Onkyo DR-815 User Manual

Contents

Getting Started .......................... 2

DVD receiver

Connections ............................ 16

DR-815

Operations ............................... 25

Instruction Manual

Thank you for purchasing the Onkyo DR-815 DVD receiver. Read this manual carefully before using your new DVD receiver. A good understanding of its features and operation will allow you to achieve optimum performance and enjoyment.

Playing a Disc.......................... 29

Listening to the Radio ........... 42

Enjoying Surround Sound....... 52

Adjusting Sound ..................... 56

Setting Clock and Timer ......... 58

Detailed Settings and

Informations (DVD) .................67

Keep this manual for future reference.

Miscellaneous .........................76

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12.

Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

PORTABLE CART WARNING

S3125A

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons. The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS

OUVRIR

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualiﬁed service personnel under the following conditions: A. When the power-supply cord or plug is dam-

aged,

B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or

water,

D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualiﬁed technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a ﬁre or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a ﬂue-like gap for warm air to escape.

Precautions

1. Recording Copyright —Unless it’s for personal use

only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse —The AC fuse inside the unit is not user-

serviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. Care —Occasionally you should dust the unit all

over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the ﬁnish or remove the panel lettering.

4. Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

Pressing the [STANDBY/ON] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Never Touch this Unit with Wet Hands— Never

handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

6. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit

for a long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm

after prolonged use. This is normal.

• If you do not use this unit for a long time, it may

not work properly the next time you turn it on, so be sure to use it occasionally.

• When you’ve ﬁnished using this unit, remove all

discs and turn off the power.

7. Installing this Unit

• Install this unit in a well-ventilated location.

• Ensure that there’s adequate ventilation all

around this unit, especially if it’s installed in an audio rack. If the ventilation is inadequate, the unit may overheat, leading to malfunction.

• Do not expose this unit to direct sunlight or heat sources, because its internal temperature may rise, shortening the life of the optical pickup.

• Avoid damp and dusty places, and places subject to vibrations from loudspeakers. Never put the unit on top of, or directly above a loudspeaker.

• Install this unit horizontally. Never use it on its side or on a sloping surface, because it may cause a malfunction.

• If you install this unit near a TV, radio, or VCR, the picture and sound quality may be affected. If this occurs, move this unit away from the TV, radio, or VCR.

8. To Obtain a Clear Picture —This unit is a high-

tech, precision device. If the lens on the optical pickup, or the disc drive mechanism becomes dirty or worn, the picture quality may be affected. To maintain the best picture quality, we recommend regular inspection and maintenance (cleaning or worn part replacement) every 1,000 hours of use depending on the operating environment. Contact your Onkyo dealer for details.

9. Moisture Condensation Moisture condensation may damage this unit.

Read the following carefully: Moisture may condense on the lens of the optical pickup, one of the most important parts inside this unit.

• Moisture condensation can occur in the following

situations: – The unit is moved from a cold place to a warm

place.

– A heater is turned on, or cold air from an air

conditioner is hitting the unit.

– In the summer, when this unit is moved from

an air conditioned room to a hot and humid place.

– The unit is used in a humid place.

• Do not use this unit when there’s the possibility

of moisture condensation occurring. Doing so may damage your discs and certain parts inside this unit.

If condensation does occur, remove all discs and leave this unit turned on for two to three hours. By this time, the unit will have warmed up and any condensation will have evaporated.

10. Region Numbers —The DVD standard uses region numbers to control how discs can be played around the world, the world being divided into six regions. This unit will only play DVD discs that match its region number, which can be found on its rear panel

ALL

(e.g., , ).

Precautions —Continued

11. About this Manual —This manual explains how to

use all of this unit’s functions. Although the DVD standard offers many special features, not all discs use them all, so depending on the disc being played, this unit may not respond to certain functions. See the disc’s sleeve notes for supported features.

For British models

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualiﬁed service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral Brown: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IMPORTANT

The plug is ﬁtted with an appropriate fuse. If the fuse needs to be replaced, the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug. Check for the ASTA mark or the BSI mark on the body of the fuse. If the power cord’s plug is not suitable for your socket outlets, cut it off and ﬁt a suitable plug. Fit a suitable fuse in the plug.

This unit contains a semiconductor laser system and is classiﬁed as a “CLASS 1 LASER PRODUCT”. So, to use this model properly, read this Instruction Manual carefully. In case of any trouble, please contact the store where you purchased the unit.

To prevent being exposed to the laser beam, do not try to open the enclosure.

CAUTION:

CLASS 1M VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

The label on the right is applied on the rear panel.

1. This unit is a CLASS 1 LASER PRODUCT and employs a laser inside the cabinet.

2. To prevent the laser from being exposed, do not remove the cover. Refer servicing to qualiﬁed personnel.

For European Models

Declaration of Conformity

We,

ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY

declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3.

GROEBENZELL, GERMANY

K. MIYAGI

ONKYO EUROPE ELECTRONICS GmbH

Features

Receiver

• Built-in Dolby Pro Logic II, Dolby Digital and DTS

• On board Theater Dimensional Circuit

• Deep bass adjustable S. Bass feature

• Subwoofer or power ampliﬁer connectable PRE-OUT

terminals allowing 5.1ch playback with add on speakers

• WRAT (Wide Range Ampliﬁer Technology) exploit- ing the broadband potential of next generation media

• VLSC (Vector Linear Shaping Circuitry) on the front left and right channels

• Up to 30 stations memory storable tuner with FM auto preset feature

• Program timer capable of multi settings for both playback and recording

DVD

• Dolby

• DVD-Video / Video CD / Audio CD playback

• CD-R, CD-RW (Video CD, audio CD, MP3/WMA

• DVD-Audio and SACD compatible

• DVD-R (DVD-Video)

• DVD-RW (DVD-Video, VR format)

JPEG)

Digital and DTS

Supplied Accessories

Make sure you have the following accessories:

RC-640S

Remote controller & two batteries (AA/R6)

AM loop antenna x 1

Indoor FM antenna x 1

Others

• Full-function remote controller

*1. Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

*2. “DTS”, “DTS 96/24” and “DTS Digital Out” are trademarks of

DTS, Inc.

*3. Windows Media, and the Win-

dows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.

4. Theater-Dimensional is a trademark of Onkyo Corporation.

Video cable x 1

* In catalogs and on packaging, the letter at the end of the product name indicates the color. Speciﬁcations and operations are the same regardless of color.

Table of Contents

Getting Started

Important Safety Instructions...............................2

Precautions .........................................................3

Features ..............................................................5

Supplied Accessories ..........................................5

Disc Notes ...........................................................8

Remote Controller .............................................10

Installing the Batteries ...................................10

Using the Remote Controller .........................10

Part Names and Functions................................11

Front Panel ....................................................11

Display...........................................................12

Rear Panel.....................................................13

Remote Controller .........................................14

Connections

Connecting Antenna..........................................16

Connecting Speakers ........................................18

Connecting Speakers ....................................18

Speaker Connection Precautions ..................18

AV Cables and Connectors ...............................19

Before Making Any Connections ...................19

AV Cables & Connectors...............................19

Connecting Your TV ..........................................20

Connecting External Devices ............................21

Connecting an Onkyo Stereo Cassette Tape

Deck ...................................................... 21

Connecting an RI Dock (Remote Interactive

Dock) ..................................................... 21

Connection for TV Audio Signal ....................22

Connecting a Subwoofer ...............................22

Connection for Enjoying 5.1ch Playback .......23

Enjoying Home Theater.................................24

Operations

Connecting the Power Cord ..............................25

First Time Setup ............................................25

Turning Off ACCUCLOCK .............................25

Understanding Common Operations.................26

Turning the Unit On and Off ..........................26

Adjusting the Volume.....................................26

Selecting a Source ........................................27

Muting the Sound ..........................................27

Controlling Display Brightness.......................27

Listening through the Headphones................27

Customizing the Source Names........................28

Playing a Disc

Before Starting DVD Playback.......................... 29

Using the On-screen Displays ...................... 29

Setting Up the Player for Your TV................. 29

Setting the Language of This Player’s On-screen

Displays..........................................................30

Playing Discs ....................................................31

Resume and Last Memory............................ 31

Basic Playback Controls ............................... 32

DVD Disc Menus........................................... 32

Video CD PBC menus .................................. 33

Scanning Discs ............................................. 33

Playing in Slow Motion.................................. 34

Frame Advance/Frame Reverse................... 34

Switching Audio Language/Channel............. 35

Switching Subtitles........................................ 35

Switching Camera Angles............................. 35

Zooming the Screen...................................... 35

Browsing Video Content with the Disc Navigator... 36 Browsing WMA, MP3 and JPEG files with the

Disc Navigator........................................ 37

Creating a Program List................................ 38

Searching a Disc........................................... 39

Using Random Play ...................................... 39

Looping a Section of a Disc .......................... 40

Using Repeat Play ........................................ 40

Viewing a JPEG Slideshow........................... 41

Displaying Disc Information .......................... 41

Listening to the Radio

Listening to the Radio....................................... 42

Manually Tuning a FM/AM Broadcast Station........ 42

Adjusting the Antenna................................... 43

Programming FM Stations Automatically – Auto

Preset ......................................................... 44

Programming FM/AM Stations One by One –

Preset Write.......................................... 45

Selecting Preset Stations.............................. 46

Switching the Display Information................. 47

Receiving RDS.............................................. 47

Changing the Preset Channels......................... 48

Tips for Changing the Preset Channels........ 48

Copying a Preset Channel – Preset Copy .... 48

Erasing a Preset Channel – Preset Erase .... 49

Naming Preset Channels.................................. 50

Naming a Preset Channel............................. 50

Entering a Name........................................... 50

Correcting and Erasing a Character ............. 50

Inserting a Character .................................... 51

Erasing the Name Assigned to a Preset

Channel................................................ 51

Inputting Characters from the Remote Controller... 51

Table of Contents —Continued

Enjoying Surround Sound

Enjoying Surround Sound................................. 52

Configuring Subwoofer and Setting Up the

Number of Speakers............................ 52

Setting Distance of Speakers........................ 53

Speaker Level Calibration............................. 53

Enjoying Listening Modes................................. 54

Selecting Listening Mode.............................. 55

Adjusting Sound

Adjusting Sound................................................56

Adjusting Individual Speaker Levels .............56

Emphasizing the Low End Using the Remote

Controller................................................ 56

Using the Late Night Function (Dolby Digital

only) ....................................................... 56

Audio Adjust Function ............................... 57

Setting Clock and Timer

Setting the Clock...............................................58

Setting ACCUCLOCK to Use a Specific Station.... 58

Setting the Clock Manually............................ 59

Checking the Time and the Day of the Week .... 60

To Switch between the 12-hour and 24-hour

Displays................................................ 60

Turning the Current Time Display On or Off

while the Unit is in Standby Mode.......... 60

Using the Timer Functions ................................ 61

About the Once and Every Timers................ 61

Using the Sleep Timer................................... 62

Programming a Once / Every Timer.............. 63

Switching the Timer On and Off.................... 66

Viewing the Timer Settings ...........................66

Detailed Settings and Informations (DVD)

DVD Audio Settings and Video Adjust menus ..... 67

Video Adjust menu ........................................67

Initial Settings menu..........................................68

Using the Initial Settings menu......................68

How to Use Parental Lock.............................71

Additional information........................................73

Screen sizes and disc formats.......................73

Setting the TV system .............................73

Resetting the DVD player ........................74

Titles, chapters and tracks.............................74

DVD-Video regions........................................74

Selecting languages using the language code

list.......................................................... 74

Miscellaneous

Input Source Names and Available Buttons on

Remote Controller ................................. 76

Recording..........................................................78

Troubleshooting.................................................79

Specifications ....................................................82

Disc Notes

Supported Discs

The DVD receiver supports the following discs.

Disc Logo Format or ﬁle type

DVD-Video

DVD-Audio

SACD

DVD-R

DVD-RW

Video CD

Audio CD

CD-R

CD-RW

See page 74 for region information.

DVD-Audio

Super Audio CD (single layer, dual layer, hybrid)

DVD-Video

DVD-Video, VR format

Including PBC

PCM and DTS

Video CD, audio CD, MP3, WMA, JPEG

• Some audio CDs feature copy protection that doesn’t conform to the ofﬁcial CD standard. Since these are nonstandard discs, they may not play properly in the DVD receiver.

• The DVD receiver supports CD-R and CD-RW discs recorded in Video CD format, audio CD format, or ISO 9660 Level 1 or 2 format with MP3, WMA, and JPEG ﬁles. It also supports DVD-R and DVD-RW discs recorded in DVD-Video format. However, some CD-R, CD-RW, DVD-R, and DVD-RW discs may not work properly for any of the following reasons: incomplete disc ﬁnalization, disc burner characteristics, disc characteristics, the disc is damaged or dirty. See the manual supplied with your disc burner for more information. Condensation or dirt on the optical pickup lens can also affect playback.

• The DVD receiver supports 8 cm and 12 cm discs.

• The DVD receiver does not support disc types not

listed. If you load any disc for playback other than listed above, the DVD receiver may cause noise or may not operate properly.

• Don’t use discs with an unusual shape, such as those shown below, because you may damage the DVD receiver.

• Don’t use discs that have residue from adhesive tape, rental discs with peeling labels, or discs with custommade labels or stickers. Doing so may damage the DVD receiver and you may not be able to remove the disc properly.

Discs Made on Personal Computers

Discs made on personal computers, including those of a compatible format, may not work properly in the DVD receiver because of incorrect settings in the disc burning software. Check the manuals supplied with your disc burning software for additional compatibility information.

CD-R/RW compatibility

• Compatible formats: CD-Audio, Video CD, ISO 9660 CD-ROM* containing MP3, WMA or JPEG ﬁles

* ISO 9660 Level 1 or 2 compliant. CD physical format:

Mode1, Mode2 XA Form1. Romeo and Joliet ﬁle systems are both compatible with this player.

• Multi-session playback: No

• Unﬁnalized disc playback: No

DVD-R/RW compatibility

• Compatible formats: DVD-Video, Video Recording (VR)*

* Edit points may not play exactly as edited; screen may go

momentarily blank at edited points.

• Unﬁnalized playback: No

• WMA/MP3/JPEG ﬁle playback on DVD-R/RW: No

Compressed audio compatibility

• Compatible formats: MPEG-1 Audio Layer 3 (MP3), Windows Media Audio (WMA)

• Sampling rates: 32, 44.1 or 48kHz

• Bit-rates: Any (128Kbps or higher recommended)

• VBR (variable bit rate) MP3 playback: No

• VBR WMA playback: No

• WMA lossless encoding compatible: No

• DRM (Digital Rights Management) compatible: Yes

(DRM-protected audio ﬁles will not play in this player.)

• File extensions: .mp3, .wma (these must be used for the player to recognize MP3 and WMA ﬁles – do not use for other ﬁle types)

• File structure: Up to 299 folders; up to 648 folders and ﬁles combined

Disc Notes —Continued

About WMA

WMA is an acronym for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA content can be encoded by using Windows Media dows Media Media

Player for Windows

Player 9 Series.

Player version 7, 7.1, Win-

XP, or Windows

JPEG ﬁle compatibility

• Compatible formats: Baseline JPEG and EXIF 2.2* still image ﬁles up to a resolution of 3072 x 2048.

* File format used by digital still cameras

• Progressive JPEG compatible: No

• File extensions: .jpg (must be used for the player to recognize JPEG ﬁles – do not use for other ﬁle types)

• File structure: Up to 299 folders; up to 648 folders and ﬁles combined

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material without permission.

DVD-Video discs are copy-protected, and any recordings made from these discs will be distorted.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Handling Discs

• Never touch the underside of a disc. Always hold discs by the edge, as shown.

Underside

• Never attach adhesive tape or sticky labels to discs.

Cleaning Discs

• For best results, keep your discs clean. Fingerprints and dust can affect the sound and picture quality and should be removed as follows. Using a clean soft cloth, wipe from the center outwards, as shown. Never wipe in a circular direction.

✔

• To remove stubborn dust or dirt, wipe the disc with a damp soft cloth, and then dry it with a dry cloth.

• Never use solvent-based cleaning ﬂuids, such as thinner or benzine, commercially available cleaners, or antistatic sprays intended for vinyl records, because they may damage the disc.

Storing Discs

• Don’t store discs in places subject to direct sunlight, or near heat sources.

• Don’t store discs in places subject to moisture or dust, such as in a bathroom or near a humidiﬁer.

• Always store discs in their cases and vertically. Stacking, or putting objects on unprotected discs may cause warping, scratches, or other damage.

Remote Controller

Installing the Batteries

To open the battery compartment, press

the small hollow and slide off the cover.

Insert the two supplied batteries (AA/R6)

in accordance with the polarity diagram inside the battery compartment.

Put the cover onto the remote controller

and slide it shut.

Notes:

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.

Using the Remote Controller

To use the remote controller, point it at the DVD receiver’s remote control sensor, as shown below.

Remote control sensor

Approx. 5 m

(16 ft.)

DVD receiver

Notes:

• The remote controller may not work reliably if the DVD receiver is subjected to bright light, such as direct sunlight or inverter-type ﬂuorescent lights. Keep this in mind when installing.

• If another remote controller of the same type is used in the same room, or the DVD receiver is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

• Don’t put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries.

• The remote controller may not work reliably if the DVD receiver is installed in a rack behind colored glass doors. Keep this in mind when installing.

• The remote controller will not work if there’s an obstacle between it and the DVD receiver’s remote control sensor.

Part Names and Functions

Front Panel

The page numbers in parentheses show where you can ﬁnd the main explanation for each item.

Remote control sensor (10)

Receives signals from the remote controller.

INPUT/CURSOR buttons (27, 28, 44, 46, 78)

Enable you to select an input source. These buttons also move the cursor when you input characters.

VOLUME control (26)

Adjusts the volume level.

STANDBY indicator (25)

Lights up in Standby mode.

STANDBY/ON button (31, 60, 65)

Press this button to turn on the power to the unit or place the unit in Standby mode.

PHONES jack (27)

Connect a headphone mini plug here.

DVD disc tray (31)

Place a DVD in the disc tray.

LISTENING MODE button (55)

Use this button to select the listening modes.

S.BASS button (56)

Use this button to adjust the low end bass range.

/ buttons (32)

Fast-forward or reverse the track being played. These buttons also move the cursor when you input characters.

DISPLAY button (41, 47, 50)

Each time you press this button, the information on the display changes. This button also enables you to select the input character type.

5867 JK M NOPQRL9

Display

TIMER button (59, 62, 63, 66)

Press this button to enable the timer function or set current time.

MULTI JOG dial (28, 32, 33, 44, 46)

Turn the dial to select a programmed station, playback track or groups. It also assists you to choose an edit type, and to select characters when you enter characters. Press it to conﬁrm the current setting.

YES/MODE button (42, 45, 50)

Press this button to conﬁrm the displayed settings for playback and other editing operations.

EDIT/NO/CLEAR button (28, 44-45, 48-50)

Enables you to adjust settings for playback and select editing operations. It also cancels the displayed setting.

DVD button (32)

Starts DVD playback. When you press this button during playback, the unit enters Pause mode.

DVD button (32)

Stops DVD playback.

DVD button (31)

Ejects a loaded DVD.

Part Names and Functions —Continued

Display

12 43576

DIGITAL

MUTING

S.BASS

AUTO

TIMER

GROUP TITLE CHP TRACK DISC TOTAL REMAIN

1 2 3 4

SLEEP

9J8MK L N O P

S.BASS indicator

This indicator lights up when the super bass is selected.

MUTING indicator

This indicator ﬂashes while the DVD receiver is muted.

Tuning indicators AUTO: This indicator lights up when the Auto Tun-

ing mode is selected, and disappears when the Manual Tuning mode is selected.

This indicator lights up when the DVD

receiver is tuned into a radio station.

FM ST: This indicator lights up when the DVD

receiver is tuned to a stereo FM station.

RDS: This indicator lights up when the DVD

receiver is tuned to a radio station that supports RDS (Radio Data System).

Listening mode & format indicators

These indicators show the currently selected listening mode and the format of the playing disc.

Playback mode indicators

MEM: Lights up when memory playback is

selected.

RDM: Lights up when random playback is selected. NORMAL: Lights up when normal playback is

selected.

REPEAT: Lights up when repeat playback is

selected for all the tracks.

REPEAT 1: Lights up when repeat playback is

selected for a track.

Disc type indicators

These indicators show the type of disc loaded.

DVD operation indicators

These indicators show the status of DVD playback.

Camera angle indicator

This indicator appears if the DVD-Video disc being played features multiple camera angles.

DTS AAC PCM DVD - AUDIO D V D

T - D DSP STEREO VCD SACD

FM ST RDS

MEM RDM TRACK NAMENORMAL REPEAT 1

SLEEP indicator

This indicator lights up when the Sleep function has been set.

TIMER indicators

These indicators show the status of the timers.

Numbers 1-4: Lights up when a timer has been set.

GROUP indicators

This indicator lights up when the Group number is displayed.

TITLE indicator

During playback, the number of the current title is displayed.

Message area

Various information is displayed here, including preset number, tuning frequency, time, volume level, sleep time, mode settings, and so on.

CHP indicator

This indicator appears while the number of the current chapter is being displayed.

TRACK indicators

This indicator lights up when the track number is displayed.

DVD information indicators

The item lights up, which corresponds to the information in the message area.

Lights up when timed recording has been set.

Rear Panel

Part Names and Functions —Continued

1B D

The page numbers in parentheses show where you can ﬁnd the main explanation for each item.

TAPE/HDD IN/OUT (21)

This analog audio input and output are for connecting a recorder with an analog audio input and output (cassette, Mini Disc, etc.). If you want to connect Onkyo RI Dock, connect the RI Dock output with the TAPE/HDD IN terminal.

LINE/TV IN (22)

These terminals are for connecting audio output of external devices such as TV, DVD or turntable with a built-in phono equalizer.

FM ANTENNA (16, 17)

This jack is for connecting an FM antenna.

AM ANTENNA (16,17)

These push terminals are for connecting an AM antenna.

FRONT SPEAKERS (18)

These terminals are for connecting speakers.

AV CONNECTOR (20)

This SCART output can be connected to a TV or projector with a SCART input. This SCART connector outputs composite video, S Video, and RGB video.

VIDEO OUT VIDEO (20)

This RCA connector can be used to connect a TV or projector with a composite video input.

VIDEO OUT S VIDEO OUT (20)

This connector can be used to connect a TV or projector with an S Video input.

See pages 16-23 for connection information.

PRE OUT (22, 23)

These terminals are for connecting a power ampliﬁer.

SUBWOOFER CONTROL

This terminal is provided for future use with Onkyo subwoofer equipped with SUBWOOFER CONTROL terminals. No product is available as of July 2006.

REMOTE CONTROL (21)

This (Remote Interactive) jack can be connected to an jack on another Onkyo AV compo-

nent. The DVD receiver’s remote controller can then be used to control that component. To use ,

you must make an analog audio connection (RCA) between the DVD receiver and the other AV component.

G 8

Part Names and Functions —Continued

Remote Controller

This section describes the role of the individual buttons you use to control the ampliﬁer and the tuner.

2 3

5 6

7 8

9 J

The page numbers in parentheses show where you can ﬁnd the main explanation for each item.

INPUT buttons (27, 42, 44, 46, 78)

Each time you press these buttons, the input source switches.

PRESET / buttons (46)

These buttons select programmed stations.

TUNING / buttons (42)

These buttons tune in a broadcast station or move the cursor when you input characters.

MODE button (42)

This button is used to select the Auto or Manual tuning mode.

Number buttons (46, 51)

Used to name a preset station.

LATE NIGHT button (56)

Switches the dynamic range for playback at minimum volume.

CH SEL button (56)

Selects the speakers.

TEST TONE button (53)

Outputs the test tone.

P Q

R S

T U V

Y Z

DIMMER button (27)

Adjusts the display brightness.

normal dim dimmer

TIMER button (59, 63, 66)

Press this button to enable the timer function or set current time.

RCV SETUP button (52, 57)

Press this button to conﬁgure settings for the DVD receiver.

/ / / /ENTER buttons (52, 53)

These buttons are used to select and adjust settings.

CLOCK button (60)

Press this button to display the current time.

SLEEP button (62)

Used to program the Sleep timer, which turns off the power to the unit at a speciﬁed time.

STANDBY/ON button (26, 65)

Switches between power standby and on.

NAME button (51)

Used to input characters when you give a name to each FM/AM preset channel.

DISPLAY button (47, 51, 53, 60)

Each time you press this button, the information on the display changes. It also selects the character input type.

ENTER button (51)

Press this button to conﬁrm the current setting.

CLEAR button (50)

Cancels the settings, and erases a character.

STEREO/T-D button (55)

Switches over between Stereo Sound and Theater Dimensional Surround.

ALL CH STEREO button (55)

This button is used to select the All Ch Stereo listening mode. It is operable when center/surround speakers are connected.

LISTENING MODE button (55)

Selects the listening mode.

S.BASS button (56)

Adjusts the low end bass range.

VOLUME +/– buttons (26)

Adjust the volume level.

MUTING button (27)

Lowers the volume level temporarily.

RETURN button (52, 53)

This button is used to return to the previously selected menu.

Remote Controller

This section describes the role of the individual buttons you use to control DVD and CD.

1 2 3

P 4 5 6 7

S 8

9 J

U N

The page numbers in parentheses show where you can ﬁnd the main explanation for each item.

MODE button (38, 39, 40)

Switches the play mode while DVD is loaded.

MEMORY button (38)

This button is used with the memory playback function, which allows you to create a custom playlist of titles, chapters, or tracks.

RANDOM button (39)

This button is used with the random playback function.

REPEAT button (40)

Repeats playback or RI Dock playback.

Pause button (32, 34, 41)

This button is used to pause playback.

Previous/Next / buttons (32, 33, 41)

The Previous button is used to select the previous chapter or track. During playback it selects the beginning of the current chapter or track. The Next button is used to select the next chapter or track.

Part Names and Functions —Continued

/ buttons (32, 33, 34)

Fast-forward or reverse being played.

AUDIO button (35)

This button is used to select foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS) on DVD-Video discs. For Video CDs you can select left-channel, rightchannel, or stereo.

ANGLE button (35)

This button is used to select camera angles on DVD-Video discs.

SUBTITLE button (35)

This button is used to select subtitles on DVD-Video discs.

TOP MENU button (32)

This button is used to display the top menu on a DVD-Video disc.

ENTER button (29, 32, 68, 71, 72)

This button is used to start playback of the selected title, chapter, or track, and to conﬁrm settings.

RETURN button (29, 32, 33)

This button is used to return to the main menu without saving your changes.

Arrow [ ]/[ ]/[ ]/[ ] buttons (29, 32, 41,

68, 74)

These buttons are used to select items on the onscreen setup menus.

DISPLAY button (41)

Each time you press this button, the information on the display changes.

Number buttons and CLEAR button (32, 38, 71, 72)

You can select a track or sort tracks for Memory playback by using the number buttons. You can cancel the setting by pressing the CLEAR.

Stop button (32)

This button is used to stop playback.

Play button (31-34)

This button is used to start playback.

ZOOM button (35, 41)

This button is used with the Zoom function.

MENU button (32, 41)

This button is used to display the menu on a DVD-Video disc or to open the Disc Navigator when using a Video CD, audio CD, WMA/MP3/ JPEG disc, or VR format DVD-RW disc.

DVD SETUP button (29, 36, 37, 67, 68)

This button is used to access the DVD player’s onscreen setup menus.

Connecting Antenna

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.

The DVD receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

AM antenna push terminals

FM antenna connector

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

Attach the FM antenna, as shown.

Insert the plug fully into the jack.

Once your DVD receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use only.

Assemble the AM loop antenna, inserting

the tabs into the base, as shown.

Connect both wires of the AM loop

antenna to the AM push terminals, as shown.

(The antenna’s wires are not polarity sensitive, so they can be connected either way around.)

Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.

Push Insert wire Release

Use thumbtacks or something similar to

ﬁx the FM antenna into position.

Thumbtacks, etc.

Caution: Be careful that you don’t injure yourself

when using thumbtacks.

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 17).

Once your DVD receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.

Keep the antenna as far away as possible from your DVD receiver, TV, speaker cables, and power cords.

If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 17).

■

Connecting Antenna —Continued

Connecting an Outdoor FM Antenna

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

Notes:

• Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft.

• For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter.

• Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc.

• For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment.

• Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

Using a TV/FM Antenna Splitter

It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown.

Connecting an Outdoor AM Antenna

If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.

Outdoor antenna

Insulated antenna cable

AM loop antenna

Outdoor AM antennas work best when installed outside horizontally, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected.

Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

TV/FM antenna splitter

To DVD receiver To TV (or VCR)

Connecting Speakers

• Connect the right speaker to the DVD receiver’s right (R) SPEAKERS terminals. Connect the left speaker to the DVD receiver’s left (L) SPEAKERS terminal.

• Connect the positive (+) terminal on each speaker to the corresponding positive (+) terminal on the DVD receiver. Connect the negative (–) terminal on each speaker to the corresponding negative (–) terminal on the DVD receiver. Use the red wires to connect the positive (+) terminal.

Strip 3/8" (10 mm) of insu-

lation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

While pressing the lever, insert

the wire into the hole, and then release the lever.

Make sure that the terminals are gripping the bare wires, not the insulation.

The following illustration shows which speaker should be connected to each pair of terminals.

3/8" (10 mm)

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of

ohms or higher . If you use speakers with a lower

impedance, and use the ampliﬁer at high volume levels for a long period of time, the built-in protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals to only positive (+) terminals, and negative (–) terminals to only negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires. Doing so may damage the AV receiver.

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

Front right

speaker

Front left

speaker

AV Cables and Connectors

Before Making Any Connections

• Read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed

all audio and video connections.

• Do not place objects on the unit as they may interfere with proper ventilation.

RCA AV Connection Color Coding

RCA AV connections are usually color coded: red, white, and yellow. Use red plugs to connect right-channel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.

AV Cables & Connectors

Right (red) Left (white)

(Yellow)

• Push each plug in all the way to make a good connection (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

Analog audio

Composite video (Supplied)

Right (red) Left (white)

(Yellow)

Right!

Wrong!

Video

S Video

Composite video

Scart

Audio

Analog

S Video provides better picture quality than composite video.

Composite video can be found on virtually all TVs, VCRs, and video equipment.

SCART connections carry video (composite, S Video, RGB) all in one cable.

RCA analog audio connectors can be found on virtually all AV components.

Connecting Your TV

Connect the DVD receiver to the TV directly. If you connect the DVD receiver to a VCR, TV/VCR combination, or video selector, the playback picture may be distorted as DVD videos are copy protected.

Using Video

Use the supplied video cable (RCA) and connect the VIDEO OUT to the VIDEO input on your TV.

Video cable (Supplied)

Using S Video

If your TV (or other equipment) has an S Video input, you can use this instead of the standard (composite) output for a better quality picture.

• Use an S Video cable (not supplied) to connect the S VIDEO OUTPUT to an S Video input on your TV (or monitor or AV receiver).

Line up the small triangle above the jack with the same mark on the plug before plugging in.

Using SCART

If your TV has a SCART-type AV input, you can use a SCART cable to connect the DVD receiver to your TV.

• Use a SCART cable (not supplied) to connect the AVCONNECTOR to an AV input on your TV.

TVSCART

This connector can output composite video, S-Video, or RGB video. The default setting is composite, which

should work with all TVs. Consult the manual that came with your TV to see if you can use one of the higher quality settings. See page 68 for how to change the video output.

S-Video cable (Not supplied)

Connecting External Devices

Connect the white plugs of the audio cables to the L jacks and connect the red plugs of the audio cables to the R jacks. Tip: The source names appearing in the display can be customized for the connected component (see page 28).

Connecting an Onkyo Stereo Cassette Tape Deck

The following diagram illustrates how to connect an optional Onkyo stereo cassette tape deck. Connect the DVD receiver’s TAPE/HDD OUT jacks to the tape deck’s INPUT (REC) jacks, and the DVD receiver’s TAPE/HDD IN jacks to the tape deck’s OUTPUT (PLAY) jacks.

DVD receiver’s rear panel

red

Onkyo stereo cassette

tape deck rear panel

INPUT OUTPUT

(REC) (PLAY)

REMOTE

CONTROL

: Signal ﬂow

white

red

RCA/phono audio cable

cable supplied with the Onkyo stereo cassette tape deck

redwhite whitered

Use either socket

What does connecting an Onkyo stereo cassette tape deck using an cable enable you to do?

• You can control a connected Onkyo stereo cassette tape deck using the supplied remote controller. You also need to connect the RCA/phono audio cable.

• To operate the system, the source name in the display should be TAPE. (Since the default source name in the display is TAPE, you do not need to change the setting. See page 28 for further information.)

• When the connected Onkyo stereo cassette tape deck plays back, the Input Selector on the DVD receiver is automatically switched to TAPE.

Connecting an RI Dock (Remote Interactive Dock)

The following diagram illustrates how to connect the Onkyo RI Dock which is sold separately. Connect the TAPE/HDD IN jacks on the DVD receiver to the AUDIO OUT jacks on the RI Dock.

DVD receiver’s rear panel

white

red

RCA/phono audio cable

----

AUDIO OUT DC INS VIDEO OUT

: Signal ﬂow

red

white

cable

Jacks on the RI Dock’s rear panel may differ depending on the model.

The jack connection enables you to use the following functions:

• You can control a connected Onkyo RI Dock using the supplied remote controller. You also need to connect the RCA/ phono audio cable.

• When an RI Dock and other -compatible devices are connected with the DVD receiver, you must also interconnect the terminals between the two external devices.

• You need to change the source name in the display to HDD. (The default source name in the display is TAPE. See page 28 for further information.) If the RI Dock has a MODE switch, you must set the switch to HDD.

• When the connected Onkyo RI Dock plays back, the input selector on the DVD receiver is automatically switched to HDD.

Connecting External Devices —Continued

Connection for TV Audio Signal

Connect the LINE IN terminal on the DVD receiver and an audio output terminal on TV.

DVD receiver’s rear panel

white

red

: Signal ﬂow

RCA/phono audio cable

red

white

Connecting a Subwoofer

The DVD receiver has a SUBWOOFER PRE OUT jack. Connect an active subwoofer (a subwoofer that contains an ampliﬁer).

DVD receiver

Active subwoofer (with a built-in ampliﬁer)

: Signal ﬂow

Note:

If you want to connect any passive subwoofer, you must connect at ﬁrst a power ampliﬁer with the DVD receiver, and then connect a subwoofer to the power ampliﬁer.

Connecting External Devices —Continued

Connection for Enjoying 5.1ch Playback

You can connect a center speaker and a left and a right surround speakers by adding on a power (main) ampliﬁer. In addition to this conﬁguration, you can add on a subwoofer to enjoy the 5.1ch surround sound. (See page 22.) Once you have completed the connection, make sure to conﬁgure the settings for speakers, described on page 52, so that

you can enjoy your favorite surround mode.

DVD receiver

LINE INPUT

Active (Powered) subwoofer

speaker

CENTER

MAIN IN

OUTPUT

SURROUND LEFT

MAIN IN

OUTPUT

SURROUND RIGHT

MAIN IN

OUTPUT

Power ampliﬁer

Center speakerFront right

Front left speaker

Surround right speaker

Surround left speaker

Connecting External Devices —Continued

Enjoying Home Theater

The DVD receiver provides multi-channel playback with its theater dimensional feature, even under two front speaker conditions.

Certainly, it can provide full 5.1ch playback in combination with an add-on subwoofer, center and surround speakers off the shelf, so that you can enjoy more realistic, movie theater/concert hall-in-the-home sound effect.

With DVDs you can enjoy DTS and Dolby Digital.

Front left and right speakers

These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equidistant from the TV. Angle them inward so as to create a triangle, with the listener at the apex.

Center speaker

This speaker enhances the front left and right speakers, making sound movements distinct and providing a full sound image. In movies it’s used mainly for dialog. Position it close to your TV (preferably on top) facing forward at about ear level, or at the same height as the front left and right speakers.

Subwoofer

The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) channel. The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening position. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third the width of the wall, as shown.

Corner

1/3 wall length

Surround left and right speakers

These speakers are used for precise sound positioning and to add realistic ambience. Position them at the sides of the listener, or slightly behind, about 2–3 feet (60–100 cm) above ear level. Ideally they should be equidistant from the listener.

• For optimum surround playback, set the distance between the listener and the speakers so that the time it takes the sound to reach the listener is same. Also, you need to set each speaker volume level individually in order to balance the volume level between speakers (see pages 52-53).

Connecting the Power Cord

When the power cord is connected to the AC outlet, the

To wall outlet

STANDBY indicator

First Time Setup

The very ﬁrst time you turn on the DVD receiver, the ACCUCLOCK function automatically sets the clock by using the CT (Clock Time) information present in RDS radio broadcasts. While the clock is being set, “Wait” ﬂashes on the display, as shown. It may take up to ﬁve minutes to set the clock.

When the clock has been set, the message “Clock Adjusted” scrolls across the display, then the day and time are displayed for a while, as shown.

DVD receiver enters Standby mode. The STANDBY indicator lights up.

When you want to set the clock using the DVD receiver’s ACCUCLOCK function, the FM antenna needs to be connected for receiving the RDS radio broadcasts. For more information, see page 16.

The ACCUCLOCK function automatically updates the clock daily at 2 A.M., 3 A.M. and 2 P.M. If the clock has not been set correctly, see “Setting ACCUCLOCK to Use a Speciﬁc Station” on page 58 and “Setting

the Clock Manually” on page 59.

Turning Off ACCUCLOCK

If you don’t want ACCUCLOCK to automatically update the clock at 2 A.M., 3 A.M. and 2 P.M. everyday, you can turn it off as follows.

Press TIMER button repeatedly until “Clock” appears on the dis- play, as shown.

Press MULTI JOG.

“*AccuClock*” appears on the display, as shown.

These asterisks appear when the

ACCUCLOCK function is on.

Note:

This operation is not available if time adjustment was not properly performed in the previous section.

To turn off ACCUCLOCK, press YES/MODE.

The asterisks disappear, indicating that the ACCUCLOCK function is off. To turn the ACCUCLOCK function on again, press YES/MODE so that asterisks appear.

Understanding Common Operations

VOLUME

INPUT buttons

STANDBY/ON

STANDBY

indicator

PHONES

jack

Turning the Unit On and Off

Press STANDBY/ON on the unit or on the remote controller.

If you press the same button again, the unit will turn off and enter Standby mode.

The DVD receiver is not completely shutdown in Standby mode.

To completely shut down the DVD receiver, disconnect the power cord from wall outlet.

Tip:

• When you start playing (or turn on the power to) an Onkyo RI Dock, CD recorder or cassette tape deck that is connected to the DVD receiver via an cable and RCA/phono audio cables, the power to the DVD receiver is automatically turned on. Also, if you turn on or off the power to the DVD receiver, the power to such a device is automatically turned on or off (standby).

STANDBY/ ON

INPUT buttons

DIMMER

VOLUME +/–

MUTING

Adjusting the Volume

DVD receiver

Turn VOLUME clockwise to increase the volume or counterclockwise to decrease the volume on the DVD receiver.

Press VOLUME +/– on the remote controller.

Remote

controller

+ 58 hidden pages