Opticon H19 User Manual

CAUTION: This information is subject to change without prior notice.

Warranty

Unless otherwise agreed in a written contract, all Opticon products are warranted against defects
in materials and workmanship for two years after purchase. Opticon will repair or, at its option,
replace products that are defective in materials or workmanship with proper use during the
warranty period. Opticon is not liable for damages caused by modifications made by a customer.
In such cases, standard repair charges will apply. If a product is returned under warranty and
no defect is found, standard repair charges will apply. Opticon assumes no liability for any
direct, indirect, consequential or incidental damages arising out of use or inability to use both
the hardware and software, even if Opticon has been informed about the possibility of such
damages.

Packaging

The packing materials are recyclable. We recommend that you save all packing material to use if
you need to transport your cradle or send it for service. Damage caused by improper packaging
during shipment is not covered by the warranty.

WEEE Notice

The WEEE logo ( ) on the product and its accessories or on its box indicates that this
product must not be disposed of or dumped with your other household wastes. You are liable

to dispose of all your electronic or electrical waste equipment by relocating over to the specified
collection point for recycling of such hazardous waste. Isolated collection and proper recovery
of your electronic and electrical waste equipment at the time of disposal will allow us to help
conserving natural resources. Moreover, proper recycling of the electronic and electrical waste
equipment will ensure safety of human health and environment.

RoHS Compliance

This product is in compliance with Directive 2002/95/EC of the European Parliament and of
the Council of 27 January 2003, on the restriction of the use of certain hazardous substances in
electrical and electronic equipment (RoHS) and its amendment.

CRD

European Union Notice

Product with CE marking ( ) comply with the R&TTE Directive (99/5/EC), the EMC Directive
(89/336/EEC), and the Low Voltage Directive (73/23/EEC) issued by the Commission of the

European Community.

Regulatory Agency ID

For regulatory identification purposes your product is assigned a model number CRD -19. This
product is intended for use with certified Class B Limited Power Source, rated 5VDC, maximum

3.6A power supply unit.

IMPORTANT SAFETY INFORMATION

Please read the following information carefully before you start using this Opticon
device to avoid any damages caused by improper usage:

• This cradle is designed for use with the Opticon H-19 Pocket PC phone. Do not charge other
products using this cradle.

• Do not use accessories which have not been specified by the manufacturer.

• Do not use it if the provided plug does not fit into your outlet.

• Do not connect the AC adapter to an electric transformer.

• Unplug the cradle during lightning storms or when unused for long period of time.

• When discarding the batteries, dispose of them in a proper manner, according to the battery
manufacturer’s instructions and your local laws.

• Do not cover the cradle and the AC adapter or USB connector with a cloth or bedding
materials during use.

• Do not open the device housing or tamper with the device.

• Do not expose the cradle to direct sunlight, oily smoke, stream, excessive moisture or dust.

• Unplug the AC adapter and USB connector before cleaning.

• Gently wipe the product using a dry, soft cloth.

• Do not touch the connection pins shortly after charging is completed.

• Do not allow any metal object to contact with the connection pins and the AC adapter to avoid
a short-circuit.

• Do not touch the plug, AC adapter or cradle with wet hands.

• When the cradle emits unusual noise, smoke or amount of heat, immediately unplug the AC
adapter or USB connector and contact the original retailer.

-

CRD

-

Views of the Device Accessories

Please check the accessories included in the package:

Second battery slot

Removable plastic plate

Connection pins

PDA holder

USB port

Power indicator

Se c o n d battery st atus
indicator

Power jack

UK plug EU plug AU plug

USB indicator

Charging Your Pocket PC Phone

This cradle allows you to recharge your Pocket PC phone (PPC phone) and a second
battery (if have) with the AC adapter, as well as using ActiveSync to synchronize date
between your PPC phone and your PC.

You can charge your PPC phone and the second battery separately or together. You
can also charge your PPC phone and synchronize it with your PC at the same time.

To charge your PPC phone, do the following:

CRD

-

AC adapter USB cable

CRD

-

1. Plug the AC adapter into the power jack on the back of the cradle.

2. Plug the other end of the AC adapter into an electrical outlet.

3. Dock your PPC phone into the PDA holder of the cradle. Make sure that their
connection pins come into contact with each other.

Charging the Battery

You can fast-charge the battery with the cradle.

1. Plug the AC adapter into the power jack on the back of the cradle.

2. Plug the other end of the AC adapter into an electrical outlet.

3. Insert the battery into the second battery slot of the cradle. Make sure that
the battery is oriented correctly. (If you are charging a high capacity battery,
remove the removable plastic plate).

Synchronizing with Your PC

You hav e to instal l Ac tiv eSyn c on your P C be fore you can beg in
synchronizing.

1. Dock your PPC phone on the PDA holder of the cradle. Make sure that their
connection pins come into contact with each other.

2. Plug the USB cable into the USB port of the cradle.

3. Plug the other end of the USB cable into an available USB port on your PC.

4. The USB indicator on the cradle lights in green if there is an electrical current
flowing through the cradle successfully. You can then start charging or/and
synchronizing your PPC phone.

5. When the synchronization process completes, remove your PPC phone from
the cradle.

To charge and synchronize your PPC phone at the same time, connect the
AC adapter to the cradle first, and then connect the USB cable.

4. The power indicator on the cradle lights in green if there is an electric current
flowing through the cradle successfully.

5. The power LED on your PPC phone lights in orange during charging.

6. When charging is completed, pull your PPC phone up to detach it from the
cradle.

6061B0248601

CRD

4. The second battery status indicator displays the charging status. Remove the
battery when charging is completed.

Charging Fully charged No battery Error

Solid red light Solid green light Off Blinking red light

You can not charge the battery in the second battery slot with the USB
cable, use the AC adapter only.

Specification

Overall dimension 76.1mm×88.5mm×89.3mm (W/H/L)

Weight 116±2 g
AC adapter 5V 3.6A
Operating temperature 5˚C~40˚C
Operating humidity 20%~80%RH
Storage temperature -20˚C~60˚C
Storage humidity 20%~90%RH

Battery Charging Time

Charge with Full-charge time

PDA holder Standard battery: 4 hours

High capacity battery: 8 hours

Second battery slot Standard battery: 2.5 hours

High capacity battery: 5 hours

-

CRD

-

CRD

-