查询MC100EL58DR2供应商
MC10EL58, MC100EL58
5.0 VECL 2:1 Multiplexer
Description
The MC10EL/100EL58 is a 2:1 multiplexer. The device is
functionally equivalent to the E158 device with higher performance
capabilities. With propagation delays and output transition times
significantly faster than the E158, the EL58 is ideally suited for those
applications which require the ultimate in AC performance.
The 100 Series contains temperature compensation.
Features
• 230 ps Propagation Delay
• PECL Mode Operating Range: V
• NECL Mode Operating Range: V
−5.7 V
• Internal Input Pulldown Resistors on D
• Pb−Free Packages are Available
1
NC
= 4.2 V to 5.7 V with VEE = 0 V
CC
= 0 V with VEE = −4.2 V to
CC
, Db, and SEL
a
V
CC
8
1
SOIC−8
D SUFFIX
CASE 751
8
1
TSSOP−8
DT SUFFIX
CASE 948R
http://onsemi.com
MARKING
DIAGRAMS*
8
HEL58
ALYW
G
1
8
HL58
ALYWG
G
1
8
KEL58
ALYW
G
1
8
KL58
ALYWG
G
1
2
D
a
3
45
SEL
1
MUX
0
78Q
6
QDb
V
EE
Figure 1. Logic Diagram and Pin Assignment
G
4Z M G
14
DFN8
MN SUFFIX
CASE 506AA
H = MC10
K = MC100
4Z = MC10
2O = MC100
A = Assembly Location
(Note: Microdot may be in either location)
*For additional marking information, refer to
Application Note AND8002/D.
L = Wafer Lot
Y = Year
W = Work Week
M
= Date Code
G = Pb−Free Package
G
2O M G
14
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 6 of this data sheet.
© Semiconductor Components Industries, LLC, 2006
December, 2006 − Rev. 7
1 Publication Order Number:
MC10EL58/D
MC10EL58, MC100EL58
Table 1. PIN DESCRIPTION
PIN FUNCTION
D
, Db ECL Data Inputs
a
Q, Q
SEL ECL Select Input
V
CC
V
EE
NC No Connect
EP
ECL Data Outputs
Positive Supply
Negative Supply
Exposed pad must be connected to a sufficient thermal
conduit. Electrically connect to the most negative supply or
leave floating open.
Table 2. FUNCTION TABLE
SEL*
H
L
* Pin will default low when left open.
Data
a
b
Table 3. ATTRIBUTES
Characteristics Value
Internal Input Pulldown Resistor
Internal Input Pullup Resistor N/A
ESD Protection Human Body Model
Machine Model
Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) Level 1
Flammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in
Transistor Count 45
Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
1. Refer to Application Note AND8003/D for additional information.
75 kW
> 1 kV
> 100 V
http://onsemi.com
2
MC10EL58, MC100EL58
Table 4. MAXIMUM RATINGS
Symbol Parameter Condition 1 Condition 2 Rating Unit
V
CC
V
EE
V
I
I
out
T
A
T
stg
q
JA
q
JC
q
JA
q
JC
q
JA
T
sol
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
PECL Mode Power Supply VEE = 0 V 8 V
NECL Mode Power Supply VCC = 0 V −8 V
PECL Mode Input Voltage
NECL Mode Input Voltage
Output Current Continuous
VEE = 0 V
V
= 0 V
CC
Surge
VI V
VI V
CC
EE
6
−6
50
100
V
V
mA
mA
Operating Temperature Range −40 to +85 °C
Storage Temperature Range −65 to +150 °C
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
SOIC−8
SOIC−8
190
130
°C/W
°C/W
Thermal Resistance (Junction−to−Case) SOIC−8 41 to 44 °C/W
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
TSSOP−8
TSSOP−8
185
140
°C/W
°C/W
Thermal Resistance (Junction−to−Case) Standard Board TSSOP−8 41 to 44 °C/W
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
Wave Solder Pb
Pb−Free
<2 to 3 sec @ 248°C
<2 to 3 sec @ 260°C
DFN8
DFN8
129
84
265
265
°C/W
°C/W
°C
Table 5. 10EL SERIES PECL DC CHARACTERISTICS V
= 5.0 V; VEE= 0.0 V (Note 2)
CC
−40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
V
OH
V
OL
V
IH
V
IL
I
IH
I
IL
Power Supply Current 14 17 14 17 14 17 mA
Output HIGH Voltage (Note 3) 3920 4010 4110 4020 4105 4190 4090 4185 4280 mV
Output LOW Voltage (Note 3) 3050 3200 3350 3050 3210 3370 3050 3227 3405 mV
Input HIGH Voltage 3770 4110 3870 4190 3940 4280 mV
Input LOW Voltage 3050 3500 3050 3520 3050 3555 mV
Input HIGH Current 150 150 150
Input LOW Current 0.5 0.5 0.3
mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with V
3. Outputs are terminated through a 50 ohm resistor to V
. VEE can vary +0.06 V / −0.5 V.
CC
−2 volts.
CC
http://onsemi.com
3
MC10EL58, MC100EL58
Table 6. 10EL SERIES NECL DC CHARACTERISTICS V
= 0.0 V; VEE= −5.0 V (Note 4)
CC
−40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
V
OH
V
OL
V
IH
V
IL
I
IH
I
IL
Power Supply Current 14 17 14 17 14 17 mA
Output HIGH Voltage (Note 5) −1080 −990 −890 −980 −895 −810 −910 −815 −720 mV
Output LOW Voltage (Note 5) −1950 −1800 −1650 −1950 −1790 −1630 −1950 −1773 −1595 mV
Input HIGH Voltage −1230 −890 −1130 −810 −1060 −720 mV
Input LOW Voltage −1950 −1500 −1950 −1480 −1950 −1445 mV
Input HIGH Current 150 150 150
Input LOW Current 0.5 0.5 0.3
mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
4. Input and output parameters vary 1:1 with V
5. Outputs are terminated through a 50 ohm resistor to V
Table 7. 100EL SERIES PECL DC CHARACTERISTICS V
. VEE can vary +0.06 V / −0.5 V.
CC
−2 volts.
CC
= 5.0 V; VEE= 0.0 V (Note 6)
CC
−40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Ty p Max Min Typ Max Unit
I
EE
V
OH
V
OL
V
IH
V
IL
I
IH
I
IL
Power Supply Current 14 17 14 17 16 19 mA
Output HIGH Voltage (Note 7) 3915 3995 4120 3975 4045 4120 3975 4050 4120 mV
Output LOW Voltage (Note 7) 3170 3305 3445 3190 3295 3380 3190 3295 3380 mV
Input HIGH Voltage 3835 4120 3835 4120 3835 4120 mV
Input LOW Voltage 3190 3525 3190 3525 3190 3525 mV
Input HIGH Current 150 150 150
Input LOW Current 0.5 0.5 0.5
mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
6. Input and output parameters vary 1:1 with V
7. Outputs are terminated through a 50 ohm resistor to V
. VEE can vary +0.8 V / −0.5 V.
CC
−2 volts.
CC
http://onsemi.com
4
MC10EL58, MC100EL58
Table 8. 100EL SERIES NECL DC CHARACTERISTICS V
= 0.0 V; VEE= −5.0 V (Note 8)
CC
−40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Ty p Max Min Typ Max Unit
I
EE
V
OH
V
OL
V
IH
V
IL
I
IH
I
IL
Power Supply Current 14 17 14 17 16 19 mA
Output HIGH Voltage (Note 9) −1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
Output LOW Voltage (Note 9) −1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
Input HIGH Voltage −1165 −880 −1165 −880 −1165 −880 mV
Input LOW Voltage −1810 −1475 −1810 −1475 −1810 −1475 mV
Input HIGH Current 150 150 150
Input LOW Current 0.5 0.5 0.5
mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
8. Input and output parameters vary 1:1 with V
9. Outputs are terminated through a 50 ohm resistor to V
Table 9. AC CHARACTERISTICS V
CC
. VEE can vary +0.8 V / −0.5 V.
CC
−2 volts.
CC
= 5.0 V; VEE= 0.0 V or VCC= 0.0 V; VEE= −5.0 V (Note 10)
−40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Ty p Max Min Typ Max Unit
f
max
t
PLH
t
PHL
t
JITTER
t
r
t
f
Maximum Toggle Frequency 1.5 GHz
Propagation Delay to Output
D to Q
SEL to Q
6090220
250
380
410
120
150
230
260
340
370
140
170
250
280
360
390
ps
Random Clock Jitter (RMS) 0.9 ps
Output Rise/Fall Times Q
100 225 350 100 225 350 100 225 350 ps
(20% − 80%)
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
10.10 Series: V
100 Series: V
can vary +0.06 V / −0.5 V.
EE
can vary +0.8 V / −0.5 V.
EE
Zo = 50 W
Zo = 50 W
Receiver
Device
Driver
Device
QD
Q D
50 W 50 W
V
VTT = VCC − 3.0 V
TT
Figure 2. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D − Termination of ECL Logic Devices.)
http://onsemi.com
5
MC10EL58, MC100EL58
ORDERING INFORMATION
Device Package Shipping
MC10EL58D SOIC−8 98 Units / Rail
MC10EL58DG SOIC−8
(Pb−Free)
MC10EL58DR2 SOIC−8 2500 / Tape & Reel
MC10EL58DR2G SOIC−8
(Pb−Free)
MC10EL58DT TSSOP−8 100 Units / Rail
MC10EL58DTG TSSOP−8
(Pb−Free)
MC10EL58DTR2 TSSOP−8 2500 / Tape & Reel
MC10EL58DTR2G TSSOP−8
(Pb−Free)
MC10EL58MNR4 DFN8 1000 / Tape & Reel
MC10EL58MNR4G DFN8
(Pb−Free)
MC100EL58D SOIC−8 98 Units / Rail
MC100EL58DG SOIC−8
(Pb−Free)
MC100EL58DR2 SOIC−8 2500 / Tape & Reel
MC100EL58DR2G SOIC−8
(Pb−Free)
MC100EL58DT TSSOP−8 100 Units / Rail
MC100EL58DTG TSSOP−8
(Pb−Free)
MC100EL58DTR2 TSSOP−8 2500 / Tape & Reel
MC100EL58DTR2G TSSOP−8
(Pb−Free)
MC100EL58MNR4 DFN8 1000 / Tape & Reel
MC100EL58MNR4G DFN8
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
98 Units / Rail
2500 / Tape & Reel
100 Units / Rail
2500 / Tape & Reel
1000 / Tape & Reel
98 Units / Rail
2500 / Tape & Reel
100 Units / Rail
2500 / Tape & Reel
1000 / Tape & Reel
†
Resource Reference of Application Notes
AN1405/D − ECL Clock Distribution Techniques
AN1406/D − Designing with PECL (ECL at +5.0 V)
AN1503/D −
AN1504/D − Metastability and the ECLinPS Family
AN1568/D − Interfacing Between LVDS and ECL
AN1672/D − The ECL Translator Guide
AND8001/D − Odd Number Counters Design
AND8002/D − Marking and Date Codes
AND8020/D − Termination of ECL Logic Devices
AND8066/D − Interfacing with ECLinPS
AND8090/D − AC Characteristics of ECL Devices
ECLinPSt I/O SPiCE Modeling Kit
http://onsemi.com
6
−Y−
−Z−
MC10EL58, MC100EL58
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AH
NOTES:
−X−
A
58
B
1
S
0.25 (0.010)
4
M
M
Y
K
G
C
SEATING
PLANE
0.10 (0.004)
H
D
0.25 (0.010) Z
M
Y
SXS
N
X 45
_
M
J
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
MILLIMETERS
DIMAMIN MAX MIN MAX
4.80 5.00 0.189 0.197
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.053 0.069
D 0.33 0.51 0.013 0.020
G 1.27 BSC 0.050 BSC
H 0.10 0.25 0.004 0.010
J 0.19 0.25 0.007 0.010
K 0.40 1.27 0.016 0.050
M 0 8 0 8
____
N 0.25 0.50 0.010 0.020
S 5.80 6.20 0.228 0.244
INCHES
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
0.6
0.024
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
4.0
0.155
1.270
0.050
SCALE 6:1
ǒ
inches
mm
Ǔ
http://onsemi.com
7
MC10EL58, MC100EL58
PACKAGE DIMENSIONS
TSSOP−8
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948R−02
ISSUE A
0.10 (0.004)
−T−
SEATING
PLANE
8x REFK
S
U0.15 (0.006) T
2X L/2
85
L
PIN 1
IDENT
S
U0.15 (0.006) T
0.10 (0.004) V
1
4
A
M
B
−U−
−V−
S
U
T
S
0.25 (0.010)
M
F
DETAIL E
C
D
G
DETAIL E
−W−
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH
OR GATE BURRS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
5. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
6. DIMENSION A AND B ARE TO BE DETERMINED
AT DATUM PLANE −W−.
DIM MIN MAX MIN MAX
A 2.90 3.10 0.114 0.122
B 2.90 3.10 0.114 0.122
C 0.80 1.10 0.031 0.043
D 0.05 0.15 0.002 0.006
F 0.40 0.70 0.016 0.028
G 0.65 BSC 0.026 BSC
K 0.25 0.40 0.010 0.016
L 4.90 BSC 0.193 BSC
M 0 6 0 6
____
INCHESMILLIMETERS
http://onsemi.com
8
MC10EL58, MC100EL58
PACKAGE DIMENSIONS
DFN8
CASE 506AA−01
ISSUE D
8 X
REFERENCE
2 X
SEATING
PLANE
PIN ONE
2 X
C0.10
C0.08
C0.10
A1
8 X
D
A
B
E
C0.10
TOP VIEW
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994 .
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
MILLIMETERS
DIM MIN MAX
A 0.80 1.00
A1 0.00 0.05
A3 0.20 REF
b 0.20 0.30
D 2.00 BSC
D2 1.10 1.30
E 2.00 BSC
E2 0.70 0.90
e 0.50 BSC
K 0.20 −−−
L 0.25 0.35
A
SIDE VIEW
(A3)
C
D2
e/2
1
e
4
L
E2
K
8
5
8 X
0.10 C
b
0.05 C
A
BB
NOTE 3
BOTTOM VIEW
ECLinPS is a trademark of Semiconductor Components INdustries, LLC (SCILLC).
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC10EL58/D
9
Loading...