Opticon OPL 9713 User Manual

OPL-9713

①②③

⑤

⑦⑧

⑥

④

Quick Start Guide

Introduction

• Read this quick start guide carefully before installing and/or using this product.

• Keep this quick start guide for future reference and store in a safe place.

• The OPL-9713 is a laser data collector with a GPS feature. The GPS feature makes it possible to add
location data and a time stamp to scanned barcode data.

Notice

• This quick start guide may b e revised or withdrawn at any time without prior notice.

• This quick start guide may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any
electronic or machine readable form without prior writ ten consent of Opticon.

• Trademark s used are property of their respective owners.

• Under no circumstances shall Opticon be held responsible for any special, incidental, consequential or indirect dam­ages, howsoever caused.

Caution and Warning

1. Laser Sa fety

• Do not stare into the laser beam.

2. Handling Instructions

【OPL-9713

• Do not attempt to disassemble, modify or update this device.

• Operating the scanner while operating machinery or a vehicle can be distracting.

• Do not drop this product or put heavy items on this product.

• Do not insert foreign substances into the dev ice.

• Do not use this product in the following areas:

- In areas exposed to direct sunlig ht for long periods of time.

- In dusty environments.

- Near water or other liquids, or in extremely high humidity.

- Near heat sources, such as radiators, heat registers, s toves, or other types of devices that produce heat.

- Near microwaves, medical devices, or low-power radio stations.

• When cleaning this produ ct, rub gently with either a soft dry cloth or a damp cloth with mild detergent.

【Battery

• Do not attempt to disassemble the battery.

• Do not expose the battery to heat sources including other devices that produce heat.

• Do not short the power leads on the battery. If the (+) and (-) terminals come in contact with metals (such as a necklace or
hairpin), a short-circuit will occur.

• Do not load the battery with the (+) and (-) terminals reversed.

• If you come into contact with material from a leaking battery, take the following actions:

- If the material gets into the eyes, do not rub. Immediately flush the eyes with clean water and seek medical attention.

- If the material comes into contact with the skin or clothes, immediately rinse the affected area with clean water. Consult

• Check local regulations for proper battery disposal.

】

】

your physician if inflammation or soreness develops.

( Please refer to the specification manual and instruction guide for details.)

Before Getting Started

■

What's in the Box

Confirm that you have the following items before getting started:

No. Item Function

1 Data Collector A lase r barcode collector with a barcode scanning fea ture.

2 Lithium-ion Battery Pack Desi gnated batt ery pa ck for the OPL-97 13.

3 Strap

4 Quick Start Guid e Provid es product information and instruction guide.

* T he num ber of acce ssorie s may diffe r depe nding on the prod uct sp ecific ation .
Please conta ct th e near est de aler if acc essori es are dama ged or missi ng.

Copyright© 2007, Opticon All ri ghts reserved.

Overview

■

OPL-9713 Basic Specifications

Parame ter Specif ications

Physical
Features

Control
Section

External
Memory

Display
Section

Operation Section
Scanning

Section

Power Supply
Section

Clock Section
Comm.

Section

Durability

Size (H) 129
Weight 110g M ax (excludin g batteries )
Color Light gray
CPU 16-bit CP U
Clock Frequency

FLASH ROM

SRAM 512kB (for WORK an d DATA)
LED Tri-color LED (Blue, Red and Green)
Buzzer Loudne ss : 75dBA o r higher
Keys 1 Key
Light Source Red laser diode
Wavelength / Output
Scan Rate 100 scans / sec
Supported

Symbologies
Main Battery
Backup Battery
Operating Time
Data Retention Time
Real Time Clock (RTC)

IrDA

GPS

Operating Temp.
Operating Humidity
Storage Temp.
Storage Humidity
Charging Temp.
Dust- and Drip-proof

Shock

×

(W) 44 × (D) 26 mm Max

14.74M Hz
512 KB for BIOS and AP

(2MB flash memory is optionally available)

650 ±10nm / 1mW or less

JAN/U PC/EAN (WPC), Codabar /NW-7, Code 39,
Code 93, Code 128, Industrial 2of5, In terleaved 2of5

Lithium-ion secondary ba ttery（600mA

Lithium-ion secondary ba ttery（3.4mA )

50 hours or longer

7 hours or longer (with GPS operations)

Supports year, month, day, hour, minute. (Leap year supported.)

Specification : IrDA Ver1.2 Low Power

Baud rate : 2400bps to 115.2 kbps

GPS Module : SIRF GSC3 Chip

Reception Frequency : 1575.42 MHz

Channels : 20 Max

Antenna : Patch antenna (20mm x 20mm)

0 deg. C to 40 deg . C

20% to 85% (non-co ndensing)

-20 de g. C to 60 d eg. C

20% to 90% (non-condensing)

0 deg. C to 40 deg. C

IP54
Dropped 3 times onto concrete from a

height of 150 cm with no defects found.

Designated Cradle

Communication &
Charging Cradle

CRD-9723

RS-232C

* To conne ct the cr adle to a hos t using a de dicated U SB cable, yo u must fi rst insta ll a dedic ated USB dri ver on the h ost.
* Plea se refer to the speci ficatio n manual or t he instru ction gui de for det ails of des ignated cr adles.

Communication Method
(Cradle to Host)

Size

Weig ht

Charging Time 3.5 hours

USB

Communicates with the host
via RS-232C or USB interface.

(H) 67.5 × (W) 71.5 × (D) 98.5 mm Max

85g Max (excluding AC adapter and cable)

■

Detailed View

No. Part Function

Scan Key Starts a barcode scanning operation.

①

GPS Antenna

②

）

Status LED

③

(Blue, Red and Green)

Optical Window

④

Charging Terminals

⑤

Battery Cover

⑥

Buzzer Hole

⑦

Strap Hook

⑧

TTFF (Time To First Fix)

Memo

TTFF is the time required for a GPS receiver to acquire satellite
signals and navigation data, and calculate a position solution.

The TTFF for the OPL-9713 is as follows:

Hot Start

Warm Start

Cold Start

(Optional)

Line-up of CRD-9723 series:

- single-bay cradle (1 x charging, 1 x communication)

- multi-bay cradle (5 x charging, 1 x communication)

- multi-bay cradle (5 x charging, 5 x communication)

Charging Cradle CRD-9722:

- single-bay cradle (1 x charging, no communication)

Receives information from a GPS satellite
and calculates a positio n solution.

Alerts users to the status of the scanning
operation and data communication.

The scan engine emits a laser beam through the
optical window while scanning a barcode.

Electrical terminals for power distribution
and power management.

Protects the battery pac k.

1 sec.

38 se c.

42 sec.

Contact

Please contact OPTICON or your local dealer.

The Netherlands

U.S.A.

France

Germany

Italy

Spain

More product details, additional support, and configuration options (from the Universal Menu Book) are available at www.opticon.com.

Opticon Sensors Europe B.V.

tel: [phone]

Opticon Inc.

tel: [phone]

Opticon S.A.S.

tel: [phone]

Opticon Sensoren GmbH

tel: [phone]

Opticon s.r.l.

tel: [phone]

Opticon Sensores S.L.

tel: [phone]

email: [e-mail]

/

email: [e-mail]

/

email: [e-mail]

/

email: [e-mail]

/

email: [e-mail]

/

email: [e-mail]

/

Sweden

United Kingdom

Taiwan

China

Australia

Brazil

Opticon Sensors Nordic AB

tel: [phone]

Opticon Limited

tel: [phone]

Opticon Far Eastern Ltd.

tel: [phone] / email: [e-mail]

Opticon Sensors Europe B.V., Shanghai Representative Oce

tel: [phone]

Opticon Sensors Pty. Ltd.

tel: [phone]

Opticon Sensors Europe B.V., Latin American Oce

tel: [phone]

email: [e-mail]

/

email: [e-mail]

/

email: [e-mail]

/

email: [e-mail]

/

email: [e-mail]

/

OPL97139062- 0-00