Onkyo TX-SR601, TX-SR601E, TX-SR701, TX-SR701E Instruction Manual

AV Receiver

TX-SR701/701E TX-SR601/601E

Instruction Manual

Contents

Before using 2

Facilities and connections 8

Thank you for purchasing the Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.

Setup and operation 31

Remote controller 63

Appendix 75

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safety Instructions

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

OUVRIR

NE PAS

1. Read Instructions – All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions – The safety and operating instructions should be retained for future reference.

3. Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions should be followed.

5. Water and Moisture – Do not use the appliance near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

6. Cleaning – Unplug the appliance from the wall outlet before cleaning. The appliance should be cleaned with a dry cloth or only as recommended by the manufacturer.

7. Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the appliance and to protect it from overheating, and these openings must not be blocked or covered. Do not use the appliance on a bed, sofa, rug, or other such surface. Newspapers, table clothes, curtains, and other items can inadvertently block ventilation slots. Do not place the unit near curtains that could obstruct the ventilation. If you install the appliance in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the appliance should be set 10 cm (4") away from the rear panel or wall, creating a ﬂue-like gap for warm air to escape.

8. Heat – The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including ampliﬁer) that produce heat.

9. Grounding or Polarization – The appliance may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will ﬁt into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to ﬁt, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized or grounding-type plug. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

11. Attachments – Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. Accessories – Do not place the appliance on an unstable cart, stand, tripod, bracket, or table. The appliance may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the appliance. Any mounting of the appliance should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

12. An appliance and cart combination should be moved with care to avoid injury from tip-over. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

13. Lightning – For added protection for the appliance during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the appliance due to lightning and power-line surges.

14. Servicing – Do not attempt to service the appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualiﬁed service personnel.

Damage Requiring Service – Unplug the appliance form the wall outlet and refer servicing to qualiﬁed service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen into the

appliance, C. If the appliance has been exposed to rain or water, D. If the appliance does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualiﬁed technician to

restore the appliance to its normal operation, E. If the appliance has been dropped or damaged in any way,

and F. When the appliance exhibits a distinct change in performance

– this indicates a need for service.

15. Object and Liquid Entry – Never push objects of any kind into the appliance through openings as they may touch dangerous voltage points or short-out parts that could result in a ﬁre or electric shock. The appliance should not be exposed to dripping or splashing and no objects ﬁlled with liquids, such as vases should be placed on the appliance. Don’t put candles or other burning objects on top of this unit.

16. Batteries – Always consider the environmental issues and follow local regulations when disposing of batteries.

PORTABLE CART WARNING

S3125A

Precautions

1. Recording Copyright

Recording of copyrighted material for other than personal use is illegal without permission of the copyright holder.

2. AC Fuse

The fuse is located inside the chassis and is not user-serviceable. If power does not come on, contact your Onkyo authorized service station.

3. Care

From time to time you should wipe the front and rear panels and the cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a weak solution of mild detergent and water, wring it out dry, and wipe off the dirt. Following this, dry immediately with a clean cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since these could damage the ﬁnish or remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.

Worldwide models are equipped with a voltage selector to conform to local power supplies. Be sure to set this switch to match the voltage of the power supply in your area before plugging in the unit.

For British models

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualiﬁed service personnel.

IMPORTANT

The wires in the mains lead are colored in accordance with the following code:

Blue : Neutral

Brown : Live As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying the terminals in your plug, proceed as follows: The wire which is colored blue must be connected to the terminal which is marked with the letter N or colored black. The wire which is colored brown must be connected to the terminal which is marked with the letter L or colored red.

IMPORTANT

A 5 ampere fuse is ﬁtted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amperes and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMPERE SOCKET. If in any doubt, consult a qualiﬁed electrician.

For U.S. models Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, speciﬁes that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

FCC INFORMATION FOR USER

CAUTION:

The user changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian models

NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES

WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE LA

CLASSE B EST CON-FORME À LA NORME NMB-003 DU CANADA.

Sur les modèles dont la ﬁche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Contents

Before using

Important Safety Instructions ........................... 2

Precautions ......................................................... 3

Contents .............................................................. 4

Features .............................................................. 6

Supplied accessories ........................................ 7

Before using this unit ........................................ 7

Setting the voltage selector (Worldwide models only) ......7

Installing the remote controller batteries .......................... 7

Using the remote controller ..............................................7

Facilities and connections

Front panel facilities .......................................... 8

Front panel ...................................................................... 8

Front panel display ....................................................... 11

Remote controller ............................................ 12

Connections ..................................................... 14

TX-SR701/701E ............................................................ 15

TX-SR601/601E ............................................................ 15

Connecting your audio components ............................... 16

Connecting your video components ............................... 17

12V TRIGGER ZONE 2 terminal .................................. 21

PRE OUT (TX-SR701/701E only) ................................. 21

Operating components not reached by the

remote controller signals (IR IN) ................ 22

If the remote controller signal does not reach

the TX-SR701/701E/601/601E remote sensor ........ 22

Connecting the remote zone (Zone 2) speakers ...23

When using the ZONE 2 SPEAKERS terminals ............ 23

When using the ZONE 2 LINE OUT terminals ............. 23

When using the ZONE 2 PRE OUT terminals

(TX-SR701/701E only)............................................ 23

Connections ..................................................... 24

AC OUTLETS ................................................................ 24

REMOTE CONTROL .............................................. 24

Connecting speakers ....................................... 25

Standard speaker setup for surround sound .................... 25

Minimum speaker conﬁguration for surround sound

playback .................................................................. 25

Speaker placement .......................................................... 25

Using the speaker cable labels ........................................ 26

Connecting a subwoofer .................................................26

Connecting the surround back speakers

(TX-SR701/701E only) ........................................... 26

Connecting speakers ....................................................... 27

Connecting the speaker cable ......................................... 27

Connecting the power .................................... 28

Connecting a subwoofer .................................................28

Turning on the power ...................................................... 28

Turning on the power from the remote controller ..........28

Connecting antennas ....................................... 29

Assembling the AM loop antenna ...................................29

Connecting the AM antenna cable ..................................29

Connecting the included antennas ...................................29

Connecting an FM outdoor antenna ................................30

Connecting an AM outdoor antenna ................................30

Directional linkage ..........................................................30

Connecting the antenna cable to the 75/300 Ω antenna

adapter (For all models other than USA & Canadian

models and European models) .................................30

Setup and operation

Conﬁguring the speakers ................................ 31

Displaying the Main Menu ..............................................31

Speaker Conﬁguration .....................................................31

Setting the speaker distance from your normal listening

position ....................................................................33

Calibrating the speaker levels ..........................................34

Buttons used for navigating through the menus ..............36

Listening to Radio Broadcasts ....................... 37

Tuning into a radio station ...............................................37

Listening to a stereo radio station (FM mode) ................37

Presetting a radio station .................................................38

Selecting a preset radio station ........................................38

Erasing a preset radio station ..........................................38

Listening to RDS broadcasts

(European models only) ............................. 39

Listening to RDS broadcasts ...........................................39

PTY program types in Europe .........................................39

Displaying Radio Text (RT) ............................................40

Performing a PTY scan ...................................................40

Performing a TP scan ......................................................40

Selecting an Audio Component ...................... 41

Basic operation ................................................................41

Selecting the type of audio input signal ..........................42

Temporarily changing the speaker output levels .............43

To change the display of the input source

from TAPE to MD ...................................................43

Using the sleep time (remote controller only) .................44

Listening with headphones ..............................................44

Enjoying DVD multichannel audio playback ..................44

Switching the display ......................................................45

Temporarily turning off the sound ...................................45

Listening Modes ............................................... 46

Selecting a listening mode (TX-SR701/701E) ................48

Re-EQ function for movies (TX-SR701/701E only) ......49

Selecting a listening mode (TX-SR601/601E) ................50

Original ﬁlter (CinemaFILTER) loading for movies

(TX-SR601/601E only) ...........................................51

Input Setup ........................................................ 52

Hardware Setup ................................................ 55

Hardware Conﬁg .............................................................55

Contents

Preference .........................................................56

Preference ........................................................................56

Audio Adjust ......................................................57

Enjoying music in the remote zone .................60

Using the buttons .............................................................60

Using the remote controller .............................................60

Adjusting the volume for the remote zone ......................60

Recording ..........................................................61

Recording the input source (REC OUT selector) ...........61

Recording both the audio and video ...............................62

Remote controller

Using remote controller ...................................63

Overview ........................................................................63

Calling up a preset radio station ...................................... 63

Controlling an Onkyo cassette tape deck ........................63

Controlling an Onkyo DVD player .................................64

Controlling an Onkyo CD player ....................................65

Controlling an Onkyo MD recorder ................................66

Entering a pre-programming code ..................67

Learning a pre-programming code .................................. 67

Pre-programming codes .................................................. 68

Operating your programmed

remote controller .........................................69

DVD MODE (DVD Player Mode) .................................. 69

SAT MODE (Satellite Tuner Mode) ...............................69

CABLE MODE (Cable Mode) .......................................69

VCR MODE (VCR Mode) .............................................70

TV MODE (TV Mode) ...................................................70

Programming the commands of remote

controllers for other devices into the

remote controller .........................................71

Programming procedure .................................................. 71

Erasing the programmed command from one button ......72

Erasing all the commands programmed under a MODE

button .......................................................................72

Using the macro function .................................73

What is the macro function? ........................................ 73

Programming the macro ..................................................73

Executing the macro ........................................................73

Erasing a macro from the MACRO 1 (or 2) button .........74

Erasing all commands and macros that have been

programmed .............................................................74

Appendix

Troubleshooting guide ......................................75

POWER .......................................................................... 75

SPEAKERS .................................................................... 75

FM/AM TUNER ............................................................. 75

VIDEO and AUDIO ........................................................ 76

REMOTE CONTROLLER ............................................. 76

OTHER ........................................................................... 76

If one of the messages shown below appears ................. 77

Speciﬁcations (TX-SR701/701E) ......................78

Speciﬁcations (TX-SR601/601E) ......................79

Declaration of Conformity

We,

ONKYO EUROPE ELECTRONICS GmbH INDUSTRIESTRASSE 20 82110 GERMERING, GERMANY

declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3.

GERMERING, GERMANY

I. MORI

ONKYO EUROPE ELECTRONICS GmbH

Features

TX-SR701/701E

Ampliﬁer Features

■ 100 W × 2 (Front)/ 100 W (Center)/ 100 W × 2 (Surround)/ 100 W (Surround Back) at 8 ohms, 20 Hz - 20 kHz, 0.08 % THD (FTC rated)

■ 130 W × 2 (Front)/ 130 W (Center)/ 130 W × 2 (Surround)/ 130 W (Surround Back) at 6 ohms, 1 kHz (DIN)

■ 160 W × 2 (Front)/ 160 W (Center)/ 160W × 2 (Surround)/ 160 W (Surround Back) at 6 ohms, 1 kHz (JEITA)

■ Wide Range Ampliﬁer Technology (WRAT)

■ Powered Zone 2 Capability

■ State-of-the-art linear PCM 192 kHz/24-bit DACs for

All channels

■ Optimum gain volume circuitry

■ VLSC (Vector Linear Shaping Circuitry) for L/C/R

Channels

Audio/Video Features

■ THX® Select certiﬁed

■ THX surround EX

■ Dolby®* Digital, Dolby Digital EX, Dolby Pro Logic II

■ DTS, DTS 96/24, DTS-ES Extended Surround, DTS

Neo:6

■ Non-Scaling Conﬁguration

■ Re-EQ

■ Pure Audio Mode

■ Crossover Adjustment (40/60/80/100/120/150 Hz)

■ Onscreen graphical displays

■ Digital Outputs (1 coaxial, 1 optical)

■ 2 component video inputs and 1 output

■ 3 Assignable digital inputs (1 coaxial, 2 optical)

■ 5 S-Video inputs and 3 outputs

■ Front panel A/V, S-Video, Optical inputs

■ Multi channel input for DVD-Audio and Super Audio

■ Rec out selector and Zone 2 selector

■ Pre-out terminals for Front L/R, Center, Surround L/

R, Surround Back L/R, Subwoofer and Zone 2 L/R

■ Color-coded speaker terminals

TX-SR601/601E

Ampliﬁer Features

■ 85 W × 2 (Front)/ 85 W (Center)/ 85 W × 2 (Surround)/ 85 W

(Surround Back) at 8 ohms, 20 Hz - 20 kHz, 0.08 % THD (FTC rated)

■ 120 W × 2 (Front)/ 120 W (Center)/ 120 W × 2 (Surround)/

120 W (Surround Back) at 6 ohms, 1 kHz (DIN)

■ 150 W × 2 (Front)/ 150 W (Center)/ 150 W × 2 (Surround)/ 150

W (Surround Back) at 6 ohms, 1 kHz (JEITA)

■ Wide Range Ampliﬁer Technology (WRAT)

■ Powered Zone 2 Capability

■ State-of-the-art linear PCM 192 kHz/24-bit DACs for

All channels

■ Optimum gain volume circuitry

■ VLSC (Vector Linear Shaping Circuitry) (except for

USA & Canadian models, Australian models)

Audio/Video Features

■ Dolby Digital, Dolby Digital EX, Dolby Pro Logic II

■ DTS, DTS 96/24, DTS-ES Extended Surround, DTS

Neo:6

■ Non-Scaling Conﬁguration

■ CinemaFILTER

■ Crossover Adjustment (60/80/100/120/150 Hz)

■ Onscreen graphical displays

■ Optical Digital Output

■ 2 component video inputs and 1 output

■ 3 Assignable digital inputs (1 coaxial, 2 optical)

■ 5 S-Video inputs and 3 outputs

■ Front panel A/V, S-Video, Optical inputs

■ Multi channel input for DVD-Audio and Super Audio CD

■ Rec out selector and Zone 2 selector

■ Pre-out terminal for Subwoofer

■ Color-coded speaker terminals

FM/AM Tuner Features

■ 40 FM/AM random presets

■ FM auto tuning

■ RDS (European models) with PS/RT/PTY/TP

FM/AM Tuner Features

■ 40 FM/AM random presets

■ FM auto tuning

■ RDS (European models) with PS/RT/PTY/TP

Other Performance Features

■ IntelliVolume

■ Powerful backlit/preprogrammed learning remote

with macro and mode-key LEDs

■ 12V Trigger output for Zone 2

■ IR input terminal

■ Zone 2 Lineout

Other Performance Features

■ IntelliVolume

■ Preprogrammed learning remote with macro and

mode-key LEDs

■ Zone 2 Lineout

■ 12V Trigger output for Zone 2

■ IR input terminal

• *Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” “Surround EX” and the double-D symbol are trademarks of Dolby Laboratories.

• “Theater-Dimensional” is a trademark of Onkyo Corporation.

• “DTS,” “DTS-ES Extended Surround,” and “Neo:6” are trademarks of Digital Theater Systems, Inc.

• Xantech is a registered trademark of Xantech Corporation.

• Niles is a registered trademark of Niles Audio Corporation.

• Re-Equalization and the “Re-EQ” logo are trademarks of THX Ltd. Manufactured under license of THX Ltd.

The alphabet displayed at the end of the product name found in catalogs and on the packages represents the color of this receiver. Though the color varies, the speciﬁcations and operations are the same.

Supplied accessories

Check that the following accessories are supplied with the TX-SR701/701E/ 601/601E.

AM loop antenna × 1 FM indoor antenna × 1

Left

Right

Surround

Right

Left

Surround

Right

Surround

Left

Right

Center

Zone 2

Surround Back

Zone 2

Right

Zone 2

Left

Center

Zone 2

Right

Zone 2

Left

Surround Back

Right

Surround Back

Left

Center

Surround Back

Right

Surround Back

Left

Remote controller × 1

Left

Front

Right

Zone 2

Surround

SP-B

Zone 2

Front

Right

Front

Left

SP-B

Left

SP-B

Right

Surround

Front

Right

Front

Left

SP-B

Left

SP-B

Right

Speaker Cable

Speaker cable label × 1

TX-SR701/701E: RC-533M TX-SR601/601E: RC-515M

Batteries (AA, R6) × 2

Before using this unit

Setting the voltage selector (Worldwide models only)

Worldwide models are equipped with a voltage selector so that you can set your TX-SR701/701E/601/601E to conform with local power supplies. Be sure to set this switch to match the voltage of the power supply in your area before plugging in the unit. Determine the proper voltage for your area: 220-230 V or 120 V. If the preset voltage is not correct for your area, insert a screwdriver into the groove in the switch and slide the switch all the way to the top (120 V) or bottom (220-230 V), whichever is appropriate.

ANTENNA

COMPONENT VIDEO

OUTPUT

INPUT 1

INPUT 2

DIGITAL

COAXIAL

OUT

OPTICAL

COAXIAL

GND

TAPE

PHONO

VIDEO 2

VIDEO 3

ININ

VIDEO 3

VIDEO 2

ZONE 2

LINE OUT

VIDEO 1

DVD

MONITOR

OUTOUT

OUT

OUTOUTOUT

SURR

FRONT

VIDEO 1

VOLTAGE

DVD

SELECTOR

REMOTE CONTROL

ZONE 2

12 V

12 V TRIGGER

TRIGGER

OUT

IR IN

CENTER

SUB WOOFER

ZONE 2 SPEAKERS

AV RECEIVER

MODEL NO. TX

SR 701

120 V

220-230 V

CAUTION: SPEAKER IMPEDANCE

6 OHMS MIN. /SPEAKER

SURROUND

FRONT

SPEAKERS

FRONT SURR CENTER SURR BACK

ZONE 2

PRE OUT

CENTER SPEAKER

AC OUTLETS

SURROUND BACK SPEAKER

(SB)

SWITCHED

TOTAL 100W MAX.

120 V

VOLTAGE

SELECTOR

SUB WOOFER

220-230

Notes:

• Do not mix new batteries with old batteries or different kinds of

• To avoid corrosion, remove the batteries if the remote controller

• Remove dead batteries immediately to avoid damage from corrosion.

Using the remote controller

Point the remote controller toward the remote control sensor. The STANDBY indicator lights up when the unit receives a signal from the remote controller.

The following accessories may be available depending on the area which it was purchased.

Conversion plug × 1

(Use this plug if the power cord plug of the TXSR701/701E/601/601E does not ﬁt your AC outlet. Shape may vary depending on the area which it was purchased.)

75/300 Ω antenna adapter × 1

batteries.

will not be used for a long time.

If the remote controller does not operate smoothly, remove the old batteries and replace them both with two new AA batteries.

Remote control sensor

STANDBY indicator

TX-SR701/701E/601/601E

Installing the remote controller batteries

1. Remove the battery compartment cover by pressing it and sliding it in the direction shown by the arrow below.

2. Insert two AA (R6) batteries into the battery compartment. Carefully follow the polarity diagram (positive (+) and negative (–) symbols) inside the battery compartment.

3. After the batteries are installed and seated correctly, replace the compartment cover.

321

30˚

Approx. 16 feet

(5 meters)

SEND/LEARN indicator

Notes:

• Make sure that the remote control sensor is not subject to strong light such as direct sunlight or inverted ﬂuorescent light for it may prevent proper operation of the remote controller.

• Using another remote controller in the same room or using the TX-SR701/701E/601/601E near equipment that uses infrared rays may cause operational interference.

• Do not put objects on the remote controller. Its buttons may be pressed by mistake and drain the batteries.

• Make sure the audio rack doors do not have colored glass. Placing the TX-SR701/701E/601/601E behind such doors may prevent proper remote controller operation.

• If there is any obstacle between the remote controller and the remote control sensor, the remote controller will not operate.

Front panel facilities

Here is an explanation of the controls and displays on the front panel of the TX-SR701/701E/601/601E.

Front panel

<TX-SR701E>

<TX-SR601E>

STANDBY/ON

POWER

OFF

REC OUT ZONE 2

PHONES

OFF

DIRECT/

PURE AUDIO

LEVEL

PURE AUDIO

AUDIO

SELECTOR

STANDBY

S VIDEO

VIDEO 4

MASTER VOLUME

INPUT

VIDEO

AUDIO

SETUP

ADJUST

RETURN

TUNI NG

PRESET

RT/PTY/TP

DISPLAY

VIDEO

DVD

VIDEO 2

VCR 2VCR 1

LISTENING MODE

STEREO

SURROUND THX DSP

VIDEO 3

VIDEO

MEMORY

FM MODE

CLEAR

TUNER CD

TAPE

PHONO

ENTER

DIGITAL

S VIDEO

VIDEO 4

MASTER VOLUME

INPUT

VIDEO

AUDIO

STANDBY/ON

POWER

OFF

REC OUT ZONE 2

PHONES

AUDIO

SETUP

ADJUST

RETURN

TUNI NG

PRESET

STANDBY

OFF

LEVEL

AUDIO

SELECTOR

RT/PTY/TP

DISPLAY

VIDEO

DVD

VIDEO 2

VCR 2VCR 1

DIRECT

VIDEO 3

LISTENING MODE

SURROUND

VIDEO

MEMORY

DSPSTEREO

FM MODE

CLEAR

C D

TUNER

TAPE

ENTER

DIGITAL

Front panel facilities

For further operational instructions, see the pages indicated in brackets [ ].

POWER switch (for all models other than USA and Canadian models, and Australian models) [28]

Press to turn on and off the main power supply for the TX-SR701/ 701E/601/601E. When the TX-SR701/701E/601/601E is turned on with the POWER switch, the STANDBY indicator lights.

• Before turning on the power, check to make sure that all cords are properly connected.

• When the power is turned on, a sudden surge of current will occur that may adversely affect the operation of other devices. To prevent this, do not plug the TX-SR701/701E/601/601E into the same circuit used by sensitive equipment, e.g., computers.

MEMORY button [38]

Press to assign the radio station that you are currently tuned into to a preset channel or press to delete a previously preset station.

FM MODE button [37]

Press to change the stereo mode from AUTO to MONO and vice versa. Each time this button is pressed, the AUTO indication turns on and off indicating the current mode. If you are listening to an FM radio station in stereo and the sound cuts out or there is a great deal of noise, switch from AUTO to MONO.

Remote control sensor [7]

STANDBY/ON button [28]

If pressed with the POWER switch turned on (with the receiver plugged in for US models and Australian models), the TX-SR701/ 701E/601/601E turns on and the display lights up. If pressed again, the TX-SR701/701E/601/601E returns to the standby state. In the standby state, the display is turned off and the TX-SR701/701E/ 601/601E cannot be operated.

STANDBY indicator [7, 28]

Lights when the TX-SR701/701E/601/601E is in the standby state and when a signal is received from the remote controller.

DISPLAY button [45]

Press to display information about the current input source signal. Each time you press the display button, the screen changes to show you different information concerning the input signal.

RT/PTY/TP (European models only) button [40]

This button is only available on European models. Press this button to tune into the Radio Data System (RDS) for FM broadcasting. RDS was developed within the European Broadcasting Union (EBU) and is available in most European countries. Each time the button is pressed, the display changes from RT (radio text) to PTY (program type) to TP (trafﬁc program) and then back to RT again.

DIMMER button (other than European models)

Press to set the brightness of the front display. There are three settings available: normal, dark, and very dark.

STANDBY

DISPLAY

DIMMER

• The brightness of the front display can also be adjusted using the remote controller.

LISTENING MODE buttons [46-51]

Press these buttons to select a listening mode for the current input source. Press the DIRECT (TX-SR601/601E), THX (TX-SR701/ 701E), STEREO, and SURROUND buttons to select a listening mode directly. Press the DSP button to select any of the possible listening modes for the input source currently selected.

Note:

During playback of a multichannel source, press the DIRECT button to turn off the tone control and the SURROUND button to turn on the tone control. [45]

AUDIO ADJUST button [57]

Press to adjust the sound quality and the listening mode.

SETUP button [31]

Press to enter the Setup Menu. The OSD Menu will appear on the TV monitor as well as the front display on the TX-SR701/701E/ 601/601E.

RETURN button [32]

When in the Setup Menu, press to go back one level. If pressed while at the Main Menu, you will exit the Setup Menu.

TUNING / , PRESET / , cursor ( / / / ) buttons [31, 37, 38]

To tune into a radio station, press the TUNING / buttons. The tuner frequency is displayed in the front display and it can be changed in 100-kHz (or 50-kHz) increments for FM and 10-kHz (or 9-kHz) increments for AM. When FM is selected as the input source, you can hold down either the TUNING or button and then release it to activate the autosearch feature. It will search for a station in the direction of the button you pressed and stop when it tunes into one. When navigating through the menu settings, these buttons move the cursor up or down (or change the highlighted item). To select a radio station that was stored using the MEMORY button, press the PRESET / buttons. When navigating through the menu settings, these buttons select the value or item that you selected with the TUNING / buttons. When you press the SETUP button, the TUNING and PRESET buttons become cursor buttons to be used for Setup Menu operations.

ENTER button [31]

Press to display the screen for the item that is selected in the Setup Menu.

MASTER VOLUME dial [41]

Use to control the volume in the main zone. The volume for the remote zone (Zone 2) is independent.

VIDEO 4 INPUT terminals [21]

For connecting a video camera or game device.

Front display [11]

Front panel facilities

Input source buttons (DVD, VIDEO 1–4, TAPE, TUNER, CD, and PHONO (TX-SR701/701E only)) [41]

These buttons are used to select the input source. Press these buttons to select the input source for the main zone. To select the input source for the remote zone (Zone 2) or recording out (Rec Out), ﬁrst press the ZONE 2 or REC OUT button, and then press the desired input source button. The input channel with its indicator lit red is output to REC OUT and the one with its indicator lit green is output to ZONE 2.

AUDIO SELECTOR button [42]

Press to select the type of audio input signal.

DIRECT/PURE AUDIO button and indicator (TX-SR701/701E only) [46, 48]

PHONES jack [44]

This is a standard stereo jack for connecting stereo headphones.

REC OUT, ZONE 2, OFF, LEVEL / buttons, and ZONE 2 indicator [60, 61]

The REC OUT and ZONE 2 buttons allow you to use the TXSR701/701E/601/601E to output to a remote zone (Zone 2) or to another component for recording (Rec Out). To turn off the output, press the OFF button. The ZONE 2 indicator lights when a signal is output to the remote zone (Zone 2). When the ZONE 2 indicator is off, then either output to the remote zone is turned off or Rec Out is selected. Press the LEVEL / buttons to enter the mode for adjusting the volume in the remote zone (Zone

2).

Note:

The Rec Out and Zone 2 buttons use the same circuit and therefore cannot be used at the same time. When REC OUT is selected, nothing is output to Zone 2. When ZONE 2 is selected, REC OUT is automatically ﬁxed to SOURCE.

Front panel facilities

Front panel display

MUTING indicator

Flashes when the mute function is turned on.

Listening mode or digital input format indicators

One of these indicators lights to show the format of the current input source. In addition, one of the listening mode indicators lights to indicate the current listening mode.

Tuning indicators

TUNED indicator

Lights when a radio station is received.

AUTO indicator

Lights when receiving FM broadcasts in the stereo mode. Turns off when placed into the monaural mode.

RDS indicator (European models only)

Lights when an RDS station is received.

MEMORY indicator

Lights when the MEMORY button is pressed to preset a radio station.

FM STEREO indicator

Lights when an FM broadcast station is received in stereo.

Multi function display

During normal operation, shows the current input source and volume. When the FM or AM input is selected, shows the frequency and preset number. When the DISPLAY button is pressed, shows the listening mode and input source format. However, does not show the source format when the FM or AM source is selected.

SLEEP indicator

Lights when the sleep timer is turned on.

ZONE 2 indicator

Lights when using the remote zone (Zone 2).

REC OUT indicator

Lights when recording the input source from one component to another (Rec Out)

Remote controller

RC-533M

SEND/LEARN indicator

Lights red when signals are sent by the remote controller. It also ﬂashes when a button is pressed when the battery power is low.

ON/STANDBY button [28]

ON: Press to turn on the TX-SR701/701E/601/601E. STANDBY: Press to place the TX-SR701/701E/601/601E in the

standby state. Be aware that pressing the STANDBY button only places the TXSR701/701E/601/601E in standby and does not turn the power completely off.

SLEEP button [44]

Press to set the sleep function. The SLEEP button enables you to set the TX-SR701/701E/601/ 601E to turn off automatically after a speciﬁed time period.

MACRO 1, 2 button [73]

Press to program or execute the macro function.

MODE buttons and indicators [28, 63-74]

Press to select the component to be operated by the remote controller. When a MODE button is pressed, it will light for 8 seconds. The selected MODE button will also light whenever any other operation button is pressed.

RC-515M

RETURN button [32]

Press to enter the selected setting and return to the previous menu.

CH , DISC button

Press to select a preset channel for the tuner (CH). [38] When the CD mode is selected, also press to select a disc when operating components with disc changers (DISC). [65]

CH SEL/TOP MENU button

Press to select a speaker channel when adjusting the speaker level (CH SEL). [43] When the DVD mode is selected, press to display the menu screens of the DVD player (TOP MENU). [64]

AUDIO SEL/TV/VCR button [47]

Press to select the audio input signal. The setting changes from “Auto” to “Multich” (only if DVD is selected as the input source) to “Analog” and back each time this button is pressed.

LEVEL /ANGLE and LEVEL /SUBTITLE buttons

Press to adjust the volume of the speaker selected using the CH SEL button (LEVEL / ). [43] Press the ANGLE button to select a camera angle when playing a DVD-Video with multiple angle playback. Press the SUBTITLE button to select a subtitle language when playing a DVD-Video. [64]

CD/TAPE/DVD/MD operation buttons [63-66]

Press to operate other Onkyo components connected to the TXSR701/701E/601/601E using the terminals.

Remote controller

INPUT SELECTOR buttons [41]

Press to select an input source. Same as the input selector buttons on the front panel of the TXSR701/701E/601/601E. The input source for each button is given here. DVD:DVD, CD:CD, V1:VIDEO1, V2:VIDEO2, V3:VIDEO3, V4:VIDEO4, V5:VIDEO5 (not used with the TXSR701/701E/601/601E), TAP:TAPE, TUN:FM/AM, PH:PHONO (not used with the TX-SR601/601E).

Numeric key/Listening mode, SP A, SP B, CINE FLTR, DISPLAY, DIMMER buttons

1 to 9, +10, --/---, 0: For entering the number of a track. [64-66]

PURE A:

TX-SR601/601E: Not used with the TX-SR601/601E.

TX-SR701/701E: Press to select the Pure Audio mode. [46, 48]

DIRECT, STEREO, SURR, ALL ST, DSP (TX-SR601/601E), DSP / (TX-SR701/701E), THX (TX-SR701/701E): You can

select a listening mode. [48-51]

Note:

During playback of a multichannel source, press the DIRECT button to turn off the tone control and the SURR button to turn on the tone control.

SP A, SP B: Not used with the TX-SR601/601E.

CINE FLTR (TX-SR601/601E): Depending on the listening

mode, you can turn the CinemaFILTER function on or off. [51]

Re-EQ (TX-SR701/701E): Depending on the listening mode, you can turn the Re-EQ function on or off. [49]

DISPLAY: For changing the display in the front display. [45]

DIMMER: Adjusts the display brightness.

There are three settings available: normal, dark, and very dark.

MUTING button [45]

AUDIO ADJUST button [57]

ZONE 2/SEARCH/ENTER button

When the DVD mode is selected, press to ﬁnd the speciﬁc section on a DVD where you want to start playback (SEARCH). [64] When in the RCVR mode, press to perform operations on the remote zone (ZONE 2). [60] When in the MD mode, press to enter the selected song (ENTER). [66]

LIGHT button (RC-533M only)

Press to turn on and off the lights in the buttons of the remote controller.

SETUP button [31]

Press to display the Setup Menu on the TV screen and in the display. Press again to exit the menu.

/ / / , ENTER button [31]

When in the Setup Menu, press the upper and lower arrow buttons to select an item, press the right and left arrow buttons to select parameter values or modes, and press the ENTER button to advance to the next item.

VOL button [41]

Press to adjust the volume.

TEST/MENU button

This button is used to set the speaker output levels. Use this button in conjunction with the LEVEL / and CH SEL buttons to calibrate the speakers levels without entering the Setup Menu. [43] When the DVD mode is selected, press to display the DVD menu (MENU). [64]

Connections

• Be sure to always refer to the instructions that came with the component that you are connecting.

• Do not plug in the power cord until all connections have been properly made.

• For input jacks, red connectors (marked R) are used for the right channel, white connectors (marked L) are used for the left channel, and yellow connectors (marked V) are used for video connection.

• Insert all plugs and connectors securely. Improper connections can result in noise, poor performance, or damage to the equipment.

Improper connection

Inserted completely

• Do not bind audio/video connection cables with power cords and speaker cables. Doing so may adversely affect the picture and sound quality.

Cables are depicted in the connection diagrams as shown below.

Left (white)

Right (red)

Audio connection cable

Component video connection cable

Video connection cable

S video connection cable

Coaxial cable

Optical cable

Connections

TX-SR701/701E

Connecting antennas [29]

COMPONENT VIDEO INPUT/OUTPUT [18-20]

OUTPUT

OPTICAL

ANTENNA

VIDEO 3

COAXIAL

OUT

COAXIAL

TAPE

VIDEO 3

GND

COMPONENT VIDEO

INPUT 2

OPTICAL

PHONO

INPUT 1

DIGITAL

audio components [16]

When using the Zone 2 LINE OUT terminals [23]

VIDEO 2

ININ

VIDEO 2

ZONE 2

LINE OUT

VIDEO 1

DVD

OUTOUT

OUTOUTOUT

FRONT

VIDEO 1

Connecting your video components [17]

REMOTE

CONTROL [24]

12V TRIGGER ZONE 2 terminal [21]

ZONE SPEAKERS

ZONE 2

12 V

12 V TRIGGER

TRIGGER OUT

OUT

IR IN

MONITOR OUT

SURR

DVD

REMOTE CONTROL

CENTER

SUB WOOFER

IR IN [22]Connecting your

When using the ZONE 2 SPEAKERS terminals [23]

Connecting speakers [26] AC OUTLETS [24]

CAUTION: SPEAKER IMPEDANCE

FRONT SPEAKERS

PRE OUT

6 OHMS MIN. /SPEAKER

SURROUND SPEAKERS

FRONT SURR CENTER SURR BACK

ZONE 2

SUB WOOFER

CENTER SPEAKER

(SB)

SURROUND BACK SPEAKER

MODEL NO. TX

PRE OUT [21]

When using the ZONE 2 PRE OUT terminals [23]

AC OUTLETS

AC 230-240 V 50

TOTAL 100W MAX.

AV RECEIVER

SWITCHED

SR 701E

TX-SR601/601E

Connecting antennas [29]

COMPONENT VIDEO INPUT/OUTPUT [18-20]

COMPONENT VIDEO

OUTPUT

INPUT 1INPUT 2

DIGITAL

OUT

OPTICAL

audio components [16]

TAPE

When using the Zone 2 LINE OUT terminals [23]

ANTENNA

COAXIAL

VIDEO 2

VIDEO 3

INININ

VIDEO 3

VIDEO 2

ZONE 2

LINE OUT

VIDEO 1

OUTOUT

OUTOUTOUT

VIDEO 1

MONITOR

DVD

OUT

SURR

FRONT

Connecting your video

REMOTE

CONTROL [24]

12V TRIGGER ZONE 2 terminal [21]

REMOTE CONTROL

ZONE 2

12 V

12 V TRIGGER

TRIGGER

OUT

IR IN

CENTER

SUB WOOFER

DVD

IR IN [22]Connecting your

ZONE SPEAKERS

Connecting speakers [26] AC OUTLETS [24]

CAUTION: SPEAKER IMPEDANCE

6 OHMS MIN. /SPEAKER

SURROUND SPEAKERS

SUBWOOFER

FRONT SPEAKERS

PRE OUT [21]

PRE OUT

CENTER SPEAKER

SURROUND BACK

SPEAKER

MODEL NO. TX

AV RECEIVER

AC OUTLETS

AC 230-240 V 50

SWITCHED

TOTAL 100W MAX.

SR 601E

components [17]

When using the ZONE 2 SPEAKERS terminals [23]

Connections

Here is an explanation of typical ways to connect various components to the TX-SR701/701E/601/601E. There are many ways that any one component can be connected, and it is up to you to decide which method best ﬁts your situation. The directions given here are only one option and should only be thought of as such. It is best to fully understand the nature of each connector and terminal as well as those of your components and their features to ascertain which method of connection is best.

Digital audio output (coaxial)

1. CD player (CD)

Analog audio output

2. Turntable (PHONO) (701/701E only)

Analog audio output

L (white)

R (red)

Ground wire (earth)

L (white)

R (red)

GND

COMPONENT VIDEO

INPUT 2

OPTICAL

PHONO

INPUT 1

DIGITAL

OUTPUT

OPTICAL

ANTENNA

COAXIAL

OUT

COAXIAL

TAPE

VIDEO 3

ININ

VIDEO 3

OUT

OUTOUT

VIDEO 2

L (white)

R (red)

3. Cassette tape deck, MD recorder, DAT deck, or CD recorder (TAPE)

Digital audio input (optical)

Analog audio output

L (white)

Analog audio input

: Signal flow

Connecting your audio components

Below is an example of how you can connect your audio components to the TX-SR701/701E/601/601E. Refer to the diagram above for the following connection examples.

IN/OUT (analog audio)

These are the analog audio inputs and outputs. There are seven audio inputs and three audio outputs on the rear panel. The audio inputs and outputs require RCA-type connectors.

DIGITAL INPUT/OUTPUT

On the rear panel of the TX-SR701/701E/601/601E, there are one coaxial digital input, two optical digital inputs, one coaxial digital output (TX-SR701/701E only), and one digital output. To the digital inputs, connect CD players, LD players, DVD players, or other digital source component. To the digital outputs, connect MD recorders, CD recorders, DAT decks, or other similar components.

• Since an analog connection must be made when using REC OUT or ZONE 2, make sure that the connection to the input source is not digital only, but analog as well.

• When using an optical input or output jack, always use an optical ﬁber cable.

1. Connecting a compact disc player (CD)

Using an RCA audio cable, connect the output jacks of the compact disc player to the CD audio jacks of the TX-SR701/701E/601/601E. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the compact disc player has a digital output, connect it to either the DIGITAL INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of the TX-SR701/701E/601/601E depending on the type of connector on the compact disc player.

With the initial settings of the TX-SR701/701E/601/601E, the CD input source is set for digital input at the COAXIAL jack (COAX).

If the digital connection is made to a different jack, this must be changed at “Input Setup” → “Digital Input” (see page 52).

2. Connecting a turntable (PHONO) (TX-SR701/701E only)

Using an RCA audio cable, connect the output jacks of the turntable to the PHONO audio jacks of the TX-SR701/701E. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

Note:

The TX-SR701/701E is designed for use with moving magnet cartridges. For proper operation, connect a ground (or earth) wire to the GND terminal. For some turntables, however, connecting the ground wire may cause increased noise, and in such a case, a ground wire is not necessary and should not be connected.

3. Connecting a cassette tape deck, MD recorder, DAT deck, or CD recorder (TAPE)

Using RCA audio cables, connect the output jacks (PLAY) of the device to the TAPE IN audio jacks of the TX-SR701/701E/601/ 601E and connect the input jacks (REC) of the device to the TAPE OUT audio jacks of the TX-SR701/701E/601/601E. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If the device has a digital output, connect it to either the DIGITAL IN COAXIAL jack or the DIGITAL IN OPTICAL jack of the TX-SR701/ 701E/601/601E depending on the type of connector on the device.

With the initial settings of the TX-SR701/701E/601/601E, nothing is allocated as the digital input source for TAPE (----).

If you connect the digital audio output, be sure to make the appropriate changes at “Input Setup” → “Digital Input” (see page

52).

If the device has a digital input, connect it to the DIGITAL OUTPUT jack of the TX-SR701/701E/601/601E for digital recording of the signal from the digital input of the TX-SR701/ 701E/601/601E.

Note:

The output from the DIGITAL OUT jack of the TX-SR701/701E/ 601/601E is only the digital signal input to the DIGITAL IN jack.

Connections

Connecting a DVD Player with 5.1-Channel Output

: Signal flow

GND

COMPONENT VIDEO

INPUT 2

OPTICAL

PHONO

INPUT 1

DIGITAL

OUTPUT

OPTICAL

ANTENNA

COAXIAL

OUT

COAXIAL

VIDEO 3

ININ

VIDEO 2

ZONE 2

LINE OUT

VIDEO 1

OUTOUT

OUTOUTOUT

DVD

FRONT

REMOTE CONTROL

MONITOR

ZONE 2

OUT

12 V

12 V TRIGG

TRIGG

OUT

IR IN

SURR

CENTER

Component video output

Video output

S video output

4. DVD player (DVD)

TAPE

VIDEO 3

VIDEO 2

VIDEO 1

SUB WOOFER

DVD

Analog audio output (center)

Analog audio output (subwoofer)

L (white)

R (red)

L (white)

Analog audio output (surround L/R)

Analog audio output (front L/R)

R (red)

Digital audio output (optical)

Connecting your video components

Below is an example of how you can connect your video components to the TX-SR701/701E/601/601E. Refer to the diagram above for the following connection examples. Video signal will be output if you use any one of COMPONENT, S, or composit terminals. However, you are recommended to match the type of video terminals for connection between video devices (ex. DVD player and VCR), TX-SR701/701E/601/601E and TV/monitor.

COMPONENT VIDEO INPUT/OUTPUT

For DVD players or other devices that have component video connectors, the TX-SR701/701E/601/601E has two banks of component video input connectors (Y, PB, PR) for direct component video input. TX-SR701/701E/601/601E also has one bank of component video output connectors for direct component video output to the matrix decoder of a television, projector, or other display device. By sending the pure component video signal directly, the signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly lifelike colors and crisp detail.

• The signal that comes in from COMPONENT VIDEO INPUT is only sent to COMPONENT VIDEO OUTPUT. When connecting a video player to the COMPONENT VIDEO INPUT jacks, be sure to connect your television to the COMPONENT VIDEO OUTPUT jacks.

VIDEO IN/OUT, S VIDEO IN/OUT

These are the video inputs and outputs. On the rear panel, there are four video inputs and two video outputs and each one includes both composite video and S video conﬁgurations. Connect VCRs, VTRs, LD players, DVD players, and other video components to the video inputs. Connect VCRs, VTRs, and other recording components to the video outputs to make video recordings.

• When connecting a VCR or other video component, make sure you connect its audio and video leads to the same bank (e.g., both to VIDEO 3).

• The VIDEO 4 inputs are located on the front panel.

The ﬂow of the video signals is as follows:

The signal that comes in from a VIDEO IN jack is sent to both the VIDEO OUT and S VIDEO OUT jacks. The signal that comes in from a S VIDEO IN jack is sent to both the S VIDEO OUT and VIDEO OUT jacks. It is not necessary to make both video and S video connections.

Notes:

• If your video output device (e.g., television or projector) is connected only to the MONITOR OUT VIDEO jack, MONITOR OUT S VIDEO jack, or both, and the video signal from the source component is input through the component video connectors, no picture will appear. Video sources input from the component video connectors can only be output from the component video connectors.

• For more information about the DIGITAL INPUT/OUTPUT jacks, see page 16.

Connections

Connecting a DVD Player with 2-Channel (L/R) Audio Output

GND

COMPONENT VIDEO

INPUT 2

OPTICAL

PHONO

INPUT 1

DIGITAL

OUTPUT

OPTICAL

ANTENNA

COAXIAL

OUT

COAXIAL

TAPE

VIDEO 3

ININ

VIDEO 3

VIDEO 2

ZONE 2

LINE OUT

VIDEO 1

OUTOUT

OUTOUTOUT

VIDEO 1

: Signal flow

4. Connecting a DVD player (DVD)

Using an RCA video cable, connect the video output jack (composite) of the DVD player to the DVD V IN jack of the TXSR701/701E/601/601E. Or if the DVD player has an S video output jack, connect it to the DVD S IN jack with an S video cable. Or if the device has component video outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2 jacks on the TX-SR701/ 701E/601/601E.

With the initial settings of the TX-SR701/701E/601/601E, the DVD input source is set for the COMPONENT VIDEO INPUT 1 jacks.

If you connect the DVD player to the COMPONENT VIDEO INPUT 2 jacks, this must be changed at “Input Setup” → “Component Video” (see page 53).

Using an RCA audio connection cable, connect the audio output jacks of the DVD player to the DVD FRONT L/R jacks of the TXSR701/701E/601/601E. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device has a 5.1-channel output, connect the DVD FRONT L/ R, SURR L/R, CENTER, and SUBWOOFER (5.1-channel input) jacks of the TX-SR701/701E/601/601E to the 5.1-channel output jacks of the DVD player. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If the device has a digital output, connect it to either the DIGITAL IN COAXIAL jack or the DIGITAL IN OPTICAL jack of the TXSR701/701E/601/601E depending on the type of connector on the DVD player.

With the initial settings of the TX-SR701/701E/601/601E, the DVD input source is set for digital input at the OPTICAL 1 jack (OPT 1).

If the digital connection is made at a different jack, this must be changed at “Input Setup” → “Digital Input” (see page 52).

Note:

If the DVD player has both 5.1-channel audio outputs and 2channel audio outputs, and you want to connect the DVD player only using the FRONT L/R jacks on the TX-SR701/701E/601/ 601E, use the 2-channel audio output jacks on the DVD player.

DVD

FRONT

Component video output

REMOTE CONTROL

MONITOR

ZONE 2

OUT

12 V

12 V TRIGG

TRIGG

OUT

IR IN

SURR

CENTER

Video output

S video output

4. DVD player (DVD)

SUB WOOFER

DVD

L (white)

Analog audio output

R (red)

Digital audio output (optical)

Connections

S Video input

Video input

Video output

S Video output

5. VCR (VIDEO 1)

L (white)

R (red)

L (white)

R (red)

L (white)

R (red)

Video output

S Video output

6. Satellite tuner or television (VIDEO 3)

Analog audio input

Analog audio output

Digital audio output (optical)

: Signal flow

Analog audio output

Component video output

5. Connecting a video cassette recorder (VIDEO 1)

Using RCA video cables, connect the video output jack (composite) of the video cassette recorder to the VIDEO 1 V IN jack of the TXSR701/701E/601/601E and connect the video input jack of the video cassette recorder to the VIDEO 1 V OUT jack of the TX-SR701/ 701E/601/601E. Or if the video cassette recorder has S video input and output jacks, using S video cables, connect the S video output jack of the video cassette recorder to the VIDEO 1 S IN jack of the TX-SR701/701E/601/601E and connect the video input jack of the video cassette recorder to the VIDEO 1 S OUT jack of the TXSR701/701E/601/601E. Or if the video cassette recorder has component video outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2 jacks on the TX-SR701/701E/601/601E.

With the initial settings of the TX-SR701/701E/601/601E, the VIDEO 1 input source is set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the video cassette recorder to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at “Input Setup” → “Component Video” (see page 53).

Using RCA audio cables, connect the audio output jacks of the video cassette recorder to the VIDEO 1 IN audio jacks of the TXSR701/701E/601/601E and connect the audio input jacks of the video cassette recorder to the VIDEO 1 OUT audio jacks of the TXSR701/701E/601/601E. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If you are connecting a digital output device to the VIDEO 1 jack instead of a VCR, connect it to either the DIGITAL IN COAX jack or DIGITAL IN OPT jack depending on the type of connector on the device.

With the initial settings of the TX-SR701/701E/601/601E, nothing is allocated as the digital input source for VIDEO 1 (----).

If you connect the digital audio output, be sure to make the appropriate changes at “Input Setup” → “Digital Input” (see page

52).

GND

COMPONENT VIDEO

INPUT 2

OPTICAL

PHONO

INPUT 1

DIGITAL

OUTPUT

OPTICAL

ANTENNA

COAXIAL

OUT

COAXIAL

TAPE

VIDEO 3

ININ

VIDEO 3

VIDEO 2

ZONE 2

LINE OUT

VIDEO 1

OUTOUT

OUTOUTOUT

VIDEO 1

DVD

FRONT

REMOTE CONTROL

MONITOR

ZONE 2

OUT

12 V

12 V TRIGG

TRIGG

OUT

IR IN

SURR

CENTER

SUB WOOFER

DVD

6. Connecting a satellite tuner, television, or settop box (VIDEO 3)

Using an RCA video cable, connect the video output jack (composite) of the device to the VIDEO 3 V IN jack of the TXSR701/701E/601/601E. Or if the device has an S video output jack, connect it to the VIDEO 3 S IN jack of the TX-SR701/701E/601/ 601E using an S video cable. Or if the device has component video outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2 jacks on the TX-SR701/701E/601/601E.

With the initial settings of the TX-SR701/701E/601/601E, the VIDEO 3 input source is set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the device to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at “Input Setup” → “Component Video” (see page 53).

Using an RCA audio cable, connect the audio output jack of the device to the VIDEO 3 IN audio jacks of the TX-SR701/701E/601/ 601E. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device has a digital output, connect it to either the DIGITAL IN COAXIAL jack or the DIGITAL IN OPTICAL jack of the TXSR701/701E/601/601E depending on the type of connector on the device.

With the initial settings of the TX-SR701/701E/601/601E, the VIDEO 3 input source is set for digital input at the OPTICAL 2 jack (OPT 2).

If the digital connection is made at a different jack, this must be changed at “Input Setup” → “Digital Input” (see page 52).

Connections

E O

8. TV monitor or projector (MONITOR OUT)

7. DVD recorder, other digital video recording device (VIDEO 2)

Digital audio input (coaxial)

TX-SR701/701E only

Video input

S Video input

Analog audio input

L (white)

R (red)

GND

COMPONENT VIDEO

INPUT 2

OPTICAL

PHONO

INPUT 1

DIGITAL

OUTPUT

OPTICAL

ANTENNA

VIDEO 3

COAXIAL

OUT

ININ

COAXIAL

TAPE

VIDEO 3

L (white)

Analog audio output

R (red)

S Video output

Video output

7. Connecting a DVD recorder or other digital video recording device (VIDEO 2)

Using RCA video cables, connect the video output jack (composite) of the device to the VIDEO 2 V IN jack of the TX-SR701/701E/ 601/601E and connect the video input jack of the device to the VIDEO 2 V OUT jack of the TX-SR701/701E/601/601E. Or if the device has S video input and output jacks, using S video cables, connect the S video output jack of the device to the VIDEO 2 S IN jack of the TX-SR701/701E/601/601E and connect the video input jack of the device to the VIDEO 2 S OUT jack of the TX-SR701/ 701E/601/601E. Or if the device has component video outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2 jacks on the TX-SR701/701E/601/601E.

With the initial settings of the TX-SR701/701E/601/601E, the VIDEO 2 input source is set for the COMPONENT VIDEO INPUT 2 jacks.

If you connect the device to the COMPONENT VIDEO INPUT 1 jacks, this must be changed at “Input Setup” → “Component Video” (see page 53).

Using RCA audio cables, connect the audio output jacks of the device to the VIDEO 2 IN audio jacks of the TX-SR701/701E/601/ 601E and connect the audio input jacks of the device to the VIDEO 2 OUT audio jacks of the TX-SR701/701E/601/601E. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If the device has a digital output, connect it to either the DIGITAL IN COAXIAL jack or the DIGITAL IN OPTICAL jack of the TXSR701/701E/601/601E depending on the type of connector on the device.

With the initial settings of the TX-SR701/701E/601/601E, nothing is allocated as the digital input source for VIDEO 2 (----).

If you connect the digital audio output, be sure to make the appropriate changes at “Input Setup” → “Digital Input” (see page

52).

If the device has a digital input, connect it to the DIGITAL OUTPUT jack of the TX-SR701/701E/601/601E for digital recording of the signal from the digital input of the TX-SR701/ 701E/601/601E.

VIDEO 2

ZONE 2

LINE OUT

VIDEO 1

OUTOUT

OUTOUTOUT

VIDEO 1

DVD

FRONT

REMOT CONTR

MONITOR

OUT

SURR

CENTE

SUB WOOFE

DVD

Component video input

Video input

S Video input

: Signal flow

Note:

The output from the DIGITAL OUT jack of the TX-SR701/701E/ 601/601E is only the digital signal input to the DIGITAL IN jack.

8. Connecting a television monitor or projector (MONITOR OUT)

The TX-SR701/701E/601/601E is equipped with a simple Y/C separate circuit and simple Y/C mixed circuit. Since both the signal from the S and V inputs are output to the MONITOR OUT S output, if the television or projector is equipped with an S video input, it is unnecessary to connect the video connectors. If it is equipped with only a video input, connect it to the MONITOR OUT V output.

Using an RCA video cable, connect the video input jack (composite) of the device to the MONITOR OUT V jack of the TXSR701/701E/601/601E. Or if the device has an S video input jack, connect it to the MONITOR OUT S jack of the TX-SR701/701E/ 601/601E using an S video cable. Or if the device has component video inputs, connect them to the bank of COMPONENT VIDEO OUTPUT jacks on the TX-SR701/701E/601/601E.

Note:

Note that the Setup Menu will only be displayed on the monitor connected to MONITOR OUT (S or V) and not those connected to the COMPONENT VIDEO OUTPUT jacks.

Connections

SUR BAC SPE

FRONT SURR CENTER SURR BACK

(SB)

ZONE 2

SUB WOOFER

PRE OUT

6521 43 87

1. Front right speaker

2. Front left speaker

3. Surround right speaker

4. Surround left speaker

5. Subwoofer

6. Center speaker

7. Surround back right speaker

8. Surround back left speaker

L (white)

R (red)

Power amplifier

R (red)

L (white)

R (red)

Subwoofer

Surround

Front

Center

Surround back

9. Connecting video camera, etc. (VIDEO 4 INPUT)

Using an RCA video cable, connect the video output jack (composite) of the device to the VIDEO 4 VIDEO jack of the TXSR701/701E/601/601E. Or if the device has an S video output jack, connect it to the VIDEO 4 S VIDEO jack of the TX-SR701/701E/ 601/601E using an S video cable.

Using an RCA audio cable, connect the audio output jack of the device to the VIDEO 4 AUDIO jacks of the TX-SR701/701E/601/ 601E. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device has an optical digital output, connect it to the VIDEO 4 DIGITAL jack of the TX-SR701/701E/601/601E.

The VIDEO 4 digital input is ﬁxed to the OPTICAL input on the front panel.

S Video output

Digital output (optical)

9. Video camera/ Video game (VIDEO 4 INPUT)

PRE OUT (TX-SR701/701E only)

These jacks are for connecting an auxiliary power ampliﬁer.

You can use an auxiliary power ampliﬁers to listen at louder volumes than you can with the TX-SR701/701E alone. When using a power ampliﬁer, connect each speaker to the power ampliﬁer.

Video output

L (white)

Analog output

R (red)

12V TRIGGER ZONE 2 terminal

When the TX-SR701/701E/601/601E is in the ZONE 2 mode, this terminal outputs at 12 V/100 mA.

Note:

If you use a power ampliﬁer connected to the SURR BACK PRE OUT terminal and connect two surround back speakers to the ampliﬁer, set the “Hardware Conﬁg” → “b. Surr Back” setting to “2ch (PRE OUT)” (see page 55).

Operating components not reached by the remote controller signals (IR IN)

In order to use the remote controller to control the TX-SR701/ 701E/601/601E from a remote location, you will need to prepare a multi-room kit (sold separately) such as one of those given below:

• Onkyo’s Multi-Room System kit (IR Remote Controller Extension System)

• Multiroom A/V distribution and control system such as those from Niles

and Xantech

If the remote controller signal does not reach the TX-SR701/701E/601/601E remote sensor

If the TX-SR701/701E/601/601E is located inside a cabinet or other enclosure where the infrared rays from the remote controller cannot enter, then operation with the remote controller will not be possible. In such a case, it will be necessary to install a remote sensor at a location outside of the cabinet where the infrared rays from the controller can reach. With this connection, select “Main” at “Hardware Conﬁg” → “IR IN Position” (see page 55).

IR Receiver

IR IN

Connecting block

Make the connections as shown below. Do not plug in any equipment to the power outlet until all the connections are complete.

From connecting block

Mini plug cable

REMOTE CONTROL

MONITOR

ZONE 2

OUT

12 V

12 V TRIGGER

TRIGGER

OUT

IR IN

TX-SR701/701E/601/601E

TX-SR701/ 701E/601/ 601E

Remote Controller

In the cabinet

: Signal ﬂow

The IR IN input allows you to control the TX-SR701/701E/601/ 601E from the remote zone (Zone 2) with the remote controller even though the remote zone may be on the other side of the building from the main zone. The diagram below shows how to make the proper connections for the remote zone. With this connection, select “Zone 2” at “Hardware Conﬁg” → “IR IN Position” (see page 55).

IR IN

IR Receiver

TX-SR701/701E/ 601/601E

Connecting block

Remote Controller

Main room Zone 2 room

: Signal ﬂow

Connecting the remote zone (Zone 2) speakers

Remote Zone (Zone 2)

Zone 2

Left speaker

Zone 2

Right speaker

Zone 2 ampliﬁer

Right (red)

Left (white)

Main Room

TX-SR701/701E/601/601E

The TX-SR701/701E/601/601E allows you to listen to two separate input sources at the same time. This allows you to, for example, place speakers in two different rooms so that two or more people can enjoy two different kinds of music at the same time. The room where the TX-SR701/701E/601/601E is actually located is referred to as the main room while the separate room is referred to as the remote zone (Zone 2). In addition, the IR IN terminal of the TXSR701/701E/601/601E allows you to control the TX-SR701/701E/ 601/601E from the remote zone (Zone 2) with the remote controller even though the remote zone is physically separated. The diagrams below show how to make the proper connections for the remote zone.

When using the ZONE 2 SPEAKERS terminals

ZONE 2

You can connect the speakers for the remote zone (Zone 2) to the ZONE 2 SPEAKERS terminals. When you connect the speakers to the ZONE 2 SPEAKERS terminals, set the “Hardware Conﬁg” setting to “Zone 2.” In this setting, while you use the remote zone (Zone 2), surround playback will not be available for the main room (2ch stereo playback only). When you are not using the Zone 2, 6.1-channel playback will be available for the main room.

Main Room

Remote Zone (Zone 2)

Note:

The ZONE 2 out terminals of the TX-SR701/701E/601/601E are of a ﬁxed output level.

LINE OUT

REMOTE CONTROL

TX-SR701/701E/601/601E

Note:

It is important to be aware of the speaker impedance (see page 31).

When using the ZONE 2 LINE OUT terminals

The ZONE 2 LINE OUT terminal is a constant output. Connect to the LINE input of the ampliﬁer (CD, tape, etc.). Adjust the volume with the ampliﬁer connected to the ZONE 2 LINE OUT terminal. In this connection, whatever the “Hardware Conﬁg” setting is set to,

6.1 channel playback is always available for main room.

1. Connect the TX-SR701/701E/601/601E to the ampliﬁer for the remote zone.

2. Connect the remote zone speaker cables to the speaker terminals on the ampliﬁer.

ZONE 2 SPEAKERS

Zone 2

speaker

Left

Zone 2

Right

speaker

When using the ZONE 2 PRE OUT terminals (TX-SR701/701E only)

You can connect the ampliﬁer for the remote zone (Zone 2) to the ZONE 2 PRE OUT terminals and connect the remote zone speakers. When you connect the speakers to the ZONE 2 SPEAKERS terminals, set the “Hardware Conﬁg” setting to “Zone 2.” In this setting, while you use the remote zone (Zone 2), surround playback will not be available for the main room (2ch stereo playback only). When you are not using the Zone 2, 6.1-channel playback will be available for the main room.

Remote Zone (Zone 2)Main Room

Zone 2

Right

speaker

TX-SR701/701E

FRONT SURR CENTER SURR BACK

ZONE 2

PRE OUT

(SB)

SUB WOOFER

Left (white)

Right (red)

Zone 2

Left

speaker

Power ampliﬁer

Connections

AC OUTLETS

The TX-SR701/701E/601/601E is equipped with AC mains outlets for connecting the power cords from other devices so that their power is supplied through the TX-SR701/701E/601/601E. By doing this, you can leave the connected device turned on and have the STANDBY/ON button on the TX-SR701/701E/601/601E turn on and off the device together with the TX-SR701/701E/601/601E.

The shape, number, and total capacity of the AC outlets may differ depending on the area of purchase.

Caution:

Make sure that the total capacity of the components connected to the TX-SR701/701E/601/601E does not exceed the capacity that is printed on the rear panel (e.g., TOTAL 120W).

AC OUTLETS

AC 230-240 V 50

SWITCHED

TOTAL 100W MAX.

European and

some Asian models

REMOTE CONTROL

The terminal on the TX-SR701/701E/601/601E is for connecting other Onkyo components equipped with the same terminal. When a component is connected to the terminal, it can be operated by the remote controller supplied with the TX-SR701/ 701E/601/601E. In addition, when you connect a component to the

terminal, you can also perform the system operations given

below.

Power on/ready function

When the TX-SR701/701E/601/601E is in the standby state, if an

-connected component is turned on, the TX-SR701/701E/601/ 601E also turns on and the input source selected at the TX-SR701/ 701E/601/601E automatically switches to that component. Be aware that this function will not work if the power cord for the connected component is connected to the AC OUTLET on the TXSR701/701E/601/601E, or if the TX-SR701/701E/601/601E has already been turned on.

Direct change function

When the play button is pressed at an -connected component, the input source selected at the TX-SR701/701E/601/601E automatically changes to that component.

Power off function

When the TX-SR701/701E/601/601E is placed in the standby state, all -connected components are also automatically put into the standby state. Also, if you press the ON button on the TX-SR701/701E/601/601E remote controller while the TX-SR701/701E/601/601E is turned on, all -connected components (DVD players, CD players, MD recorders, tuners, etc.) are also turned on.

AC OUTLETS

AC 120 V 60 Hz

SWITCHED

TOTAL 120W 1A MAX.

USA and Canadian

models

Dimmer function

The Dimmer function (display brightness adjustment) of the TXSR701/701E/601/601E can be used to synchronize the display brightness on the connected device using the connection.

Caution:

If an MD recorder is connected to the TAPE jack on the TX-SR701/ 701E/601/601E, switch the Input Selector from TAPE to MD (see page 43).

TX-SR701/701E/601/601E

connector

Ex: Onkyo CD player

connector

Ex: Onkyo cassette tape deck

To connect components using the terminal, simply connect a remote control cable from this terminal to the terminal of the other component. An remote control cable with a 1/8-inch (3.5-mm) miniature two-conductor plug comes with every cassette tape deck, compact disc player, MD recorder, and DVD player that has an terminal.

• When performing operations with -connected components using the system, do not use the remote zone (Zone 2) .

• For remote control operation, the audio connection cables must also be connected.

• If a component has two terminals, you can use either one to connect to the TX-SR701/701E/601/601E. The other one can be used to daisy chain with another component.

• With Onkyo DVD players, you can enter the pre-program code so that you can operate the DVD player directly with the remote controller without connecting the terminals (see page 67).

+ 56 hidden pages