Opel Combo 2014 User Manual

OPEL COMBO

Owner's Manual

Contents

Introduction .................................... 2

In brief ............................................ 6

Keys, doors and windows ............ 20

Seats, restraints ........................... 33

Storage ........................................ 54

Instruments and controls ............. 62

Lighting ........................................ 88

Climate control ............................. 95

Driving and operating ................. 101

Vehicle care ............................... 125

Service and maintenance .......... 158

Technical data ........................... 161

Customer information ................ 177

Index .......................................... 180

2 Introduction

Introduction

Introduction 3

Vehicle specific data

Please enter your vehicle's data on
the previous page to keep it easily
accessible. This information is
available in the sections "Service and
maintenance" and "Technical data"
as well as on the identification plate.

Introduction

Your vehicle is a designed
combination of advanced technology,
safety, environmental friendliness
and economy.

This Owner's Manual provides you
with all the necessary information to
enable you to drive your vehicle
safely and efficiently.

Make sure your passengers are
aware of the possible risk of accident
and injury which may result from
improper use of the vehicle.

You must always comply with the
specific laws and regulations of the
country that you are in. These laws
may differ from the information in this
Owner's Manual.

When this Owner's Manual refers to a
workshop visit, we recommend your
Opel Service Partner.

All Opel Service Partners provide
first-class service at reasonable
prices. Experienced mechanics
trained by Opel work according to
specific Opel instructions.

The customer literature pack should
always be kept ready to hand in the
vehicle.

Using this manual

■ This manual describes all options
and features available for this
model. Certain descriptions,
including those for display and
menu functions, may not apply to
your vehicle due to model variant,
country specifications, special
equipment or accessories.

■ The "In brief" section will give you
an initial overview.

■ The table of contents at the
beginning of this manual and within
each section shows where the
information is located.

■ The index will enable you to search
for specific information.

■ This Owner's Manual depicts left­hand drive vehicles. Operation is
similar for right-hand drive vehicles.

■ The Owner's Manual uses the
factory engine designations. The
corresponding sales designations
can be found in the section
"Technical data".

■ Directional data, e.g. left or right, or
front or back, always relate to the
direction of travel.

■ The vehicle display screens may
not support your specific language.

■ Display messages and interior
labelling are written in bold letters.

Danger, Warnings and
Cautions

9 Danger

Text marked 9 Danger provides
information on risk of fatal injury.
Disregarding this information may
endanger life.

4 Introduction

9 Warning

Text marked 9 Warning provides
information on risk of accident or
injury. Disregarding this
information may lead to injury.

Caution

Text marked Caution provides
information on possible damage to
the vehicle. Disregarding this
information may lead to vehicle
damage.

Symbols

Page references are indicated with 3.
3 means "see page".

We wish you many hours of
pleasurable driving.

Adam Opel AG

Introduction 5

6 In brief

In brief

Initial drive information

Vehicle unlocking

Unlocking with key

Turn the key in the driver's door lock
towards the front of the vehicle.

Unlocking with radio remote control

Press button Ä to unlock the
vehicle.

Press button Å to unlock the load
compartment only.

Open the doors by pulling the
handles. To open the tailgate, press
the button under the tailgate handle.

Radio remote control 3 20, Central
locking system 3 21, Load
compartment 3 25, Power windows
3 29.

In brief 7

Seat adjustment

Seat positioning

Pull handle, slide seat, release
handle.

Seat position 3 34, Seat adjustment
3 34.

9 Danger

Do not sit nearer than 25 cm from
the steering wheel, to permit safe
airbag deployment.

Seat backrests

Turn handwheel. Do not lean on
backrest when adjusting.

Seat position 3 34, Seat adjustment
3 34.

Seat height

Lever pumping motion
up = higher

down = lower

Operate lever and adjust body weight
on seat to raise or lower it.

Seat position 3 34, Seat adjustment
3 34.

8 In brief

Head restraint adjustment

Press release catch, adjust height,
engage.

Head restraints 3 33.

Seat belt

Pull out the seat belt and engage in
belt buckle. The seat belt must not be
twisted and must fit close against the
body. The backrest must not be tilted
back too far (maximum approx. 25 °).

To release belt, press red button on
belt buckle.

Seat position 3 34, Seat belts
3 39, Airbag system 3 42.

Mirror adjustment

Interior mirror

Adjust the lever on the underside to
reduce dazzle.

Interior mirror 3 29.

In brief 9

Exterior mirrors

Swivel lever in required direction.

Select the relevant exterior mirror by
turning the control to left _ or right 6.
Then swivel the control to adjust the
mirror.

In position o no mirror is selected.
Convex exterior mirrors 3 28,

Electric adjustment 3 28, Folding
exterior mirrors 3 28, Heated
exterior mirrors 3 29.

Steering wheel adjustment

Unlock the lever, adjust the steering
wheel, then engage lever and ensure
it is fully locked.

Do not adjust steering wheel unless
vehicle is stationary and the steering
wheel lock has been released.

Airbag system 3 42, Ignition
positions 3 102.

10 In brief

Instrument panel overview

In brief 11

1 Fixed air vents ..................... 100

2 Side air vents ........................ 99

3 Light switch .......................... 88

Turn and lane-change
signals, headlight flash,

low beam and high beam ..... 90

4 Instruments .......................... 68

Driver Information Centre ...... 79

5 Windscreen wiper,

windscreen washer
system, rear window

wiper/washer ........................ 63

Trip odometer reset ............... 68

6 Centre air vents .................... 99

7 Headlight range

adjustment ........................... 89

Driver Information Centre

controls ................................ 79

Trip computer ........................ 86

Instrument illumination .......... 91

Hazard warning flashers .......90

Front fog lights ..................... 90

Rear fog light ........................ 91

Heated rear window .............. 32

Heated exterior mirrors ......... 29

8 Front passenger airbag ........ 45

9 Glovebox .............................. 55

10 Climate control system .......... 95

Electronic climate control

system ................................... 97

11 Selector lever, manual

transmission ....................... 107

Manual transmission

automated ........................... 108

12 Ignition switch with

steering wheel lock ............ 102

13 Steering wheel controls .......62

14 Horn ..................................... 63

Driver airbag ........................ 45

15 Steering wheel adjustment ..62

16 Cruise control ..................... 115

17 Fuse box ............................. 140

18 Bonnet release lever .......... 127

12 In brief

In brief 13

Exterior lighting

Turn light switch:

= off / daytime running lights

§

= sidelights / headlights

9

Lighting 3 88, Daytime running
lights 3 89.

Fog lights

Press light switch:

= front fog lights

>

= rear fog light

r

Headlight flash, high beam and low beam

headlight flash = pull lever
high beam = push lever
low beam = pull lever

High beam 3 88, Headlight flash
3 88.

14 In brief

Turn and lane-change signals

lever up = right turn signal
lever down = left turn signal

Turn and lane-change signals
3 90.

Hazard warning flashers

Operated with the ¨ button.
Hazard warning flashers 3 90.

Horn

Press j.

In brief 15

Washer and wiper systems

Windscreen wiper

Twist lever:

= off

§

Ç

= intermittent wiping

È

= slow

É

= fast

For a single wipe when the
windscreen wiper is off, move the
lever up.

Windscreen wiper 3 63, Wiper
blade replacement 3 131.

Windscreen and headlight washer systems

Pull lever.
Windscreen and headlight washer

system 3 63, Washer fluid 3 129.

Rear window wiper and washer systems

Twist band to activate the rear
window wiper.

The rear window wiper comes on
automatically when the windscreen
wiper is switched on and reverse gear
is engaged.

Push lever: Washer fluid is sprayed
on the rear window and the wiper
wipes a few times.

Rear window wiper/washer 3 64.

16 In brief

Climate control

Heated rear window, heated exterior mirrors

The heating is operated by pressing
the Ü button.

Heated rear window 3 32.

Demisting and defrosting the windows

Air conditioning system

Set the temperature control to
warmest level.

Set fan speed to highest level.
Set air distribution control to V.
Cooling n on.
Heated rear window Ü on.

Electronic climate control system

Press button Ê.
Temperature and air distribution are

set automatically and the fan runs at
a high speed.

To return to automatic mode: press
button n or AUTO.

Climate control system 3 95,
Electronic climate control system
3 97.

In brief 17

Transmission

Manual transmission

Reverse: with the vehicle stationary,
wait 3 seconds after depressing the
clutch pedal, pull up the collar on the
selector lever and engage the gear.

If the gear does not engage, set the
lever to neutral, release the clutch
pedal and depress again; then repeat
gear selection.

Manual transmission 3 107.

Manual transmission automated

N = neutral position

= drive position

o

+ = higher gear

- = lower gear
A/M = switch between automatic

and manual mode

R = reverse gear (with selector

lever lock)

Manual transmission automated
3 108.

Starting off

Check before starting-off

■ Tyre pressure and condition 3 143,
3 174.

■ Engine oil level and fluid levels
3 127.

■ All windows, mirrors, exterior
lighting and number plates are free
from dirt, snow and ice and are
operational.

■ Proper position of mirrors, seats,
and seat belts 3 28, 3 34,
3 40.

■ Brake function at low speed,
particularly if the brakes are wet.

18 In brief

Starting the engine

■ Turn key to position MAR

■ move the steering wheel slightly to
release the steering wheel lock

■ operate clutch and brake

■ manual transmission automated:
operate brake, the transmission
automatically shifts to N (neutral)

■ do not operate accelerator pedal

■ diesel engines: turn the key to
position MAR for preheating and
wait until control indicator ! goes
out

■ turn key to position AVV and
release

Starting the engine 3 102.

Stop-start system

If the vehicle is at a low speed or at a
standstill and certain conditions are
fulfilled, activate an Autostop as
follows:

■ Depress the clutch pedal

■ set the lever in neutral

■ release the clutch pedal
An Autostop is indicated when ^ is

displayed in the Driver Information
Centre 3 79.

To restart the engine, depress the
clutch pedal again.

Stop-start system 3 103.

In brief 19

Parking

■ Always apply the parking brake.
Activate the manual parking brake
without pressing the release button.
Apply as firmly as possible on a
downhill slope or uphill slope.
Depress foot brake at the same
time to reduce operating force.

■ Switch off the engine. Turn the
ignition key to position STOP and
remove it. Turn the steering wheel
until the steering wheel lock is felt
to engage.

■ If the vehicle is on a level surface or
uphill slope, engage first gear
before switching off the ignition. On
an uphill slope, turn the front
wheels away from the kerb.

If the vehicle is on a downhill slope,
engage reverse gear before
switching off the ignition. Turn the
front wheels towards the kerb.

■

Lock the vehicle with button e on
the radio remote control.

■ Do not park the vehicle on an easily
ignitable surface. The high
temperature of the exhaust system
could ignite the surface.

■ Close the windows.

■ The engine cooling fans may run
after the engine has been switched
off 3 126.

■ After running at high engine speeds
or with high engine loads, operate
the engine briefly at a low load or
run in neutral for
approx. 30 seconds before
switching off, in order to protect the
turbocharger.

Keys, locks 3 20, Laying the vehicle
up for a long period of time 3 125.

20 Keys, doors and windows

Keys, doors and windows

Keys, locks ................................... 20

Doors ........................................... 23

Vehicle security ............................ 27

Exterior mirrors ............................ 28

Interior mirrors ............................. 29

Windows ...................................... 29

Keys, locks

Keys

Replacement keys

The key number is specified in the
Car Pass or on a detachable tag.

The key number must be quoted
when ordering replacement keys as it
is a component of the immobiliser
system.

Locks 3 155.

Key with foldaway key section

Press button to extend. To fold the
key, first press the button.

Car Pass

The Car Pass contains security
related vehicle data and should
therefore be kept in a safe place.

When the vehicle is taken to a
workshop, this vehicle data is needed
in order to perform certain operations.

Radio remote control

Keys, doors and windows 21

Used to operate:

■ Central locking system 3 21

■ Anti-theft locking system 3 27

■ Power windows 3 29
The radio remote control has a range

of up to 5 metres. It can be restricted
by external influences. The hazard
warning flashers confirm operation.

Handle with care, protect from
moisture and high temperatures and
avoid unnecessary operation.

Fault

If the central locking system cannot
be operated with the radio remote
control, it may be due to the following:

■ Range exceeded

■ Battery voltage too low

■ Frequent, repeated operation of the
radio remote control while not in
range

■ Overload of the central locking
system by operating at frequent
intervals, the power supply is
interrupted for a short time

■ Interference from higher-power
radio waves from other sources

Unlocking 3 21.

Radio remote control battery replacement

Replace the battery as soon as the
range reduces.

Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.

Key with foldaway key section

Extend the key and remove the
battery holder by undoing the screw
with a suitable screwdriver. Remove
the battery holder from the key and
replace the battery (type CR 2032),
paying attention to the installation
position.

Refit the battery holder in the key and
secure the screw.

Central locking system

Unlocks and locks the front doors,
sliding side doors and load
compartment.

22 Keys, doors and windows

A pull on an interior door handle
unlocks and opens the respective
door.

For safety reasons, the vehicle
cannot be locked if the key is in the
ignition switch.

Unlocking

Note
In the event of an accident of a
certain severity, the vehicle unlocks
automatically.

Fuel cut-off system 3 85.

Van

Press button Ä: Front doors are
unlocked.

Press button Å: Rear doors / tailgate
and sliding side doors are unlocked.

Combi, Combo Tour
Press button Ä: All doors, including
rear doors / tailgate and sliding side
doors are unlocked.

Press button Å: Rear doors / tailgate
only are unlocked.

Note
If engaged, the anti-theft security
lock on the sliding side door remains
engaged even after unlocking the
vehicle with the remote control.

Anti-theft security lock 3 23.

Locking

Close all doors. If the doors are not
closed properly, the central locking
system will not work.

Press button e. All doors, including
rear doors / tailgate and sliding side
doors are locked.

Keys, doors and windows 23

Automatic locking
The vehicle can be configured to
automatically lock the doors when
vehicle speed exceeds 20 km/h.

Driver Information Centre 3 79.

Unlocking the load compartment from inside the vehicle

Press button Å: The load
compartment (rear doors / tailgate
and sliding side doors) are unlocked.

When the load compartment is
locked, the LED in the button is
illuminated.

Child locks

9 Warning

Use the child locks whenever
children are occupying the rear
seats.

Using a suitable tool, turn child lock
switch on sliding side door towards
the horizontal position. The door
cannot be opened from inside.

To deactivate, turn the child lock
switch to the vertical position.

Doors

Sliding door

Pull lever on interior handle and slide
door.

Caution

Ensure the side door is fully closed
and secure before driving the
vehicle.

Central locking system 3 21.

24 Keys, doors and windows

Caution

To avoid damage, do not attempt
to operate the sliding side door
when the fuel filler flap is open.

Refuelling 3 120.

Anti-theft security lock

To prevent the sliding side door from
being opened from the outside, open
the door and engage the anti-theft
security lock.

Using a suitable tool, turn the lock
switch on the sliding side door to
locked position 1. The door cannot be
opened from outside.

The anti-theft security lock remains
engaged even after unlocking the
vehicle with the remote control.

To disengage, turn the switch to
unlocked position 2.

Rear doors

The door is opened from inside the
vehicle by pressing down the interior
handle.

To open the left hand rear door pull
the outside handle.

Keys, doors and windows 25

The right hand rear door is released
using the lever.

9 Warning

The rear lights may be obscured if
the rear doors are open and the
vehicle is parked on the roadside.

Make other road users aware of
the vehicle, by using a warning
triangle or other equipment
specified in the road traffic
regulations.

The doors are retained in the 90º
position by locking stays. To open the
doors to 180º, push the latch and
swing open to the desired position.

9 Warning

Ensure extended opening doors
are secured when fully opened.

Opened doors may slam closed
due to the force of the wind!

Always close the right hand door
before the left hand door.

Central locking system 3 21.

Load compartment

Tailgate

Opening

Press the button underneath the
moulding.

9 Danger

Do not drive with the tailgate open
or ajar, e.g. when transporting
bulky objects, since toxic exhaust
gases, which can not be seen or

26 Keys, doors and windows

smelled, could enter the vehicle.
This can cause unconsciousness
and even death.

Caution

Before opening the tailgate check
overhead obstructions, such as a
garage door, to avoid damage to
the tailgate. Always check the
moving area above and behind the
tailgate.

Note
The installation of certain heavy
accessories onto the tailgate may
affect its ability to remain open.

Closing

Use the interior handle.
Ensure tailgate is fully closed before

driving.
Central locking system 3 21.

Emergency tailgate opening from inside the vehicle

An access hole (arrowed) enables the
tailgate latch to be released using a
suitable tool. Push lever to the right to
unlock and open the tailgate.

Keys, doors and windows 27

Vehicle security

Anti-theft locking system

9 Warning

Do not use the system if there are
people in the vehicle! The doors
cannot be unlocked from the
inside.

The system deadlocks all the doors.
All doors must be closed otherwise
the system cannot be activated.

The system is disabled automatically
on every door when:

■ unlocking the doors

■ turning the ignition switch to MAR

Activating

Press e on the radio remote control
twice.

Immobiliser

The system is part of the ignition
switch and checks whether the
vehicle is allowed to be started with
the key being used.

The immobiliser is activated
automatically after the key has been
removed from the ignition switch.

If the control indicator d illuminates
when starting, there is a fault in the
system; the engine cannot be started.
Switch off the ignition and repeat the
start attempt.

If d remains illuminated, attempt to
start the engine using the spare key
and seek the assistance of a
workshop.

Note
The immobiliser does not lock the
doors. Always lock the vehicle after
leaving it 3 21.

Control indicator d 3 78.

28 Keys, doors and windows

Exterior mirrors

Convex shape

The convex exterior mirror contains
an aspherical area and reduces blind
spots. The shape of the mirror makes
objects appear smaller, which will
affect the ability to estimate
distances.

Manual adjustment

Adjust mirrors by swivelling lever in
required direction.

The lower mirrors are not adjustable.

Electric adjustment

Select the relevant exterior mirror by
turning the control to left _ or right 6.
Then swivel the control to adjust the
mirror.

In position o no mirror is selected.

Folding

For pedestrian safety, the exterior
mirrors will swing out of their normal
mounting position if they are struck
with sufficient force. Reposition the
mirror by applying slight pressure to
the mirror housing.

Parking position

The exterior mirrors can be folded in
by pressing gently on the outer edge
of the housing, e.g. when in a
confined parking situation.

Keys, doors and windows 29

Heated mirrors

Operated by pressing the Ü button.
Heating works with the engine

running and is switched off
automatically after a short time.

Interior mirrors

Manual anti-dazzle

To reduce dazzle, adjust the lever on
the underside of the mirror housing.

Windows

Windscreen

Windscreen stickers

Do not attach stickers such as toll
road stickers or similar on the
windscreen in the area of the interior
mirror.

Manual windows

The door windows can be opened or
closed with the window winders.

Power windows

9 Warning

Take care when operating the
power windows. Risk of injury,
particularly to children.

If there are children on the rear
seats, switch on the child safety
system for the power windows.

30 Keys, doors and windows

Keep a close watch on the
windows when closing them.
Ensure that nothing becomes
trapped in them as they move.

Switch on ignition to operate power
windows.

Operate the switch for the respective
window by pushing to open or pulling
to close.

Pushing or pulling briefly: window
moves up or down in stages if the
switch is held.

Pushing or pulling firmly and then
releasing: window moves up or down
fully with safety function enabled. To
stop movement, operate the switch
once more in the same direction.

With the ignition key removed or in the
STOP position, the windows can be
operated for approx. 2 minutes and
are deactivated as soon as a door is
opened.

Safety function

If the window glass encounters
resistance during automatic closing, it
is immediately stopped and opened
again.

If the safety function is activated
five times in less than a minute, the
safety function is deactivated. The
windows will only close in stages and
not automatically.

Activate the window electronics by
opening the windows. The safety
function is restored and the windows
will operate normally.

Overload

If the windows are repeatedly
operated within short intervals, the
window operation is disabled for
some time.

Initialising the power windows

If the windows cannot be closed
automatically (e.g. after
disconnecting the vehicle battery),
activate the window electronics as
follows:

1. Close doors.

2. Switch on ignition.

3. Pull switch until the window is
closed and keep pulling for an
additional 5 seconds.

4. Repeat for each window.

Keys, doors and windows 31

Child safety system for rear windows

Press switch , to deactivate rear
door power windows.

To activate, press , again.

Operating windows from outside

The windows can be operated
remotely from outside the vehicle
when locking or unlocking the vehicle.

Central locking system 3 21.

Press and hold the Ä button to open
windows.

Press and hold the e button to close
windows.

Release button to stop window
movement.

Rear windows

Opening rear windows

To open, move lever outwards until
the window is fully open.

To close, pull lever then push until
window is fully closed.

32 Keys, doors and windows

Heated rear window

Operated by pressing the Ü button.
Heating works with the engine

running and is switched off
automatically after a short time.

Sun visors

The sun visors can be folded down or
swivelled to the side to prevent
dazzling.

If the sun visors have integral mirrors,
the mirror covers should be closed
when driving.

A ticket holder is located on the
backside of the sun visor.

Seats, restraints 33

Seats, restraints

Head restraints ............................ 33

Front seats ................................... 34

Rear seats ................................... 37

Seat belts ..................................... 39

Airbag system .............................. 42

Child restraints ............................. 48

Head restraints

Position

9 Warning

Only drive with the head restraint
set to the proper position.

The upper edge of the head restraint
should be at upper head level. If this
is not possible for extremely tall
people, set to highest position, and
set to lowest position for small people.

Adjustment

Front head restraints, height
adjustment

Press the button, adjust height and
engage.

34 Seats, restraints

Rear head restraints, height
adjustment

Pull the head restraint upwards or
press the catch to release and push
the head restraint downwards.

Removal

Rear head restraints, removal
Press both catches, pull the head
restraint upwards and remove.

Secure the removed head restraint in
the load compartment.

Note
Approved accessories may only be
attached if the seat is not in use.

Front seats

Seat position

9 Warning

Only drive with the seat correctly
adjusted.

Sit with buttocks as far back against

■
the backrest as possible. Adjust the
distance between the seat and the
pedals so that legs are slightly
angled when pressing the pedals.
Slide the front passenger seat as
far back as possible.

■ Sit with shoulders as far back
against the backrest as possible.
Set the backrest to an angle so that
it is possible to reach the steering
wheel with arms slightly bent.
Maintain contact between
shoulders and the backrest when
turning the steering wheel. Do not
tilt the backrest too far back. We
recommend a maximum angle of
approx. 25°.

■ Adjust the steering wheel 3 62.

■ Set the seat high enough to have a
clear field of vision on all sides and
on all display instruments. There
should be at least one hand of
clearance between head and the
roof frame. Thighs should rest
lightly on the seat without pressing
into it.

■ Adjust the head restraint 3 33.

■ Adjust the height of the seat belt
3 40.

Seat adjustment

Drive only with seats and backrests
properly engaged.

Seats, restraints 35

9 Danger

Do not sit nearer than 25 cm from
the steering wheel, to permit safe
airbag deployment.

9 Warning

Never adjust seats while driving as
they could move uncontrollably.

9 Warning

Never store any objects under the
seats except in the underseat
storage compartment 3 55.

Seat positioning

Pull handle, slide seat, release
handle.

Seat backrests

Turn handwheel. Do not lean on
backrest when adjusting.

36 Seats, restraints

Seat height

Lever pumping motion
up = higher

down = lower

Operate lever and adjust body weight
on seat to raise or lower it.

Armrest

Raise or lower the armrest as
required.

Heating

Activate seat heating by pressing
button ß for the respective front seat
with the ignition on.

Activation is indicated by the LED in
the button.

Pressing button ß once more
deactivates seat heating.

Prolonged use for people with
sensitive skin is not recommended.

Seats, restraints 37

Rear seats

9 Warning

Never adjust seats while driving as
they could move uncontrollably.

Folding the seats

The load compartment area can be
increased by folding up the rear
seats.

9 Warning

When folding the seat use caution

- beware of moving parts. Ensure
the seat is secure when
completely folded.

■ Lower the head restraint and move
the seat belt to one side.

■ Remove the load compartment
cover if necessary 3 56.

■ Pull the release lever and fold down
the backrest onto the seat cushion.

■ Pull the lower strap and fold the
seat assembly forwards.

■ Secure the folded seat in the
upright position by attaching the
flexible cord located on the seat
frame, to the rear seat head
restraint.

Unfolding the seats

■ To lower the rear seat, remove the
flexible cord and lower the seat
assembly to the floor, ensuring the
rear support is located on the
anchor point and securely latched.

■ Raise the backrest and adjust the
head restraint.

■ The backrest is properly engaged
when the red mark on the release
lever is no longer visible.

Removing the seats

■ Remove the seat head restraint
3 33 and remove load
compartment cover if necessary
3 56.

38 Seats, restraints

■ With the seat folded in the upright
position, push the release lever and
remove the seat assembly.

■ Store the head restraint on the rear
of the seat frame.

Installing the seats

■ Attach the seat assembly front
supports on the anchor points.

■ Push the release lever to ensure
the seat is securely latched.

■ Remove the head restraint from the
rear of the seat frame.

■ Lower the seat assembly to the
floor, ensuring the rear support is
located on the anchor point and
securely latched.

■ Raise the backrest and replace the
head restraint.

■ The backrest is properly engaged
when the red mark on the release
lever is no longer visible.

9 Warning

When installing the seat, ensure
that the seat is properly located on
the anchor points, the locking
catches are fully engaged, and the
backrest is returned to the correct
position.

Seats, restraints 39

Seat belts

The seat belts are locked during
heavy acceleration or deceleration of
the vehicle holding the occupants in
the sitting position. Therefore the risk
of injury is considerably reduced.

9 Warning

Fasten seat belt before each trip.
In the event of an accident, people

not wearing seat belts endanger
their fellow occupants and
themselves.

Seat belts are designed to be used by
only one person at a time. Child
restraint system 3 48.

Periodically check all parts of the belt
system for damage, pollution and
proper functionality.

Have damaged components
replaced. After an accident, have the
belts and triggered belt pretensioners
replaced by a workshop.

Note
Make sure that the belts are not
damaged by shoes or sharp-edged
objects or trapped. Prevent dirt from
getting into the belt retractors.

Seat belt reminder X 3 73.

Belt force limiters

On the front seats, stress on the body
is reduced by the gradual release of
the belt during a collision.

Belt pretensioners

In the event of a head-on or rear-end
collision of a certain severity, the front
seat belts are tightened.

Warning

9

Incorrect handling (e.g. removal or
fitting of belts) can trigger the belt
pretensioners.

Deployment of the belt pretensioners
is indicated by continuous illumination
of control indicator v 3 73.

Triggered belt pretensioners must be
replaced by a workshop. Belt
pretensioners can only be triggered
once.

Note
Do not affix or install accessories or
other objects that may interfere with
the operation of the belt
pretensioners. Do not make any
modifications to belt pretensioner
components as this will invalidate
the approval of your vehicle.

40 Seats, restraints

Three-point seat belt

Fastening

Withdraw the belt from the retractor,
guide it untwisted across the body
and insert the latch plate into the
buckle. Tighten the lap belt regularly
whilst driving by pulling the shoulder
belt.

Seat belt reminder X 3 73.

Loose or bulky clothing prevents the
belt from fitting snugly. Do not place
objects such as handbags or mobile
phones between the belt and your
body.

9 Warning

The belt must not rest against hard
or fragile objects in the pockets of
your clothing.

Height adjustment

1. Pull belt out slightly.

2. Press button down.

3. Adjust height and engage.

Seats, restraints 41

Adjust the height so that the belt lies
across the shoulder. It must not lie
across the throat or upper arm.

Do not adjust while driving.

Removing

To release belt, press red button on
belt buckle.

Seat belts on the rear seats

The seat belt for the rear centre seat
can only be withdrawn from the
retractor if the backrest is in the rear
position.

Using the seat belt while pregnant

9 Warning

The lap belt must be positioned as
low as possible across the pelvis
to prevent pressure on the
abdomen.

42 Seats, restraints

Airbag system

The airbag system consists of a
number of individual systems
depending on the scope of
equipment.

When triggered, the airbags inflate
within milliseconds. They also deflate
so quickly that it is often unnoticeable
during the collision.

Note
Depending on the severity of a
collision, the fuel system may also
be cut-off and the engine switched
off automatically, for safety reasons.
Resetting the fuel cut-off system;
refer to "Fuel system messages"
3 85.

Note
Expiry dates for replacing the airbag
system components may be found
on the label inside the glovebox.
Contact a workshop to have the
airbag system components
replaced.

9 Warning

If handled improperly the airbag
systems can be triggered in an
explosive manner.

Note
The airbag systems and belt
pretensioner control electronics are
located in the centre console area.
Do not put any magnetic objects in
this area.

Do not fix any objects onto the airbag
covers and do not cover them with
other materials.

Each airbag is triggered only once.
Have deployed airbags replaced by
a workshop. Furthermore, it might be
necessary to have the steering
wheel, the instrument panel, parts of
the panelling, the door seals,
handles and the seats replaced.

Do not make any modifications to
the airbag system as this will
invalidate the vehicle type approval.

9 Warning

When the airbags inflate, escaping
hot gases may cause burns.

Control indicator v for airbag systems
3 73.

Fault

If there is a fault in the airbag and belt
tensioner system, the control
indicator v illuminates in the
instrument cluster. The system is not
operational.

Have the cause of the fault remedied
by a workshop.

Control indicator v 3 73.

Child restraint systems on front
passenger seat with airbag
systems

Warning according to ECE R94.02:

Seats, restraints 43

EN: NEVER use a rear-facing child
restraint system on a seat protected
by an ACTIVE AIRBAG in front of it,
DEATH or SERIOUS INJURY to the
CHILD can occur.

DE: Nach hinten gerichtete
Kindersitze NIEMALS auf einem Sitz
verwenden, der durch einen davor
befindlichen AKTIVEN AIRBAG
geschützt ist, da dies den TOD oder
SCHWERE VERLETZUNGEN DES
KINDES zur Folge haben kann.

FR: NE JAMAIS utiliser un siège
d'enfant orienté vers l'arrière sur un
siège protégé par un COUSSIN
GONFLABLE ACTIF placé devant lui,

sous peine d'infliger des
BLESSURES GRAVES, voire
MORTELLES à l'ENFANT.

ES: NUNCA utilice un sistema de
retención infantil orientado hacia
atrás en un asiento protegido por un
AIRBAG FRONTAL ACTIVO. Peligro
de MUERTE o LESIONES GRAVES
para el NIÑO.

RU: ЗАПРЕЩАЕТСЯ
устанавливать детское
удерживающее устройство лицом
назад на сиденье автомобиля,
оборудованном фронтальной
подушкой безопасности, если
ПОДУШКА НЕ ОТКЛЮЧЕНА! Это
может привести к СМЕРТИ или
СЕРЬЕЗНЫМ ТРАВМАМ
РЕБЕНКА.

NL: Gebruik NOOIT een achterwaarts
gericht kinderzitje op een stoel met
een ACTIEVE AIRBAG ervoor, om
DODELIJK of ERNSTIG LETSEL van
het KIND te voorkomen.

DA: Brug ALDRIG en bagudvendt
autostol på et forsæde med AKTIV
AIRBAG, BARNET kan komme i
LIVSFARE eller komme ALVORLIGT
TIL SKADE.

SV: Använd ALDRIG en bakåtvänd
barnstol på ett säte som skyddas med
en framförvarande AKTIV AIRBAG.
DÖDSFALL eller ALLVARLIGA
SKADOR kan drabba BARNET.

FI: ÄLÄ KOSKAAN sijoita taaksepäin
suunnattua lasten turvaistuinta
istuimelle, jonka edessä on
AKTIIVINEN TURVATYYNY, LAPSI
VOI KUOLLA tai VAMMAUTUA
VAKAVASTI.

NO: Bakovervendt
barnesikringsutstyr må ALDRI brukes
på et sete med AKTIV
KOLLISJONSPUTE foran, da det kan
føre til at BARNET utsettes for
LIVSFARE og fare for ALVORLIGE
SKADER.

PT: NUNCA use um sistema de
retenção para crianças voltado para
trás num banco protegido com um
AIRBAG ACTIVO na frente do

44 Seats, restraints

mesmo, poderá ocorrer a PERDA DE
VIDA ou FERIMENTOS GRAVES na
CRIANÇA.

IT: Non usare mai un sistema di
sicurezza per bambini rivolto
all'indietro su un sedile protetto da
AIRBAG ATTIVO di fronte ad esso:
pericolo di MORTE o LESIONI
GRAVI per il BAMBINO!

EL: ΠΟΤΕ μη χρησιμοποιείτε παιδικό
κάθισμα ασφαλείας με φορά προς τα
πίσω σε κάθισμα που προστατεύεται
από μετωπικό ΕΝΕΡΓΟ ΑΕΡΟΣΑΚΟ,
διότι το παιδί μπορεί να υποστεί
ΘΑΝΑΣΙΜΟ ή ΣΟΒΑΡΟ
ΤΡΑΥΜΑΤΙΣΜΟ.

PL: NIE WOLNO montować fotelika
dziecięcego zwróconego tyłem do
kierunku jazdy na fotelu, przed
którym znajduje się WŁĄCZONA
PODUSZKA POWIETRZNA.
Niezastosowanie się do tego
zalecenia może być przyczyną
ŚMIERCI lub POWAŻNYCH
OBRAŻEŃ u DZIECKA.

TR: Arkaya bakan bir çocuk emniyet
sistemini KESİNLİKLE önünde bir
AKTİF HAVA YASTIĞI ile

korunmakta olan bir koltukta
kullanmayınız. ÇOCUK ÖLEBİLİR
veya AĞIR ŞEKİLDE
YARALANABİLİR.

UK: НІКОЛИ не використовуйте
систему безпеки для дітей, що
встановлюється обличчям назад,
на сидінні з УВІМКНЕНОЮ
ПОДУШКОЮ БЕЗПЕКИ, інакше це
може призвести до СМЕРТІ чи
СЕРЙОЗНОГО ТРАВМУВАННЯ
ДИТИНИ.

HU: SOHA ne használjon hátrafelé
néző biztonsági gyerekülést előlről
AKTÍV LÉGZSÁKKAL védett ülésen,
mert a GYERMEK HALÁLÁT vagy
KOMOLY SÉRÜLÉSÉT okozhatja.

HR: NIKADA nemojte koristiti sustav
zadržavanja za djecu okrenut prema
natrag na sjedalu s AKTIVNIM
ZRAČNIM JASTUKOM ispred njega,
to bi moglo dovesti do SMRTI ili
OZBILJNJIH OZLJEDA za DIJETE.

SL: NIKOLI ne nameščajte otroškega
varnostnega sedeža, obrnjenega v
nasprotni smeri vožnje, na sedež z
AKTIVNO ČELNO ZRAČNO

BLAZINO, saj pri tem obstaja
nevarnost RESNIH ali SMRTNIH
POŠKODB za OTROKA.

SR: NIKADA ne koristiti bezbednosni
sistem za decu u kome su deca
okrenuta unazad na sedištu sa
AKTIVNIM VAZDUŠNIM
JASTUKOM ispred sedišta zato što
DETE može da NASTRADA ili da se
TEŠKO POVREDI.

MK: НИКОГАШ не користете детско
седиште свртено наназад на
седиште заштитено со АКТИВНО
ВОЗДУШНО ПЕРНИЧЕ пред него,
затоа што детето може ДА ЗАГИНЕ
или да биде ТЕШКО ПОВРЕДЕНО.

BG: НИКОГА не използвайте
детска седалка, гледаща назад,
върху седалка, която е защитена
чрез АКТИВНА ВЪЗДУШНА
ВЪЗГЛАВНИЦА пред нея - може да
се стигне до СМЪРТ или
СЕРИОЗНО НАРАНЯВАНЕ на
ДЕТЕТО.

RO: Nu utilizaţi NICIODATĂ un scaun
pentru copil îndreptat spre partea din
spate a maşinii pe un scaun protejat
de un AIRBAG ACTIV în faţa sa;

Seats, restraints 45

acest lucru poate duce la DECESUL
sau VĂTĂMAREA GRAVĂ a
COPILULUI.

CS: NIKDY nepoužívejte dětský
zádržný systém instalovaný proti
směru jízdy na sedadle, které je
chráněno před sedadlem AKTIVNÍM
AIRBAGEM. Mohlo by dojít k
VÁŽNÉMU PORANĚNÍ nebo ÚMRTÍ
DÍTĚTE.

SK: NIKDY nepoužívajte detskú
sedačku otočenú vzad na sedadle
chránenom AKTÍVNYM AIRBAGOM,
pretože môže dôjsť k SMRTI alebo
VÁŽNYM ZRANENIAM DIEŤAŤA.

LT: JOKIU BŪDU nemontuokite atgal
atgręžtos vaiko tvirtinimo sistemos
sėdynėje, prieš kurią įrengta AKTYVI
ORO PAGALVĖ, nes VAIKAS GALI
ŽŪTI arba RIMTAI SUSIŽALOTI.

LV: NEKĀDĀ GADĪJUMĀ
neizmantojiet uz aizmuguri vērstu
bērnu sēdeklīti sēdvietā, kas tiek
aizsargāta ar tās priekšā uzstādītu
AKTĪVU DROŠĪBAS SPILVENU, jo
pretējā gadījumā BĒRNS var gūt
SMAGAS TRAUMAS vai IET BOJĀ.

ET: ÄRGE kasutage tahapoole
suunatud lapseturvaistet istmel, mille
ees on AKTIIVSE TURVAPADJAGA
kaitstud iste, sest see võib
põhjustada LAPSE SURMA või
TÕSISE VIGASTUSE.

Beyond the warning required by ECE
R94.02, for safety reasons never use
a forward-facing child restraint
system on the front passenger seat
with active front airbag.

9 Danger

Do not use a child restraint system
on the passenger seat with active
front airbag.

Airbag deactivation 3 46.

Front airbag system

The front airbag system consists of
one airbag in the steering wheel and
one in the instrument panel on the
front passenger side. These can be
identified by the word AIRBAG.

Additionally there is a warning label
on the passenger's sun visor.

Child restraint systems 3 48.
Airbag deactivation 3 46.

46 Seats, restraints

The front airbag system is triggered in
the event of a front-end impact of a
certain severity. The ignition must be
switched on.

The inflated airbags cushion the
impact, thereby reducing the risk of
injury to the upper body and head of
the front seat occupants
considerably.

9 Warning

Optimum protection is only
provided when the seat is in the
proper position 3 34.

Keep the area in which the airbag
inflates clear of obstructions.

Fit the seat belt correctly and
engage securely. Only then the
airbag is able to protect.

Side airbag system

The side airbag system consists of an
airbag in each front seat backrest.
This can be identified by the word
AIRBAG.

The side airbag system is triggered in
the event of a side impact of a certain
severity. The ignition must be
switched on.

The inflated airbags cushion the
impact, thereby reducing the risk of
injury to the upper body and pelvis in
the event of a side-on collision
considerably.

9 Warning

Keep the area in which the airbag
inflates clear of obstructions.

Note
Only use protective seat covers that
have been approved for the vehicle.
Be careful not to cover the airbags.

Airbag deactivation

The front passenger airbag system
must be deactivated if a child restraint
system is to be fitted on this seat.

The side airbag systems, the belt
pretensioners and all driver airbag
systems will remain active.

The front passenger airbag system
can be deactivated via the settings
menu in the Driver Information Centre
3 79.

Seats, restraints 47

Deactivate the front passenger airbag
system as follows:

1. Press the SETq button once to
access the settings menu.

2. Press SETq again (repeatedly)
to cycle through the menu
functions until menu option Pass
bag (in Standard version)

- or ­Passenger bag (in Multifunction

version)
is displayed.

3. Press the R or S button to switch
from Pass bag On to Pass bag
off (Standard version)

- or ­from Passenger bag On to

Passenger bag Off (Multifunction
version)

4. Press SETq to confirm selection;
A confirmation message appears
in the display.

5. Press the R or S button to select
Yes.

6. Press SETq briefly to confirm
deactivation and automatically
return to the previous display
screen.

Front passenger seat airbags are
deactivated and will not inflate in the
event of a collision. Control indicator
* illuminates continuously in the
instrument cluster. A child restraint
system can be installed in
accordance with the chart Child
restraint installation locations 3 50.

9 Danger

Risk of fatal injury for a child using
a child restraint system on a seat
with activated front passenger
airbag.

Risk of fatal injury for an adult
person on a seat with deactivated
front passenger airbag.

As long as the control indicator * is
not illuminated, the front passenger
airbag system will inflate in the event
of a collision.

If control indicators * and v are
illuminated at the same time, there is
a system failure. The status of the
system is not discernible, therefore
no person is allowed to occupy the
front passenger seat. Contact a
workshop immediately.

Change status only when the vehicle
is stationary with the ignition off. The
status remains until the next change.

Control indicator for airbag
deactivation 3 74.

48 Seats, restraints

Reactivating front passenger airbag
system - see Driver Information
Centre 3 79.

Child restraints

Child restraint systems

We recommend the Opel child
restraint system which is tailored
specifically to the vehicle.

When a child restraint system is being
used, pay attention to the following
usage and installation instructions
and also those supplied with the child
restraint system.

Always comply with local or national
regulations. In some countries, the
use of child restraint systems is
forbidden on certain seats.

9 Warning

When using a child restraint
system on the front passenger
seat, the airbag systems for the
front passenger seat must be
deactivated; if not, the triggering of
the airbags poses a risk of fatal
injury to the child.

This is especially the case if rear­facing child restraint systems are
used on the front passenger seat.

Selecting the right system

The rear seats are the most
convenient location to fasten a child
restraint system.

Children should travel facing
rearwards in the vehicle as long as
possible. This makes sure that the
child's backbone, which is still very
weak, is under less strain in the event
of an accident.

Suitable restraint systems comply
with ECE 44-03 or ECE 44-04. Check
local laws and regulations for
mandatory use of child restraint
systems.

Ensure that the child restraint system
to be installed is compatible with the
vehicle type.

Ensure that the mounting location of
the child restraint system within the
vehicle is correct.

Allow children to enter and exit the
vehicle only on the side facing away
from the traffic.

When the child restraint system is not
in use, secure the seat with a seat belt
or remove it from the vehicle.

Note
Do not stick anything on the child
restraint systems and do not cover
them with any other materials.

A child restraint system which has
been subjected to stress in an
accident must be replaced.

Seats, restraints 49

50 Seats, restraints

Child restraint installation locations

Permissible options for fitting a child restraint system

Front passenger seat Second row Third row

Weight and age class

Group 0: up to 10 kg
or approx. 10 months

Group 0+: up to 13 kg
or approx. 2 years

Group I: 9 to 18 kg
or approx. 8 months to 4 years

Group II: 15 to 25 kg
or approx. 3 to 7 years

Group III: 22 to 36 kg
or approx. 6 to 12 years

1

= Only if front airbag system is deactivated. When securing with a three-point seat belt, move seat height adjustment

to uppermost position and ensure that the seat belt runs forwards from the upper anchorage point. Adjust seat
backrest inclination as far as necessary to a vertical position to ensure that the belt is tight on the buckle side.

= Vehicle seat available with ISOFIX attachments. When attaching using ISOFIX, only the ISOFIX child restraint

<

systems permitted for the vehicle may be used.
U = Universal suitability in conjunction with three-point seat belt.
X = No child restraint system permitted in this weight class.

activated airbag deactivated airbag outboard seat centre seat

X

X

X

1

U

1

U

1

U

U, <

U, <

U, <

U X

U X

U X

X X U U X

X X U U X

Seats, restraints 51

Permissible options for fitting an ISOFIX child restraint system

Weight class Size class Fixture

seat

Group 0: up to 10 kg E ISO/R1 X IL X X

Group 0+: up to 13 kg E ISO/R1 X IL X X

D ISO/R2 X IL X X

C ISO/R3 X

Group I: 9 to 18 kg D ISO/R2 X IL X X

C ISO/R3 X

B ISO/F2 X IUF X X

B1 ISO/F2X X IUF X X

A ISO/F3 X IUF X X

IL = Suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories.

The ISOFIX restraint system must be approved for the specific vehicle type.
IUF = Suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight class.
X = No ISOFIX child restraint system approved in this weight class.

On front passenger

On outboard seats
in the second row

1)

IL

1)

IL

On centre seat in
the second row

X X

X X

On the seats in
the third row

1)

The Isofix child seat can be installed by lifting the head restraint all the way up.

52 Seats, restraints

ISOFIX size class and seat device

A – ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg.
B – ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
B1 – ISO/F2X = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
C – ISO/R3 = Rear-facing child restraint system for children of maximum size in the weight class up to 18 kg.
D – ISO/R2 = Rear-facing child restraint system for smaller children in the weight class up to 18 kg.
E – ISO/R1 = Rear-facing child restraint system for young children in the weight class up to 13 kg.

Seats, restraints 53

ISOFIX child restraint systems

Fasten vehicle-approved ISOFIX
child restraint systems to the ISOFIX
mounting brackets. Specific vehicle
ISOFIX child restraint system
positions are marked in the table by
IL.

ISOFIX mounting brackets are
indicated by a label on the backrest.

Before fastening a child seat adjust
the head restraint to use position
3 33.

Top-tether fastening eyes

In addition to the ISOFIX mounting,
fasten the Top-Tether strap to the
Top-Tether fastening eyes. The strap
must run between the two guide rods
of the head restraint.

ISOFIX child restraint systems of
universal category positions are
marked in the table by IUF.

54 Storage

Storage

Storage compartments ................ 54

Load compartment ....................... 56

Roof rack system ......................... 59

Loading information ..................... 60

Storage compartments

9 Warning

Do not store heavy or sharp
objects in the storage
compartments. Otherwise vehicle
occupants could be injured by
objects being thrown around in the
event of hard braking, a sudden
change in direction or an accident.

Instrument panel storage

Storage compartments are located in
the instrument panel.

Document holder

Pull the rear of the document holder
upwards from the instrument panel
and rest in tilted position.

To fold away, lower the document
holder back into the instrument panel,
pressing down until it engages
audibly.

Storage 55

Glovebox

Pull lever to open the glovebox cover.
Depending on version, the glovebox

may be lockable.
The glovebox should be closed whilst

driving.

Cupholders

Cupholders are located in the console
between the front seats.

The cupholders can also be used to
hold the portable ashtray unit 3 68.

Overhead console

Store only lightweight items such as
paperwork or maps in the overhead
console.

Underseat storage

Pull the loop on the seat cushion to
gain access to the storage area.

56 Storage

Load compartment

Folding down rear seat
backrests

The rear seat backrest is divided into
two parts. Both parts can be folded
down.

Remove the load compartment cover
if necessary.

Press and hold the catch, then push
the head restraints down.

Pull the release lever on one or both
sides and fold down the backrests
onto the seat cushion.

Pull lever to release, the seat base is
tensioned and will start to rise
automatically.

Fold the seat forward completely.

To fold up, lower seats to the floor
until they engage audibly. Raise
backrests and guide them into an
upright position until they engage
audibly.

The backrests are properly engaged
when both red marks on the release
levers are no longer visible.

Ensure that the seat belts are
positioned correctly before returning
the seats to the upright position.

9 Warning

Only drive the vehicle if the
backrests are securely locked into
position. Otherwise there is a risk
of personal injury or damage to the
load or vehicle in the event of
heavy braking or a collision.

Load compartment cover

Extendable load compartment cover

Do not place any heavy or sharp­edged objects on the extendable load
compartment cover.

Storage 57

Closing

Pull the cover towards the rear using
the handle and engage it in the
retainers at the sides.

Opening

Remove load compartment cover
from the retainers at the sides. Hold
the cover and guide it until it is fully
rolled up.

Removing

Open the load compartment cover.
Pull the release lever and lift cover

from retainers.

Installing
Insert either side of the load
compartment cover in the recess, pull
the release lever. Insert the load
compartment cover and engage.

58 Storage

Rear parcel shelf

The rear parcel shelf consists of two
parts - a front part and rear part. The
front part can be opened or closed,
allowing for greater flexibility in the
load compartment.

Do not place any excessively heavy
or sharp-edged objects on the rear
parcel shelf.

9 Warning

Always make sure that the load in
the vehicle is securely stowed.
Otherwise objects can be thrown
around inside the vehicle and
cause personal injury or damage
to the load or car.

The rear parcel shelf can be installed
in 2 positions, i.e. the upper position

or the lower position. In the lower
position, the maximum load
permissible is 70 kg.

Removing
If the rear seats are in the folded
position, remove the parcel shelf and
store it horizontally between the back
of the front seats and the folded rear
seats.

Caution

For safety reasons, do not place
loads on the folded rear seats.

Storage 59

To remove, lift the front part of the
parcel shelf by releasing it from the
front retainers (1) on both sides.

Lift the rear part of the parcel shelf by
releasing it from the rear retainers (2
and 3) on both sides.

Installing
Refit the parcel shelf by engaging in
front and rear retainers on both sides.

Lashing eyes

Van

The lashing eyes are designed to
secure items against slippage, e.g.
using lashing straps or a luggage net.

Combo Tour

Roof rack system

Roof rack

For safety reasons and to avoid
damage to the roof, the vehicle
approved roof rack system is
recommended. Contact a workshop
for further information.

Follow the installation instructions
and remove the roof rack when not in
use.

Mounting roof rack

60 Storage

To fasten a roof rack, insert the
mounting bolts in the holes indicated
in the illustration.

Loading information

■ Heavy objects in the load
compartment should be evenly
distributed and placed as far
forward as possible. If objects can
be stacked, the heavier objects
should be placed at the bottom.

■ Secure objects with lashing straps
attached to lashing eyes 3 59.

■ Secure loose objects in load
compartment to prevent them from
sliding.

■ When transporting objects in the
load compartment, the backrests of
the rear seats must not be tilted
forwards or folded down.

■ Do not allow the load to protrude
above the upper edge of the
backrests.

■ Do not place any objects on the
extendable load compartment
cover 3 56 or the instrument panel,
and do not cover the sensor on top
of the instrument panel 3 97.

■ The load must not obstruct the
operation of the pedals, parking
brake and gear selector, or hinder
the freedom of movement of the
driver. Do not place any unsecured
objects in the interior.

■ Do not drive with an open load
compartment.

9 Warning

Always make sure that the load in
the vehicle is securely stowed.
Otherwise objects can be thrown
around inside the vehicle and
cause personal injury or damage
to the load or car.

■ The payload is the difference
between the permitted gross
vehicle weight (see identification
plate 3 161) and the EC kerb
weight.

To calculate the payload, enter the
data for your vehicle in the Weights
table at the front of this manual.

The EC kerb weight includes
weights for the driver (68 kg),

luggage (7 kg) and all fluids (tank
90 % full).

Optional equipment and
accessories increase the kerb
weight.

■ Driving with a roof load increases
the sensitivity of the vehicle to
cross-winds and has a detrimental
effect on vehicle handling due to
the vehicle's higher centre of
gravity. Distribute the load evenly
and secure it properly with retaining
straps. Adjust the tyre pressure and
vehicle speed according to the load
conditions. Check and retighten the
straps frequently.

Do not drive faster than 120 km/h.
The permissible roof load (which

includes the weight of the roof rack)
is 100 kg. The roof load is the
combined weight of the roof rack
and the load.

Storage 61

62 Instruments and controls

Instruments and controls

Controls ....................................... 62

Warning lights, gauges and indi‐

cators ........................................... 68

Information displays ..................... 79

Vehicle messages ........................ 85

Trip computer ............................... 86

Controls

Steering wheel adjustment

Unlock lever, adjust steering wheel,
then engage lever and ensure it is
fully locked.

Do not adjust steering wheel unless
vehicle is stationary and steering
wheel lock has been released.

Steering wheel controls

The Infotainment system and a
connected mobile phone can be
operated via the controls on the
steering wheel.

Further information is available in the
Infotainment system manual.

Instruments and controls 63

Horn

Press j.

Windscreen wiper/washer

Windscreen wiper

Twist lever:

= off

§

Ç

= intermittent wiping

È

= slow

É

= fast

For a single wipe when the
windscreen wiper is off, move the
lever up.

Do not use if the windscreen is frozen.
Switch off in car washes.

Adjustable wiper interval
Wiper lever in position Ç.

The windscreen wiper will
automatically adapt to the speed of
the vehicle.

Windscreen washer

Pull lever briefly, washer fluid is
sprayed onto the windscreen and the
wiper wipes a few times.

Pull lever and hold, washer fluid is
sprayed onto the windscreen and
wiper wipes until the lever is released.

Washer fluid 3 129, Wiper blade
replacement 3 131.

64 Instruments and controls

Rear window wiper/washer

Twist to activate the rear window
wiper.

Push lever. Washer fluid is sprayed
onto the rear window and the wiper
wipes a few times.

Do not use if the rear window is
frozen.

Switch off in car washes.
The rear window wiper comes on

automatically when the windscreen
wiper is switched on and reverse gear
is engaged.

Outside temperature

Outside temperature is shown in the
Driver Information Centre 3 79.

9 Warning

The road surface may already be
icy even though the display
indicates a few degrees above
0 °C.

Clock

Depending on model variant, the
current time and/or date may appear
in the Driver Information Centre
3 79.

Values can be adjusted via the
SETq, R and S buttons on the
instrument panel.

Instruments and controls 65

Set time in Driver Information Centre - Standard version

1. Press the SETq button once to
access the settings menu.

2. Scroll through the menu options
using the R or S buttons
until HOUR is displayed.

3. Press SETq to access this menu
option; the hours will flash in the
display.

4. Press R or S to increase or
decrease the displayed value.

5. Press SETq to confirm changes;
the minutes will flash in the
display.

6. Press R or S to increase or
decrease the displayed value.

7. Press SETq briefly to confirm
changes and automatically return
to the previous display screen.

Set time and date in Driver
Information Centre ­Multifunction version

Setting the time
After accessing this menu option, it is
possible to either set the time or
change the clock mode between
12 hour and 24 hour clock.

Press the SETq button once to
access the settings menu.

Scroll through the menu options using
the R or S buttons until Set time is
displayed.

Press SETq to access this menu
option; Time and Mode are displayed.

To set the time:

1. Press R or S to select Time and
press SETq to access this
submenu option; the hours will
flash in the display

2. Press R or S to increase or
decrease the displayed value.

3. Press SETq to confirm changes;
the minutes will flash in the
display.

66 Instruments and controls

4. Press R or S to increase or
decrease the displayed value.

5. Press SETq briefly to confirm
changes and automatically return
to the previous display screen.

To change the clock mode between
12 hour and 24 hour clock:

1. Press R or S to select Mode and
press SETq to access this
submenu option; the display will
flash.

2. Press R or S to change clock
mode between 12h and 24h.

3. Press SETq briefly to confirm
changes and automatically return
to the previous display screen.

Setting the date

1. Press the SETq button once to
access the settings menu.

2. Scroll through the menu options
using the R or S buttons until Set
date is displayed.

3. Press SETq to access this menu
option; the year will flash in the
display.

4. Press R or S to increase or
decrease the displayed value.

5. Press SETq to confirm changes;
the month will flash in the display.

6. Press R or S to increase or
decrease the displayed value.

7. Press SETq to confirm changes;
the day will flash in the display.

8. Press R or S to increase or
decrease the displayed value.

9. Press SETq briefly to confirm
changes and automatically return
to the previous display screen.

Power outlets

A 12 Volt power outlet is located in the
centre console.

Rear power outlets

Depending on model variant,12 Volt
power outlets are located at the
sidewall in the load compartment.

Instruments and controls 67

Short wheelbase van

Long wheelbase van

Combo Tour

Do not exceed the maximum power
consumption of 180 watts.

With ignition off, the power outlets are
deactivated. Additionally the power
outlets are deactivated in the event of
low battery voltage.

Electrical accessories that are
connected must comply with the
electromagnetic compatibility
requirements laid down in
DIN VDE 40 839.

Do not connect any current-delivering
accessories, e.g. electrical charging
devices or batteries.

Do not damage the power outlets by
using unsuitable plugs.

If the tyre repair kit is in operation,
switch off all electrical consumers.
Tyre repair kit 3 145.

Cigarette lighter

The cigarette lighter is located in the
centre console.

Press in cigarette lighter. It switches
off automatically once the element is
glowing. Pull out lighter.

68 Instruments and controls

Ashtrays

Caution

To be used only for ash and not for
combustible rubbish.

The portable ashtray should be
placed in the cupholders in the centre
console.

Warning lights, gauges and indicators

Instrument cluster

The needles of the instruments briefly
rotate to the end position when the
ignition is switched on.

Speedometer

Indicates vehicle speed.

Odometer

Displays the recorded distance in km.
H may appear in the display until the

vehicle has travelled 100 km.

Trip odometer

Displays the recorded distance since
the last reset.

Depending on model variant, there
are two independent trip odometers
A or B which indicate how far the
vehicle has been driven since the last
reset.

Instruments and controls 69

To reset the trip odometer, press and
hold the TRIP button for a few
seconds while the relevant trip
odometer is displayed.

Tachometer

Displays the engine speed.
Drive in a low engine speed range for

each gear as much as possible.

Caution

If the needle is in the red warning
zone, the maximum permitted
engine speed is exceeded. Engine
at risk.

Fuel gauge

Displays the fuel level or gas level in
the tank depending on the operation
mode.

During natural gas operation, the
system automatically switches over to
petrol operation when the gas tanks
are empty 3 70. Fuel selector
3 119.

Control indicator $ illuminates if the
level in the tank is low.

Never run the tank dry.
Because of the fuel remaining in the

tank, the top-up quantity may be less
than the specified tank capacity.

The needle will point to 0 and control
indicator $ will flash to indicate a fault
in the system. Seek the assistance of
a workshop.

Low fuel control indicator $ 3 78.

70 Instruments and controls

CNG fuel gauge

In natural gas operation mode, the
four vertical bars next to CNG
correspond to the methane level in
the cylinders. As the fuel level
diminishes, the bars in the CNG fuel
gauge disappear.

CNG and the one remaining bar will
flash if the methane level in the
cylinders is low.

Refuelling 3 120.

Fuel selector

Pressing button Y in the centre
console switches between petrol and
natural gas operation. The LED 1
status shows the current operating
mode.

1 off = natural gas

operation.

1 illuminates = petrol operation.

During natural gas operation, if
control indicator Y illuminates in the
Driver Information Centre (DIC)
3 79, the natural gas tanks are
empty and petrol operation is
automatically engaged.

Fuel for natural gas operation 3 119,
Refuelling 3 120.

Engine coolant temperature gauge

Displays the coolant temperature.
C = engine operating

temperature not yet

reached
central
area
H = temperature too high

= normal operating

temperature

Instruments and controls 71

If control indicator $ illuminates in
conjunction with a message in the
Driver Information Centre 3 79 the
coolant temperature is too high. Seek
the assistance of a workshop.

Caution

If engine coolant temperature is
too high, stop vehicle, switch off
engine. Danger to engine. Check
coolant level.

Service display

Service display is available in
vehicles with Multifunction version of
the Driver Information Centre 3 79.

When the ignition is switched on, the
remaining distance before the next
service is due is shown briefly. Based
on driving conditions, the interval at
which a service will be indicated can
vary considerably.

When the remaining distance before
the next service is less than 2,000 km,
Serv. appears in the Driver
Information Centre. The service
reminder is repeated after every
additional 200 km and becomes more
frequent when the remaining distance
is below 200 km.

The vehicle needs a service. Seek the
assistance of a workshop.

The remaining distance to the next
service may also be viewed in the
Driver Information Centre by
selecting SERVICE from the settings
menu options 3 79.

Resetting the service display

After a service, the service display
must be reset by a workshop.

Control indicators

The control indicators described are
not present in all vehicles. The
description applies to all instrument
versions. Depending on the
equipment, the position of the control
indicators may vary.

When the ignition is switched on,
most control indicators will illuminate
briefly as a functionality test.

The control indicator colours mean:
red = danger, important

reminder
yellow = warning, information, fault
green = confirmation of activation
blue = confirmation of activation

72 Instruments and controls

Control indicators in the instrument cluster

Instruments and controls 73

Generic warning

9 illuminates yellow.
Depending on model variant, control

indicator 9 may illuminate
independently or in conjunction with
Æ, t, Z or r.

If 9 illuminates together with I; stop
engine immediately and seek the
assistance of a workshop.

Simultaneously a warning message
may be displayed in the Driver
Information Centre 3 79.

9 also illuminates if the fuel cut-off
switch is triggered, or if a fault is
detected in the engine oil pressure
sensor. Consult a workshop.

Fuel cut-off system 3 85.

Turn signal

2 or 3 flashes green.

Flashes

A turn signal or the hazard warning
flashers are activated.

Rapid flashing: failure of a turn signal
light or associated fuse, failure of turn
signal light on trailer.

Bulb replacement 3 132, Fuses
3 138.

Turn signals 3 90.

Seat belt reminder

Seat belt reminder for front seats

X for driver's seat and/or front
passenger seat illuminates or flashes
red.

Illuminates
When the ignition has been switched
on, control indicator X illuminates
briefly if driver's seat belt and/or front
passenger seat belt is not engaged. A
warning chime also sounds for a few
seconds.

Flashes
During driving X will flash and a

warning chime will sound for
90 seconds until the front seat belts
are fastened.

Fastening the seat belt 3 40.

9 Warning

Fasten seat belt before each trip.
In the event of an accident, people

not wearing seat belts endanger
their fellow occupants and
themselves.

To deactivate the seat belt reminder,
consult a workshop. Reactivation of
the warning chime for seat belt
reminder can be done via the Driver
Information Centre 3 79.

Note
The volume of the warning chime
can also be adjusted via the Driver
Information Centre 3 79.

Airbag and belt tensioners

v illuminates red.
When the ignition is switched on, the

control indicator illuminates for
approx. 4 seconds. If it does not
illuminate, does not go out after
4 seconds or illuminates whilst
driving, there is a fault in the airbag

74 Instruments and controls

system. Seek the assistance of a
workshop. The airbags and belt
pretensioners may fail to trigger in the
event of an accident.

Deployment of the belt pretensioners
or airbags is indicated by continuous
illumination of v.

9 Warning

Have the cause of the fault
remedied immediately by a
workshop.

Belt pretensioners, airbag system
3 39, 3 42.

Airbag deactivation

* illuminates yellow.
With the front passenger airbag

activated:
When the ignition is switched on, *

illuminates for approx. 4 seconds,
flashes for another 4 seconds and
then extinguishes.

With the front passenger airbag
deactivated:

*

permanently illuminates yellow.

Airbag deactivation 3 46.

9 Danger

Risk of fatal injury for a child using
a child restraint system together
with activated front passenger
airbag.

Risk of fatal injury for an adult
person with deactivated front
passenger airbag.

Charging system

p illuminates red.
Illuminates when the ignition is

switched on and extinguishes shortly
after the engine starts.

Illuminates when the engine is running

Stop, switch off engine. Battery is not
charging. Engine cooling may be
interrupted. The brake servo unit may
cease to be effective. Seek the
assistance of a workshop.

Malfunction indicator light

Z illuminates or flashes yellow.
Illuminates when the ignition is

switched on and extinguishes shortly
after the engine starts.

Illuminates when the engine is running

Fault in the emission control system.
The permitted emission limits may be
exceeded. Seek the assistance of a
workshop immediately.

Flashes when the engine is running

Fault that could lead to catalytic
converter damage. Ease up on the
accelerator until the flashing stops.
Seek the assistance of a workshop
immediately.

Brake system

R illuminates red.
Illuminates when the parking brake is

released if the brake fluid level is too
low 3 130.

Instruments and controls 75

9 Warning

Stop. Do not continue your
journey. Consult a workshop.

Illuminates if the brake vacuum servo
fails; the brake pedal becomes stiff
when pressed. The brake system
remains operational however,
assistance will be reduced. The
steering may also require
considerably more effort when
turning.

Illuminates after the ignition is
switched on if the parking brake is
applied 3 112.

Brake pad wear

F illuminates yellow.
The front brake pads are worn, seek

the assistance of a workshop
immediately.

Antilock brake system (ABS)

u illuminates yellow.

Illuminates for a few seconds after the
ignition is switched on. The system is
ready for operation when the control
indicator extinguishes.

If the control indicator does not
extinguish after a few seconds, or if it
illuminates while driving, there is a
fault in the ABS. The brake system
remains operational but without ABS
regulation.

Antilock brake system 3 112.

Upshift

[ or Ò illuminates in the Driver
Information Centre 3 79 when
gearshifting is recommended to
improve fuel economy.

Hill start assist

Z illuminates yellow.
Illuminates when the ignition is

switched on and extinguishes shortly
after the engine starts.

If the control indicator does not
extinguish after a few seconds, or if it
illuminates while driving, there is a

fault in the Hill start assist. Seek the
assistance of a workshop to have the
fault remedied.

The Electronic Stability Program
(ESP) control indicator x may also
illuminate 3 76 in conjunction with
Z.

Depending on model variant, 9 will
illuminate as an alternative if control
indicator Z is not present. A warning
message may also be displayed in
the Driver Information Centre 3 79.

Generic warning 9 3 73.
Hill start assist 3 113.

Ultrasonic parking assist

r illuminates yellow.
Fault in system
or
Fault due to sensors that are dirty or

covered by ice or snow
or

76 Instruments and controls

Interference due to external sources
of ultrasound. Once the source of
interference is removed, the system
will operate normally.

Have the cause of the fault in the
system remedied by a workshop.

Depending on version, 9 will
illuminate as an alternative if control
indicator r is not present. A
warning message may also be
displayed in the Driver Information
Centre 3 79.

Generic warning 9 3 73.
Ultrasonic parking assist 3 116.

Electronic Stability Program

x illuminates or flashes yellow.

Flashes

The system is actively engaged.
Engine output may be reduced and
the vehicle may be braked
automatically to a small degree.

Illuminates

A fault in the system is present.
Continued driving is possible. Driving
stability, however, may deteriorate
depending on road surface
conditions.

Have the cause of the fault remedied
by a workshop.

Electronic Stability Program (ESP)
3 114, Traction control system/Anti­Slip Regulator (ASR) 3 113.

Engine coolant temperature

$ illuminates red.
Illuminates for a few seconds after the

ignition is switched on.
If control indicator $ illuminates in

conjunction with a message in the
Driver Information Centre, the coolant
temperature is too high. Seek the
assistance of a workshop.

Driver Information Centre 3 79.

Caution

If engine coolant temperature is
too high, stop vehicle, switch off
the ignition. Danger to engine.
Check coolant level.

If the control indicator remains on,
seek the assistance of your
workshop.

Engine coolant temperature gauge
3 70.

Preheating

! illuminates yellow.
Preheating is activated. Only

activates when outside temperature
is low.

Diesel particle filter

[ illuminates yellow.
The diesel particle filter requires

cleaning.

Instruments and controls 77

Continue driving until
[ extinguishes. If possible, do not
allow engine speed to drop below
2000 rpm.

Illuminates

The diesel particle filter is full. Start
cleaning process as soon as
possible.

Diesel particle filter 3 106, Stop-start
system 3 103.

Engine oil pressure

I illuminates red.
Illuminates when the ignition is

switched on and extinguishes shortly
after the engine starts.

Illuminates when the engine is running

Caution

Engine lubrication may be
interrupted. This may result in
damage to the engine and/or
locking of the drive wheels.

1. Depress clutch.

2. Select neutral gear (or move
selector lever to N).

3. Move out of the flow of traffic as
quickly as possible without
impeding other vehicles.

4. Switch off ignition.

9 Warning

When the engine is off,
considerably more force is needed
to brake and steer. During an
Autostop the brake servo unit will
still be operational.

Do not remove key until vehicle is
stationary, otherwise the steering
wheel lock could engage
unexpectedly.

Check oil level before seeking the
assistance of a workshop 3 127.

Change engine oil

Diesel engines with diesel particle filter

I flashes red.
Illuminates when the ignition is

switched on and extinguishes shortly
after the engine starts.

The engine oil life monitor lets you
know when to change the oil. Control
indicator I will flash, together with a
message in the Driver Information
Centre, to indicate that engine oil life
has been diminished and the oil
needs changing.

Based on driving conditions, the
interval at which an oil change will be
indicated can vary considerably.

Depending on model variant, I may
flash in the following ways:

■ for 1 minute every 2 hours, or

■

for 3 minute cycles with I off for
intervals of 5 seconds.

78 Instruments and controls

The warning will be repeated every
time the engine is started, until the
engine oil is changed and the service
display is reset. Seek the assistance
of a workshop.

Service display 3 71.

Low engine oil level

y illuminates red.
Illuminates when the ignition is

switched on and extinguishes shortly
after the engine starts.

If the control indicator does not
extinguish after a few seconds, or if it
illuminates while driving, the engine
oil level is insufficient.

Check oil level before seeking the
assistance of a workshop 3 127.

Low fuel

$ illuminates or flashes yellow.
Illuminates for a few seconds after the

ignition is switched on.

Illuminates

Level in fuel tank is too low. Refuel
immediately 3 120.

Never run the tank dry.
Catalytic converter 3 107.

Flashes

Fault in fuel system.
Have the cause of the fault remedied

by a workshop.
Fuel gauge 3 69.

Drain fuel filter

z illuminates yellow.
Illuminates when the ignition is

switched on and goes out shortly after
the engine starts.

Illuminates when the engine is running

Indicates the presence of water in the
diesel. Seek the assistance of a
workshop immediately.

Immobiliser

d illuminates yellow.
Fault in the immobiliser system. The

engine cannot be started.

Stop-start system

Æ illuminates yellow.
A fault is present in the system.
Have the cause of the fault remedied

by a workshop.
Depending on version, 9 will

illuminate as an alternative if control
indicator Æ is not present. A warning
message may also be displayed in
the Driver Information Centre 3 79.

Generic warning 9 3 73.
Stop-start system 3 103.

Exterior light

8 illuminates green.
The exterior lights are on 3 88.

Exterior light failure

µ illuminates yellow.

Instruments and controls 79

One or more of the exterior lights is
faulty 3 132.

Depending on version, 9 will
illuminate as an alternative if control
indicator µ is not present. A warning
message may also be displayed in
the Driver Information Centre 3 79.

Generic warning 9 3 73.

High beam

C illuminates blue.
Illuminated when high beam is on and

during headlight flash 3 88.

Fog light

> illuminates green.
The front fog lights are on 3 90.

Rear fog light

r illuminates yellow.
The rear fog light is on 3 91.

Cruise control

m illuminates green.

The system is on.
Cruise control 3 115.

Door open

\ illuminates red.
A door or the tailgate is open.

Information displays

Driver Information Centre

The Driver Information Centre is
located in the instrument cluster
between the speedometer and
tachometer. Two versions are
available; a Standard version

80 Instruments and controls

and a Multifunction version with
further adjustable settings.

Some of the displayed functions differ
when the vehicle is being driven or at
a standstill. Some options are only
available when the vehicle is being
driven.

Depending on variant, the following
items appear in the display:

■ Odometer, trip odometer 3 68

■ Clock 3 64

■ Outside temperature 3 64

■ Headlight range adjustment
3 89

■ Transmission display 3 108

■ Stop-start system indicator 3 103

■ Vehicle messages 3 85

■ Trip computer 3 86

Selecting menus and options

The menus and options can be
selected via the buttons on the
instrument panel.

Press the SETq button:

■ once to access the settings menu

■ press again to access a menu
option and submenu options

■ after changes have been made,
briefly press again to confirm a
value and automatically return to
the previous display screen

Alternatively, press and hold the
SETq button to return to the
previous display screen without
saving changes to the current menu
option.

Note
The settings menu is exited
automatically after a delay. Only
changes already confirmed by
briefly pressing the SETq button
are stored.

Instruments and controls 81

Press the R button to scroll up the
screen and the menu options or to
increase the displayed value. Press
and hold to increase value rapidly
(press again to stop on the required
value).

Press the S button to scroll down the
screen and the menu options or to
decrease the displayed value. Press
and hold to decrease value rapidly
(press again to stop on the required
value).

Settings menu options ­Standard version

The settings menu contains the
following options:

■ ILLU

■ SPEEd

■ HOUR

■ UNIT

■ bUZZ

■ BAG P

■ DRL

ILLU (Brightness of interior lighting)
When driving at night with the low
beam on, adjust the brightness of the
vehicle's interior lighting (e.g.
instrument panel, climate control
display).

SPEEd (Speed limit warning chime)
Activate or deactivate the speed limit
warning chime or change the speed
limit. Speeds between 30 and
200 km/h can be stored.

When activated, the driver is alerted
with a warning chime when the set
speed limit is exceeded.

After accessing this menu option,
activate or deactivate the function
(set to On or Off) and confirm.

Press the SETq button when
activated (On) to access the current
set speed. Adjust as required and
confirm.

Warning chimes 3 85.

HOUR (Setting the clock)
Adjust the hours setting (flashing
value) and confirm. Adjust minutes
setting (flashing value) and confirm.

Clock 3 64.

UNIT (Unit of measurement)
Set the unit of measurement to km or
miles.

bUZZ (Warning chime volume)
Adjust the volume of warning chimes
and confirm. 8 volume levels are
available.

A chime is also sounded every time
the SETq, R or S button is pressed.

Warning chimes 3 85.

82 Instruments and controls

BAG P (Passenger front and side airbags activation/deactivation)

Activate the front passenger airbags
if an adult is occupying the front
passenger seat. Deactivate airbags
when a child restraint system is
installed on this seat.

9 Danger

Risk of fatal injury for a child using
a child restraint system on a seat
with activated front passenger
airbag.

Risk of fatal injury for an adult
person on a seat with deactivated
front passenger airbag.

After accessing this menu option,
activate or deactivate the airbags
(BAG P On or BAG P Off) and
confirm; a confirmation message
appears in the display. Select YES (to
confirm changes) or No (to cancel
changes).

Airbag deactivation 3 46.

DRL (Daytime running lights)
Activate the daytime running lights to
increase visibility of the vehicle during
daylight (set to On). Deactivate when
not required (set to Off).

Daytime running lights 3 89.

Settings menu options ­Multifunction version

The settings menu contains the
following options:

■ Lighting

■ Speed beep

■ Trip B data

■ Set time

■ Set date

■ Radio info

■ Autoclose

■ Unit of measurement

■ Language

■ Warning volume

■ Button volume

■ Seat belt buzzer

■ Service

■ Passenger airbag

■ Daytime running lights

■ Exit menu

LIGHTING (Brightness of interior lighting)

When driving at night with the low
beam on, adjust the brightness of the
vehicle's interior lighting (e.g.
instrument panel, climate control
display).

It is also possible to adjust the
brightness using the R or S buttons
without accessing the settings menu.

SPEED BEEP (Speed limit warning chime)

Activate or deactivate the speed limit
warning chime or change the speed
limit. Speeds between 30 and
200 km/h can be stored.

When activated, the driver is alerted
with a warning chime when the set
speed limit is exceeded.

After accessing this menu option,
activate or deactivate the function
(set to On or Off) and confirm.

Instruments and controls 83

Press the SETq button when
activated (On) to access the current
set speed. Adjust as required and
confirm.

Warning chimes 3 85.

TRIP B DATA
Activate or deactivate the second trip
computer (set to On or Off).

Trip B records average consumption,
distance travelled, average speed
and travel time (driving time). The
measurement can be restarted at any
time. Trip computer 3 86.

SET TIME (Setting the clock and clock mode)

After accessing this menu option, it is
possible to either set the time or
change the clock mode between 12
hour and 24 hour clock.

Select Time and confirm. Adjust the
hours setting (flashing value) and
confirm. Adjust minutes setting
(flashing value) and confirm.

Select Mode and confirm. Select
12h or 24h and confirm.

Clock 3 64.

SET DATE
Adjust the year setting (flashing
value) and confirm. Adjust month
setting (flashing value) and confirm.
Adjust the day setting (flashing value)
and confirm.

RADIO INFO (Display audio and radio information)

Activate radio info (set to On) to
display audio and radio information
(e.g. station frequency, RDS
messages, track number). Deactivate
when not required (set to Off).

AUTOCLOSE (Automatic central locking when driving)

Activate the autoclose feature (set to
On) to automatically lock the doors
when vehicle speed exceeds
20 km/h. Deactivate when not
required (set to Off).

UNIT OF MEASUREMENT (for Distance, Fuel consumption and Temperature)

After accessing this menu option, it is
possible to set the unit of
measurement for distance, fuel
consumption and temperature.

Select Distance and confirm. Set the
unit of measurement to km or mi
(miles) and confirm.

Select Consumption and confirm.
When the Distance unit is set to km, it
is possible to set the unit of
measurement for fuel consumption to
either l/100km or km/l. When the
Distance unit is set to mi (miles), fuel
consumption is shown in mpg.

Select Temperature and confirm. Set
the unit of measurement to °C or °F
and confirm.

LANGUAGE (for Display messages)
Display messages can be shown in
different languages, including:
English, German, French, Italian,
Portuguese, Spanish, Dutch, Polish
and Turkish. Select desired language
and confirm.

WARNING VOLUME (Warning chime volume)

Adjust the volume of warning chimes
and confirm. 8 volume levels are
available.

Warning chimes 3 85.

84 Instruments and controls

BUTTON VOLUME
A chime is sounded every time the
SETq, R or S button is pressed.

Adjust the volume of these chimes
and confirm. 8 volume levels are
available.

Warning chimes 3 85.

SEAT BELT BUZZER (Reactivate warning chime for driver and/or front passenger seat belt reminder)

This menu option is available only
when the seat belt reminder has
already been deactivated by a
workshop.

When reactivated, the driver and/or
front passenger are alerted with a
warning chime when the
corresponding seat belt is not
fastened.

Seat belt reminder 3 73.

SERVICE (Distance to next service)
Access this menu option to view the
remaining distance to the next
service.

The distance to next service is also
displayed automatically when the
distance reaches 2,000 km and is
repeated after every additional
200 km.

Service display 3 71.

PASSENGER AIRBAG (Passenger front and side airbags activation/ deactivation)

Activate the front passenger airbags
if an adult is occupying the front
passenger seat. Deactivate airbags
when a child restraint system is
installed on this seat.

9 Danger

Risk of fatal injury for a child using
a child restraint system on a seat
with activated front passenger
airbag.

Risk of fatal injury for an adult
person on a seat with deactivated
front passenger airbag.

After accessing this menu option,
activate or deactivate the airbags
(Bag Pass On or Bag Pass Off) and

confirm; a confirmation message
appears in the display. Select YES (to
confirm changes) or No (to cancel
changes).

Airbag deactivation 3 46.

DAYTIME RUNNING LIGHTS
Activate the daytime running lights to
increase visibility of the vehicle during
daylight (set to On). Deactivate when
not required (set to Off).

Daytime running lights 3 89.

EXIT MENU
Select this menu option to exit the
settings menu.

Instruments and controls 85

Vehicle messages

Warning chimes

Only one warning chime will sound at
a time.

The warning chime regarding
unfastened seat belts has priority
over any other warning chime.

When starting the engine or whilst driving

■ If seat belt is not fastened.

■ If a certain speed is exceeded with
the parking brake applied.

■ If the parking assist detects an
object.

■ If a fault is detected in the parking
assist.

■ If a door or the tailgate is not fully
closed when starting-off.

■ If the vehicle speed briefly exceeds
a set limit.

■ Vehicles with manual transmission
automated; neutral is not selected
or the foot brake has not been
depressed.

■ If a transmission fault is detected in
vehicles with manual transmission
automated.

■ If a warning message appears in
the Driver Information Centre.

When the vehicle is parked and/or the driver's door is opened

■ When the key is in the ignition
switch.

■ Vehicles with manual transmission
automated; neutral is not selected,
the parking brake is not applied, or
the foot brake and/or the
accelerator pedal has not been
depressed.

Fuel system messages

Fuel cut-off system

In the event of a collision of a certain
severity, the fuel system is cut-off and
the engine is switched off
automatically, for safety reasons. A
corresponding warning message may
also appear in the Driver Information
Centre 3 79.

To reset the fuel cut-off system and
enable the vehicle to be driven, refer
to "Vehicle shutdown" 3 103.

86 Instruments and controls

Trip computer

The trip computer provides
information on driving data, which is
continually recorded and evaluated
electronically.

The following functions can be
selected by pressing the TRIP button
repeatedly on the end of the wiper
lever:

Standard version

■ Average consumption

■ Instantaneous consumption

■ Range

■ Distance travelled

■ Average speed

■ Travel time (driving time)

Multifunction version

Two trip odometers, Trip A and Trip
B, are available for selection and are
recorded separately.

The information of the two trip
computers can be reset separately,
making it possible to display different
trip distances.

Trip A

■ Average consumption

■ Instantaneous consumption

■ Range

■ Distance travelled

■ Average speed

■ Travel time (driving time)

Trip B

■ Average consumption

■ Distance travelled

■ Average speed

■ Travel time (driving time)

Trip B can be deactivated via the
Driver Information Centre 3 79.

Reset trip computer information

To reset the trip computer, select one
of its functions, then press and hold
the TRIP button for a few seconds.

The following trip computer
information will be reset:

■ Average consumption

■ Distance travelled

■ Average speed

■ Travel time (driving time)

Instruments and controls 87

The trip computer will reset
automatically when the maximum
value of any of the parameters is
exceeded.

Average consumption

Average consumption is displayed,
taking into consideration the distance
travelled and the fuel used since the
last reset.

The measurement can be restarted at
any time.

Instantaneous consumption

Display of the instantaneous fuel
consumption.

_ _ _ _ will appear in the display if the
vehicle is left parked with the engine
running for a long time.

Range

The range is calculated from the
current contents of the fuel tank and
the average consumption since the
last reset.

When the range is less than 50 km,
_ _ _ _ will appear in the display.

After refuelling, the range is updated
automatically after a brief delay.

The measurement can be restarted at
any time.

Note
The range will not be displayed if the
vehicle is left parked with the engine
running for a long time.

Distance travelled

Displays the distance driven since the
last reset.

The measurement can be restarted at
any time.

Average speed

The average speed since the last
reset is displayed.

The measurement can be restarted at
any time.

Interruptions in the journey with the
ignition off are not included in the
calculations.

Travel time (driving time)

The time elapsed since the since the
last reset is displayed.

The measurement can be restarted at
any time.

Exit trip computer

To exit the trip computer, press and
hold the SETq button for more than
2 seconds.

Driver Information Centre 3 79.

Interruption of power supply

If the power supply has been
interrupted or if the battery voltage
has dropped too low, the values
stored in the trip computer will be lost.

88 Lighting

Lighting

Exterior lighting ............................ 88

Interior lighting ............................. 91

Lighting features .......................... 94

Exterior lighting

Light switch

Turn light switch:

= off / daytime running lights

§

= sidelights / headlights

9

Control indicator 8 3 78.

Tail lights

Tail lights are illuminated together
with headlights and sidelights.

High beam

To switch from low to high beam,
push lever.

To switch to low beam, pull lever.

Headlight flash

To activate the headlight flash, pull
lever.

Lighting 89

Headlight range adjustment

Manual headlight range adjustment

To adapt headlight range to the
vehicle load to prevent dazzling of
other road users: Press À or Á
buttons until the required setting is
displayed in the Driver Information
Centre 3 79.

0 = Front seats occupied
1 = All seats occupied

2 = All seats occupied and load

compartment laden

3 = Driver's seat occupied and load

compartment laden

Headlights when driving abroad

The asymmetrical headlight beam
extends visibility at the edge of the
road at the passenger side.

However, when driving in countries
where traffic drives on the opposite
side of the road, adjust the headlights
to prevent dazzling of oncoming
traffic.

Have the headlights adjusted by a
workshop.

Daytime running lights

Daytime running lights increase
visibility of the vehicle during daylight.

When the function is activated and
the ignition is switched on, the
headlights come on automatically and
instrument illumination is subdued.

The light switch must be in position

§. The daytime running lights switch
off when the ignition is switched off.

Note
The driver remains responsible for
switching on the low beam when
required, e.g. when driving through
a tunnel or at night.

When the function is deactivated, the
headlights do not come on
automatically when the ignition is
switched on and the light switch is in
position §.

The daytime running lights function is
activated/deactivated via a menu in
the Driver Information Centre 3 79.

90 Lighting

Hazard warning flashers

Operated with the ¨ button.

Turn and lane-change signals

Lever up = right turn signal
Lever down = left turn signal

If the lever is moved past the
resistance point, the turn signal is
switched on constantly. When the
steering wheel moves back, the turn
signal is automatically deactivated.

For five flashes, e.g. when changing
lanes, press the lever until resistance
is felt and then release.

Move the lever to the resistance point
and hold for longer indication.

Switch the indicator off manually by
moving the lever to its original
position.

Front fog lights

Operated by pressing the > button.
Switching on front fog lights will

switch sidelights on automatically.
Press the button again to turn the

front fog lights off.

Lighting 91

Rear fog lights

Operated by pressing the r button.
The rear fog light can only be

switched on when both the ignition
and headlights or sidelights (with front
fog lights) are on.

Press the button again to turn the rear
fog light off, or turn off the headlights
and/or the front fog lights.

Reversing lights

The reversing lights come on when
the ignition is on and reverse gear is
selected.

Misted light covers

The inside of the light covers may mist
up briefly in poor, wet and cold
weather conditions, in heavy rain or
after washing. The mist disappears
quickly by itself; to help, switch on the
headlights.

Interior lighting

Instrument panel illumination control

When driving at night with the
headlights on, adjust the brightness
of the vehicle's interior lighting
(including instrument panel, climate
control display etc.) via the settings
menu of the Driver Information Centre
3 79.

To adjust brightness:

Standard version of Driver Information Centre

1. Press the SETq button once to
access the settings menu.

2. Scroll through the menu options
using the R or S buttons until
menu option ILLU appears in the
display.

92 Lighting

3. Press the R or S button to
increase or decrease the
displayed value.

4. Press SETq briefly to confirm
changes and automatically return
to the previous display screen.

Multifunction version of Driver Information Centre

1. Press the SETq button to access
the settings menu.

2. Scroll through the menu options
using the R or S buttons until
menu option LIGHTING appears
in the display.

3. Press the R or S button to
increase or decrease the
displayed value.

4. Press SETq briefly to confirm
changes and automatically return
to the previous display screen.

It is also possible to adjust the
brightness using the R or S buttons
without accessing the settings menu.

Driver Information Centre 3 79.

Interior lights

Depending on model variant, during
entry and exit of the vehicle the front
and rear courtesy lights come on
automatically and then switch off after
a delay.

Note
In the event of an accident of a
certain severity, the interior lights
come on automatically. Fuel cut-off
system 3 85.

Front courtesy light

Centre switch position: automatic
interior light.

To operate manually when the doors
are closed, press the lens on either
side.

Front courtesy light with reading lights

Centre switch position: automatic
interior light.

Can be operated individually or
together with the 7 switch when the
doors are closed.

Press rocker switch 7 left or right to
operate respective reading light.

Lighting 93

Rear courtesy lights

Centre switch position: automatic
interior light.

To operate manually when the doors
are closed, press the lens on either
side.

Load compartment lighting

Depending on model variant, load
compartment lighting switches on
when the rear doors / tailgate or
sliding side door is opened.

Removable rear courtesy light

Depending on model variant, the
removable rear courtesy light may
illuminate when the rear doors /
tailgate or sliding side doors are
opened and the central switch is in the
middle position.

Switch the light on permanently by
pressing the top part of the central
switch c.

Switch the light off permanently by
pressing the bottom part of the central
switch (AUTO OFF).

To use as a handheld torch, press the
button at the top of the lamp assembly
(see illustration) to release it and pull
torch down gently to remove. Press
the switch on the end of the torch to
turn the light on/off.

Replace the torch in its original
position to recharge the battery after
use.

94 Lighting

Lighting features

Battery discharge protection

To ensure reliable engine restarts,
several battery discharge protection
features are implemented as part of
the stop-start system.

Stop-start system 3 103.

Climate control 95

Climate control

Climate control systems ............... 95

Air vents ....................................... 99

Maintenance .............................. 100

Climate control systems

Heating and ventilation system

Controls for:

■ Temperature

■ Fan speed

■ Air distribution
Heated rear window Ü 3 32.

Temperature

red = warm
blue = cold

Heating will not be fully effective until
the engine has reached normal
operating temperature.

Fan speed

Adjust the air flow by switching the fan
to the desired speed.

Air distribution

= to head area

M

= to head area and foot well

L

= to foot well

K

= to windscreen, front door

J

windows and foot well

= to windscreen and front door

V

windows

Intermediate settings are possible.

Demisting and defrosting the windows

■ Set temperature control to warmest
level.

■ Set fan speed to highest level.

■

Set air distribution control to V.

■

Switch on heated rear window Ü.

96 Climate control

■ Open side air vents as required and
direct them towards door windows.

■ For simultaneous warming of the
foot well, set air distribution control
to J.

Air conditioning system

Additional to the heating and
ventilation system, the air
conditioning system has controls for:

= cooling

n

= air recirculation

4

Heated front seats ß 3 36.

Cooling n

Press button n to switch on cooling.
Activation is indicated by the LED in
the button. Cooling is only functional
when the engine is running and
climate control fan is switched on.

Press button n again to switch off
cooling.

The air conditioning system cools and
dehumidifies (dries) the air when
outside temperature is above a
specific level. Therefore
condensation may form and drip from
under the vehicle.

If no cooling or drying is required,
switch the cooling system off to save
fuel.

Air recirculation system

Press button 4 to activate air
recirculation mode. Activation is
indicated by the LED in the button.

Press button 4 again to deactivate
air recirculation mode.

9 Warning

The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up. The quality
of the passenger compartment air
deteriorates, which may cause the
vehicle occupants to feel drowsy.

In warm and very humid ambient air
conditions, the windscreen may mist
up from outside, when cold air is
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and deactivate V.

Maximum cooling

Briefly open the windows so that hot
air can disperse quickly.

■

Cooling n on.

■

Air recirculation system 4 on.

■

Set air distribution control to M.

■ Set temperature control to coldest
level.

Climate control 97

■ Set fan speed to highest level.

■ Open all air vents.

Demisting and defrosting the windows

■ Set temperature control to warmest
level.

■ Set fan speed to highest level.

■

Set air distribution control to V.

■

Switch cooling n on.

■

Switch on heated rear window Ü.

■ Open side air vents as required and
direct them towards door windows.

■ For simultaneous warming of the
foot well, set air distribution control
to J.

Electronic climate control system

Controls for:

■ Temperature

■ Air distribution and menu selection

■ Fan speed
AUTO = Automatic mode

4

Ê

OFF = switch on/off

Heated rear window Ü 3 32.

= air recirculation
= demisting and defrosting

The preselected temperature is
automatically regulated. In the
automatic mode the fan speed and air
distribution automatically regulate the
air flow.

The system can be manually adapted
by use of air distribution and air flow
controls.

The electronic climate control system
is only fully operational when the
engine is running.

For correct operation do not cover the
sensor on the instrument panel.

Automatic mode

Basic setting for maximum comfort:

■ Press AUTO button.

■ Open all air vents.

■

n on.

■ Set desired temperature.

Temperature preselection

Temperatures can be set to the
desired value.

For reasons of comfort, change
temperature only in small increments.
Turn AUTO knob to adjust.

98 Climate control

clockwise = warm
anticlockwise = cold

Heating will not be fully effective until
the engine has reached normal
operating temperature.

When the minimum temperature is
set below 16 ℃, the electronic climate
control system runs at maximum
cooling. LO appears in the display.

If the maximum temperature is set
above 32 ℃, the electronic climate
control system runs at maximum
heating. HI appears in the display.

Fan speed

The selected fan speed is indicated
with bars in the display.

Press ] or < to increase or decrease
the fan speed.

maximum fan
speed
minimum fan
speed

Press n button to deactivate fan.
To return to automatic fan speed:

Press AUTO button.

= all bars displayed

= one bar displayed

Demisting and defrosting the windows

Press the Ê button.
Temperature and air distribution are

set automatically and the fan runs at
a high speed.

When the vehicle reaches normal
operating temperature the function
remains active for approx. 3 minutes.

To return to automatic mode: press
button n or AUTO.

Air distribution

Press R, S and 6 buttons.
LED in buttons illuminate.
Arrows shown in the display indicate

the distribution settings.

Cooling

Press button n to switch on cooling.
Activation is indicated by the LED in
the button. Cooling is only functional
when the engine is running and
climate control fan is switched on.

Press button n again to switch off
cooling.

The air conditioning system cools and
dehumidifies (dries) when outside
temperature is above a specific level.
Therefore condensation may form
and drip from under the vehicle.

If no cooling or drying is required
press n again to switch the cooling
system off, thus saving fuel.

Manual air recirculation mode

Operated with the 4 button.
recirculationon= LED in button

illuminated; D
appears in the

display
recirculation
off

= LED in button

extinguishes; E

appears in the

display

9 Warning

The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up. The quality