Onkyo DR-S501 User Manual
DVD Receiver
DR-S501
Contents
Overview .........................................2
Instruction Manual
Thank you for purchasing the Onkyo DVD
receiver. Read this manual carefully before using
your new DVD receiver. A good understanding
of its features and operation will allow you to
achieve optimum performance and enjoyment.
Connections.................................. 17
Getting Started and Setting up ...29
Basic Operations.......................... 31
Playback Techniques ................... 44
Advanced Operations .................. 52
Detailed Settings .......................... 55
Keep this manual for future reference.
Miscellaneous information ..........68
Remote Control Codes List
–The end of this manual–
E
n
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Important Safety Instructions
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12.
Use only with the cart, stand,
PORTABLE CART WARNING
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to
S3125A
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions:
A. When the power-supply cord or plug is dam-
aged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the operating instructions as an improper adjustment of
other controls may result in damage and will
often require extensive work by a qualified technician to restore the apparatus to its normal
operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall
be placed on the apparatus.
Don’t put candles or other burning objects on top of this
unit.
17. Batteries
Always consider the environmental issues and follow local
regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is adequate ventilation.
Leave 20 cm (8") of free space at the top and sides and 10
cm (4") at the rear. The rear edge of the shelf or board
above the apparatus shall be set 10 cm (4") away from the
rear panel or wall, creating a flue-like gap for warm air to
escape.
2
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.
AC outlet voltages vary from country to country. Make
sure that the voltage in your area meets the voltage
requirements printed on the unit’s rear panel (e.g., AC 230
V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit from
the AC power source. Make sure that the plug is readily
operable (easily accessible) at all times.
Pressing the [STANDBY/ON] button to select Standby
mode does not fully shutdown the unit. If you do not
intend to use the unit for an extended period, remove the
power cord from the AC outlet.
5. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
• When you’ve finished using this unit, remove all
discs and turn off the power.
7. Installing this Unit
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all
around this unit, especially if it’s installed in an
audio rack. If the ventilation is inadequate, the
unit may overheat, leading to malfunction.
• Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may
rise, shortening the life of the optical pickup.
• Avoid damp and dusty places, and places subject
to vibrations from loudspeakers. Never put the
unit on top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on its
side or on a sloping surface, because it may cause
a malfunction.
• If you install this unit near a TV, radio, or VCR,
the picture and sound quality may be affected. If
this occurs, move this unit away from the TV,
radio, or VCR.
8. To Obtain a Clear Picture—This unit is a high-
tech, precision device. If the lens on the optical
pickup, or the disc drive mechanism becomes dirty
or worn, the picture quality may be affected. To
maintain the best picture quality, we recommend
regular inspection and maintenance (cleaning or
worn part replacement) every 1,000 hours of use
depending on the operating environment. Contact
your Onkyo dealer for details.
9. Moisture Condensation
Moisture condensation may damage this unit.
Read the following carefully:
Moisture may condense on the lens of the optical
pickup, one of the most important parts inside this
unit.
• Moisture condensation can occur in the following
situations:
– The unit is moved from a cold place to a warm
place.
– A heater is turned on, or cold air from an air
conditioner is hitting the unit.
– In the summer, when this unit is moved from
an air conditioned room to a hot and humid
place.
– The unit is used in a humid place.
• Do not use this unit when there’s the possibility
of moisture condensation occurring. Doing so
may damage your discs and certain parts inside
this unit.
If condensation does occur, remove all discs and
leave this unit turned on for two to three hours. By
this time, the unit will have warmed up and any condensation will have evaporated.
3
Precautions—Continued
10. Region Numbers—The DVD standard uses region
numbers to control how discs can be played around
the world, the world being divided into six regions.
This unit will only play DVD discs that match its
region number, which can be found on its rear panel
ALL
1
(e.g., , ).
11. About this Manual—This manual explains how to
use all of this unit’s functions. Although the DVD
standard offers many special features, not all discs
use them all, so depending on the disc being played,
this unit may not respond to certain functions. See
the disc’s sleeve notes for supported features.
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT”. So, to
use this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store
where you purchased the unit.
To prevent being exposed to the laser beam, do not try to
open the enclosure.
CAUTION:
CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
The label on the right is
applied on the rear panel.
1. This unit is a CLASS 1
LASER PRODUCT and
employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not
remove the cover. Refer servicing to qualified personnel.
For European Models
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
ONKYO EUROPE ELECTRONICS GmbH
4
K. MIYAGI
Supplied Accessories
Make sure you have the following accessories:
RC-704S
Remote controller & 2 batteries (AA/R6)
Video cable (RCA) (1.5 m)
Indoor FM antenna
AM loop antenna
Powe r cord
* In catalogs and on packaging, the letter at the end of
the product name indicates the color. Specifications
and operations are the same regardless of color.
5
Introduction
Features
Highlights
•Dolby*1 Digital, DTS
• DVD-Video, Video CD, audio CD
•MP3, WMA,
*3
• DVD-Audio and Super Audio CD
• CD-R/RW, DVD-R/RW, and DVD+R/RW compatible
• HDMI
*5
digital interface
*2
JPEG, DivX
®*4
Video
• HDMI Pass-Thru
(1080p Compatible; 1 Input/1 Output)
• HDTV-Capable (50 MHz)
• JPEG in High Definition
• Advanced 108 MHz/14-bit video D/A converter
• 2 Composite Video Inputs
• Component and composite video outputs
• 1 SCART Connector (European model only)
• Repeat/A-B Repeat/Random/Memory playback
• Supports 4:3 and 16:9 aspect ratio TVs
• Three view modes providing a best-fit picture regardless of TV aspects
• Picture Zoom Function
• Parental Lock function
• Screen Saver function
Audio
• 192 kHz/24-bit D/A converter
• 2 Digital Inputs (1 Optical/1 Coaxial)
• Theater-Dimensional
• Direct Mode and Pure Audio Mode
• Dynamic Range Control setting
*6
Virtual Surround
*1
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks of
Dolby Laboratories.
*2
“DTS” is a registered trademark of DTS, Inc. and “96/24” is a
trademark of DTS, Inc.
*3
Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United
States and/or other countries.
*4
DivX, DivX Certified, and associated logos are trademarks of
DivX, Inc. and are used under license.
*5
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.
*6 “Theater-Dimensional” is a trademark of Onkyo Corporation.
* Apple and iPod are trademarks of Apple, Inc., registered in the
U.S. and other countries.
This product incorporates copyright protection technology that
is protected by U.S. patents and other intellectual property
rights. Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended for
home and other limited consumer uses only unless otherwise
authorized by Macrovision. Reverse engineering or disassembly is prohibited.
Others
• Compatible with RI Dock for iPod
• A/V Sync Control Function (up to 100 ms)
• 40 AM/FM Presets
• 1/4-inch phone jack
• Aluminum Front Panel, Volume and Input Selector
Knob
• Adjustable display brightness
6
Contents
Overview
Important Safety Instructions .................................... 2
Precautions ............................................................... 3
Supplied Accessories................................................ 5
Introduction ............................................................... 6
Features ................................................................ 6
Disc Notes............................................................. 8
Before Using the DVD receiver ............................... 11
Installing the Batteries ......................................... 11
Using the Remote Controller ............................... 11
Front & Rear Panels................................................ 12
Front Panel.......................................................... 12
Display................................................................. 13
Rear Panel .......................................................... 14
Remote Controller ............................................... 15
Connections
Connecting the DVD receiver.................................. 17
Placing the Speakers .......................................... 17
Connecting Your Speakers ................................. 17
Connecting Antenna............................................ 19
AV Cables & Connectors..................................... 21
Video Output/Video Setting Matrix ...................... 22
Video Signal Flow Chart...................................... 22
Before Making Any Connections ......................... 23
Basic Setup ......................................................... 23
Connecting Your TV (video connection).............. 24
Connecting Other AV Component....................... 25
Connecting an RI Dock ....................................... 26
Digital Audio Connection ..................................... 26
Connecting your HDTV or AV component
with an HDMI connection.................................. 27
Connecting the Power/Turning
on the DVD receiver ............................................. 28
Getting Started and Setting up
Initial Setup ............................................................. 29
First Time Setup .................................................. 29
HDMI and Progressive Settings .............................. 30
Setting the HDMI ................................................. 30
Selecting Progressive or Interlaced..................... 30
Basic Operations
Understanding Common Operations....................... 31
Adjusting the Volume .......................................... 31
Selecting the Input Source .................................. 31
Using Headphones.............................................. 31
Muting the DVD receiver ..................................... 32
Using the Sleep Timer......................................... 32
Adjusting Subwoofer Level.................................. 32
Playing Discs........................................................... 33
Starting, Pausing & Stopping Playback............... 33
Select Next & Previous track/chapter.................. 34
Fast Forward & Reverse ..................................... 35
Forward Frame-by-Frame Playback.................... 35
Navigating DVD & VCD Disc Menus ................... 36
Navigating CDs & Super Audio CDs ................... 36
Navigating MP3, WMA & DivX Discs .................. 37
Viewing a Slideshow of JPEG Images ................ 38
Listening to the Radio ............................................. 39
Using the Tuner................................................... 39
Presetting AM/FM Stations.................................. 40
Using RDS (European models only) ................... 41
Using the Listening Modes...................................... 42
Selecting Listening Modes .................................. 42
About the Listening Modes.................................. 42
Playback Techniques
Advanced Playback................................................. 44
Selecting Chapters/Titles/Tracks/Folders by
Number .............................................................44
Searching by Time............................................... 45
Repeat Playback ................................................. 46
A-B Repeat Playback .......................................... 46
Random Playback ............................................... 47
Memory Playback ................................................ 48
Last Memory........................................................ 49
Zooming............................................................... 50
Selecting Camera Angles .................................... 50
Selecting Soundtracks......................................... 51
Selecting Subtitles ............................................... 51
Advanced Operations
Disc and Input Information ...................................... 52
Displaying Information ......................................... 52
Controlling Other Components................................ 53
Controlling a TV connected
to the DVD receiver........................................... 53
Controlling an Apple iPod in RI Dock connected
to the DVD receiver........................................... 54
Detailed Settings
Configuring the DVD receiver.................................. 55
Setup Menu ......................................................... 55
DVD Onscreen Setup Menus .................................. 58
Using the Onscreen Setup Menus....................... 59
Picture Menu ....................................................... 60
Audio Menu ......................................................... 62
Language Menu................................................... 63
Display Menu....................................................... 65
Operation Setting Menu....................................... 66
Miscellaneous information
Additional information.............................................. 68
Resetting the receiver.......................................... 68
DVD-Video regions.............................................. 68
Disc Content Organization................................... 68
Glossary ..................................................................69
Troubleshooting....................................................... 71
Power .................................................................. 71
Audio ................................................................... 71
Video ................................................................... 72
Tuner ................................................................... 73
Remote Controller ............................................... 73
Disc Playback ...................................................... 73
Connection with External Devices ....................... 74
Others.................................................................. 74
HDMI Status Mode ..............................................75
Specifications .......................................................... 76
Remote Control Codes List
The end of this manual
7
Introduction—Continued
Disc Notes
Supported Discs
The DVD receiver supports the following discs.
Disc Logo Format or file type
DVD-Video
DVD-Aud io DVD-Audio
Super Audio
CD
*2
DVD-R
DVD-RW
Video CD Including PBC
Audio CD
CD-R
CD-RW
*2
*3
*2
*2
*1
Super Audio CD (single
layer, dual layer, hybrid)
DVD-Video, MP3, WMA,
JPEG
DVD-Video, MP3, WMA,
JPEG
PCM
Audio CD, MP3, WMA,
JPEG, DivX
Audio CD, MP3, WMA,
JPEG
• The DVD receiver does not support disc types not
listed.
• The DVD receiver supports 8 cm and 12 cm discs.
• Don’t use discs with an unusual shape, such as those
shown below, because you may damage the DVD
receiver.
• Don’t use discs that have residue from adhesive tape,
rental discs with peeling labels, or discs with custommade labels or stickers. Doing so may damage the
DVD receiver and you may not be able to remove the
disc properly.
About playing copy-controlled CDs
Some copy-controlled CDs may not conform to official
CD standards. They are special discs and may not play
on the DVD receiver.
Function Support
The following icons are used throughout this manual to
indicate which functions can be used with the various
disc formats and file types.
Icon Disc format or file type
DVD-V
DVD-A
DVD-Video
DVD -Audio
JPEG CD JPEG
– DVD+R/RW –
The DVD receiver supports DVD+R/RW discs
recorded in the following formats:
• Discs recorded in DVD-Video mode.
• Discs recorded in ISO 9660 Level 2 or Joliet
format containing MP3, WMA, or JPEG files.
*1 The DVD receiver’s region number is printed on the rear panel.
If you attempt to play a disc intended for another region, the
message appears onscreen.
*2 MP3, WMA, and JPEG files are supported on discs recorded in
ISO 9660 Level 2 or Joliet format. (See “MP3/WMA/JPEG
Compatibility” on page 9 for more details.) However, some
CD-R, CD-RW, DVD-R, and DVD-RW discs may not work
properly for any of the following reasons: incomplete disc
finalization, disc burner charac teristics, disc characteristics, the
disc is damaged or dirty, the disc contains only a small amount
of data. Discs that contain different types of files, JPEG, MP3,
WMA, DivX, and so on, are not supported. See the manual supplied with your disc burner for more information. Condensation or dirt on the optical pickup lens can also affect playback.
*3 Some audio CDs feature copy protection that doesn’t conform
to the official CD standard. Since these are nonstandard discs,
they may not play properly in the DVD receiver.
8
SACD
VCD
CD
MP3
WMA
JPEG
DivX
Super Audio CD
Video CD
Audio CD
MP3 file
WMA file
JPEG file
®
DivX
About this Manual
This manual explains how to use all of the DVD
receiver’s functions. Although the DVD standard offers
many special features, not all discs use them all, so
depending on the disc being played, the DVD receiver
may not respond to certain functions. See your disc’s
sleeve notes for supported features.
When you attempt to use a DVD feature that is
not available, this logo may appear onscreen,
indicating that the feature is not supported by
the current disc or by the DVD receiver.
Introduction—Continued
MP3/WMA/JPEG Compatibility
• The DVD receiver can play/display MP3, WMA, and
JPEG files recorded on CD-R, CD-RW, DVD-R,
DVD-RW, DVD+R and DVD+RW discs.
• Discs must be in ISO 9660 Level 2 or Joliet format
(folders can be up to eight levels deep). Music files
recorded on discs that use the HFS (hierarchical file
system) cannot be played.
• Discs must be finalized.
• The DVD receiver can only recognize the first session
on multisession discs.
• You can determine the order in which the DVD
receiver plays/displays your MP3/WMA songs and
JPEG pictures by prefixing file and folder names with
a three-digit number. For example 001.Root,
002.Folder, and so on, and 001.Track.mp3,
002.Track.mp3, and so on.
•
Only the first eight characters of folder and track names
(excluding the filename extension) are displayed.
• The folder numbered “001” appears as “ROOT” in the
Disc Navigator.
• The DVD receiver supports up to 255 folders and up
to 255 files per folder.
• If you try to play an incompatible file, the message
“This format cannot be played.” appears on the display.
■ MP3
• MP3 files must be MPEG1 Audio Layer 3 format,
44.1 or 48 kHz, fixed bit-rate.
• MP3 files must have a “.mp3” or “.MP3” filename
extension.
• Variable bit-rates (VBR) from 32 kbps to 320 kbps are
supported. (Playing times may display incorrectly
with VBR.)
Microsoft Corporation. WMA content can be encoded
by using Windows Media
®
Player version 7/7.1 or 8.
About DivX
DivX is a compressed digital video format created by the
DivX® video codec from DivXNetworks, Inc. This
receiver can play DivX video files burned on CD-R
discs. When naming files on a disc prior to burning, keep
in mind that by default they will be played in alphabetical order.
DivX video compatibility
• Official DivX® Certified product.
• Plays all versions of DivX
6) with standard playback of DivX® media files).
®
DivX
disc compatibility with this receiver is limited as
follows:
Playable discs
File system ISO9660 Level 1, 2, or Joliet
File name
Total number of
folders
Total number of
files
CD-R
CD-RW not recommended
A file name should be in alphabet
and numerals only, and must incorporate “AVI” extension.
e.g. “*****.AVI”
Less than 255
Less than 255
®
video (including DivX
®
■ WMA
• WMA files must have the copyright option turned off.
• Sampling rates 44.1/48 kHz are supported.
• Variable bit-rates (VBR) from 48 kbps to 192 kbps
(44.1 kHz) and 128 kbps to 192 kbps (48 kHz) are
supported. (Playing times may display incorrectly
with VBR.)
• WMA files must have a “.wma” or “.WMA” filename
extension.
■ JPEG
• JPEG files must have a “.jpg” or “.JPG” filename
extension.
• JPEG files must be less than 5 megabytes in size.
• JPEG files up to 5,700 x 3,800 pixels are supported.
About WMA
WMA is an acronym for Windows Media Audio and
refers to an audio compression technology developed by
9
Introduction—Continued
Handling Discs
• Never touch the underside of a disc. Always hold discs
by the edge, as shown.
Underside
• Never attach adhesive tape or sticky labels to discs.
Cleaning Discs
• For best results, keep your discs clean. Fingerprints
and dust can affect the sound and picture quality and
should be removed as follows. Using a clean soft
cloth, wipe from the center outwards, as shown. Never
wipe in a circular direction.
Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material
without permission.
DVD-Video discs are copy-protected, and any recordings made from these discs will be distorted.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use
of this copyright-protection technology must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
✔
• To remove stubborn dust or dirt, wipe the disc with a
damp soft cloth, and then dry it with a dry cloth.
• Never use solvent-based cleaning fluids, such as thinner or benzine, commercially available cleaners, or
antistatic sprays intended for vinyl records, because
they may damage the disc.
Storing Discs
• Don’t store discs in places subject to direct sunlight, or
near heat sources.
• Don’t store discs in places subject to moisture or dust,
such as in a bathroom or near a humidifier.
• Always store discs in their cases and vertically. Stacking, or putting objects on unprotected discs may cause
warping, scratches, or other damage.
10
Before Using the DVD receiver
Installing the Batteries
To open the battery compartment, press
1
the small hollow and slide off the cover.
Insert the two supplied batteries (AA/R6)
2
in accordance with the polarity diagram
inside the battery compartment.
Put the cover onto the remote controller
3
and slide it shut.
Using the Remote Controller
To use the remote controller, point it at the DVD
receiver’s remote control sensor, as shown below.
Remote control sensor
DVD rece ive r
Approx. 5 m
Notes:
• The remote controller may not work reliably if the
DVD receiver is subjected to bright light, such as
direct sunlight or inverter-type fluorescent lights.
Keep this in mind when installing the DVD receiver.
• If another remote controller of the same type is used in
the same room, or the DVD receiver is installed close
to equipment that uses infrared rays, the remote controller may not work reliably.
• Don’t put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries.
• The remote controller may not work reliably if the
DVD receiver is installed in a rack behind colored
glass doors. Keep this in mind when installing the
DVD receiver.
• The remote controller will not work if there’s an
obstacle between it and the DVD receiver’s remote
control sensor.
Notes:
• If the remote controller doesn’t work reliably, try
replacing both batteries.
• Don’t mix new and old batteries, or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent possible leakage
and corrosion.
• Flat batteries should be removed as soon as possible to
prevent possible leakage and corrosion.
11
Front & Rear Panels
For detailed information, refer to the pages in brackets.
Front Panel
(4 (6(1(2(3 (5(7
STANDBY/ON button [28]
This button is used to set the DVD receiver to On or
Standby.
STANDBY indicator [28]
This indicator lights up when the DVD receiver is in
Standby.
INPUT selector [31] and indicator
This selector is used to select from the following
input sources: DVD, VIDEO 1, VIDEO 2/DOCK,
FM, AM.
Disc tray [33]
Discs are loaded here.
(open/close) button [33]
This button is used to open and close the disc tray.
The input source is automatically set to DVD.
(stop) button [34]
This button is used to stop playback.
(play) button [33]
This button is used to start playback.
The input source is automatically set to DVD.
MASTER VOLUME control [31] and indicator
This control is used to adjust the volume of the
DVD receiver to Min, 1 through 79, Max.
PHONES jack [31]
This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.
(1 PURE AUDIO indicator [42]
This indicator lights up when the Pure Audio listening mode is selected.
(2 PURE AUDIO button [42]
Selects the Pure Audio listening mode.
(3 HDMI button [30]
This button is used to turn HDMI on or off.
(4 HDMI indicator [30]
This indicator lights up when a HDMI signal is
being output.
(5 Remote control sensor [11]
This sensor receives control signals from the remote
controller.
(6 Previous/Next / buttons or TUNING/
PRESET / buttons [34, 39]
The Previous [ ] button is used to select the previous chapter or track. During playback it selects
the beginning of the current track.
The Next [ ] button is used to select the next
chapter or track.
When the AM or FM input source is selected, these
buttons are used to tune the tuner, or select radio
presets.
(7 (pause) button or PRESET/MEMORY
button [33, 35, 40]
This button is used to pause playback. While playback is paused, pressing this button moves the video
forward one frame at a time.
When the AM or FM input source is selected, this
button is used to store the radio presets.
12
Front & Rear Panels—Continued
Display
(1 (2 (3
MUTING indicator
This indicator flashes while the DVD receiver is
muted.
Tuning indicators
AUTO : This indicator lights up when the Auto Tuning mode is selected, and disappears when the Manual Tuning mode is selected.
: This indicator lights up when the DVD
receiver is tuned into a radio station.
FM ST: This indicator lights up when the DVD
receiver is tuned to a stereo FM station.
RDS (European model only): This indicator
lights up when the DVD receiver is tuned to a radio
station that supports RDS (Radio Data System).
Listening mode & format indicators
These indicators show the currently selected listening mode and the format of the playing disc.
Playback mode indicators
MEM: Lights up when memory playback is
selected.
RDM: Lights up when random playback is selected.
REPEAT: Lights up when repeat playback is
selected for all the tracks.
REPEAT 1: Lights up when repeat playback is
selected for a track.
Disc type indicators
These indicators show the type of disc loaded.
Data type indicators
These indicators show the type of data loaded.
Disc operation indicators
These indicators show the status of disc playback.
DIGITAL indicator
This indicator lights up when the digital audio signal input is used.
ANALOG indicator
This indicator lights up when the analog audio signal input is used.
(4
(5
(7
(6
(8
(1 Camera angle indicator
This indicator appears if the DVD-Video disc being
played features multiple camera angles.
(2 SLEEP indicator
This indicator lights up when the Sleep function has
been set.
(3 GROUP indicator
While stopped, the total number of groups on the current DVD-Audio disc is displayed here. During playback, the number of the current group is displayed.
(4 TITLE indicator
During playback, the number of the current title is
displayed.
(5 Message & time area
Time information, such as total time, remaining
time, and so on, is displayed here in hours, minutes,
and seconds. Other messages are also displayed.
(6 CHP indicator
This indicator appears while the number of the current chapter is being displayed.
(7 TRACK indicator
This indicator appears while track numbers are
being displayed. While stopped, the total number of
tracks on the current SACD or audio CD are displayed. During playback, the number of the current
track is displayed.
(8 PRGSV indicator
This indicator appears when progressive video is
being output by the component video output.
(9 TOTAL indicator
This indicator appears while the total number or
total time is being displayed.
(: REMAIN indicator
This indicator appears while the remaining time is
being displayed.
(:(9
13
Front & Rear Panels—Continued
Rear Panel
(1 (2 (3 (5
SPEAKERS [18]
These terminal posts are for connecting your front
speakers.
HDMI IN/OUT [27]
HDMI (High Definition Multimedia Interface) connections carry digital audio and digital video.
The HDMI input is for connecting components with
HDMI outputs. The HDMI output is for connecting
a TV or projector with an HDMI input.
COMPONENT VIDEO OUTPUT [24]
These jacks output component video and can be
connected to an component video input on a TV or
projector.
VIDEO OUTPUT [23]
This RCA connector can be used to connect a TV or
projector with a composite video input.
FM ANTENNA [19]
This jack is for connecting an FM antenna.
AM ANTENNA [19]
These push terminals are for connecting an AM
antenna.
AV CONNECTOR (European model only) [24]
This SCART output can be connected to a TV or
projector with a SCART input. This SCART connector outputs 2-channel stereo audio, composite
video, and RGB video.
SPEAKER IMPEDANCE SELECTOR [18]
This selector is used to select impedances of your
speakers.
If the impedance of any of front speakers is 4 ohms
or more but less than 6, set the speaker impedance
:~16:”.
to “4
OPTICAL DIGITAL AUDIO IN [26]
This optical digital audio input can be connected to
an optical digital audio output on a DVD recorder,
or game console.
This input is assigned for VIDEO 1 INPUT in
default.
(4 (6
If you output audio from this input during
VIDEO 2/DOCK INPUT is selected, you must
change the “Video2 Input” setting to “OPT” from
“Coax” (page 55).
(1 COAXIAL DIGITAL AUDIO IN [26]
This coaxial digital audio input can be connected to
a coaxial digital audio output on a DVD recorder or
game console.
This input is assigned for VIDEO 2/DOCK INPUT
in default.
If you output audio from this input during VIDEO 1
INPUT is selected, you must change the “Video1
Input” setting to “Coax” from “OPT” (page 55).
(2 REMOTE CONTROL [26]
This (Remote Interactive) jack can be connected to an jack on Onkyo RI Dock. The DVD
receiver remote controller can then be used to control the RI Dock. To use , you must make an
analog audio connection (RCA) between the DVD
receiver and the RI Dock, even if they are connected
digitally.
(3 VIDEO 1 INPUT [25]
Here you can connect other video equipment. Input
jacks include composite video and analog audio
input.
(4 VIDEO 2/DOCK INPUT [26]
Here you can connect Onkyo RI DOCK or other
video equipment. Input jacks include composite
video and analog audio input.
(5 SUBWOOFER PRE OUT [18]
A powered subwoofer can be connected here.
(6 AC INLET [28]
The supplied power cord is connected here. The
other of the power cord should be connected to a
suitable wall outlet.
14
Front & Rear Panels—Continued
Remote Controller
(1
(2
(3
(4
(5
(6
(7
(8
(9
(:
)1
)2
STANDBY/ON button* [28]
This button is used to set the DVD receiver to
Standby or turn on.
Don’t turn on the DVD receiver until you’ve completed, and double checked all connections
(pages 23–27).
Number buttons* [44, 45, 66]
These buttons are used to enter title, chapter, and
track numbers and to enter times for locating specific points in time.
CLR button [40, 44, 45, 49]
This button is used to cancel various functions.
TV Control buttons [53]
These buttons are used to control a TV. You must
enter the appropriate remote control code first.
Disc and DVD receiver menu buttons
TOP MENU button* [36, 38]
With DVD discs, this button displays the main
menu. With a JPEG disc, it displays thumbnails of
the images. With a Video CD, it turns PBC on or
off.
MENU button* [36, 38]
This button is used to display a menu on a DVD or
to open the Disc Navigator when using a JPEG disc.
Cursor /// buttons* [36, 55, 59]
These buttons are used to navigate menus.
ENTER button* [36, 55, 59]
This button is used to start playback of the selected
title, chapter, or track, and to confirm settings.
SETUP button [55, 59]
This button is used to open and close the setup
menus.
RETURN button [55]
This button is used to return to the previous display
when changing settings.
15
Front & Rear Panels—Continued
Basic Playback buttons*
Pause button [33, 35]
This button is used to pause playback. While playback is paused, pressing this button moves the video
forward one frame at a time.
Play button [33]
This button is used to start playback.
Stop button [34]
This button is used to stop playback.
Fast Reverse/Fast Forward / buttons
[35]
These buttons are used for fast reverse and fast forward.
Previous/Next / buttons [34]
The Previous [ ] button is used to select the previous chapter or track. During playback it selects
the beginning of the current track.
The Next [ ] button is used to select the next
chapter or track.
Advanced Playback buttons
AUDIO button [51]
This button is used to select foreign language
soundtracks and audio formats (e.g., Dolby Digital
or DTS) on DVD-Video discs.
SUBTITLE button [51]
This button is used to select subtitles on
DVD-Video discs.
ANGLE button [50]
This button is used to select camera angles on
DVD-Video discs.
RANDOM button* [47]
This button is used with the Random function.
REPEAT button* [46]
This button is used to set the Repeat function.
A-B button [46]
This button is used to set the A-B Repeat function.
DISPLAY button [52]
This button is used to display information about the
disc or the current input source. Press it repeatedly
to display more information.
ASPECT/ZOOM button [50, 60]
This button is used to change the view mode. Pressing and holding it for a few seconds selects Zoom
mode.
(1 RESOLUTION button [30]
This button is used to select a video resolution for
the HDMI OUT.
(2 SLEEP button [32]
This button is used with the Sleep function.
(3 INPUT / button [31]
This button is used to select the input sources.
(4 SEARCH button [40, 44, 45]
This button is used to search for titles, chapters,
groups, folders, tracks, and specific points in time.
When the AM or FM input source is selected, you
can tune into AM and FM stations directly by entering the appropriate frequency.
(5 MEMORY button [48]
This button is used with the Memory function.
When the AM or FM input source is selected, this
button is used to store the radio presets.
(6 LAST MEMORY button [49]
This button is used with the Last Memory function
for DVD playback.
(7 MUTING button [32]
This button is used to mute or unmute the DVD
receiver.
(8 VOL / button [31]
This button is used to adjust the volume of the DVD
receiver.
(9 Tuner buttons
TUNING / button [39]
When the AM or FM input source is selected, the
[]/[]
TUNING
PRESET / buttons [40]
When the AM or FM input source is selected, the
PRESET [ ]/[ ] buttons are used to select radio
presets.
buttons are used to tune the tuner.
(: MODE button* [39]
This button is used to select the Auto or Manual
tuning mode.
)1 SUBWOOFER LEVEL button [32]
This button is used to access the Subwoofer Level
menu.
Use the Left and Right [ ]/[ ] buttons to adjust the
volume.
)2 LISTENING MODE button [42]
This button is used to select the listening modes.
For buttons to control an Apple iPod in RI Dock with
*
an RI connection, see page 54.
16
Connecting the DVD receiver
Placing the Speakers
Front Left and Right Speakers
• Place the front left and right speakers symmetrically
and so that the distance from the listening position is
the same.
• When placing speakers, direct the speakers toward the
position of the listener’s ears where the listener sits to
enjoy music or movies.
• Place the two speakers so that the heights of the two
speakers are aligned. The ideal height for the speakers
is the height of the listener’s ears.
TV or screen
FL FR
FL: Front left speaker
FR: Front right speaker
Subwoofer
Using a subwoofer greatly improves the volume level
and sound quality of bass sounds. The subwoofer
effect depends not only on the listening position but
also on the shape of the listening room.
• In general, place the subwoofer in a corner of the room
or at a point 1/3 the width of the room.
• Play a movie or music that contains high quality bass
sounds to determine the subwoofer placement.
Change the subwoofer’s position and check the effect,
then select the position where the bass sounds are best
heard.
Connecting Your Speakers
Speaker Connection Precautions
Read the following before connecting your speakers:
• You can connect speakers with an impedance of
between 4 and 16 ohms. If the impedance of any of the
connected speakers is 4 ohms or more, but less than 6
ohms, be sure to set the speaker impedance to
“4:~16:” (see page 18). If you use speakers with a
lower impedance, and use the DVD receiver at high
volume levels for a long period of time, the built-in
protection circuit may be activated.
• Disconnect the power cord from the wall outlet before
making any connections.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive
(+) terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the
positive and negative wires.
Doing so may damage the
DVD receiver.
• Make sure the metal core of
the wire does not have contact
with the DVD receiver’s rear
panel. Doing so may damage the DVD receiver.
• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the DVD receiver.
• Don’t connect one speaker to several terminals.
1/3 room
length
Corner
17
Connecting the DVD receiver—Continued
Connecting the Speaker Cables
Strip about 15 mm of insu-
1
lation from the ends of the
speaker cables, and twist
the bare wires tightly, as
shown.
Unscrew the terminal.
2
Fully insert the bare
3
wires.
Screw the terminal tight.
4
The following illustration shows which speaker should
be connected to each pair of terminals.
Front right
speaker
Front left
speaker
15 mm
Speaker Impedance
If the impedance of any of front speakers is 4 ohms or
more but less than 6, set the speaker impedance to
“4:~16:”.
SPEAKER IMPEDANCE
SELECTOR
Use the SPEAKER IMPEDANCE SELECTOR to select speaker impedance.
:~16::
4
Select if the impedance of any of speakers is 4
ohms or more but less than 6.
:~16::
6
Select if the impedances of all speakers are
between 6 and 16 ohms.
Note:
Change of the settings may be required for some speakers (see page 55).
Connecting a Powered Subwoofer
Using a suitable cable, connect the DVD receiver’s SUBWOOFER PRE OUT to an input on your powered subwoofer, as shown.
Powered
subwoofer
LINE INPUT
LINE INPUT
18
Connecting the DVD receiver—Continued
Connecting Antenna
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The DVD receiver won’t pick up any radio signals without any antenna connected, so you must connect the
antenna to use the tuner.
AM antenna push terminals
FM antenna connector
Connecting the Indoor FM Antenna
The supplied indoor FM antenna is for indoor use only.
Attach the FM antenna, as shown.
1
Insert the plug fully
into the jack.
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
Assemble the AM loop antenna, inserting
1
the tabs into the base, as shown.
Connect both wires of the AM loop
2
antenna to the AM antenna push terminals, as shown.
The antenna connection is polarity sensitive. Connect the black wire to the ground terminal ( ).
Connect the other wire to the other terminal.
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
Push Insert wire Release
Once your DVD receiver is ready for use, you’ll
need to tune into an FM radio station and adjust
the position of the FM antenna to achieve the best
possible reception.
Use thumbtacks or something similar to
2
fix the FM antenna into position.
Thumbtacks, etc.
Caution: Be careful that you don’t injure yourself
when using thumbtacks.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 20).
Black
Once your DVD receiver is ready for use, you’ll
need to tune into an AM radio station and adjust
the position of the AM antenna to achieve the best
possible reception.
Keep the antenna as far away as possible from
your DVD receiver, TV, speaker cables, and
power cords.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 20).
19
Connecting the DVD receiver—Continued
Connecting an Outdoor FM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available outdoor FM antenna instead.
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock hazards.
Connecting an Outdoor AM Antenna
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoor AM antenna can be used
in addition to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
AM loop antenna
Black
White
Outdoor AM antennas work best when installed outside
horizontally, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as
shown.
TV/FM antenna splitter
To DVD receiver To TV (or VCR)
20
Connecting the DVD receiver—Continued
AV Cables & Connectors
Video
Cable Jack Description
HDMI
Y
//
C
B
P
B
C
R
P
R
Component
video
Y
C
B
P
B
R
P/ /
R
C
HDMI connections can carry uncompressed, standard or high definition digital video and digital
audio, for the best picture and sound quality.
Component video separates the luminance (Y) and
color difference signals (PR, PB), providing the best
picture quality. Some TV manufacturers label their
component video inputs differently.
Composite
video
(supplied)
Scart
(European
model only)
Audio
Optical digital
Coaxial digital
Analog
Composite video can be found on virtually all TVs,
VCRs, and video equipment.
SCART connections carry analog audio and video
(composite, RGB) all in one cable.
Cable Jack Description
Optical digital audio connections provide better
OPTICAL
audio quality than analog connections.
Coaxial digital audio connections provide better
audio quality than analog connections.
RCA analog audio connectors can be found on virtually all AV components.
21
Connecting the DVD receiver—Continued
Video Output/Video Setting Matrix
The following matrix shows how the video outputs work in relation to the various video settings.
✓: Output
Setting
HD Resolution (page 30) Progressive Setting (page 30)
Video output
HDMI
Component
Composite ✓
*4
SCART
model only)
*1 No picture will be output from other than HDMI when you connect the TV that the native resolution is “720p” or “1080i”.
*2 If your TV doesn’t support progressive scanning, you’ll get no picture.
*3 If your TV doesn’t support the “HD Resolution” settings of “720p” and “1080i”, you’ll get no picture.
*4 With the “SCART Output Setting”, you can choose “RGB” or composite video for the SCART output. However, when HDMI is
(European
on, you cannot select “RGB”. Also, when “RGB” is selected, nothing will be output by the component video output (see page 62).
Auto
✓✓✓
*1
✓
*1
*1
✓
Video Signal Flow Chart
Video input signals flow through the DVD receiver as shown.
HDMI input pass through HDMI output signals as it is.
HDMI Output Setting (page 29, 30)
On (default) Off
480p / 576p
(default)
*2
✓
720p, 1080i Progressive Interlace
*3
No output ✓
No output No output
*2
✓
✓ No output ✓✓
✓ No output ✓✓
Set top box, VCR, DVD recorder, etc.
VIDEO 1 VIDEO 2/DOCK
HDMI
HDMI IN V IN V IN
HDMI ComponentComposite SCART
Composite
TV, projector, etc.
Composite
DVD
AV CONNECTORVIDEO OUT COMPONENT OUTHDMI OUT
22
Connecting the DVD receiver—Continued
Before Making Any Connections
• Read the manuals supplied with your AV components.
• Don’t connect the power cord until you’ve completed
all audio and video connections.
RCA AV Connection Color Coding
RCA AV connections are usually color coded: red,
white, and yellow. Use red plugs to connect right-channel audio inputs and outputs (typically labeled “R”). Use
white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to
connect composite video inputs and outputs.
Right (red)
Left (white)
(Yellow)
Analog audio
Composite video (Supplied)
Right (red)
Left (white)
(Yellow)
Basic Setup
The setup described here is a basic setup that allows you to play discs using just the cables supplied with the receiver.
• Push each plug in all the way to
make a good connection (loose
Right!
connections can cause noise or
malfunctions).
• To prevent interference, keep
audio and video cables away from
Wrong!
power cords and speaker cables.
Optical Digital Jacks
The DVD receiver’s optical digital connectors have a
shutter-type cover that opens when an optical plug is
inserted, and closes when it’s removed. Push the plug in
all the way.
Caution: To prevent shutter damage, hold the optical
plug straight when inserting and removing.
Video cable
(Supplied)
This receiver is equipped with copy protection technology. Do not connect this receiver to your TV via a
VCR using Video cable, as the picture from this
receiver will not appear properly on your TV. (This
receiver may also not be compatible with some combination TV/VCRs for the same reason; refer to the
manufacturer for more information.)
TV
VIDEO IN
To power outlet
Powe r cord
(Supplied)
1. Connect the VIDEO OUTPUT jack to the com-
posite video input on your TV.
Use the supplied Video cable (RCA), connecting the
yellow plug to the video output.
See the following page if you want to use other cable
for the video connection.
2. Connect the supplied AC power cord to the AC
INLET, then plug into a power outlet.
23
Connecting the DVD receiver—Continued
Connecting Your TV
(video connection)
• Connect the DVD receiver directly to your TV. If you
connect the DVD receiver through a VCR, TV/VCR
combination, or video selector, the picture may be distorted because DVD-Video discs are usually copy protected.
Using Component Video
You can use the component video output instead of the
standard video out jack to connect this receiver to your
TV (or other equipment).
This will provide better quality picture than composite
video.
This jack cannot output the signal from composite
video input.
• Use a component video cable (not supplied) to connect the COMPONENT VIDEO OUTPUT jacks to a
component video input on your TV (or monitor).
If you connect the component video output to a TV or
another component that doesn’t support progressive
scanning, be sure to turn off HDMI (see page 30).
You can set the component video output to Progressive
or Interlaced (see page 30).
Using SCART (European model only)
If your TV has a SCART-type AV input, you can use a
SCART cable to connect this receiver to your TV. This
type of connection carries both the sound and the picture.
• Use a SCART cable (not supplied) to connect the AV
CONNECTOR to an AV input on your TV.
TV
SCART
TV
YPB PR
COMPONENT
VIDEO IN
Compatibility of this unit with progressive-scan TVs.
This receiver is compatible with progressive video
Macro Vision System Copy Guard.
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR
625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE “STANDARD DEFINITION” OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p
DVD RECEIVER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.
This connector can output composite video, or RGB
video. The default setting is composite, which should
work with all TVs. Consult the manual that came with
your TV to see if you can use one of the higher quality
settings. See page 62 for how to change the video output.
24
Connecting the DVD receiver—Continued
Connecting Other AV Component
You can use an AV cable to connect VIDEO 1 INPUT L/R or V jack to your AV component such as a set top box, VCR,
and DVD recorder.
Connect your AV component’s analog audio and Video output jack to the DVD receiver’s VIDEO 1 INPUT L/R or V
jack.
OUT
LR
AUDIO
OUT
VIDEO
Set top box,
VCR, DVD
Recorder
Note:
You can also use optical/coaxial digital cable instead of the audio cable (see page 26).
25
Connecting the DVD receiver—Continued
Connecting an RI Dock
■
iPod with video or RI Dock with the OSD mode
Connect your RI Dock’s analog audio output jacks
and Video output jack to the DVD receiver’s
VIDEO 2/DOCK INPUT L/R jacks and V jack.
Connect the RI Dock with an cable. (Onkyo
DS-A1X/A2/A2X hookup shown below.)
■ iPod without video
Connect your RI Dock’s analog audio output jacks to
the DVD receiver’s VIDEO 2/DOCK INPUT jacks.
Connect the RI Dock with an cable. (Onkyo
DS-A1 hookup shown below.)
Notes:
• Set the RI Dock’s RI MODE switch to HDD or HDD/DOCK.
• Press the INPUT [ ]/[ ] buttons to select “VIDEO2/DOCK”.
• Refer to the RI Dock’s instruction manual.
Digital Audio Connection
You can use optical/coaxial digital cable instead of the audio cable when connecting with other AV components.
Connect your AV component’s digital audio output jack to corresponding COAXIAL or OPTICAL DIGITAL AUDIO
IN jack of the DVD receiver.
You must assign that jack to an input (see page 57).
Notes:
• Optical digital audio input is assigned for VIDEO 1
INPUT in default.
If you output audio from this input during VIDEO 2/
DOCK INPUT is selected, you must change the
“Video2 Input” setting to “OPT” from “Coax”.
• Coaxial digital audio input is assigned for VIDEO 2/
DOCK INPUT in default.
If you output audio from this input during VIDEO 1
INPUT is selected, you must change the “Video1
Input” setting to “Coax” from “OPT”.
Set top box,
VCR, DVD
Recorder
COAXIALOPTICAL
Connect one
or the other
VIDEO
OUT
26
Loading...