Opticon OPR 3201 Specifications Manual
Gun-type Laser Barcode Scanner
OPR 3201
The OPR 3201 is a gun-Type laser barcode scanner
that uses a short-wavelength red laser beam to
enhance the visibility of scanning lines. The decoded
text of barcode images is output through an
RS-232C, USB, or Wedge interface.
Specifications Manual
All information subject to change without notice.
Document History
Opticon
OPR 3201
Specifications Manual
Model Number:
Edition:
Date:
OPR 3201
1A
2009-08-31
Specification Number:
Original Spec Number:
SS07067
SS07040
Copyright 2009 Opticon. All rights reserved.
This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or
machine readable form without prior written consent of Opticon.
Limited Warranty and Disclaimers
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE
PRODUCT.
Serial Number
A serial number appears on all Opticon products. This official registration number is directly related to the device
purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty.
Warranty
Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and
workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in
materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by
modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under
warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect,
consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon
has been informed about the possibility of such damages.
Packaging
The packing materials are recyclable. We recommend that you save all packing material to use should you need to
transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered by
the warranty.
Trademarks
Trademarks used are the property of their respective owners.
Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-17,
Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1184
SUPPORT
USA Europe
Phone: 800-636-0090
Email: support@opticonusa.com Email: support@opticon.com
Web: www.opticonusa.com Web: www.opticon.com
2
Opticon
OPR 3201
Specifications Manual
Contents
1. Abstract....................................................................................................................................... 7
2. Overview...................................................................................................................................... 7
3. Physical Features....................................................................................................................... 8
3.1. Dimensions ......................................................................................................................... 8
3.2. Weight ................................................................................................................................. 8
4. Environmental Specifications ...................................................................................................8
4.1. Operating Temperature and Humidity................................................................................. 8
4.2. Charging Temperature ........................................................................................................ 8
4.3. Storage Temperature and Humidity .................................................................................... 8
4.4. Ambient Light Immunity....................................................................................................... 8
5. Controls..................................................................................................................................... 10
6. Electrical Specifications .......................................................................................................... 10
6.1. Configuration..................................................................................................................... 10
6.2. Electrical Characteristics................................................................................................... 11
6.3. AC Adapter........................................................................................................................ 11
6.3.1. AC Input ...................................................................................................................................12
6.3.2. DC Output ................................................................................................................................12
7. Optical Specifications.............................................................................................................. 12
7.1. Laser Scan Specifications................................................................................................. 12
7.1.1. Tilt of Laser Scan Line .............................................................................................................13
7.1.2. Curvature of Scan ....................................................................................................................13
8. Technical Specifications.......................................................................................................... 14
8.1. Print Contrast Signal (PCS) .............................................................................................. 14
8.2. Minimum Resolution.......................................................................................................... 14
8.3. Scan Area and Resolution ................................................................................................ 15
8.3.1. Depth of Field...........................................................................................................................15
8.4. Pitch, Skew, and Tilt.......................................................................................................... 16
8.5. Curvature .......................................................................................................................... 17
9. Interface Specifications ...........................................................................................................18
9.1. RS-232C Interface Spec ................................................................................................... 18
9.1.1. Settings and Communication ...................................................................................................18
9.1.2. Signal Level..............................................................................................................................18
3
Opticon
OPR 3201
Specifications Manual
Interface Circuit ........................................................................................................................19
9.1.3.
9.1.4. Character Format .....................................................................................................................19
9.1.5. Communication Format............................................................................................................19
9.1.6. Handshaking ............................................................................................................................20
9.2. USB-HID and USB-VCP Interface Specifications ............................................................. 25
9.2.1. Settings ....................................................................................................................................25
9.2.2. Interface Circuit ........................................................................................................................25
9.3. Wedge Interface Specification .......................................................................................... 25
9.3.1. Settings ....................................................................................................................................25
10. Cable and Connector ............................................................................................................... 26
10.1. RS-232C Cable ................................................................................................................. 26
10.1.1. Connector.................................................................................................................................26
10.1.2. Pin Assignment ........................................................................................................................26
10.2. USB Cable ........................................................................................................................ 27
10.2.1. Connector.................................................................................................................................27
10.3. Wedge Cable .................................................................................................................... 28
10.3.1. Connector.................................................................................................................................28
11. Default Settings........................................................................................................................ 29
11.1. Set Default Interface ......................................................................................................... 29
11.2. Default Settings 1: Readable Codes ................................................................................. 31
11.3. Default Settings 2: Read Options, Trigger, Buzzer ........................................................... 32
11.4. Default Settings 3: Communication Settings ..................................................................... 33
11.4.1. Default Settings 3A: Serial Communication Settings— RS-232C ...........................................33
11.4.2. Keyboard Communication Settings—USB ..............................................................................33
11.4.3. Keyboard Communication Settings—Wedge ..........................................................................33
12. Serial Number and Labeling.................................................................................................... 34
13. Packaging Specifications........................................................................................................35
13.1. Individual Packaging Specification .................................................................................... 35
13.2. Collective Packaging Specification ................................................................................... 36
14. Durability................................................................................................................................... 37
14.1. Static Electricity ................................................................................................................. 37
14.2. Shock ................................................................................................................................ 37
14.2.1. Drop Test (without packaging).................................................................................................37
14.2.2. Drop Test (with individual packaging)......................................................................................37
4
Opticon
OPR 3201
Specifications Manual
14.3. Vibration Strength (without packaging) ............................................................................. 38
14.4. Vibration Strength (with individual packaging) .................................................................. 38
14.5. Dust and Drip Proof........................................................................................................... 38
14.6. Cable Strength ..................................................................................................................38
14.7. Cable Bending Test........................................................................................................... 39
15. Reliability................................................................................................................................... 39
16. Trigger and Read Options ....................................................................................................... 40
16.1. Auto Trigger Overview ...................................................................................................... 40
16.2. Stand Detection.................................................................................................................41
16.3. Auto Trigger Settings ........................................................................................................ 41
16.3.1. Enable when Scanner Inserted in Stand .................................................................................41
16.3.2. Enable Auto Trigger All the Time.............................................................................................42
16.3.3. Only Trigger Manually..............................................................................................................42
17. Regulatory Compliance ...........................................................................................................43
17.1. Laser Safety ...................................................................................................................... 43
17.2. Product Safety................................................................................................................... 43
17.3. EMC .................................................................................................................................. 43
17.4. RoHS................................................................................................................................. 43
18. Safety......................................................................................................................................... 44
18.1. Shock ................................................................................................................................ 44
18.2. Temperature Conditions.................................................................................................... 44
18.3. Foreign Materials .............................................................................................................. 44
18.4. Other ................................................................................................................................. 44
19. Mechanical Drawing.................................................................................................................45
Table of Figures
Figure 1: Ambient light immunity.............................................................................................. 9
Figure 2: OPR 3201 configuration .............................................................................................. 10
Figure 3: AC adapter 1 ............................................................................................................... 12
Figure 4: AC adapter 2 ............................................................................................................... 12
Figure 5: Laser scan tilt and curvature ....................................................................................... 13
Figure 6: Depth of field ............................................................................................................... 15
Figure 7: Pitch ............................................................................................................................ 16
Figure 8: Curvature..................................................................................................................... 17
Figure 9: Interface circuit ............................................................................................................ 19
Figure 10:Character format (same for both sending and receiving) ........................................... 19
5
Opticon
OPR 3201
Specifications Manual
Figure 11: Communication format............................................................................................... 19
Figure 12: No handshaking ........................................................................................................ 20
Figure 13: Busy/Ready communication...................................................................................... 20
Figure 14: Cannot receive command ......................................................................................... 21
Figure 15: Signal timing.............................................................................................................. 21
Figure 16: Modem transmit data................................................................................................. 22
Figure 17: ACK/NAK................................................................................................................... 23
Figure 18: ACK/NAK—No response........................................................................................... 24
Figure 19: Interface circuit .......................................................................................................... 25
Figure 20: RS-232C cable .......................................................................................................... 26
Figure 21: USB cable ................................................................................................................. 27
Figure 22: USB “A” connector ....................................................................................................27
Figure 23: Wedge cable.............................................................................................................. 28
Figure 24: Host connector .......................................................................................................... 28
Figure 25: Keyboard connector .................................................................................................. 29
Figure 26: Serial number label ................................................................................................... 34
Figure 27: FCC compliance label ............................................................................................... 34
Figure 28: CE compliance label..................................................................................................34
Figure 29: Individual packaging.................................................................................................. 35
Figure 30: Collective packaging.................................................................................................. 36
Figure 31: Drop test.................................................................................................................... 37
Figure 32: Cable bending test .................................................................................................... 39
Figure 33: Auto trigger operation................................................................................................ 40
Figure 34: Auto trigger configuration diagram ............................................................................ 41
Figure 35: Mechanical drawing...................................................................................................45
6
Specifications Manual
1. Abstract
This manual provides specifications for the OPR 3201 Gun-type Laser Barcode Scanner.
2. Overview
The use of a short-wavelength red laser beam enhances the visibility of scanning lines.
The decoded text of barcode images is output through an RS-232C, USB, or Wedge interface,
depending on the specification.
The OPR 3201 offers auto trigger options.
This product complies with RoHS.
Supported symbologies:
Linear (1D) Postal 2D
Opticon
OPR 3201
JAN/UPC/EAN, incl. add-on Chinese Post Composite Codes
Codabar/NW-7 Korean Postal Authority Code MicroPDF417
Code 11 PDF417
Code 39
Code 93
Code 128
GS1-128 (EAN-128)
GS1 Databar (RSS)
IATA
Industrial 2of5
Interleaved 2of5
ISBN-ISMN-ISSN
Matrix 2of5
MSI/Plessey
S-Code
Telepen
Tri-Optic
UK/Plessey
7
3. Physical Features
3.1. Dimensions
W 56.0 x D 108.1 x H 148.6 mm
3.2. Weight
78.0 g ±5 g (max.), excluding the cable
4. Environmental Specifications
4.1. Operating Temperature and Humidity
Temperature: -5 to 50° C
Humidity: 5 to 95%
4.2. Charging Temperature
Temperature: 0 to 40° C
Opticon
OPR 3201
Specifications Manual
4.3. Storage Temperature and Humidity
Temperature: -20 to 60° C
Humidity: 5 to 95%
4.4. Ambient Light Immunity
Decoding performance is guaranteed when the range of illumination on a barcode
surface is between zero and the following values:
Incandescent light 3,000 lx
Fluorescent light 3,000 lx
Sunlight 50,000 lx
8
Figure 1: Ambient light immunity
Opticon
OPR 3201
Specifications Manual
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
PCS: 0.9
Resolution: 0.25 mm
Symbology: 9-digit Code 39
Quiet zone: 10 mm
N/W ratio: 1:2.5
Distance: 70 mm
Angle (see note below): Α = 0° β = 15° γ = 0°
Curvature: R = ∞
Power supply voltage: 6.0 V (RS-232C)
5.0 V (Wedge/USB)
Direct light or specular reflection from a light source should be prevented from entering
the acceptance area.
Note: α, β and γ respectively represent pitch, skew and tilt. Please see section 8 for how
these values are defined.
9
5. Controls
Item Specifications
ASIC ARM7TDMI
SDRAM 64 KB
Flash ROM 8 MBits (512 K × 16 bits)
6. Electrical Specifications
6.1. Configuration
The OPR 3201 consists of a laser module (which includes a scan mirror, a coil, and a
photo diode), a decode and communication section (which decodes scanned data and
carries out signal processing), a 3.3 V power supply, an interface (which outputs decoded
data), a buzzer, LEDs, and a trigger key.
The OPR 3201 RS-232C model operates on a DC 6.0 V power supply fed from the
dedicated adapter. USB and Wedge models operate on bus power, so those models do
not use an adapter.
Opticon
OPR 3201
Specifications Manual
Figure 2: OPR 3201 configuration
10
6.2. Electrical Characteristics
Interface Parameter Min Typ Max Unit Notes
Opticon
OPR 3201
Specifications Manual
RS-232C
USB
Wedge
Operating voltage 4.5 6.0 6.6 V
Operating current — 100 160 mA 100 mA—Laser: ON, Buzzer: OFF
160 mA—Laser: ON, Buzzer /LED:ON
Rush current — 550 600 mA Power supply voltage: 6.0 V
Stand-by current — 35 65 mA Auto trigger OFF/ON
Operating voltage 4.5 5.0 5.5 V
Operating current — 100 160 mA 100 mA—Laser: ON, Buzzer: OFF
160 mA—Laser: ON, Buzzer /LED:ON
Rush current — 450 500 mA Power supply voltage: 5.0 V
Stand-by current — 35 65 mA Auto trigger OFF/ON
Conditions
Connect 1Ω resistance to a power supply line in series and measure the current by the
voltage between both ends of resistance.
Power supply voltage is measured at a connector terminal area.
The current value depends on the interface type and host computer to which the device is
connected.
6.3. AC Adapter
The OPR 3201 with RS-232C serial interface is shipped with a dedicated AC adapter
“Universal AC Adapter Kit.” Plug connectors can be changed for each region. See
diagrams below.
Item Specification
Model Name SFP0602000P-PSE
Dimensions 47.5 (W) × 28.0 (D) × 75.0 (H) mm
DC output cable length 1.8m
Voltage range AC 90 to 265 V
Input specifications
Output Specifications
Operating temperature 0 to 40°
Supply current 0.5 A max
Voltage range 5.7 to 6.3 V
Maximum current 2 A max
11
6.3.1. AC Input
Dimensions: 47.5 (W) × 28.0 (D) × 75.0 (H) mm (except protruding portion)
Opticon
OPR 3201
Specifications Manual
Figure 3: AC adapter 1
6.3.2. DC Output
7. Optical Specifications
7.1. Laser Scan Specifications
Parameter Specification Unit
Light-emitting element Red laser diode —
Emission wavelength 650 ±10 (25° C) nm
Light output 1.0 or less mW
Scanning method Bi-directional scanning —
Scanning speed 100 ±20 scans/s
Notes:
Figure 4: AC adapter 2
Scan angle: 54 ±5 ° Scan angle
Read angle: 44 (Min) °
Refer to chapter 16, “Trigger and Read Options,” to read about the scan modes.
12
Opticon
OPR 3201
Specifications Manual
Refer to chapter 8, “Technical Specifications,” to read about scanning performance.
7.1.1.
7.1.2.
Tilt of Laser Scan Line
Laser scanning tilt is the vertical difference between both ends of a laser scan
line. Measure it in the middle of the laser scan line.
• Up to 0.92° angle in vertical direction from the scan origin (mirror motor).
• Up to 2.46 mm when measured at a point 150 mm from the scan origin.
Curvature of Scan
The maximum difference between the laser scan line and the line between both
ends of the laser scan line. Measure it in the middle of the laser scan line.
• Up to 1.27° angle in vertical direction from the scan origin (mirror motor).
• Up to 3.3 mm curvature when measured at a point 150 mm away from the
scan origin.
Figure 5: Laser scan tilt and curvature
13
Specifications Manual
8. Technical Specifications
The conditions for technical specifications are as follows, unless otherwise specified in each
section.
Conditions
Opticon
OPR 3201
Ambient temperature
and humidity:
Ambient light: 500 to 900 lx
Background: Barcode = black
Power supply voltage: 6.0 V (RS-232C)
Decoding test: Approve the performance when decoding is successful in all ten tests.
Room temperature (5 to 35º C)
Room humidity (45% to 85% RH)
Space = white
Margin = white
Background of label = black
5.0 V (USB and Wedge)
(Decoding is deemed successful when completed in 0.5 seconds or less.)
8.1. Print Contrast Signal (PCS)
0.45 or higher (over 70% of reflectivity of space and quiet zone).
Reflectance of white bar－Reflectance of black bar
PCS=
Reflectance of white bar
Scanning performance may decline if dirt or scratches mar the optical window. Keep the
optical window clean.
8.2. Minimum Resolution
0.127 mm
14
Loading...