One for All 8811 - WO CODE, US240, URC-8810w User Manual

INTRODUCTION

The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning (URC-8811) is designed to operate up to
eight home entertainment devices,including TV,video, and audio
components.The remote control requires four (4) fresh AAA alka­line batteries (not included) and easy programming to control your
devices.For best results,please read and perform all instructions
listed here.Also, keep these instructions for future reference.

FEATURES AND FUNCTIONS

Use the Key Charts (below) to learn how to use the universal features
and functions ofthe One For All 8L Home Theater Upgradeable
Universal Remote Control with Learning (URC-8811).

Key Charts

The LED(red light) blinks to show that
the remote control is working and is
sending signals.

`

Press TV,VCR, DVD,AUX,SAT, CD,CBL,or
RCVR/AMPonce to selec t a desired home
entertainment device to control.

After programming,press HOME THEATER
once to select the home theater mode (see
Using The Home Theater Mode).

Press POWER once to turn on or off the
selected device.

Press MENU once to display your selected
device’s main menu.

Use GUIDEto display your selected
device’s program guide or setup menu.

Use EXITto exit from your selected
device’s guide or menu.

Use INFOto display the current channel
and program information.

Use the cursor keys to move the cursor in
the program guide and menu screens.
Use SELECTto choose options from your
selected device’s menu or guide.

In the CDmode, use SELECTto sel e ct a
compact disc.Use

▲(or ▼) to select the

next(or previous) CD.Use (or ) to
select the next(or previous) track.

In the RCVR/AMPmode, use SELECTto
set the surround sound.Use ▲(or ▼)
to adjust the volumehigher (or lower).
Use (or ) to adjust the balanceleft
(or right).

Use VOL+(or VOL-) to raise (or lower) the
sound volume.

Press MUTE once to turn the sound off
or on.

In TV,VCR, DVD,SAT,and CBLmodes, use
FAVto scan favorite channels and/or all
channels.See Using Channel Scan and
Programming Favorite Channel Scan.

Use CH+(or CH-) to select the next higher
(or lower) channel.

Press PREV once to recall the last-viewed
channel and to page back one screen on
the main menu.

In the CDmode, use PREVto tu rn random
play on or off.

In the RCVR/AMPmode, use PREVto sel e ct
the receiver band.

Use the keypad (1~ 9 and 0) to directly
select channels (for example,009 or 031).

In the RCVR/AMPmode, use the keypad
(1~ 9 and 0) to select audio sources 1
through 10.

Press ENTER once after entering the
channel numbers on some TVs.

In the CDmode, use ENTERto add 10 to
the digit entry (e.g.,ENTER and 7 is 17).

Use TV/VIDto switch the TV’s input to
view TV or video programs.

Use the transport keys to control your
VCR,DVD or CD player,or VOD (Video
On Demand) ifavailable on your cable or
satellite service.

To record a VCR program,press RECtwice.
After programming,press M1~M4 once to

run a desired macro (see Using Macros).
After programming,press L1~ L4 once

to activate a learned function (see
Using Learning Keys).

Use PIPto switch the Picture-In-Picture
feature on or off (ifavai lable on your TV).

Use MOVEto move the window picture
to different positions in the main picture.

Use SWAPto switch images and sound
between the main and window pictures.

Press SLEEP to activate your device’s sleep
timer (not available for all devices).

Use to turn on or off the key backlight.
When this feature is activated,keys will
remain backlight for 5 seconds after the
last key press.

Use SETfor all programming sequences.

INSTALLING BATTERIES

1. On the remote control’s back,push the tab and lift off the
battery cover.

2. Obtain four (4) new (fully-charged) AAA alkaline batteries.
Match the + and – marks on the batteries to the + and – marks
in the battery case,then insert the new batteries.

3. Press the battery cover back into place.The tab should click
when the cover is locked.

4. Test the remote control by first pressing POWERand then any
mode key (e.g.,TV).If batteries are inserted correctly,the LED
(red light) will blink once.

NOTE:When batteries need replacement,the remote control will stop
operating.Remove the old batteries and insert new ones to ensure all of
your programming information is restored.

PROGRAMMING DEVICE CONTROL

The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning is preprogrammed at the factory to operate
an RCA TV and VCR,a Motorola (GI) cable box,an RCA satellite
receiver,a Pioneer CD player,a Toshiba DVD player,a Pioneer audio
receiver/ amplifier,and a One For All home automation device.To
control devices other than the default brands,perform the following
steps;otherwise skip this section:

NOTE:For TV/VCR Combo control,see the next section.

1. Turn on a device (e.g.,VCR or DVD player) and,if applicable,
insert media (e.g.,cassette or disc).

NOTE:Please read steps 2 through 4 completely be fore proceeding.
Highlight or write down the codes and device you wish to program before
starting step 2.

2. On the remote control,press a device key once (i.e., TV,VCR,DVD,
AUX,SAT,CD, CBL,or RCVR/AMP).

NOTE:Use the

AUX

key to program control ofhome automation devices as
well as miscellaneous audio services and video accessories.Alternately,use
the

AUX

key to program control ofa second device type (e.g.,a second VCR;

see “Re-assigning Device Keys”).

3. Press and hold SET until the LED (red light) blinks twice,then
release SET.

4. Use the Manufacturer’s Codes (on the back) to locate the type of
device and brand name and then enter the first four-digit code
for your device.If performed correc tly,the LEDw i l l blink tw ice.

NOTE:If the

LED

did not blink twice,repeat steps 2 through 4 and try

entering the same code again.

5. Aim the remote controlat the device and press POWER once.The
device should turn of f.If it does not respond,repeat s teps 2
through 5,trying each code for your brand until you find one that
works.If it still does not work,try Searching For Your Code.

NOTE:If the device does not have a

POWER

key,press the (

Play

) key.

6. Repeat steps 1 through 5 for each device you want to control.
For future reference,write down each working device code in the
boxes below:

TVCode:

VCRCode:

DVDCode:

SATCode:

CDCode:

CBLCode:

RCVR/AMPCode:

AUXCode:

Aux.Device Type:_______________________________

PROGRAMMING TV/VCR COMBO CONTROL

Perform the following instructions to control a TV/VCR Combo:

1. Turn on the TV/VCR Combo and insert a video cassette.

NOTE:Please read steps 2 through 4 completely be fore proceeding.
Highlight or write down the codes and device you wish to program before
starting step 2.

2. On the remote control,press VCR.

3. Press and hold SET until the LED(red light) blinks twice, then
release SET.

4. Use the Setup Codes For TV/VCR Combos(on the back) to locate
the brand name and then enter the first four-digit code for your
device.If performed correctly,the LEDwill blink twice.

NOTE:If the

LED

did not blink twice,repeat steps 2 through 4 and try

entering the same code again.

5. Aim the remote controlat the device and press POWER once.It
should turn off.If the device does not respond,repeat steps 2
through 5,trying each code for your brand until you find one that
works.If it still does not work,try Searching For Your Code.

NOTE:If the device does not have a

POWER

key,press the (

Play

) key.

6. If you’ve located a setup code that works,but it has a separate TV
code,you’ll also need to program it into the remote control to
access volume control as follows:

a. Press TV once. The LED (red light) will blink twice.
b. Enter the TV code for your TV/VCR Combo.If correct,the

LEDwill blink twice.

NOTE:For VCR/TV Combos programmed with separate TV codes,
TV volume is controlled by pressing

VCR

first and then TV.After that,use

VOL+

(or

VOL-

) to raise (or lower) the TV volume.For other alternatives on
controlling your volume keys,see the “Changing Volume Lock”or “Using
Keymover”sections.

7. For future reference,write down the working TV/VCR combo
code in the below boxes:

TV/VCRCode:

TVCode (if used):

SEARCHING FOR YOUR CODE

Ifyour device does not respond to the remote control after trying all
codes listed for your brand,or ifyour brand is not listed at all, try
searching for your code.

For example,to search for a code for your TV:

1. On the remote control,press TV once.

2. Press and hold SET until the LED(red light) blinks twice, then
release SET.

3. Enter 9- 9- 1.The LEDwill blink twice.

4. Aim the remote control at the the TV and slowly alternate
between pressing POWERand TV.Stop when the TV turns off.

NOTE:In the search mode,the remote control will send IR codes from its
library to the selected device,starting with the most popular code first.

5. To lock in the code,press and hold SET until the LED blinks
twice,then release SET.

6. To search for the codes ofyour other devices, repeat steps 1
through 5,but substitute the appropriate device key for the
device you are searching for.

CHECKING THE CODES

Ifyou have set up the remote control using the Searching For Your
Codeprocedure, you may need to find out which four-digit code is

operating your equipment.For example,to find out which code is
operating your TV:

1. On the remote control,press TV once.

2. Press and hold SET until the LED(red light) blinks twice, then
release SET.

3. Enter 9- 9 - 0.The LED will blink twice.

4. To view the code for the first digit,press 1 once.Wait 3 seconds,
count the LEDblinks (e.g., three blinks =3) and write down
the number.

NOTE:If a code digit is “0”,the

LED

will not blink.

5. Repeat step 4 three more times for remaining digits.Use 2 for the
second digit,3 for the third digit,and 4for the fourth digit.

6. To check for codes ofother devices, repeat steps 1 through 5,
but substitute the appropriate device key for each device you
are checking.

USING THE HOME THEATER MODE

The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learningincludes a custom Home Theatermode.
After the HOMETHEATER key is programmed,it will allow you to
access five groups ofremote control keys without having to change
device modes.

Control Organization

About Control Groups

For Home Theater programming,the remote control’s keys are
grouped by type ofcontrol into the following five control groups:

(1) Transport Controls: PLAY,STOP, FWD,REW,PAUSE,and REC
(2) Volume Controls: VOL+,VOL-,and MUTE
(3) Channel Controls: CH+,CH-,(Keypad) 0~ 9, ENTER,LAST,

SLEEP,INFO,and TV/VCR

(4) Menu Controls: MENU,GUIDE,Cursor Controls (Up,Down,

Left,Right), SELECT,and EXIT

(5) PIP Controls: PIP,MOVE,and SWAP

About Device Groups

Moreover,the remote control’s devices are grouped into the following
five device groups:

(1) Device Group 1: VCR,DVD,CD,and RCVR/AMP
(2) Device Group 2: TV,VCR,CBL,SAT, CD,and RCVR/AMP
(3) Device Group 3: TV,VCR,CBL,SAT, CD,and RCVR/AMP
(4) Device Group 4: TV,VCR,CBL,SAT,and DVD
(5) Device Group 5: TV
The default Device Group setting from the factory is:
(1) Device Group 1: VCR
(2) Device Group 2: TV
(3) Device Group 3: CBL
(4) Device Group 4: CBL
(5) Device Group 5: TV

Programming The Home Theater Mode

For example,let’s assume you have a TV,a cable box,and a VCR in
your home theater system.You can set up the Home Theater mode
so that selected controls are assigned to these devices as follows:

1. On the remote control,press HOME THEATER.

2. Press and hold SET until the LED(red light) blinks twice, then
release SET.

3. Enter 9 - 7- 9.The LEDwill blink twice.

4. Select a device. For this example,press VCR once.Then a ssign a
desired Control Groupto t he de v ice.For this example,press PLAY
once,which will assign the entire group ofTran spor t Con trol s
(i.e.,PLAY,STOP, FWD,REW,PAUSE,and REC) to the VCR.The LED
will blink once.

5. Selec t another device.For this example,press TV once. Then
assign a desired Control Group to this device.For this example,
press VOL+once, which will assign the entire group ofVo lum e
Controls(i.e., VOL+,VOL-,and MUTE) to the TV.The LED will
blink once.

6. Selec t another device.For this example,press CBL once. Then
assign a desired Control Group to this device.For this example,
press CH+once, which will assign the entire group ofChannel

Controls(i.e., CH+,CH-, (Keypad) 0~ 9,ENTER, LAST,SLEEP,
INFO,and TV/VCR) to the Cable Box.The LEDwill blink once.

7. To add additional Menu functionality to the Cable Box,press CBL
once. Then press MENUonce . This action will a s sign the entire
group of Menu Controls (i.e.,MENU,GUIDE, Cursor Controls(Up,
Down,Left, Right),SELECT,and EXIT) to the Cable Box.The LED
will blink once.

8. To add PIP functionality to the TV,press TV once.Then press PIP
once.This act ion will assign the entire group of PIP Controls(i.e.,
PIP,MOVE,and SWAP) to the TV.The LEDwill blink once.

9. To exit Home Theater programming,press and hold SET until the

LED(red light) blinks twice, then release SET.

Operating The Home Theater Mode

After programming the Home Theater key (see previous),you simply
activate this mode by pressing HOMETHEATERonce. Instantly,groups
ofremote control keys will be assigned to their programmed devices.

For the above example,pressing HOMETHEATER once would assign
the following keys to the VCR,TV,and Cable Box:

VCR: PLAY,STOP,FWD, REW,PAUSE,and REC
TV: VOL+,VOL-,MUTE, PIP,MOVE,and SWAP
Cable Box: CH+,CH-, (Keypad) 0~ 9,ENTER, LAST,

SLEEP,INFO,TV/VCR, MENU,GUIDE,
Cursor Controls(Up,Down, Left,Right),
SELECT,and EXIT

USING MACROS

With programming,the M1through M4 keys on your One For All 8L
Home Theater Upgradeable Universal Remote Control with Learning
can be setup to perform repetitive,time-consuming operations for
easy,convenient access through the press ofa single key.

Macro keys are ideal for home theater operations,setting a favorite
channel,guide steps,or other multiple functions you would like to
control with one key press.Moreover,each macro key can hold up
to15 key presses total.

NOTE:Programming a new macro over an existing one will erase the
original macro.

Programming A Favorite Channel

With so many channels available through your cable or satellite
system provider,you can program a macro that directly selects a
favorite channel with one key press.

For example,let’s assume your favorite cable programs are on
channel 71.Use the following instructions to program a macro key
for direct access ofthis channel:

NOTE:This example assumes the TV tuner is connected directly to the cable
line and not through a cable box.

1. Press and hold SET until the LED(red light) blinks twice,then
release SET.

2. Enter 9 - 9- 5.The LEDwill blink twice.

3. Select an open macro key (e.g., M1) and press it once.

4. Press TV once.

5. Enter the channel number,7 - 1.

NOTE:If you have access to over 100 channels,enter 0-7-1.Moreover,
ift h e original remote cont rol required pressing an

Enterkey t o change

the channel,also press the

Enter

key after the channel number (e.g.,

0-7-1-Enter

).

6. Press and hold SET until the LEDblinks twice, then release SET.

Now when you press M1,you will instantly see cable channel 71 on
your TV set.

Programming A Master Power Key With Instant Channel
Selection

A macro key can be programmed to turn on and offyour equipment
as well.For example,let’s set up a sequence that will turn on the TV
and tune it to channel3, and then turn on the Cable Box and tune it
to a premium channel (e.g.,11).

NOTE:This example assumes all equipment is turned offand that the TV is
connected through the cable box with TV tuning set to channel 3.

1. Press and hold SET until the LED(red light) blinks twice, then
release SET.

2. Enter 9 - 9- 5.The LEDwill blink twice.

3. Select an open macro key (e.g., M2) and press it once.

4. Enter the following sequence:
TV,POWER,and 0-3(or 0 -0- 3if access is over 100 channels)

NOTE:If the origin al remote control required press ing an Enterkey t o
change the channel,also press the

Enter

key after the channel number (e.g.,

0-7-1-Enter

).

5. Then enter the following sequence:
CBL,POWER,and 1-1(or 0 -1-1 ifaccess is over 100 channels)

6. Press and hold SET until the LEDblinks twice, then release SET.

Now when you press M2once,the TV will turn on and tune to
channel 03.Then the cable box will turn on and tune to channel 11.

Clearing A Macro

1. Press and hold SET until the LED(red light) blinks twice, then
release SET.

2. Enter 9 - 9- 5.The LEDwill blink twice.

3. Select a macro key (e.g., M1~M4) you want to clear and press
it once.

4. Press and hold SET until the LEDblinks twice, then release SET.

USING CHANNEL SCAN

In the TV,VCR, DVD,SAT,and CBLmodes, use the FAVkey to start a
3-second scan ofall favorite channels (if programmed – see
Programming Favorite Channel Scanbelow) and/or all channels for
the selected mode.

1. If Favorite Channel Scan has been set up, skip to step 2.
Otherwise,press TV, VCR,DVD,SAT,or CBL once.

2. Press FAV once.

•IfFavorite Channel Scan has been set up,scanning of favorite

channels will start and,upon completion,continue to scan all
channels upward for the same device.

•IfFavorite Channel Scan has not been set up,scanning will

start with the current channel,then proceed to the next
channel up,and continue until all channels ofthe selected
device is scanned.

3. To stop scanning channels at any time,press any key once
(except the backlight key ).

PROGRAMMING FAVORITE CHANNEL SCAN

In the TV,VCR, DVD,SAT,or CBLmode,you can store a list of up to
10favorite channels,in any order,that wi l l b e immediately scanned
when FAVis pressed (see Using Channel Scan).

NOTE:Only channels ofone mode can be stored for Favorite Channel Scan.

1. On the remote control,press TV, VCR,DVD,SAT,or CBL once.

2. Press and hold SET until the LED(red light) blinks twice,then
release SET.

3. Enter 9 - 9- 6.The LEDwill blink twice.

4. Use the keypad to enter a favorite channel number (e.g.,031).
Then press SETonce.

NOTE:If the origin al remote control required press ing an Enterkey t o
change the channel,also press the

Enter

key after the channel number (e.g.,

0-3-1-Enter

).

5. If desired,repeat step 4 (in this section) for each favorite channel
to be stored,up to a total of10 channels.

NOTE:If you try entering more than 10 channels,the remote control will
automatically exit programming.

6. To exit programming,press and hold SET for 3 seconds.The LED
will blink twice.

USING LEARNING KEYS

Use the learning keys (L1~L4) to add functions that are unique to
your home entertainment devices (e.g.,VCR Tracking Up or Down).

NOTE:Please have your original remote controls handy before programming

learning.Be sure to press each key within 10seconds of the previous entry.If
not,the remote control will exit the programming mode.

Programming A Learning Key

1. Press and hold SET until the LED(red light) blinks twice,then
release SET.

2. Enter 9 - 7- 5.The LEDwill blink twice.

3. Press a device key once (e.g.,TV) to assign a mo de for learning.

4. Press an open learning key once (e.g.,L1) to store a feature to be
learned.The LED will blink rapidly for 4 seconds.If the LED does
not blink rapidly,go back to step 1 and start again.

5. Place your original remote control (e.g.,TV remote control)
head-to-head (about 2" apart) from the One For All 8L Home
Theater Upgradeable Universal Remote Control with Learning.

6. On your original remote control,press and hold the key (i.e.,fea­ture) to be learned until the LEDon the One For All 8L Universal
Remote Control blinks twice.Ifthe LED does not blink twice,
repeat steps 3 through 6.

7. To learn functions onto other learningkeys (e.g., L2 ~ L4),repeat
steps 3 through 6.

8. To lock in new feature(s) on the One For All 8L Universal Remote
Control,press and hold SETuntil the LED blinks twice,then
release SET.

9. To test a learned feature,press a device key (e.g.,TV) once where
the learning mode was assigned.Then press the learning key
(e.g.,L1) where the learned feature is stored.

Deleting Functions From The Learning Keys:

1. Press and hold SET until the LED(red light) blinks twice,then
release SET.

2. Enter 9 - 7- 6.The LEDwill blink twice.

3. Press the device key once where the learned feature is stored
(e.g.,TV).

4. Press the learning key (e.g., L1) to be deleted twice.The LED will
blink twice after the second press.

5. To clear additional functions stored on other learning keys,
repeat steps 1 through 4 (in this section).

RE-ASSIGNING DEVICE KEYS

The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning can be set to control a second TV,VCR,DVD
player,or other device.For example,to control a TV,a cable box,and
twoVCRs,you will need to re-assign the unused AUX key to operate
the second VCR as follows:

1. On the remote control,press and hold SET until the LED(red
light) blinks twice,then release SET.

2. Enter 9 - 9- 2.The LEDwill blink twice.

3. Press VCR once,then press AUX once.

4. The AUX key is now ready to be programmed for your second
VCR. See Programming Device Control.

To re-assign other device keys to the AUXkey,repeat steps 1 through 4
above by substituting the sequence from the below chart:

To Re-Assign Device Key Perform Sequence

AUX as 2nd TV key: SET- 9 - 9- 2 - TV - AUX
AUX as 2nd DVD key: SET- 9 - 9 - 2

-DVD- AUX

AUX as 2nd SAT key: SET- 9 - 9 - 2

-SAT- AUX

AUX as 2nd CD key: SET- 9 - 9 - 2

-CD- AUX

AUX as 2nd CBL key: SET- 9 - 9 - 2

-CBL- AUX

AUX as 2nd RCVR/AMP key: SET- 9 - 9- 2 - RCVR/AMP - AUX

You can also re-sassign another unused device key by substituting an
open key for the AUX key in the above chart and performing the
sequence.For example,to re-assign an unused SAT key as a 2nd CD
key,perfor m SET- 9 - 9 - 2

-CD- SAT

. When a re-assignment is done,
the LED(red light) will blink twice to confirm your choice.At that
time,you will need to program the remote control for the new device
(see Programming Device Control).

USING KEYMOVER

The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning includes a Keymover feature that allows you
to map (or copy) keys from one mode (i.e.,source mode) to another
mode (i.e.,destination mode).

NOTE:The following keys cannot be used as a source or destination:TV,

VCR

,

DVD,AUX,SAT,HOME THEATER,CD,CBL,RCVR/AMP

,and

SET

.

Programming Keymover

For example,if your VCR does not have volume control,you can
map the volume and mute keys from the TVmode to the VCRmode
as follows:

1. Press and hold SET until the LED(red light) blinks twice,then

release SET.

2. Enter 9 - 9- 4.The LEDwill blink twice.

3. For the source mode, press TV once.

4. For the source key,press VOL+ once.

5. For the destination mode, press VCRonce.

6. For the destination key,press VOL + once.

7. The LED will blink twice indicating the keymoved sequence

is correct.

8. Repeat steps 1 through 7 twice more,substituting VOL– and

MUTEas source and destination keys in steps 4 and 6.

Upon completion ofthe above procedure,you can now use your
One For All 8L Home Theater Upgradeable Universal Remote
Control with Learningto control the TV’s volume and mute in the
VCR mode,as well as in the TV mode.

Restoring Keymoved Keys to Default Settings

Restoring A Single Keymoved Key

1. Press a device key that has a keymoved key.

2. Press and hold SET until the LED(red light) blinks twice,then

release SET.

3. Enter 9 - 9- 4.The LEDwill blink twice.

4. Press the destination key twice (where the keymoved key is

stored).The LED will blink twice.

Restoring All Keymoved Keys In A Single Mode

1. Press and hold SET until the LED(red light) blinks twice,then

release SET.

2. Enter 9 - 9- 4.The LEDwill blink twice.

3. Press the destination mode twice (where keymoved keys are
stored).The LED will blink twice.

CHANGING VOLUME LOCK

The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learningis set at the factory for independent volume
control ofeach selected device.However,you may change the Volume
Lock setting to Global Volume Lock so that a device’s volume will be
locked to one mode (e.g.,to control TV volume in all other modes).
After that,ifdesired,you can perform Individual Volume Unlock on a
selected device to set its volume control for independent operation.

Locking Volume Control To One Mode (Global Volume Lock):

1. Press and hold SET until the LED(red light) blinks twice,then
release SET.

2. Enter 9 - 9- 3 and then press any mode key once (e.g.,TV).The
LEDwill blink tw ice.

3. Now,when you press VOL+, VOL–,or MUTE,the volume of the
selected device (e.g.,TV) will be controlled regardless ofthe
mode you have selected.

Unlocking Volume Control For A Single Device (Individual
Volume Unlock):

1. After performing Global Volume Lock (above),press and hold
SETagain until the LED (red light) blinks twice,then release SET.

2. Press a desired mode key where you want volume to be unlocked
(e.g.,RCVR/AMP) and controlled within its own mode.

3. Enter 9 - 9- 3 and then press VOL– once.The LED will blink
four times.

4. If desired,repeat steps 1 through 3 (of t his sec tion) for each
device that you want volume to be unlocked.

5. Now,after you select a device that has volume unlocked (e.g.,
RCVR/AMP),pressing VOL+, VOL–,or MUTE,will control the
device’s volume only in its own m o de.

Unlocking All Volume Control (Restoring Default Setting):

NOTE:Performing these in structions will restore independent volume control
for all programmed devices (e.g.,TV volume control in TVmode,VCR volume
in

VCR

mode,etc.).

1. On the remote control,press and hold SET until the LED(red
light) blinks twice,then release SET.

2. Enter 9 - 9- 3 and then press VOL+ once.The LED will blink
four times.

3. Volume will again be independently controlled according to its
default states for all programmed devices.

ABOUT UPGRADING

The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning has the largest infrared code library available.
However,ifyou purchase a brand new home entertainment or home
automation device,it may not respond to the codes stored in the
remote control’s memory.

Ifthis happens, please contact our Customer Support department
(see Customer Support below) to upgrade the remote control.The
Customer Support representative will search our entire database for
a code that matches your device and instruct you how to enter it into
your One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning.

Ifthe code for your home entertainment or home automation device
is not in our database,we will need to “capture”the code for that
device from its original remote control.A new code would then be
created and entered into your One For All 8L Home Theater
Upgradeable Universal Remote Control with Learning.Ifnecessar y,
the Customer Support representative can instruct you how to begin
the capture procedure.

NOTE:One For All reserves the right to replace a returned remote control with
a new one ofequal or superior functionality.

Upgrade Exclusions

• Home entertainment or home automation devices controlled by
radio frequency (RF/UHF),wired,or ultrasonic remote controls.
Only devices controlled by infraredremote control s are covered.

• Home entertainment or home automation devices not controlled
by remote controls.

• Broken or defective product.

• Products that operate over 100 kHz.

• Infrared keyboards and infrared pointing devices (such as
mouse substitutes).

• All products for sale and/or use outside the continental United
States,Hawaii,Alaska, or Canada.

TROUBLESHOOTING

PROBLEM: If you own a satellite that uses code 0775 (Express Vu

and Echostar) and your exit key does not work,per­form the following sequence to act ivate this
feature/function.

SOLUTION: 1. Press the CBL/SATkey

2. Press and hold the SETkey until the red LED blinks
twice

3. Press 9-9-4,the red LED will blink twice

4. Press SETand release (one blink on LED)

5. Press 3-3-6

6. Press the EXITkey,the red LED will blink twice.

The Exit key will now correctly perform the exit fea-

ture/function on your satellite.
PROBLEM: LED (red light) does not blink when you press a key.
SOLUTION: Replace batteries with four new

AAA

alkaline batteries.

PROBLEM: LED blinks when you press a key,but home entertain-

ment device does not respond.
SOLUTION: Make sure the remote control is aimed at your

home entertainment device and is not farther

than 15feet away.
PROBLEM: The unitdoes not control home entertainment devices

or commands are not working properly.
SOLUTION: Try all listed codes for the device brands being

set up.Make sure they can be operated with an

infrared remote control.
PROBLEM: TV/VCR combo does not respond properly.
SOLUTION: Use the VCR codes for your brand.Some combo

units may require both a TV code and a VCR code

for full operation.
PROBLEM: Changing channels does not work properly.
SOLUTION: Iforiginal remote control required pressing ENTER

to change channels,press ENTER on the remote

control after entering the channel number.
PROBLEM: Dur ing learning,LED emits a long blink after pressing

and holding key to be learned.
SOLUTION: A bad capture has occurred.Avoid high-ambient

light sources,such as direct daylight and fluorescent

bulbs.Try readjusting positions ofremote controls

before performing the procedure again.
PROBLEM: Tried Search For Your Codemethod and still could not

find a working code.
SOLUTION: Clear the device key as follows:Press and hold

SETuntil the LED (red light) blinks twice, then

release.Next enter 9- 9 - 2.Then press the device key

to be cleared twice.Now repeat the Search For Your

Codemethod.
PROBLEM: Remote control does not turn on Sony or Sharp

TV/VCR Combo.
SOLUTION: For power on,these products require programming

TV codes.For Sony, use TV code 0000 and VCR

code 0032.For Sharp,use TV code 0093 and VCR

code 0048.
PROBLEM: CH+ and CH-do not work for your RCA TV.
SOLUTION: Due to RCA design (1983-1987),only the original

remote control will operate these functions.
PROBLEM: No remote control of volume.
SOLUTION: See Changing Volume Lockto lock/unlock volume.

CUSTOMER SUPPORT

For assistance,please contact us in any ofthe following ways:

• E-mail:[e-mail]

• Internet: http://www.oneforall.com

• Consumer Help Line:[phone]

LIMITED WARRANTY

One For All® warrants,to the original purchaser only,that this prod­uct will be free from defects in materials and workmanship,under
normal use,for ninety (90) days from the date oforiginal purchase.

This limited warranty is valid only on ONE FOR ALL® product pur­chased and used in the United States ofAmerica or Canada,and
does not apply to products used for industrial or commercial pur­pose.

The limited warranty does not cover damage or failure caused by
products or services not supplied by ONE FOR ALL® ,or which
result from accident,misuse,abuse,neg lec t, mishandling,misappli­cation,faulty installation,set-up adjustment, improper maintenance,
alteration, maladjustment of consumer controls ,modificati ons,com­mercial use,or that is attributable to acts of God.

There are no express warranties except as listed above.ONE FOR
ALL® SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSE­QUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY.
ALL EXPRESS AND IMPLIED WARRANTIES,INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE,ARE LIMITED TO THE WARRANTY
PERIOD SET FORTH ABOVE.Some states do not allow the exclusion
or limitation ofincidental or consequential damages,or limitations
on how long an implied warranty lasts,so the above exclusions or
limitations may not apply to you.This warranty gives you specific
legal rights and you may also have other rights which vary from
state to state.

To obtain warranty service for a defective product during the war­ranty period,please return the product,preferably in the original
carton,along w ith your purchase receipt,to the store of original pur­chase.A note detailing the complaint would be helpful.The store,at
its option,will replace or repair this product iffound to be defective.

One For All

[phone]

ADDITIONAL INFORMATION

As you update your home entertainment system,One For All® has
a universal remote control that will fit your needs.Look for these
exciting products at a retailer near you.

One For All Access 3..............................................................URC-3605

One For All Video Expert 4 Device.......................................URC-4081

One For All Video Expert Plus 4L.........................................URC-4880

One For All Access 4..............................................................URC-4605

One For All Access 5..............................................................URC-5705

One For All 6 Device Home Theater.....................................URC-6011

One For All 8 Device Home Theater.....................................URC-8011

One For All 8L Device Home Theater

with Learning Capability.......................................................URC-8811

One For All A/V LCD 8 Device With Learning.....................URC-8910

One For All IR/RF LCD 8 Device With Learning..................URC-9910

ONE FOR ALL® is the registered trademark ofUniversal Electronics
Inc.Computime International Ltd.is the Licensee of the ONE FOR
ALL® brand for USA and Canada.

Copyright 2002 by Universal Electronics Inc.No part ofthis publication
may be reproduced,transmitted,transcribed, stored in any retrieval
system,or translated to any language,in any form or by any means,
electronic,mechanical,magnetic, optical,manual,or otherwise, with­out the prior written permission ofUniversal Electronics Inc.

The One For All® 6 Device Universal Remote Control is
compatibile for use in North America,excluding Mexico.

URC-8810w/8811 02/02

▲

▲

▲

▲

8L DEVICE HOME THEATER

UNIVERSAL REMOTE CONTROL

WITH LEARNING

USER’S GUIDE