OPTI-UPS AS450, AS450B, AS450C, AS650, AS650B Quick Manual

6hours

CAUTION: NEVER connect a laser printer or scanner to the

UPS unit. This may cause the damage of the unit.

1. Package Contents

You should have received the following items inside of package:

- UPS Unit

- Quick Guide

- Communication cable (only for the model with USB/RS-232 port)

- Power cable (only for the IEC-type model)

2. Product Overview

Front View:

Back View:

NEMA Type IEC Type Schuko Type Universal Type

3. Installation and Initial Startup

NOTE: Before installation, please inspect the unit. Be sure that nothing inside

the package is damaged.

Placement & Storage Conditions

Install the UPS in a protected area that is free of excessive dust and has adequate air flow.
Please place the UPS away from other units at least 20 cm to avoid interference. Do NOT
operate the UPS where the temperature and humidity is outside the specific limits. (Please
check the specs for the limitations.)

Connect to Utility and Charging

Plug in the AC input cord to the wall outlet. For the best results,
suggest to charge the battery at least 6 hours before initial use.
The unit charges its battery while connecting to the utility.

Connect the Loads

Plug in the loads to output receptacles on the rear panel of the UPS. Simply turn on the
power switch of UPS unit, then devices connected to the UPS will be protected by UPS unit.

Connect Modem/Phone/Network for Surge Protection

(Only for the model with

RJ-11/RJ-45)

Connect a single modem/phone line into surge-protected “IN” outlet on the back panel of
the UPS unit. Connect from “OUT” outlet to the computer with another phone line cable.

Connect Communication Cable

(Only for the model with USB/RS-232 port)

To allow for unattended UPS shutdown/start-up and status monitoring, connect the
communication cable one end to the USB/RS-232 port and the other to the communication
port of your PC. With the monitoring software installed, you can schedule UPS
shutdown/start-up and monitor UPS status through PC.

Turn On/Off the Unit

Turn on the UPS unit b y pressing the power switch. Turn off the UPS unit by pressing again
the power switch.

Active Line Interactive UPS Quick Guide V. 1.1

X

Output receptacles Y

AC input

Z Circuit breaker

[ RS-232 communication port

\ Modem

/p

hone or Network surge protection ] USB communicationport

X

Power Switch

Y

AC mode indicator: green lighting

Z Battery mode indicator: yellow

flashing

[

Fault mode indicator: red lighting

4. Important Safety Warning (SAVE THESE INSTRUCTIONS)

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity

controlled indoor area free of conductive contaminants. (See the specifications for the
acceptable temperature and humidity range.)
CAUTION! T o reduce the risk of o verheating the UPS, do not co ver the UPS' cooling vents and
avoid exposing the unit to direct sunlight or installing the unit near heat emitting appliances
such as space heaters or furnaces.
CAUTION! Do not attach non-computer-related items, such as medical equipment,
life-support equipment, microwave ovens, or vacuum cleaners to UPS.

CAUTION! Do not plug the UPS input into its own output.
CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages

or any other liquid-containing vessels on or near the unit.
CAUTION! In the event of an emergency, press the OFF button and disconnect the power
cord from the AC power supply to properly disable the UPS.

CAUTION! Do not attach a power strip or surge suppressor to the UPS.
CAUTION! If the UPS is with metal chassis, for safety purpose, grounding is a must during

UPS installation in order to reduce leakage current below 3.5A.
Attention hazardous through electric shock. Also with disconnection of this unit from the
mains, hazardous voltage still may be accessible through supply from battery. The battery
supply should be therefore disconnected in the plus and minus pole at the quick connectors of
the battery when maintenance or service work inside the UPS is necessary.
CAUTION! Servicing of batteries should be performed or supervised by personnel
knowledgeable of batteries and the required precautions. Keep unauthorized personnel away
from batteries.

CAUTION! When replacing the batteries, use the same number and type of batteries.
CAUTION! Internal battery voltage is 12VDC. Sealed, lead-acid, 6-cell battery.
CAUTION! Do not dispose of batteries in a fire. The battery may explode. Do not open or

mutilate the battery or batteries. Released electrolyte is harmful to the skin and eyes.

CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
CAUTION! A battery can present a risk of electric shock and high short circuit current. The

following precaution should be observed before replacing batteries:

1) Remove watches, rings, or other metal objects.

2) Use tools with insulated handles.

3) Wear rubber gloves and boots.

4) Do not lay tools or metal parts on top of batteries.

5) Disconnect charging source prior to connecting or disconnecting batteries terminal.

5. Software Download & Installation (Only for the model with
communication port)

Please follow steps below to download and install monitoring software:

1. Go to the website http://www.power-software-download.com

2. Click ViewPower software icon and then choose your required OS to download the software.

3. Follow the on-screen instructions to install the software.

4. When your computer restarts, the monitoring software will appear as an orange plug icon
located in the system tray, near the clock.

6. Trouble Shooting

Use the table below to solve minor problems.

Problem Possible Cause Solutions

Low battery. Charge the UPS at least 6 hours.
Battery fault. Replace the battery with the same

type of battery.

No LED display on the
front panel.

The UPS is not turned on. Press the power switch again to turn

on the UPS.
Alarm continuously
sounds when the
mains is normal.

The UPS is overload. Remove some loads first. Before

reconnecting equipment, please

verify that the load matches the UPS

capability specified in the specs.

The UPS is overload. Remove some critical load.
Battery voltage is too low. Charge the UPS at least 6 hours.

When power fails,
back-up time is shorten.

Battery defect. It might be
due to high temperature
operation environment, or
improper operation to battery.

Replace the battery with the same

type of battery.

The mains is normal but
yellow LED is flashing.

Power cord is loose. Reconnect the power cord properly.

7 Specifications

Model AS450/AS450B/

AS450C

AS650/AS650B/

AS650C

AS850/AS850B/

AS850C

CAPACITY 450 VA / 240 W 650 VA / 360 W 850 VA /480 W
INPUT

Voltage 110/120 VAC or 220/230/240 VAC
Voltage Range 81-145 VAC / 162-290 VAC
OUTPUT
Voltage Regulation +/-10%
Transfer Time Typical 4 ms
Waveform Simulated Sine Wave
BATTERY
Type & Number 12 V/4.5 AH x 1 12 V/7 AH x 1 12 V/9 AH x 1
Charging Time < 4 hours recover to 90% capacity
PHYSICAL
Dimension (DxWxH) 11.29 x 3.93 x 5.59 in / 287 x 100 x 142 mm
Net Weight 7.9 lbs / 3.6 kg 9.4 lbs / 4.3 kg 10.9 lbs / 4.9 kg
Environment
Humidity

0-90 % RH @ 0-40°C / 32~104°F (non-condensing)
Noise Level Less than 45 dB
MANAGEMENT
USB/RS-232 (Option) Windows 98 SE/ME/NT 4.x/2000/2003/XP/Vista/2008