COMPONENTS IDENTIFIED BY MARK ON THE
SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE
CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK.
REPLACE THESE COMPONENTS WITH ONKYO
PARTS WHOSE PART NUMBERS APPEAR AS SHOWN
IN THIS MANUAL.
MAKE LEAKAGE-CURRENT OR RESISTANCE
MEASUREMENTS TO DETERMINE THAT EXPOSED
PARTS ARE ACCEPTABLY INSULATED FROM THE
SUPPLY CIRCUIT BEFORE RETURNING THE
APPLIANCE TO THE CUSTOMER.
Page 2
SPECIFICATIONS
DVD Player
Power supplyAC 120 V, 60 Hz
Power consumption16 W
Weight3.6 kg, 7.9 lbs.
External dimensions435 91 314 mm (W/H/D), 17-1/8"
Signal systemStandard NTSC
Regional restriction code1
LaserSemiconductor laser, wavelength 650 nm
Frequency range (digital audio)DVD linear sound:48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
DVD-Audio:192 kHz sampling 4 Hz to 96 kHz
Audio CD:4 Hz to 20 kHz
Signal-to-noise ratio (digital audio)More than 106 dB
Audio dynamic range (digital audio)More than 100 dB
Harmonic distortion (digital audio)Less than 0.005 %
Wow and flutterBelow measurable level (less than ±0.001 % (W.PEAK))
Operating conditionsTemperature: 5 C to 35 C, Operation status: Horizontal
3-9/16"
DPS-7.2
12-3/8"
Outputs
Video output
S-video output
Component video output
Audio output (digital output Optical)
Audio output (digital output Coaxial)0.5 V (p-p), 75 , pin jack 1
Audio output (analog audio)
Audio output (5.1 channel analog audio)
Specifications and features are subject to change without notice.
1.0 V (p-p), 75 , negative sync., pin jack 2
(Y) 1.0 V (p-p), 75 , negative sync., Mini DIN 4-pin 2
(C) 0.286 V (p-p), 75
(Y) 1.0 V (p-p), 75 , negative sync., pin jack 2
B
)/(PR) 0.7 V (p-p), 75
(P
Optical connecter 2
2.0 V (rms), 470 , pin jack (L, R) 2
2.0 V (rms), 470 , pin jack (FRONT L, FRONT R, CENTER, SURR L,
SURR R, SUB WOOFER)
1
Page 3
SERVICE PROCEDURES-1
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs a laser. Therefore, be sure to follow
carefully the instructions below when servicing.
WARNING!!
SERVICE WARNING : DO NOT APPROACH THE
LASER EXIT WITH THE EYE TOO CLOSELY.
IN CASE IT IS NECESSARY TO CONFIRM LASER
BEAM EMISSION, BE SURE TO OBSERVE FROM
A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE
OPTICAL PICKUP BLOCK.
WARNING
Laser Diode Properties
CD
Wavelength:
Laser output:
650 nm
0.43 mW
DVD
Wavelength:
Laser output:
780 nm
0.14 mW
DPS-7.2
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
LASER WARNING
This unit contains a semiconductor laser system and is classified
as a "CLASS 1 LASER PRODUCT". So, to use this model
properly, read this Instruction Manual carefully. In case of any
trouble, please contact the store where you purchased the unit.
To prevent being exposed to the laser beam, do not try to open
the enclosure.
CAUTION:
VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK
FAILED OR DEFEATED. DO NOT STARE INTO BEAM.
CAUTION:
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MA
HAZARDOUS RADIATION EXPOSURE.
Y RESULT IN
SERVICE PROCEDURE
1. Replacing the fuses
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
The label on the right
is applied on the rear
panel except for USA
and Canadian
models.
1. This unit is a CLASS 1 LASER PRODUCT and employs a
laser inside the cabinet.
2. To prevent the laser from being exposed, do not remove
the cover. Refer servicing to qualified personnel.
LASER BEAM CAUTION LABEL
"CLASS 1 LASER
PRODUCT"
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
This symbol located near the fuse indicates that the
fuse used is show operating type, For continued protection against
fire hazard, replace with same type fuse , For fuse rating, refer to
the marking adjest to the symbol.
Ce symbole indique que le fusible utilise est e lent.
Pour une protection permanente, n'utiliser que des fusibles de meme
type. Ce demier est indique la qu le present symbol est apposre.
REF. NO.
F1
PART NO.
252147 or1.6A-TSC or
DESCRIPTION
2522521.6A-T/UL-ST2
2. Safety-check out
After correcting the original service problem perform the
following safety check before releasing the set to the customer
Connect the insulating-resistance tester between the plug of
power supply cord and terminal GND on the back panel.
Specifications: More than 10M ohm at 500V
24150022DB-VPB302, Main PC board ass'y
24801010DB-VLD301-006, DVD mechanism ass'y
24840149ADB-VAC301, adapter(L)
24840150ADB-VAC302, adapter(R)
1H465515-1GNADIS-7215-1G, Display PC board ass'y
1H465516-1GNADIS-7216-1G, Control switch PC board ass'y
1H465518-1GNASW-7218-1G, Power switch PC board ass'y
1H465520-1GNAPS-7220-1G, AC inlet PC board ass'y
1H465515-1GNAETC-7221-1G, RS-232C connector PC board ass'y
1H465515-1BNAETC-7222-1B, Holder PC board ass'y
24150020ANGPS-0020-120V, Power supply unit
NOTE: THE COMPONENTS IDENTIFIED BY MARK ARE
CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK.
REPLACE ONLY WITH PART NUMBER SPECIFIED.
ALL CAPACITORS ARE IN pF/50WV UNLESS OTHERWISE NOTED.
EX) 030 3pF 330 33pF 331 330pF
.
ALL RESISTORS ARE IN OHMS 1/4WATTS
.
THE THICK LINES ON PC BOARD ARE THE PRINTING SIDE OF THE PARTS.
EX)PRINTING SIDE
.
CIRCUIT IS SUBJECT TO CHANGE FOR IMPROVEMENT.
WITH PART
NUMBER SPECIFIED.
ARECRITICALFORSAFETY.
MARKBY
ARE IN F/WV.
u
)
333 0.033uF
UNLESS OTHERWISE NOTED.
5
Page 12
R749
R750
820
1K
S713
S714
R735
820
S703
R742
820
S711
S715
MEMORY
R736
1K
S704
RETURN
R743
1K
R737
1.8K
DISPLAY
R744
1.8K
REPEAT
S702
SETUP
PLAY
S710
R753
NC
232SI
RI
LT1
VCOFF
GND
-27V
E+5V
FLAC1
VCOFF
-27V 18
E+5V 17
GND1 16
FLAC1 19
ARE CRITICAL FOR SAFETY.
DCVOLTAGE.
u
RESET
100
R754
GND
RI
LT1_1
RESET
RI 12
LT1 13
GND2 14
VCOFF 15
to NAAR-7224
P701
RESET 11
(NO INPUT SIGNAL)
R738
3.9K
DOWN
S705
PON
232RE
232BU
100
R751
R756
PON
232BU_1
232RE_1
PON 9
232RE 10
S706
R745
3.9K
XRDY
100
XRDY
232BU 8
JL771A
UP
R059
232SI
100
R757
232SI_1
232SI 6
XRDY 7
OPERATION SWITCH PC BOARD
U2
R771
R772
1.8K
3.9K
OFF
S721
S722
CIRCUIT
P731
XSCK
XSCK
SCK 1
DIMMER
STANDBY
R041
0
RN1407
orKRC107S
ENTER
7
6
5
4
3
2
1
U7
NAVD-7221
S731
NPS-115-S673
R739
10K
S707
R746
10K
0
SO
SO
SO 5
JL771B
OPEN
DOWN
ENTER
RIGHT
SI
232SO
232SCK
100
R758
SI_1
232SO
232SCK
SI 3
232SCK 4
VIDEO
S708
UP
LEFT
232SO 2
470
470
R774
R773
S723
D721
D722
STANDBY
Q721
VIDEO CIRCUIT_OFF
Q722
RN1407
orKRC107S
CURSOR
RS-232C CONNECTOR
PC BOARD
REQ
SCK
BUSY
SDATAIN
SDATAOUT
R352 47
R355 47
R354 47
R353 47
SI 10
SO 9
NC12
REQ13
RXD15
SCK11
BUSY14
Q351 MPD789071MC
TXD16
PORT218
PORT319
PORT420
PORT521
PORT622
PORT117
RXD_FL
TXD_FL
RTS_FL
47
47
R360
47
R361
R362
R359
47
1011
Q352
R356 47
VDD 8
VSS 7
PORT723
PORT824
U11
CN2
X351
5.00MHz
R351
1M
RESET
47
R357
X1 6
X2 5
IC 3
RESET 4
PORT1026
PORT1127
PORT1228
PORT925
C351
1/50
MPD4721GS
POWER SUPPLY UNIT
NGPS-0020
F1
1.6A 120V
M+5V
GND1
GND2
GND3
SW+3.3V
to NAAR-7224
P352A
SCK
RESET
SDATAOUT
R358
PORT16 2
PORT1329
PORT1430PORT15 1
C352
1/50
123456789
GNDM
SW+5V
SW+12V
to NAAR-7224
P901
P352B
REQ
BUSY
GND
EV+5V
SDATAIN
C360
100/6.3
C361
104Z
EVER+5V
L351
BK1608LM182-T
GND0
EVER+5V
AC INLET PC BOARD
U6
NAPS-7220
P982B
P982
CN1
-27V
FLAC2
FLAC1
POWER_ON
U4
THIS SYMBOL LOCATED NEAR THE FUSE INDICATES
THAT THE FUSE USED IS SLOW OPERATING TYPE
FOR CONTINUED PROTECTION AGAINST FIRE
HAZARD,REPLACE WITH SAME TYPE FUSE. FOR FUSE
RATING REFER TO THE MARKING ADJACENT TO THE SYMBOL
CE SYMBOLE INDIQUE QUE LE FUSIBLE UTLISE EST
E LENT. POUR UNE PROTECTION PERMANENTE,N'UTILISER
QUE DES FUSIBLES DE MEME TYPE. CE DARNIER EST
INDIQUE LA QU LE PRESENT SYMBOL EST APPOSE.
CAUTION
FOR CONTINUED PROTECTION
AGAINST FIRE HAZARD, REPLACE
ONLY WITH FUSE OF SAME TYPE
VA
AND RATING INDICATED.
ATTENTION
AFIN D'ASSURER UNE PROTECTION
PERMANENTE CONTRE LES RISQUES
D'INCENDIE, REMPLACER UNIQUEMENT
VA
PAR UN FUSIBLE DE MEME TYPE
ET CALIBRATION COMME INDIQUE.
ALL CAPACITORS ARE IN pF/50WV UNLESS OTHERWISE NOTED.
EX) 030 3pF 330 33pF 331 330pF
.
ALL RESISTORS ARE IN OHMS 1/4WATTS
.
THE THICK LINES ON PC BOARD ARE THE PRINTING SIDE OF THE PARTS.
EX)PRINTING SIDE
.
CIRCUIT IS SUBJECT TO CHANGE FOR IMPROVEMENT.
WITH PART
R747
R748
390
470
S712
R733
390
S701
390
S709
R752
232BU
SRESET
S713
RANDOM
R734
470
S702
MENU
R741
470
S710
STOP
NC
R753
232SI
FLAC2
FLAC1
CLEAR
T.MENU
R0560R740
PAUSE
NC
R755
232RE
P701B
NC 21
FLAC2 20
SRESET 22
MARKBY
NUMBER SPECIFIED.
ARE IN F/WV.
)
333 0.033uF
UNLESS OTHERWISE NOTED.
R749
R750
820
1K
S714
R735
820
S703
R742
820
S711
S715
MEMORY
R736
1K
S704
RETURN
R743
1K
R737
1.8K
S705
DISPLAY
R744
1.8K
REPEAT
SETUP
PLAY
NC
RI
LT1
232RE
VCOFF
GND
-27V
E+5V
VCOFF
-27V 18
E+5V 17
GND1 16
FLAC1 19
ARE CRITICAL FOR SAFETY.
DCVOLTAGE.
u
RESET
100
R751
R754
GND
RI
LT1_1
RESET
232RE_1
RI 12
LT1 13
GND2 14
VCOFF 15
to NAAR-7224
P701
RESET 11
(NO INPUT SIGNAL)
DOWN
PON
100
PON
232RE 10
R738
3.9K
S706
R745
3.9K
XRDY
232BU
100
R756
XRDY
232BU_1
PON 9
232BU 8
JL771A
UP
R059
0
SO
232SI
100
R757
SO
232SI_1
232SI 6
XRDY 7
JL771B
R739
10K
S707
R746
10K
232SCK
232SCK
SO 5
232SCK 4
OPEN
DOWN
ENTER
RIGHT
SI
232SO
100
R758
SI_1
232SO
SI 3
VIDEO
CIRCUIT
S708
UP
LEFT
XSCK
XSCK
SCK 1
232SO 2
OFF
P731
R771
1.8K
S721
DIMMER
orKRC107S
7
6
5
4
3
2
1
R772
3.9K
S722
STANDBY
R041
Q721
0
RN1407
ENTER
CURSOR
S731
NPS-115-S673
U7
NAVD-7221
470
470
R774
R773
S723
D721
D722
STANDBY
VIDEO CIRCUIT_OFF
Q722
RN1407
orKRC107S
CN2
RS-232C CONNECTOR
PC BOARD
X351
5.00MHz
REQ
SCK
BUSY
SDATAIN
SDATAOUT
R352 47
R356 47
R355 47
R354 47
R353 47
SI 10
SO 9
NC12
REQ13
RXD15
SCK11
VDD 8
PORT319
PORT420
PORT521
PORT622
PORT723
47
R362
1011
Q352
121314151617181920
VSS 7
PORT824
MPD4721GS
BUSY14
Q351 MPD789071MC
TXD16
PORT117
RXD_FL
TXD_FL
RTS_FL
47
R359
R360
47
R361
PORT218
47
U11
R351
1M
RESET
R357
X1 6
X2 5
RESET 4
PORT1026
PORT1127
PORT925
C351
1/50
C354
POWER SUPPLY UNIT
NGPS-0020
F1
1.6A 120V
GND1
GND2
GND3
SW+3.3V
to NAAR-7224
P352A
SCK
RESET
SDATAOUT
R358
47
IC 3
PORT16 2
PORT1228
PORT1329
PORT1430PORT15 1
C352
1/50
1/50
123456789
C353
GNDM
SW+5V
SW+12V
to NAAR-7224
P901
P352B
REQ
BUSY
GND
EV+5V
SDATAIN
C360
100/6.3
C361
104Z
EVER+5V
L351
BK1608LM182-T
1/50
M+5V
GND0
AC INLET PC BOARD
U6
NAPS-7220
P982B
P982
CN1
-27V
FLAC2
FLAC1
EVER+5V
POWER_ON
U4
THIS SYMBOL LOCATED NEAR THE FUSE INDICATES
THAT THE FUSE USED IS SLOW OPERATING TYPE
FOR CONTINUED PROTECTION AGAINST FIRE
HAZARD,REPLACE WITH SAME TYPE FUSE. FOR FUSE
RATING REFER TO THE MARKING ADJACENT TO THE SYMBOL
CE SYMBOLE INDIQUE QUE LE FUSIBLE UTLISE EST
E LENT. POUR UNE PROTECTION PERMANENTE,N'UTILISER
QUE DES FUSIBLES DE MEME TYPE. CE DARNIER EST
INDIQUE LA QU LE PRESENT SYMBOL EST APPOSE.
CAUTION
FOR CONTINUED PROTECTION
AGAINST FIRE HAZARD, REPLACE
ONLY WITH FUSE OF SAME TYPE
VA
AND RATING INDICATED.
ATTENTION
AFIN D'ASSURER UNE PROTECTION
PERMANENTE CONTRE LES RISQUES
D'INCENDIE, REMPLACER UNIQUEMENT
VA
PAR UN FUSIBLE DE MEME TYPE
ET CALIBRATION COMME INDIQUE.
Power supply, +5VOutput pin of sampling rate 192 LED. control.
Ground pinOutput pin of sampling rate 96 LED control.
Main clock input pin (5MHz)Output pin of Play LED control.
Main clock input pin (5MHz)Output pin of Stop LED control.
Ground pinOutput pin of Open/ close LED control.
Reset pin of microprocessorNot used
Output pin of the clock for the communication with the system microcomputer,
and the writing the data to flash ROM
Input pin of the data for the communication with the system microcomputer,
and the writing the data to flash ROM
Output pin of the data for the communication with the system microcomputer,
and the writing the data to flash ROM
Output pin of the XRDY signal for the communication with the system microcomputer.
Output pin of Power ON control signal for
Output pin of reset signal for system microcomputer.
Not used
Not used
Input pin of remote control signal from remote sensor.
Input pin of LT data for
Output pin of video circuit control signal.
Ground pin for D/A converter.
Input pin for initializing set. (Analog signal)Power supply pin (+5V)
Input pin for the key operation of the unit.FIP control pin to connect pull down resistor
Input pin for the key operation of the unit.
Input pin for the key operation of the unit.
Ground pin
Power supply pin of D/A converter, +5V
Power supply, +5V
Input pin of system control signal (RI).
Output pin of system control signal (RI).
Input pin of REQ signal from microprocessor for RS-232C driver.
Input pin of BUSY signal from microprocessor for RS-232C driver
Input pin of SI signal from microprocessor for RS-232C driver
Input pin of SCK signal from microprocessor for RS-232C driver
Input pin of SO soignal from microprocessor for RS-232C driver
Input pin for test mode.
Output pin of reset signal to microprocessor of RS-232C driver
Output pin of FL filament on/off control.
Input pin-2 for initializing. (for model select)
Input pin-1 for initializing set. (for model select)
Input pin-0 for initializing set. (for model select)
Output pin of standby LED control .
Output pin of video circuit off LED control.
Output pin for FL segment (P13) control.
Output pin for FL segment (P12) control.
O
O
Output pin for FL segment (P11) control.
Output pin for FL segment (P10) control.
O
O
Output pin for FL segment (P9) control.
O
Output pin for FL segment (P8) control.
Output pin for FL segment (P7) control.
O
Output pin for FL segment (P6) control.
O
Output pin for FL segment (P5) control.
O
Output pin for FL segment (P4) control.
O
Output pin for FL segment (P3) control.
O
Output pin for FL segment (P2) control.
O
Output pin for FL segment (P1) control.
O
Output pin for FL grid (G14) control.
O
Output pin for FL grid (G13) control.
O
O
Output pin for FL grid (G12) control.
Output pin for FL grid (G11) control.
O
O
Output pin for FL grid (G10) control.
O
Output pin for FL grid (G9) control.
Output pin for FL grid (G8) control.
O
Output pin for FL grid (G7) control.
O
Output pin for FL grid (G6) control.
O
Output pin for FL grid (G5) control.
O
Output pin for FL grid (G4) control.
O
Output pin for FL grid (G3) control.
O
Output pin for FL grid (G2) control.
O
Output pin for FL grid (G1) control.
O
DPS-7.2
DPS-7.2
Page 26
DISASSEMBLING PROCEDURES-1
1. Optical pick-up are parts which are easy to receive damage with static electricity.
Therefore, in case reassembly mechanism, take the measures against static electricity.
2. The number of ( ) in the explanatory note and in the figure shows Ref. No. of the exploded view.
How to remove the DVD mechanism from chassis
DPS-7.2
1
Remove the top cover
Begin to pull the tray by rotating the gear pulley (14)
2
clockwise.
bottom view
14
How to disassembling the DVD mechanism
Remove the screw and remove the bridge (19).
1
19
Remove the tray panel.
3
tray panel
Remove the four screws which is fixing the dvd
4
mechanism to the chassis, and remove the
mechanism from chassis.
Remove the tray by pressing down the stopper
3
SW lever (17).
screw
Begin to pull the tray by rotating the gear pulley (14)
2
clockwise.
stopper
tray
Set the pick short switch to short side.
4
[NOTE]
Do not disconnect the FFC and wire before doing
this work.
short
open
Page 27
DISASSEMBLING PROCEDURES-2
How to disassembling the DVD mechanism
Disconnect the three FFCs and the wire from the
5
main board.
Remove the traverse unit by pressing down
7
the four stoppers.
DPS-7.2
stopper
main board
wire
FFC
FFC
FFC
stopper
Remove the two screws which is fixing the main board
6
to the mechanism, and remove the main board.
How to reassembling the DVD mechanism
1. To reassemble each mechanism, reverse the applicable "disassemble procedures".
76
1
Notes in each process
1. Attachment of tray.
Insert it after matching the triangle mark of the
loading base and the position of pin on the drive cam
2. Set the pickup short switch.
Set the pick short switch to open side.
[NOTE]
Do not set the switch to open side before doing
connect the FFC and wire to main board.
stopper
stopper
traverse unit
pin
triangle mark
short
Replacement of DVD main board
After replacement of the DVD main board (DB-VPB302) should do the following work.
3. Set the ID number
The necessity of inputting ID data into the unit.
Refer to "Setting the ID number and ID data" of "UPGRADE FIRMWARE" about the method of input ID data.
2. Set the region code
It is unnecessary.
Unit is power on, the region code will be set up automatically.
1. Setup of the firmware
Firmware already exists in the ma inboard.
Be sure to check the version of the firmware.
Refer to "
UPGRADE FIRMWARE"
open
Page 28
DISASSEMBLING PROCEDURES-3
Replacement of DVD mechanism
The display label of the ID number is stuck on the upper part of the DVD mechanism.
ID number needs to be displayed absolutely.
In case replacement DVD mechanism, do the following work absolutely.
1. Stick on the mechanism after replacement the ID label stuck on the DVD mechanism before exchange.
2. When the work which you restick cannot be performed easily, you may post and stick the ID number
on the blank level (Part No.29362727).
Before replace
DPS-7.2
After replace
Restick
Copy the ID number
In this case, the bar code
is unnecessary.
XXXXXXXXX
Stick
Page 29
UPGRADE FIRMWARE-1
Prepares for upgrade firmware
DPS-7.2
ID DATA DISC (DB-VPB302)
Part No. 0R117
It is used for the input of ID data.
INTERFACE JIG
Part No. GGF1348
RS-232C Cable (Straight type Cable)
When using GGF1348
REMOTE CONTROLLER for UPGRADE
Part No. 24140451S
It is remote control of the exclusive use for inputting ID data.
Can not the input of ID data by remote controller attached to the unit.
Part No. 0J13
or
When using 0J13
D-Sub 25pin
(Female type)
Flexible flat cable
Part No.:GGD1231 or 0F001
Video cable
or
D-Sub 9pin
(Female type)
D-Sub 9pin
(Male type)
PC (Personal computer)
D-Sub 9pin
(Male type)
Monitor TV
Page 30
UPGRADE FIRMWARE-2
Connections
Rear panel view
DPS-7.2
Monitor TV
PC
(Personal computer)
P
Y
CH1
CH2
COMPONENT
Video in
VIDEO OUTPUT
P
B
R
RS-232
VIDEO
S VIDEO
ANALOG OUTPUT
CH 2
FRONT
CH 1
L
R
INTERFACE JIG
Part No.GGF1348
SURR
SUB
WOOFER
OPTICAL
COAXIAL
DIGITAL OUTPUT
CENTER
Flexible flat cable
25P
REMOTE
CONTROL
Connect to
CN1
Connect to
CN2
AC INLET
DO NOT
connect the mains
lead at this time
INTERFACE JIG
Part No.0J13
9P
RS-232C Cable
To PC
Prepare the file required for rewriting of the firmware.
Build the folder to C drive of the hard disk of PC,
and put in the file required for the folder.
The required file
NOTE: This is one example.
1. ok_down.exe
Rewriting tools
2. down.bat
Rewriting tools
3. b1ck1048.sz0
Firmware program
The file name changes with versions of the firmware.
Page 31
UPGRADE FIRMWARE-3
Pre programming the remote controller
Before using remote control for upgrade firmware, it is necessary to carry out the following operation.
DPS-7.2
1. Set the DVD/TV switch to TV
DVDTV
2. While holding down the STANDBY button
on the Remote controller that you want to
program, press the ENTER button, and
then release both button.
3. 1 key is pushed, it continues within 20 seconds,
and 0 key is pushed after that.
4. The complete of the setting of remote control.
The order of work
In the case of
upgrade firmware
ON
TV
ON / STANDBY
AUDIO SUBTITLE
ANGLE
COND. M
-
CH
+
VOL
ENTER
-
VOL
VCR
DOWN UPFRFF
23
1
456
789
SEARCH
0
10
B
TV
2
3
1
STANDBY
LAST MDIMMER DISPLAY
TOP MENU
TV/
PAUSE
+
RANDOM REPEAT A-B
DVD
In the case of
replace of the DVD main board
OPEN
/CLOSE
MENU
+
CH
SETUPRETURN
STEP/ SLOW
+
-
FUNCTION M
CLEAR
PROGRAM
KEY
Check the firmware
Check the ID number
Download the firmware
Setting the ID number and data
Check the ID number
Check the firmware
Check of general operation
Replace of the DVD main board
Setting the ID number and data
Check the ID number
Check the firmware
Check of general operation
Page 32
UPGRADE FIRMWARE-4
Check the firmware
1. Press the SETUP key
2. Operate the CURSOR switch to make up the Setup menu mode are selected on monitor TV.
3. Press the DISPLAY button
The region and FW version information will appear on the monitor TV.
DPS-7.2
About ID number and ID data input
It is necessary to set up an individual number (ID number and ID data) for every player in the
DVD audio correspondence player.
The guarantee of operation becomes impossible if this ID number and ID data are not set up correctly.
It is the following case that the input of ID number is required.
1. After download of the data to the flash ROM of the unit.
2. When displayed on FL display as "No ID Number "after turning ON the power supply of the unit.
3. When displayed on FL display as "No ID DATA".
Check ID number
The input of ID number is needed by the work of rewriting of the farmware.
Make the note by checking ID number of the set with the following procedure first.
ID number is displayed also on the DVD mechanism upper part.
See the display, when you cannot check ID number by the following method.
1. Check the connecting the unit to PC and monitor TV.
2. Switch ON the power of unit.
3. Check that the disk is not contained in the unit.
4. Press and hold down CLEAR button, then press the KEY button of remote controller.
5. Press the VOL+ button.
6
TVDVD
TVDVD
Setting TV position
Setting TV position
ANGLE
STANDBY
AUDIOSUBTITLE
COND. M
LAST MDIMMER DISPLAY
TOP MENU
-
CH
+
VOL
ENTER
-
VOL
TV/
VCR
PAUSE
DOWN UPFR FF
STEP/ SLOW
23
1
456
789
+
10
RANDOM REPEAT A-B
DVD
FUNCTION M
SEARCH
0
PROGRAM
B
TV
TV Monitor
MENU
+
CH
SETUPRETURN
5
[Player's ID Number Setting]
ID Number
[000000001]
FL Display
000000001
compare
+
-
CLEAR
KEY
4
>
*********
<CLEAR> Exit
Input ID Number !
Set-up ID number is displayed.
It is displayed also on FL display.
This ID number is recorded
in the memo.
6. Press the B button, and check mode is ended.
Page 33
UPGRADE FIRMWARE-5
Download procedures
[NOTES]
This procedure document supposing using Japanese PC.
The program file name, the folder name, etc. are examples.
1. Start MS-DOS prompt using the start-up menu of PC.
Windows of MS DOS prompt
DPS-7.2
C: WINDOWS>_
2. Press the
C: >_
3. Press the
by the keyboard.
dvs757fw : The folder name which saves the program file
C: dvs757fw>_
4. Press the
by the keyboard.
b1ck1048.sz0
Enter
Enter
Enter
button, after inputting
: The program fail name
The file name changes with versions of FW.
button, after inputting
button, after inputting
down b1ck1048.sz0
Space
cd..
cd dvs757fw
Space
by the keyboard.
Zero
Page 34
UPGRADE FIRMWARE-6
Download procedures
<English>
Please switch on the power supply after connecting the DVD
player and PC.
For continuing the program, please press the any keys.
DPS-7.2
4. Check that the PC and TV monitor are correctly connected with unit.
5. Check that the disk is not contained in the disc.
6. Turn ON the power supply switch of the unit.
7. Press the Enter key of PC.
8. Press the Enter button, after inputting MO by the keyboard of PC.
Page 35
UPGRADE FIRMWARE-7
Download procedures
9. Press the Enter button, after inputting SZL by the keyboard of PC.
DPS-7.2
FL Display
ROM ERASE
LOADING
The file(b1ck1048.sz0) specified by the command line
is used in this program.
The program is checking the circuit.
The program starts transmission
of the data to unit.
Waiting for from 5 to 10 minutes.
The state which download completed
FL Display
NO ID NUM!
The work of download was completed satisfactory.
Page 36
UPGRADE FIRMWARE-8
Setting the regional code
Not need to set up region code at DPS-7.2.
Because the region code is set up automatically.
Setting the ID number and ID data
DPS-7.2
TV Monitor
No ID Number !!!
Into the input mode of ID number.
1. Press and hold down the CLEAR button,
then press the KEY button
2. Press the VOL+ button.
COND.M
LAST MDIMMERDISPLAY
TOP MENU
CH
TV/
VCR
PAUSE
1
456
789
RANDOM REPEAT A-B
TVDVD
DVD
-
23
0+10
B
TV
MENU
+
CH
+
VOL
ENTER
-
VOL
SETUPRETURN
DOWN UPFR FF
STEP/ SLOW
+
-
FUNCTION M
SEARCH
CLEAR
PROGRAM
KEY
FL display
NO ID NUM!
The program is demanding the input
of ID number.
TV Monitor
[Player's ID Number Setting]
ID Number?
2
> - - - - - - - - -
<CLEAR> Exit
Input ID Number!
If input mode requires a unit, the
input of the number will be attained.
Please input nine-digit ID number in
this state.
ID number is written to the yellow label
also display on the rear panel .
1
Setting TV position
Page 37
UPGRADE FIRMWARE-9
Setting the ID number.
1. Input the ID number recorded before using the number button. (Refer to "Check ID number")
TV Monitor
DPS-7.2
PAUSE
DOWN UPFR FF
STEP/SLOW
+
23
1
Number key
1,2 - - - 8,9,0
456
789
+
10
RANDOM REPEAT A-B
-
FUNCTION M
CLEAR
SEARCH
0
PROGRAM
B
KEY
2. Press the VOL - button.
COND.M
LAST MDIMMER DISPLAY
VOL-
TOP MENU
TV/
PAUSE
-
CH
VCR
VOL
ENTER
MENU
+
CH
+
-
VOL
SETUPRETURN
DOWN UPFRFF
ID data setting
1. Press the open/close button of set and the
tray is pulled out.
2. Load the ID data disc.
3. Press the open/close button and tray is closed.
[Player's ID Number Setting]
ID Number?
> 0 0 0 0 0 0 0 0 1 OK?
<PLAY> Complata Mode
<SEARCH> Enter
Input ID Number !
FL display
[Player's ID Number Setting]
<CLEAR> Exit
Insert the ID Disc !
TV MonitorFL display
[Player's ID Number Setting]
Loading The ID data Disc !
IN ID DATA
If ID number is set up, it will
be in ID data input state from CDR.
RD ID DATA
It becomes such a display
during reading of data from
CDR.
The read-in work of ID data from
[Player's ID Number Setting]
CDR starts automatically.
Loading The ID data Disc !
456
5
789
+
10
RANDOM REPEAT A-B
DVD
4. Check being displayed as "
5. Press the B button of remote controller and setting mode is ended.
6. Put out the disc.
7. Check the ID number.
8. Check the Firmware.
-
FUNCTION M
CLEAR
SEARCH
0
PROGRAM
B
KEY
TV
[Player's ID Number Setting]
Rom Write OK !
<CLEAR> Exit
Rom Write OK"
WR ID DATA
If reading completes ID data
from CDR, next, the writing
of ID data to the flash ROM
of a set will start.
ID DATA OK
If the writing of ID data to a flash
ROM is completed, it will be
displayed as " Rom Write OK! "
Page 38
PACKING PROCEDURES
30
DPS-7.2
33
34
35
15,20
12
31
19
32
2
13
4
Front side
12
1
2
5
PARTS LIST
REF.NO.
1
2
4
5
10
12
13
15
PART NO.DESCRIPTION
29053801ACarton box B MDD1N
29091986Pad AS
29100037-1A Poly bag (650 x 500)
29110071 orTape, SOP-400(CLEAR50MT) or
29110098Tape, W50 3M NO 371
29362933UPC label AS
29110149Tape NO.29
29110161Tape
29365089Warranty card (INTEGRA)
DPS-7.2
10
REF.NO.
20
30
31
32
33
34
35
NOTE: THE COMPONENTS IDENTIFIED BY MARK ARE
CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK.
REPLACE ONLY WITH PART NUMBER SPECIFIED.
PART NO.DESCRIPTION
29343135Instruction manual, E
253297KAWAS-UC-2, Power supply cord
24140451RC-451DV, Remote controller
3010054Battery, UM-3
2010379RCA3P(YWR), Pin cord AS
2010380S Video cord
20102003.5-Mini plug (RI)