Optoma ZU610T-B, ZU610T-W User Manual

DLP® Projector

User’s Manual

2 English

TABLE OF CONTENTS

SAFETY .................................................................................................3

Regulation & Safety Notices .......................................................................................................5

INTRODUCTION ....................................................................................8

Package Overview .....................................................................................................................8

Product Overview .......................................................................................................................9

Main Unit .................................................................................................................................9

Control Panel .........................................................................................................................10

Connections .......................................................................................................................... 11

Remote Control ..................................................................................................................... 12

SETUP AND INSTALLATION ..............................................................14

Connecting Source to the Projector .........................................................................................14

Powering the Projector On/Off .................................................................................................16

Warning Indicator .................................................................................................................. 17

Adjusting the Projected Image .................................................................................................18

USER CONTROLS ..............................................................................21

Using the Control Panel ...........................................................................................................21

On-screen Display Menus ........................................................................................................22

How to operate ......................................................................................................................22

Structure ................................................................................................................................23

Picture ...................................................................................................................................27

Screen ...................................................................................................................................29

Settings .................................................................................................................................31

Volume ..................................................................................................................................32

Options ..................................................................................................................................33

3D ..........................................................................................................................................36

LAN .......................................................................................................................................37

APPENDICES ......................................................................................38

Projector Problems ................................................................................................................38

How to use web browser to control your projector ................................................................ 40

Crestron RoomView Control Tool .............................................................................................41

Installing and Cleaning the Optional Dust Filter ....................................................................... 43

Compatibility Modes ................................................................................................................. 44

Ceiling Mount Installation ......................................................................................................... 47

Optoma global ofces ...............................................................................................................48

English 3

SAFETY

The lightning ash with arrow head within an equilateral triangle is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufcient
magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the appli­ance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO
NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

Class B emissions limits

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regula­tions.

Important Safety Instruction

1. Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from over
heating, it is recommended to install the projector in a location that does not block ventilation. As an example,
do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure
such as a book case or a cabinet that restricts air ow.

2. Do not use the projector near water or moisture. To reduce the risk of re and/or electric shock, do not expose
the projector to rain or moisture.

3. Do not install near heat sources such as radiators, heaters, stoves or any other apparatus such as ampliers
that emits heat.

4. Clean only with dry cloth.

5. Only use attachments/accessories specied by the manufacturer.

6. Do not use the unit if it has been physically damaged or abused.
Physical damage/abuse would be (but not limited to):

 Unit has been dropped.
 Power supply cord or plug has been damaged.
 Liquid has been spilled on to the projector.
 Projector has been exposed to rain or moisture.
 Something has fallen in the projector or something is loose inside.

Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages
or other hazards.

7. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts
that could result in re or electric shock.

8. See projector enclosure for safety related markings.

9. The unit should only be repaired by appropriate service personnel.

4 English

Precautions

Please follow all warnings, precautions and maintenance as recommended in this user’s
guide.

▀■ Warning- Do not look into the projector’s lens when the light source is on. The bright light may hurt and damage

your eyes.

▀■ Warning- To reduce the risk of re or electric shock, do not expose this projector to rain or moisture.

▀■ Warning- Please do not open or disassemble the projector as this may cause electric shock.

▀■ Warning- Please do not open or disassemble the projector as this may cause electric shock.

Do:

Turn off and unplug the power plug from the AC outlet before cleaning the product.•
Use a soft dry cloth with mild detergent to clean the display housing.•
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.•

Do not:

Block the slots and openings on the unit provided for ventilation.•
Use abrasive cleaners, waxes or solvents to clean the unit.•
Use under the following conditions:•

- In extremely hot, cold or humid environments.
Sea level to 6000 feet



Extremely hot: > 35°C
Extremely cool: < 5°C

6000 feet above



Extremely hot: > 30°C
Extremely cool: < 5°C

Extremely humid: > 70% R.H. (Relative Humidity)



- In areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic eld.

- In direct sunlight.

3D Safety Information

Please follow all warnings and precautions as recommended before you or your child use the 3D function.

Warning

Children and teenagers may be more susceptible to health issues associated with viewing in 3D and should be
closely supervised when viewing these images.

Photosensitive Seizure Warning and Other Health Risks

- Some viewers may experience an epileptic seizure or stroke when exposed to certain ashing images or lights
contained in certain Projector pictures or video games. If you suffer from, or have a family history of epilepsy
or strokes, please consult with a medical specialist before using the 3D function.

- Even those without a personal or family history of epilepsy or stroke may have an undiagnosed condition that
can cause photosensitive epileptic seizures.

- Pregnant women, the elderly, sufferers of serious medical conditions, those who are sleep deprived or under
the inuence of alcohol should avoid utilizing the unit’s 3D functionality.

- If you experience any of the following symptoms, stop viewing 3D pictures immediately and consult a medical
specialist: (1) altered vision; (2) light-headedness; (3) dizziness; (4) involuntary movements such as eye or
muscle twitching; (5) confusion; (6) nausea; (7) loss of awareness; (8) convulsions; (9) cramps; and/ or (10)
disorientation. Children and teenagers may be more likely than adults to experience these symptoms. Parents
should monitor their children and ask whether they are experiencing these symptoms.

English 5

- Watching 3D projection may also cause motion sickness, perceptual after effects, disorientation, eye strain
and decreased postural stability. It is recommended that users take frequent breaks to lessen the potential of
these effects. If your eyes show signs of fatigue or dryness or if you have any of the above symptoms, imme­diately discontinue use of this device and do not resume using it for at least thirty minutes after the symptoms
have subsided.

- Watching 3D projection while sitting too close to the screen for an extended period of time may damage your
eyesight. The ideal viewing distance should be at least three times the screen height. It is recommended that
the viewer’s eyes are level with the screen.

- Watching 3D projection while wearing 3D glasses for an extended period of time may cause a headache or
fatigue. If you experience a headache, fatigue or dizziness, stop viewing the 3D projection and rest.

- Do not use the 3D glasses for any other purpose than for watching 3D projection.

- Wearing the 3D glasses for any other purpose (as general spectacles, sunglasses, protective goggles, etc.)
may be physically harmful to you and may weaken your eyesight.

- Viewing in 3D projection may cause disorientation for some viewers. Accordingly, DO NOT place your 3D
PROJECTOR near open stairwells, cables, balconies, or other objects that can be tripped over, run into,
knocked down, broken or fallen over.

Copyright

This publication, including all photographs, illustrations and software, is protected under international copyright
laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced
without written consent of the author.

© Copyright 2015

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations
or warranties with respect to the contents hereof and specically disclaims any implied warranties of merchantabil­ity or tness for any particular purpose. The manufacturer reserves the right to revise this publication and to make
changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such
revision or changes.

Trademark Recognition

Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending ap­plications in other countries throughout the world.

HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.

IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and
Windows are trademarks or registered trademarks of Microsoft Corporation.

Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated.

DLP, DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a trade­mark of Texas Instruments.

All other product names used in this manual are the properties of their respective owners and are Acknowledged.

Regulation & Safety Notices

This appendix lists the general notices of your projector.

FCC notice

This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.

6 English

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.

• Connect the device into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Notice: Shielded cables

All connections to other computing devices must be made using shielded cables to maintain compliance with
FCC regulations.

Caution

Changes or modications not expressly approved by the manufacturer could void the user’s authority, which is
granted by the Federal Communications Commission, to operate this projector.

Operation conditions

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference and

2. This device must accept any interference received, including interference that may cause undesired
operation.

Notice: Canadian users

This Class B digital apparatus complies with Canadian
ICES-003.

Remarque à l’intention des utilisateurs canadiens

Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.

Declaration of Conformity for EU countries

• EMC Directive 2004/108/EC (including amendments)

• Low Voltage Directive 2006/95/EC

• R & TTE Directive 1999/5/EC (if product has RF function)

Disposal instructions

Do not throw this electronic device into the trash when
discarding. To minimize pollution and ensure utmost protection
of the global environment, please recycle it.

English 7

Safety notice

COMPLIES WITH
21 CFR 1040.10 AND

1040.11 EXCEPT FOR
DEVIATIONS PURSUANT
TO LASER NOTICE No. 50,
DATED JUNE 24, 2007.
IEC/EN 60825-1:2007

LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT
WAVE LENGTH: 450-460 nm / MAX OUTPUT: 15.9 mW / PULSE DURATION: 1.25 ms
IEC 60825-1:2014 CLASS 1 LASER PRODUCT / RISK GROUP 2
Possibly hazardous optical radiation emitted from this product.
Do not stare into the beam, May be harmful to the eyes.

WARNING

- This product is classied as Class 2 of IEC 60825-1 : 2007 and also complies with 21 CFR 1040.10 and 1040.11
except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. IEC 60825-1:2014: CLASS 1 LA­SER PRODUCT - RISK GROUP 2

- Explanatory label is shown all information of laser power.

- This projector has built-in Class 4 laser module. Disassembly or modication is very dangerous and should never
be attempted.

- Any operation or adjustment not specically instructed by the user’s guide creates the risk of hazardous laser
radiation exposure.

- Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.

- Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.

- When turning on the projector, make sure no one within projection range is looking at the lens.

- Without following the control, adjustment or operation procedure may cause damage by the exposure of laser
radiation.

- Adequate instructions for assembly, operation, and maintenance, including clear warnings concerning precau­tions to avoid possible exposure to laser and collateral radiation in excess of the accessible emission limits in
Class 2.

- This projector is a Class 2 laser device that conforms with IEC 60825-1:2007 and CFR 1040.10 and 1040.11.

- Class 2 laser product, Do Not Stare Into Beam.

- This projector has built-in Class 4 laser module. Disassembly or modication is very dangerous and should never
be attempted.

- Any operation or adjustment not specically instructed by the user’s guide cre- ates the risk of hazardous laser
radiation exposure.

- Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.

- Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.

- Without following the control, adjustment or operation procedure may cause damage by the exposure of laser
radiation.

- Adequate instructions for assembly, operation, and maintenance, including clear warnings concerning precau­tions to avoid possible exposure to laser and collateral radiation in excess of the accessible emission limits in
Class 2.

8 English

INTRODUCTION

AA

AA

Package Overview

Unpack and inspect the box contents to ensure all parts listed below are in the box. If something is missing, please
contact your nearest customer service center.

Projector

AAA Batteries x2

Note: * For European warranty Information, please visit www.optomaeurope.com

Due to different applications in each country, some regions may have edifferent accessories.

Power Cord VGA Cable

CD User Manual



Warranty Card*



Basic User Manual



Documentation

Remote Control

English 9

INTRODUCTION

Product Overview

Main Unit

3

4

1

5

9

2

3

10

7

6

8

6

11

12

13

14

Note: Do not block projector inlet or outlet air vents.

No Item

1. Keypad

2. Focus Ring

3. Ventilation (inlet)

4. IR Receiver

5. Ventilation (outlet)

6. Speakers

7. Power Socket

3

No Item

8. Input / Output Connections

9. Lens

10. Tilt-Adjustment Foot

11. Kensington Lock

12. Lens Shift (vertical)

13. Lens Shift (Horizontal)

14. Lens lock

10 English

INTRODUCTION

Control Panel

21 4

8

7

3

5

6

9

No Item

1. On/Standby LED

2. Enter

3. Temp LED

4. Lamp LED

5. Menu

No Item

6. Source

7. Four Directional Select Keys

8. Power/Standby button

9. IR Receiver

English 11

INTRODUCTION

F1 F2

Connections

11 10 9 7 6 3 2 1

12

14 15 16

13

17

No Item

1. Microphone connector

2. Audio In connector

3. VGA In/ YPbPr connector

4. Audio Out connector

5. VGA Out connector

6. HDMI 1connector

7. HDMI 2/MHL connector

8. RS232C connector

9. USB-B mini connector

10. USB Power Out
(5V ---1.5A) Connector

4

8 5

No Item

11. HDBaseT connector (Depending
on Model)

12. RJ45

13. Power Socket

14. 3D Sync Out (5V) connector

15. Wired Remote connector

16. 12V Trigger connector

17. Kensington Lock

F1 HDMI3/MHL Connector
F2 USB Power

12 English

INTRODUCTION

Remote Control

No Item

1. Power On
Power on the projector.

2. Geometric Correction
Launch the Geometric Correction menu.

1

17

3. F1:Test pattern
Display a test pattern.

4. Display Mode
Select the display mode.

5. Four directional select keys
To select items or make adjustments.

6. Information
Display the projector information.

7. F3:Color Matching
Launch the Color Matching setting menu.

8. Input source selection
Select an input signal.

9. Menu
Launch the OSD menu. To exit OSD, Press
“Menu” again.

10. Volume Control -/+
Increase/decrease the volume.

11. Freeze
Freeze the projected image.

12. Format
Choose the projector format.

13. VGA
Switch to VGA source.

14. HDMI1
Switch to HDMI1 source.

10

11

12

13

14

15

2

3

4

5

6

7

8

9

18

19

20

21

22

23

24

25

26

27

28

15. HDBaseT (Depending on Model)
Switch to HDBaseT source.

16. 3D
Switch to 3D source.

17. Power Off

16

Power off the projector.

18. PIP/PBP Menu
Launch the PIP/PBP menu.

19. F2:LAN Settings
Launch the LAN Setting Menu.

Note: Some keys may have no function for models that do not support these features. I/O availability will vary depending

upon model and or SKU purchased.

English 13

INTRODUCTION

No Item

20. AV Mute
Momentarily turns off/on the audio and video.

21. Enter
Conrm your item selection.

22. Laser
Use as laser pointer.

23. Re-Sync
Automatically synchronize the projector to the
input source.

24. Digital Room -/+
Zoom in/out the projected image.

25. Remote ID / Remote all
Set the remote control ID.

26. HDMI2
Switch to HDMI2 source.

27. HDMI3 (Dongle)
Switch to HDMI3(Dongle) source.

28. Number Keypad (0~9)
Use as numeric keypad number “0~9”.

14 English

SETUP AND INSTALLATION

MOLEX

E62405SP

R

5

9

10

1

Connecting Source to the Projector

Connect to Computer/Notebook

Note:

Due to the difference in applications for each country, some regions may have different accessories.
(*) Optional accessory

Router / Network Switch

Microphone

External
Display

Audio Output

No Item

1. RS232 Cable

2. VGA Cable

3. HDMI Cable

4. USB Cable

5. Audio In Cable

No Item

6. RJ45 Cable

7. Power Code

8. VGA Out Cable

9. Audio Out Cable

10. Microphone cable

English 15

SETUP AND INSTALLATION

21

4

E62405SP

R

3

5

6

7

Connect to Video Sources

DVD Player, Set-top Box,

HDTV receiver

Microphone

Audio Output

No Item

1. HDMI Cable

2. Audio In Cable

3. Power Code

4. Audio Out Cable

No Item

5. Microphone cable

6. RJ-45 cable (Cat5 cable)

7. 12V DC Jack

8. HDMI3/MHL cable

Note:

Due to the difference in applications for each country, some regions may have different accessories.
(*) Optional accessory

16 English

SETUP AND INSTALLATION

Powering the Projector On/Off

Powering On the Projector

1. Securely connect the power cord and signal cable. When connected, the POWER/STANDBY LED will turn Red.

2. Turn on the lamp by pressing the “ ” button either on the projector or on the remote. At this moment, the

POWER/ STANDBY LED will now turn Blue. ①

The startup screen will display in approximately 6 sec- onds.

3. Turn on and connect the source that you want to display on the screen (computer, notebook, video player, etc).
The projector will detect the source automatically.

`

If you connect multiple sources at the same time, press the “INPUT” button on the control panel to switch
between inputs.

Note:

When the power mode is in standby mode (power consumption < 0.5W), the VGA output/Wire remote/LAN
will be deactivated when the projector is in standby. Audio out loop-through is always active in standby mode.
HDBaseT control is always deactivated in standby mode.

1

POWER/STANDBY

Note: Turn on the projector rst and then select the signal sources.

English 17

SETUP AND INSTALLATION

Powering Off the Projector

1. Press the “ ” button on the remote control or on the control panel to turn off the projector.
The following message will be displayed on the screen.

Press the “ ” button again to conrm otherwise the message will disappear after 10 seconds. When you press
the “ ” button for the second time, the fan will start cooling the system and will shut down.

2. The cooling fans continue to operate for about 4 seconds for cooling cycle and the POWER/STANDBY LED will
ash Red. When the POWER/STANDBY LED lights solid Red, the projector has entered standby mode.

If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply press “ ” button to restart the projector.

3. Disconnect the power cord from the electrical outlet and the projector.

Warning Indicator

LED lightning messages

When the warning indicators (see below) come on, the projector will automatically shutdown:

“LAMP” LED indicator is lit red and/or if “TEMP” LED indicator is lit red.


 “TEMP” LED indicator is lit red, this indicates the projector has overheated. Under normal conditions, the projec-

tor can be switched back on.

 “TEMP” LED indicator ashes red.

Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up again,
please contact your nearest service center for assistance.

Message

Standby State (LAN Off)

Standby State (LAN On)

Power On

Warning Up

Error(PowerGood NG)

Error (Fan fail)

Error (Over Temp)

Error (LD fail)

Power LED

Red Blue Red Red

On

On On

On

Flashing

Temp LED

On On

Flashing

On

Lamp LED

On

18 English

SETUP AND INSTALLATION

Adjusting the Projected Image

Adjusting the Projector’s Height

The projector is equipped with elevator feet for adjusting the image height.

1. Locate the adjustable foot you wish to modify on the underside of the projector.

2. Rotate the adjustable ring clockwise to raise the projector or counter clockwise to lower it. Repeat with the
remaining feet as needed.

Tilt-Adjustment Feet

Tilt-Adjustment Ring

English 19

SETUP AND INSTALLATION

To p View

Adjusting Projector Focus and Zoom

1. To adjust the image size, turn the zoom ring clockwise or anticlockwise to increase or decrease the projected
image size.

2. To adjust the focus, turn the focus ring clockwise or anticlockwise until the image is sharp and legible.
The projector will focus at distances (lens to wall) from 4.27 ~ 25.59 feet (1.3-7.8 meters).

Zoom

Focus

Lens Lock

Vertical lens shift

Front side door

Horizontal lens shift

Adjusting Projection Image Size (Diagonal)

Projection Image Size from 36” to 300” (1.09~9.09 meters).

Open the front side door of the projector.1.
Unlock the lens lock, before adjust the lens shift.2.
Turn the vertical/horizontal lens shift knob to shift the lens3.
Turn the lens lock clockwise to lock the lens in place 4.
( Lens shift knob still can be rotated.)
Close the front side door of the projector.5.

Note: The stroke for lens shift is designed to be regular triangle, when lens are adjusted to central position horizon-

tally, lens can be vertically shifted to the highest point

Top View

Side View

Projection Distance (D)

Projection Distance (D)

Screen

Screen

Screen (W)

Screen (H)

Offset (Hd)

Diagonal

Height

Width

20 English

SETUP AND INSTALLATION

10%

20%

10%

(Hd)

(D)

Width

Height

Lens shift position

20%

image size Screen Size WxH Projection Distance (D) Offset (Hd)

inch cm inch cm inch cm inch

Diagonal Width Height Width Height Wide Tele Wide Tele Wide Tele Wide Tele

36" 78.0 49.0 30.7 19.3 NA 170.0 NA 66.9 20.1 20.1 7.9 7.9

100" 215.0 135.0 84.6 53.1 260.0 460.0 102.4 181.1 37.4 37.4 14.7 14.7

WUXGA 16:10

150" 323.0 202.0 127.2 79.5 390.0 690.0 153.5 271.7 50.8 50.8 20.0 20.0

200" 431.0 269.0 169.7 105.9 520.0 920.0 204.7 362.2 64.3 64.3 25.3 25.3

250" 539.0 337.0 212.2 132.7 640.0 NA 252.0 NA 77.8 77.8 30.6 30.6

300" 646.0 404.0 254.3 159.1 770.0 NA 303.1 NA 91.2 91.2 35.9 35.9

 This table is for user’s reference only.

center of lens

Image Offset

English 21

USER CONTROLS

Using the Control Panel

Name

POWER

Enter Conrm a selected item.

INPUT

MENU

Four Directional
Select Keys

LAMP LED

TEMP LED

ON/STANDBY

LED

Refer to the “Power On/Off the Projector” section on pages 16-

17.

Select an input signal

Launch the on-screen display (OSD) menu. To exit OSD, press
“MENU” again.

Use ▲▼◄► to select items or make adjustments to your selec­tion.

Refer to the LED indicator of the projector light source status.

Refer to the LED indicator of the projector temperature status.

Refer to the LED indicator of the projector power status.

Description

22 English

USER CONTROLS

On-screen Display Menus

The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a
variety of settings.

How to operate

To open the OSD menu, press “Menu” on the Remote Control or Projector Keypad.1.

When OSD is displayed, use ▲▼ 2. keys to select any item in the main menu. While making a selection on a
particular page, press the ► or “Enter” key to enter sub menu.

Use the 3. ▲▼ keys to select the desired item and adjust the settings using the ◄► key.

Select the next item to be adjusted in the sub menu and adjust as described above.4.

Press “Enter” to conrm.5.

To exit, press “Menu” again. The OSD menu will close and the projector will automatically save the new settings.6.

Main Menu

SettingsSub Menu

English 23

USER CONTROLS

Structure

Note: Please note that the on-screen display (OSD) menus vary according to the signal type selected and the pro-

jector model you are using.

Main Menu Sub Menu Setting

Bright/Presentation/Movie/sRGB/Blending/DICOM SIM./User

Picture

Screen

Color Mode

Wall Color White/ Light Yellow/ Light Blue/ Pink/ Dark Green

Brightness

Contrast

Sharpness

Saturation

Hue

Gamma Film/Graphics/1.8/2.0/2.2/2.6/Blackboard/DICOM SIM

Color Temp 5500K/6500K/7500K/8500K/9500K

White/Red/

Color Matching

Dynamic Black On / Off

Color Space

Aspect Ratio Auto/4:3/16:9/16:10

Phase

Clock

H.Position

V.Position

Digtial Zoom

Projection Front/Front Ceiling/Rear/Rear Ceiling

Geometric
Correction

PIP-PBP Settings

Green/Blue/Cyan/

Magenta/Yellow

V. Keystone

H. Keystone

4 Corners On/Off

Grid Color Purple/Green

Reset Yes/No

Function PBP/PIP/ Off

Main Source VGA/HDMI-1/HDMI-2/Dongle/HDBaseT

Sub Source VGA/HDMI-1/HDMI-2/Dongle/HDBaseT

Location Top Left/Top Right/Bottom Left/Bottom Right

Size Small/Medium/Large

Swap

(Change Color Mode to User Mode if customer changes the
settings)

(For VGA component signal only)

(VGA component signal only)

Hue/ Saturation /Gain

Not HDMI Input: Auto/RGB/YUV

HDMI Input: Auto/RGB(0~255)/RGB(16~235)/YUV

24 English

USER CONTROLS

Main Menu Sub Menu Setting

Language

English/German/French/Italian/Spanish/Polish/Swedish/
Dutch/Portugese/Japanese/Traditional Chinese/ Simplied
Chinese /Korean/Russian/Arabic/Norsk/Turkish/Danish/
Finnish/Greek/Hungarian/Czech/Romania/Thai/Farsi/Vietnam
/Indonesian/Slovakian

Settings

Volume

Menu Location Left Top, Right Top, Center, Left Bottom, Right Bottom

VGA OUT
(Standby)

LAN (Standby) Off/On

Test Pattern None / Grid / White

Direct Power On On/Off

Reset to Default Yes/No

Speaker On/Off

Audio Out On/Off

Microphone On/Off

Mute On/Off

Volume

Microphone
Volume

EQ

Off/On

English 25

USER CONTROLS

Main Menu Sub Menu Setting

Logo Default/User

Logo Capture

Auto Source On/Off

Input VGA, HDMI-1, HDMI-2, Dongle, HDBaseT

Auto Power Off
(Min.)

Sleep Timer (Min.)

SSI Settings

SSI Power Mode Normal,ECO

High Altitude On/Off [Default Off]

Optional Filter

Installed

Optional Filter
Settings

Security

Options

Remote Settings

HDBaseT Control

PIP-PBP Module

Information Hide On / Off

Information

Filter Usage

Filter Reminder

Cleaning Up

Reminder

Security On / Off

Security Timer Month / Day / Hour

Change

Password

IR Function On / Off

Remote Code 00 ~ 99

HDBaseT

Hours

Auto

SSI Hours Used (Normal)

SSI Hours Used (ECO)

Yes/No

Read-Only

Yes/No

Version

HDMI EQ

Reset

USB Upgrade

Model Name

SNID

Source (Main Source / Sub Source)

Main Source Resolution

Sub Source Resolution

SW Version (DDP/MCU/LAN)

Aspect Ratio

SSI Hours (Normal/Eco)

IP Address

Network Status

Remote Code

Remote Code (Active)

26 English

USER CONTROLS

Main Menu Sub Menu Setting

3D Auto/On

3D Invert On/Off

3D

Network

3D Format

1080p @ 24 96Hz/144Hz

Status

DHCP Client On/Off

IP Address

Subnet Mask

Gateway

DNS

Store

MAC Address

Group Name

Projector Name

Location

Contact

Frame Packing

Side-by-Side (Half)

Top amd Bottom

Frame Sequential

Field Sequential

English 27

USER CONTROLS

Picture

Color Mode

There are many factory presets optimized for various types of images. Use the ◄ or ► button to select the item.

Bright: For brightness optimization.•

Presentation: For meeting presentation.•

Movie: For playing video content.•

sRGB: For game content.•

Blending: For blending application.•

DICOM Sim:•

User: Memorize user’s settings.•

Wall Color

Use this function to obtain an optimized screen image according to the wall color. You can select from “White”, “Light
Yellow”, “Light Blue”, “Pink”, and “Dark Green”.

Brightness

Adjust the brightness of the image.

Press the ◄ button to darken image.•

Press the ► button to brighten image.•

Contrast

The Contrast controls the difference between the lightest and darkest parts of the picture. Adjusting the contrast
changes the amount of black and white in the image.

Press the ◄ button to decrease the contrast.•

Press the ► button to increase the contrast.•

Sharpness

Adjust the sharpness of the image.

Press the ◄ button to decrease the sharpness.•

Press the ► button to increase the sharpness.•

Note: “Sharpness”, “Sat- uration” and “Hue” functions are only supported under video mode.

28 English

USER CONTROLS

Saturation

Adjust a video image from black and white to fully saturated color.

Press the ◄ button to decrease the amount of saturation in the image.•

Press the ► button to increase the amount of saturation in the image.•

Hue

Adjust the color balance of red and green.

Press the ◄ button to increase the amount of green in the image.•

Press the ► button to increase the amount of red in the image.•

Gamma

This allows you to adjust the gamma value to obtain the better image contrast for the input.

Color Temp

This allows you to adjust the color temperature. At higher temperature, the screen looks colder; at lower
temperature, the screen looks warmer.

Color Maching

Use these settings for advanced adjustment of the individual Red,Green,Blue,Cyan,Magenta and Yellow and White
Colors.

Dynamic Black

Use this function to increase the contrast ratio.

Color Space

Select an appropriate color matrix type from AUTO, RGB, RGB(0-255), RGB(16-235) or YUV.

Note: “RGB (0-255)” and “RGB (16-235)” are only supported for HDMI source.

English 29

USER CONTROLS

Screen

Aspect Ratio

Auto: Keep the image with original width-height ratio and maximize the image to t native horizontal or •
vertical pixels.

4:3: The image will be scaled to t the screen and displayed using a 4:3 ratio.•

16:9: The image will be scaled to t the width of the screen and the height adjusted to display the image •
using a 16:9 ratio.

16:10: The image will be scaled to t the width of the screen and the height adjusted to display the image •
using a 16:10 ratio.

Phase

Synchronize the signal timing of the display with the graphic card. If the image appears to be unstable or ickers,
use this function to correct it.

Note: Phase, Clock, H. Position, V. Position adjustment only support VGA Graphic.

Clock

Adjust to achieve an optimal image when there is a vertical icker in the image.

H. Position

Press the ◄ button to move the image left.•

Press the ► button to move the image right.•

V. Position

Press the ◄ button to move the image down.•

Press the ► button to move the image up.•

Digital Zoom

Press the ◄ button to reduce the size of an image.•

Press the ► button to magnify an image on the projection screen.•

30 English

USER CONTROLS

Projection

Front: The image is projected straight on the screen.•

Front Ceiling: This is the default selection. When selected, the image will turn upside down.•

Rear: When selected, the image will appear reversed.•

Rear Ceiling: When selected, the image will appear reversed in upside down position.•

Geometric Correction

H Keystone

•
Press the ◄ or ► button to adjust image distortion horizontal. If the image looks trapezoidal, this option can
help make the image rectangular.

V Keystone

•
Press the ◄ or ► button to adjust image distortion vertically. If the image looks trapezoidal, this option can
help make the image rectangular.

4 Corners

•
Adjust the image 4 corners pixel by pixel to make the image rectan- gular.

Grid Color

•
Set 4 corners correction function grid color.

Reset

•
Set H/V Keystone, 4 corners parameters to default values.

PIP-PBP Settings

Function: To enable/disable PIP/PBP function.•

Main Source: To set PIP/PBP main source.•

SUb Source: To set PIP/PBP sub source.•

Location: To set PIP sub source location.•

Size: To set PIP sub source size.•

Swap: To swap PIP/PBP main/sub source.•

Some source/signal combinations may not be compatible with PIP/PBP function. Please refer to the table below:

Matrix

HDMI-1 - V V - V

HDMI-2 V - - V V

Dongle V - - V V

HDBaseT - V V - V

VGA V V V V -

1. Flashing lines may occur if the bandwidth of both inputs are too high, please try to reduce the resolution.

2. Frame tearing may occur due to a difference in frame rate between the Main and the Sub picture, please try to
match the frame rate for each input.

HDMI-1 HDMI-2 Dongle HDBaseT VGA

English 31

USER CONTROLS

Settings

Language

Choose the multilingual OSD menu. Press the ◄ or ► button into the sub menu and then use the ▲ or ▼ button to
select your preferred language. Press ► on the remote control to nalize the selection.

Menu Location

Choose the menu location on the display screen.

VGA Output (Standby)

Choose “On” to enable VGA OUT connection.

LAN (Standby)

Choose “On” to enable LAN connection. Choose “Off” to disable LAN connection.

Test Pattern

Display a test pattern.

Direct Power On

Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied,
without pressing the

Reset

Choose “Yes” to return the parameters on all menus to the factory default settings.

key on the projector control panel or on the remote control.

32 English

USER CONTROLS

Volume

Speaker

Choose “On” to enable the speaker.•

Choose “Off” to disable the speaker.•

Line Out

Choose “On” to enable the line out function.•

Choose “Off” to disable the line out function.•

Microphone

Choose “On” to enable the microphone.•

Choose “Off” to disable the microphone.•

Mute

Choose “On” to turn mute on.•

Choose “Off” to turn mute off.•

Volume

Press the ◄ button to decrease the volume.•

Press the ► button to increase the volume.•

Microphone Volume

Press the ◄ button to decrease the microphone volume.•

Press the ► button to increase the microphone volume.•

EQ

Set audio EQ values.

English 33

USER CONTROLS

Options

Logo

Use this function to set the desired startup screen. If changes are made they will take effect the next time the
projector is powered on.

Default: The default startup screen.•

User: Use stored picture from “Logo Capture” function.•

Logo Capture

Press ► button to capture an image of the picture currently displayed on screen.

Note:

For successful logo capture, please ensure that the on-screen image does not exceed the projector’s native
resolution.
“Logo Capture” is not available when 3D is enabled.
Before active this function, it is recommended that “Aspect Ratio” is set to the “Auto”.

Auto Source

On: The projector will search for other signals if the current input signal is lost.•

Off: The projector will only search current input connection.•

Input

Press ► button to enable/disable input sources. The projector will not search for inputs that are not selected.

Auto Power Off (Min)

Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the
projector. The projector will automatically power off when the countdown has nished (in minutes).

34 English

USER CONTROLS

Sleep Timer

Sets the countdown timer. The countdown timer will start, with or without a signal being sent to the projector. The
projector will automatically power off when the countdown has nished (in minutes).

SSI Settings

SSI Hours Used (Normal)

•
Display the projection time of normal mode.

SSI Hours Used (ECO)

•
Display the projection time of ECO mode.

SSI Power Mode

•
Normal: Normal mode.
ECO: Use this function to dim the projector SSI which will lower power consumption and extend the SSI life.

High Altitude

On: The built-in fans run at high speed. Select this option when using the projector at altitudes above 2500•
feet/762 meters or higher.

Off: The built-in fans automatically run at a variable speed according to the internal temperature.•

Optional Filters Remind (Hour)

Optional Filter Installed: Filter is installed or not.•

Filter Usage Hours: Hours of lter had been used.•

Filters Remind (Hour): Set the lter reminder time.•

Cleaning Up Remind: Select “Yes” to reset the dust lter hour counter after replacing or cleaning the dust•
lter.

Security

Security: Choose “On” to use security verication when turning on projector. Choose “Off” to be able to•
switch on the projector without password verication.

Security Timer

•
Use this function to set the how long (Month/Day/Hour) the projector can be used. Once this time has
elapsed you will be requested to enter your password again.

Change Password•

First time:

1. ” to set the password.

Press “
The password has to be 6 digits.2.
Use number button on the remote to enter your new password and then press “3. ” key to conrm your
password.

Change Password:

1. ” to input old password.

Press “
Use number button to enter current password and then press “2. ” to conrm.
Enter new password (6 digits in length) using the number buttons on the remote, then press “3. ” to
conrm.
Enter new password again and press “

4. ” to conrm.
If the incorrect password is entered 3 times, the projector will automatically shut down.•

If you have forgotten your password, please contact the dealer for support.•

USER CONTROLS

Note:

Password default value is “000000” (first time).
Always keep the password in your files. If the password is forgotten or lost, please contact your local autho­rized service center.

Remote Setting

IR function: When this function is “Off”, the projector cannot be operated by the remote control.



Remote code: 00~99, default code (common code): 00



HDBaseT Control

The projector will automatically detect the signal from HDBaseT transmitter supplied. Choose “HDBaseT” to

•
activate Direct Power mode.

When HDBaseT control is ON, 12v trigger output signal will always be ON, even if the

•
projector is on Standby mode.

PIP-PBP Module

Version: Show PIP-PBP module software version.•

Reset: Reset the PIP-PBP module.•

USB Upgrade: Upgrade the PIP-PBP module software.•

HDMI EQ: Set PIP-PBP module HDMI port EQ value.•

Information Hide

On: Choose “On” to hide the info message.•

Off: Choose “Off” to show the “info” message.•

Information

Display the projector information for model name, SNID, source, resolution, software version, aspect ratio, SSI

Hours, IP Address and Network Status on the screen.

Signal Power On & HDBaseT Standby

To access Signal Power On and HDBaseT Standby menu -- with projector on press the following buttons (in order):
Power > Up >Down> Menu.

Signal Power On

On: Choose “On” to enable Signal Power On.•

Off: Choose “Off” to disable Signal Power On.•

HDBaseT Standby

On: Choose “On” to enable HDBaseT Standby.•

Off: Choose “Off” to disable HDBaseT Standby.•

English 35

36 English

USER CONTROLS

3D

3D

Auto: When a HDMI 1.4a 3D timing identication signal is detected, the 3D image is selected automatically.

Choose “On” to enable 3D function.•

Choose"Auto" to detected 3D signal automatically.•

3D Invert

If you see a discrete or overlapping image while wearing DLP 3D glasses, you may need to execute “Invert” to get
best match of left/right image sequence to get the correct image.

3D Format

Use this feature to select the 3D format. Options are: “Frame Packing”, “Side-by-Side (Half)”, “Top and Bottom”,
“Frame Sequential”.

1080p@24

Use this feature to select 96 or 144Hz refresh rate as using 3D glasses in the1080p @ 24 frame packing.

English 37

USER CONTROLS

LAN

Status

Display the network connection status.

DHCP

Congure the DHCP settings.

On: Choose “On” to let the projector to obtain an IP address automatically from your network.•

Off: Choose “Off” to assign IP, Subnet Mask, Gateway, and DNS conguration manually.•

IP Address

Display an IP address.

Subnet Mask

Display the subnet mask number.

Gateway

Display the default gateway of the network connected to the projector.

DNS

Display the DNS number.

MAC Address

Display the MAC address.

Group Name

Display the group name.

Projector Name

Display the projector name.

Location

Display the projector location.

Contact

Display the contact information.

38 English

APPENDICES

Projector Problems

The projector stops responding to all controls

If possible, turn off the projector, then unplug the power cord and wait at least 60 seconds before reconnect- `
ing power.

`

Check that “Keypad Lock” is not activated by trying to control the projector with the remote control.

If the remote control does not work

Check if the operating angle of the remote control is within ±30° both `
horizontally and vertically on one of the IR receivers on the projector.

`

Make sure there is no obstruction between the remote control and the projector. Move to within 12 m (±0°)
of the projector.

`

Make sure the batteries are inserted correctly.

`

Replace batteries if they are exhausted.

`

Ensure that you have set your remote to the correct IR code setting.

When making a direct connection from your computer to the projector

If you have network connection problem from your computer to the projector, please refer to the computer `
setting as below or contact with web administrator.

Step 1: Find an IP Address (192.168.0.100) from LAN function of projector.

Step 2: Select “Apply” and push the “Enter” button. Once the setting is saved, exit the OSD by pushing

“Menu” button.

Step 3: To open Network Connections, click Start, click Control Panel, click Network and Internet

Connections, and then click Network Connections. Click the connection you want to congure, and
then, under Network Tasks

Step 4: On the General tab, under This connection use the following items, click Internet Protocol(TCP/

IP), and then click “Properties”.

, click Change settings of this connection.

English 39

APPENDICES

Step 5: Click Use the following IP address, and type in as below:

1) IP address: 192.168.0.101

2) Subnet mask: 255.255.255.0

3) Default gateway: 192.168.0.254

Step 6: To open Internet Options, click IE web browser, click Internet Options, click the Connections tab

and click “LAN Setting…”.

Step 7: All items in the Local Area Network (LAN) Setting window must unchecked. Then click “OK” button

twice.

Step 8: Open your IE and type in the IP address of 192.168.0.100 in the URL then press “Enter” key.

40 English

APPENDICES

How to use web browser to control your projector

1. Turn on DHCP to allow a DHCP server to automatically assign an IP, or manually enter the required network
information.

2. Then choose apply and press button to complete the conguration process.

3. Open your web browser and type in IP Address from the OSD LAN screen then the web page will display as
below:

Note: When you used the projector IP address, you will can not link to your service server.

4. Based on network web-page for the input-string in [tools] tab, the limitation for Input-Length is in the below list
(“space” and the other punctuation key included):

Category Item

Crestron Control

Projector

Network

Conguration

User Password

Admin Password

IP Address 15

IP ID 2

Port 5
Projector Name 10
Location 9
Assigned To 9
DHCP (Enabled) (N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
Enabled (N/A)
New Password 15
Conrm 15
Enabled (N/A)
New Password 15
Conrm 15

Input-Length

(characters)

English 41

APPENDICES

Crestron RoomView Control Tool

Crestron RoomView™ provides a central monitoring station for 250+ control systems on a single Ethernet network
(more are possible, the number depends on the combination of IP ID and IP address). Crestron RoomView
monitors each projector, including projector’s online status, system power, lamp life, network setting and hardware
faults, plus any custom attribute as dened by the Administrator.

The Administrator can add, delete, or edit room information, contact information and events, which are logged auto­matically by the software for all users. (Operation UI as following image)

Note: Crestron RoomView function support is dependent on models.

When using RS232 or LAN control commands to power on the
projector, there will be a feedback delay of 6 to 10 seconds.

Main Screen1.

Edit Room2.

On the “Edit Room” page, enter the IP Address (or hostname) as shown on the projector’s on-screen display
(OSD) menu, and “02” for IPID, “41794” for the reserved Crestron control port.

About Crestron RoomView™ setting and command method, please access below website to get RoomView™
User Guide and more information:
http://www.crestron.com

42 English

APPENDICES

Edit Attribute3.

Edit Event4.

For more information, please visit
http://www.crestron.com & www.crestron.com/getroomview.

Network supports Crestron (Room View), AMX (Device Discovery) , PJLink and RS232 control.

English 43

APPENDICES

1

2

3

Installing and Cleaning the Optional Dust Filter

We recommend you clean the dust lter every 500 hours of operation, or more often if you are using the projector
in a dusty environment.

When the warning message appears on the screen, do the following to clean the air lter:

Note:

The optional dust lter should be used in dusty environments.
If the dust lter is installed, a proper maintenance will prevent overheat- ing and projector malfunction.
The dust lter is optional.
The specic inter- faces are selected in terms of the specications of types.

Air Filter Cleaning Procedure:

1. Switch off the power to the projector by pressing the “ ” button.

2. Disconnect the power cord.

3. Pull out the dust lter, as shown in the illustration.①

4. Carefully remove the dust lter. Then clean or change the lter. ②

To install the lter, reverse the previous steps.

5. Turn on the projector and reset the lter usage counter after the dust lter is
replaced.

44 English

APPENDICES

Compatibility Modes

A. VGA Analog

(1) PC Signal

Modes Resolution

VGA 640x480 60 31.5

640x480 67 35.0 26.8 Established Timings 1

640x480 72 37.9

640x480 75 37.5

640x480 85 43.3

IBM 720x400 70 31.5 28.3 Established Timings 1

SVGA 800x600 56 35.1

800x600 60 37.9

800x600 72 48.1 50.0 Established Timings 2

800x600 75 46.9 49.5 Established Timings 2

800x600 85 53.7 56.3

Apple, Mac II 832x624 75 49.1 57.3 Established Timings 2

XGA 1024x768 60 48.4 65.0

1024x768 70 56.5 75.0 Established Timings 2

1024x768 75 60.0 78.8 Established Timings 2

1024x768 85 68.7 94.5

1024x768 120 99.0 137.8 Standard Timing Identication

Apple, Mac II 1152x870 75 68.7 100.0 Manufacturer’s Reserved Timing

SXGA 1280x1024 60 64.0 108.0

1280x1024 72 77.0 133.0

1280x1024 75 80.0 135.0 Established Timings 2

QuadVGA 1280x960 60 60.0 101.3 Standard Timing Identication

1280x960 75 75.2 130.0

SXGA+ 1400x1050 60 65.3 121.8

UXGA 1600x1200 60 75.0 161.0 Standard Timing Identication

Full HD 1920x1080 60 67.5 148.5

WUXGA 1920x1200 60 74 154 Reduced Blanking

WXGA 1280x720 60 44.8 74.2 Standard Timing Identication

1280x800 60 49.6 83.5

1366x768 60 47.7 84.8

1440x900 60 59.9 106.5 Standard Timing Identication

WSXGA+ 1680x1050 60 65.3 146.3

1920x720 60 44.35 92.25

480i

720x480

(1440x480)

V.Frequency

[Hz]

(2) Extended Wide timing

(3) Component Signal

59.94(29.97) 15.7 13.5

H.Frequency

[KHz]

Pixel CLK

[MHz]

25,2

31.5

31.5

36.0

36.0

40.0

EDID Description

Established Timings 1

Established Timings 1

Established Timings 1

Established Timings 1

Established Timings 1

WXGA: Established Timings 2

XGA: Established Timings 2

and (Native)Detailed Timing / Descrip­tor Block 1

WXGA: (Native)Detailed Timing / De­scriptor Block 1
XGA: Standard Timing Identication

WXGA: Standard Timing Identication

XGA: N/A

English 45

APPENDICES

576i

480p 720x480 59.94 31.5 27.0

576p 720x576 50 31.3 27.0

720p 1280x720 60 45.0 74.25

720p 1280x720 50 37.5 74.25

1080i 1920x1080 60(30) 33.8 74.25

1080i 1920x1080 50(25) 28.1 74.25

1080p 1920x1080 23.98/24 27.0 74.25

1080p 1920x1080 60 67.5 148.5

1080p 1920x1080 50 56.3 148.5

Modes Resolution

VGA 640x480 60 31.5

IBM 720x400 70 31.5 28.3 Established Timings 1

SVGA 800x600 56 35.1

Apple, Mac II 832x624 75 49.1 57.3 Established Timings 2

XGA 1024x768 60 48.4 65.0

Apple, Mac II 1152x870 75 68.7 100.0 Manufacturer’s Reserved Timing

SXGA 1280x1024 60 64.0 108.0

QuadVGA 1280x960 60 60.0 101.3 Standard Timing Identication

SXGA+ 1400x1050 60 65.3 121.8

UXGA 1600x1200 60 75.0 161.0 Standard Timing Identication

Full HD 1920x1080 60 67.5 148.5

WUXGA 1920x1200 60 74 154 Reduced Blanking

720x576

(1440x576)

640x480 67 35.0 26.8 Established Timings 1

640x480 72 37.9

640x480 75 37.5

640x480 85 43.3

800x600 60 37.9

800x600 72 48.1 50.0 Established Timings 2

800x600 75 46.9 49.5 Established Timings 2

800x600 85 53.7 56.3

1024x768 70 56.5 75.0 Established Timings 2

1024x768 75 60.0 78.8 Established Timings 2

1024x768 85 68.7 94.5

1024x768 120 99.0 137.8 Standard Timing Identication

1280x1024 72 77.0 133.0

1280x1024 75 80.0 135.0 Established Timings 2

1280x960 75 75.2 130.0

50(25) 15.6 13.5

B. HDMI Digital

(1) PC Signal

V.Frequency

[Hz]

H.Frequency

[KHz]

(2) Extended Wide timing

Pixel CLK

[MHz]

25,2

31.5

31.5

36.0

36.0

40.0

EDID Description

Established Timings 1

Established Timings 1

Established Timings 1

Established Timings 1

Established Timings 1

WXGA: Established Timings 2

XGA: Established Timings 2

and (Native)Detailed Timing / Descrip­tor Block 1

46 English

APPENDICES

WXGA 1280x720 60 44.8 74.2 Standard Timing Identication

WXGA: (Native)Detailed Timing / De-

1280x800 60 49.6 83.5

1366x768 60 47.7 84.8

1440x900 60 59.9 106.5 Standard Timing Identication

WSXGA+ 1680x1050 60 65.3 146.3

1920x720 60 44.35 92.25

(3) HDMI - Video Signal

640x480p 640x480 59.94/60 31.5 25.2

480i

576i

480p 720x480 59.94 31.5 27.0

576p 720x576 50 31.3 27.0

720p 1280x720 60 45.0 74.25

720p 1280x720 50 37.5 74.25

1080i 1920x1080 60(30) 33.8 74.25

1080i 1920x1080 50(25) 28.1 74.25

1080p 1920x1080 23.98/24 27.0 74.25

1080p 1920x1080 60 67.5 148.5

1080p 1920x1080 50 56.3 148.5

Frame Packing

Top-and-Bottom

720x480

(1440x480)

720x576

(1440x576)

720p 50 75 148.5

720p 59.94/60 90 148.5

1080p 23.98/24 54 148.5

720p 50 37.5 74.25

720p 59.94/60 45.0 74.25

1080p 23.98/24 27.0 74.25

59.94(29.97) 15.7 13.5

50(25) 15.6 13.5

(4) HDMI 1.4a mandatory 3D timing- Video Signal

(5) Input signal frequency range

Analog: fh=15kHz～100kHz, fv=24Hz～120Hz, Max. pixel rate: 162.5MHz

Digital (HDMI): fh=15kHz～100kHz, fv=24Hz～120Hz, Max. pixel rate: 200MHz

scriptor Block 1
XGA: Standard Timing Identication

WXGA: Standard Timing Identication

XGA: N/A

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

(Native)Short Video Descriptor of CEA
EDID Timing

(Native)Short Video Descriptor of CEA
EDID Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

Short Video Descriptor of CEA EDID
Timing

English 47

APPENDICES

Ceiling Mount Installation

1. To prevent damage to your projector, please use the Optoma ceiling mount.

2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projec­tor meet the following specifications:

Screw type: M4*4

•

Minimum screw length: 14mm•

Note: Please note that damage resulting from incorrect installation will void the warranty.

Warning:

1. If you buy a ceiling mount from another company, please be sure to use the correct screw size. Screw size
will vary depending on the thickness of the mounting plate.

2. Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.

3. Avoid installing the projector near a heat source.

48 English

APPENDICES

Optoma global ofces

For service or support, please contact your local ofce.

USA

3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com [e-mail]

Canada

3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com [e-mail]

Latin America

3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com [e-mail]

Europe

42 Caxton Way, The Watford Business Park
Watford, Hertfordshire,
WD18 8QZ, UK [phone]
www.optoma.eu [phone]
Service Tel : [phone]

[e-mail]

Benelux BV

Randstad 22-123 [phone]
1316 BW Almere [phone]
The Netherlands
www.optoma.nl

France

Bâtiment E [phone]
81-83 avenue Edouard Vaillant
92100 Boulogne Billancourt,
France [e-mail]

[phone]

Spain

C/ José Hierro,36 Of. 1C [phone]
28522 Rivas VaciaMadrid, [phone]
Spain

Scandinavia

Lerpeveien 25 [phone]
3040 Drammen [phone]
Norway [e-mail]

PO.BOX 9515
3038 Drammen
Norway

Korea

WOOMI TECH.CO.,LTD.
4F,Minu Bldg.33-14, Kangnam-Ku,
seoul,135-815, KOREA +82+2+34430005

+82+2+34430004

Japan

東京都足立区綾瀬3-25-18
株式会社オーエス
コンタクトセンター:0120-380-495

[e-mail]

www.os-worldwide.com

Taiwan

12F., No. 213,Sec. 3, Beixin Rd.,
Xindian Dist., New Taipei City 231,
Taiwan, R.O.C.
www.optoma.com.tw asia.optoma.com

[phone]

[phone]

[e-mail]

Hong Kong

Unit A, 27/F Dragon Centre,
79 Wing Hong Street, [phone]
Cheung Sha Wan, [phone]
Kowloon, Hong Kong www.optoma.com.hk

China

5F, No. 1205, Kaixuan Rd., [phone]
Changning District [phone]
Shanghai, 200052, China www.optoma.com.cn

Deutschland

Wiesenstrasse 21 W [phone]
D40549 Düsseldorf, [phone]
Germany [e-mail]

www.optoma.com