A
R
T
1234ZONE MAN. DURATION
MINS
ALL
1
2
3
Figure 14
EVERY3rd2ndSuSFThWTM
S
T
A
R
T
1234ZONE MAN. DURATION
MINS
1
2
3
Figure 15
EVERY3rd2ndSuSFThWTM
S
T
A
R
T
1234ZONE MAN. DURATION
1
2
3
MINS
D
Orbit®Irrigation Products Inc.
845 North Overland Rd.
North Salt Lake, Utah 84054 ENGLISH
Printed in Hong Kong 57114-14 Rev B 5/99
Loading...