Omron S8TS-06024-E1, S8TS-06024, S8TS-06024F-E1, S8TS-06024F, S8TS-03012-E1 Product Manual

Switch Mode Power Supply S8TS L-25

Power

Supplies

Switch Mode Power Supply

S8TS

Block-type Switch mode Power Supply That
Mounts to DIN Track

• Power supply range of 60 to 240 W available with just one model
(24-V models).

• Easy creation of multi-power supply configurations with different
output power supplies connected together (24-V, 12-V, and 5-V
models).

• Improve power supply system reliability by creating N+1 redun­dant systems (24-V and 12-V models).

• Approved by UL/CSA standards, EN60950 (IEC 950), and VDE

0160.

Model Number Structure

■ Model Number Legend

Ordering Information

■ Basic Block

■ Bus Line Connector

Note 1. One S8T-BUS01 Connector and one S8T-BUS02 Connector are included as accessories.

2. Bus Line Connectors are ordered separately if necessary.

3. Attached connectors: 2ESDPLM-05P (for output terminal) and 3ESDPLM-03P (for input terminal) made by DINKLE ENTERPRISE.

4. One package contains 10 S8T-BUS01 Connectors.

5. One package contains 10 S8T-BUS02 Connectors.

1 2 3 4

S8TS-@@@@@@-@@

1. Capacity 2. Output Voltage 3. Structure 4. Bus Line Connectors

060: 60 W
030: 30 W
025: 25 W

24: 24 V
12: 12 V
05: 5 V

None: Screw terminals
F: Connector

terminals

None: Basic Block only
E1: S8T-BUS01 and

S8T-BUS02
included

Output voltage Output current Screw terminal type Connector terminal type

(See note 3.)

With Bus Line

Connectors

(See note 1.)

Without Bus Line

Connectors

(See note 2.)

With Bus Line

Connectors

(See note 1.)

Without Bus Line

Connectors

(See note 2.)

24 V 2.5 A S8TS-06024-E1 S8TS-06024 S8TS-06024F-E1 S8TS-06024F
12 V 2.5 A S8TS-03012-E1 S8TS-03012 S8TS-03012F-E1 S8TS-03012F
5 V 5 A --- S8TS-02505 --- S8TS-02505F

Type Number of Connectors Model number

AC line + DC line bus
(For parallel operation)

1 Connector S8T-BUS01

10 Connectors (See note 4.) S8T-BUS11
AC line bus
(For series operation or isolated operation)

1 Connector S8T-BUS02

10 Connectors (See note 5.) S8T-BUS12

L-26 Switch Mode Power Supply S8TS

Specifications

■ Ratings/Characteristics

24/12-V Models (Basic Block: S8TS-06024@/S8TS-03012@)

Note 1. Refer to page 31 for details on adjusting the output voltage for parallel operation. If set to less than −10%, the undervoltage detection func-

tion may operate. Ensure that the output capacity and output current after adjustment do not exceed the rated output capacity and rated
output current respectively.

2. Class 2 approval does not apply to parallel operation.

3. The output current is specified at power output terminals.

4. Refer to the explanations of functions on page 28 for details.

5. Be sure to mount End Plates (PFP-M) on both ends of the Power Supply.

Item Single operation Parallel operation

Efficiency 24-V models: 75% min.; 12-V models: 70% min. (with rated input, 100% load)
Input Voltage 100 to 240 VAC (85 to 264 VAC)

Frequency 50/60 Hz (47 to 63 Hz)
Current 100 V input 24-V models: 1.0 A max.

12-V models: 0.7 A max.

24-V models: 1.0 A × (No. of Blocks) max.
12-V models: 0.7 A × (No. of Blocks) max.

200 V input 24-V models: 0.5 A max.

12-V models: 0.4 A max.

24-V models: 0.5 A × (No. of Blocks) max.
12-V models: 0.4 A × (No. of Blocks) max.

Power factor 24-V models: 0.9 min.; 12-V models: 0.8 min. (with rated input, 100% load) (See note 3.)
Leakage current 100 V input 0.35 mA max. 0.35 mA × (No. of Blocks) max.

240 V input 0.7 mA max. 0.7 mA × (No. of Blocks) max.

Inrush current
(25°C, cold start)
(See note 4.)

100 V input 25 A max. 25 A × (No. of Blocks) max.
200 V input 50 A max. 50 A × (No. of Blocks) max.

Output (See
note 3.)

Voltage adjustment range 24-V models: 22 to 28 V

12-V models: 12 V ±10% (with V.ADJ) (See note 1.)

Ripple 2% (p-p) max.
Input variation influence 0.5% max. (with 85 to 264 VAC input, 100% load)
Load variation influence 2% max. (with rated input, 10% to 100% load) 3% max. (with rated input, 10% to 100% load)
Temperature variation influence 0.05%/°C max. (with rated input and output)
Startup time (See note 4.) 1,000 ms max.
Hold time (See note 4.) 20 ms min. (with 100/200 VAC, rated input)

Additional
functions

Overcurrent protection (See note 4.) 105% to 125% of rated load current, inverted L drop

type, automatic reset

100% to 125% of rated load current inverted L drop

type, automatic reset
Overvoltage protection (See note 4.) Yes
Parallel operation Yes, 4 Blocks max.
N+1 redundant system Yes, 5 Blocks max.
Series operation Yes
Undervoltage indicator (See note 4.) Yes (color: red)
Undervoltage detection output (See

note 4.)

Yes (open collector output), 30 VDC max., 50 mA max.

Other Ambient operating temperature (See

note 4.)

Operating: Refer to the derating curve in Engineering Data.
Storage: −25 to 65°C (with no icing or condensation)

Ambient humidity Operating: 25% to 85%; Storage: 25% to 90%
Dielectric strength 3.0 kVAC, 50/60 Hz for 1 minute (between all inputs and all outputs; detection current: 20 mA)

2.0 kVAC, 50/60 Hz for 1 minute (between all inputs and GR terminal; detection current: 20 mA)

1.0 kVAC for 1 minute (between all outputs and GR terminal; detection current: 20 mA)

Insulation resistance 100 MΩ min. (between all outputs and all inputs, and between all outputs and GR terminal) at 500 VDC
Vibration resistance 10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions
Shock resistance

150 m/s

2

, 3 times each in ±X, ±Y, and ±Z directions

Output indicator Yes (color: green)
Electromagnetic interference Conforms to FCC Class A, EN50081-1
EMI Conforms to EN50081-1/1992
Power factor correction Conforms to EN61000-3-2, EN61000-3-2 A14
EMS Conforms to EN61000-6-2/1999
Approved standards UL: 508 (Listing; Class 2: Per UL1310), 1950, 1604 (Class I, Division 2, Groups A, B, C, D

Hazardous Locations))

cUL: CSA C22.2 No.14, No.213 (Class I, Division 2, Groups A, B, C, D

Hazardous Locations), No. 950 (Class 2) (See note 2.)

EN/VDE: EN50178 (=VDE0160), 60950 (=VDE0806)

Weight 450 g max. 450 g × (No. of Blocks) max.

Switch Mode Power Supply S8TS L-27

Power

Supplies

5-V Models (Basic Block: S8TS-02505@)

Note 1. If set to less than −10%, the undervoltage detection function may operate. Ensure that the output capacity and output current after adjust-

ment do not exceed the rated output capacity and rated output current respectively.

2. The output current is specified at power output terminals.

3. Refer to the explanations of functions on page 28 for details.

4. Be sure to mount End Plates (PFP-M) on both ends of the Power Supply.

■ Reference Value

Item Single operation

Efficiency (typical) 62% min. (with rated input, 100% load)
Input Voltage 100 to 240 VAC (85 to 264 VAC)

Frequency 50/60 Hz (47 to 63 Hz)
Current 100 V input 0.7 A max.

200 V input 0.4 A max.
Power factor 0.8 min. (with rated input, 100% load)
Leakage current 100 V input 0.35 mA max.

240 V input 0.7 mA max.
Inrush current

(25°C, cold start)
(See note 2.)

100 V input 25 A max.

200 V input 50 A max.

Output (See
note 2.)

Voltage adjustment range 5 V ± 10% (with V. ADJ) (See note 1.)
Ripple 2% (p-p) max.
Input variation influence 0.5% max. (with 85 to 264 VAC input, 100% load)
Temperature variation influence 0.05%/°C max. (with rated input and output)
Load variation influence 1.5% max. (with rated input, 10% to 100% load)
Startup time (See note 3.) 1,000 ms max.
Hold time (See note 3.) 20 ms min. (with 100/200 VAC, rated input)

Additional
functions

Overcurrent protection (See note 3.) 105% to 125% of rated load current, inverted L drop type, automatic reset
Overvoltage protection (See note 3.) Yes
Parallel operation No
N+1 redundant system No
Series operation Yes (with the external diode)
Undervoltage indicator (See note 3.) Yes (color: red)
Undervoltage detection output (See note

3.)

Yes (open collector output), 30 VDC max., 50 mA max.

Other Ambient operating temperature (See note

3.)

Operating: Refer to the derating curve in Engineering Data.
Storage: −25 to 65°C (with no icing or condensation)

Ambient humidity Operating: 25% to 85%, Storage: 25% to 90%
Dielectric strength 3.0 kVAC, 50/60 Hz for 1 minute (between all inputs and all outputs; detection current: 20 mA)

2.0 kVAC, 50/60 Hz for 1 minute (between all inputs and GR terminal; detection current: 20 mA)

1.0 kVAC for 1 minute (between all outputs and GR terminal; detection current: 20 mA)

Insulation resistance 100 MΩ min. (between all outputs and all inputs, and between all outputs and GR terminal) at 500 VDC
Vibration resistance 10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions
Shock resistance

150 m/s

2

, 3 times each in ±X, ±Y, and ±Z directions

Output indicator Yes (color: green)
Electromagnetic interference Conforms to FCC Class A, EN50081-1
EMI Conforms to EN50081-1/1992
Power factor correction Conforms to EN61000-3-2, EN61000-3-2A14
EMS Conforms to EN61000-6-2/1999
Approved standards UL: 508 (Listing), 1950, 1604 (Class I, Division 2, Groups A, B, C, D

Hazardous Locations)

cUL: CSA C22.2 No.14, No.213 (Class I, Division 2, Groups A, B, C, D

Hazardous Locations), No. 950

EN/VDE: EN50178 (=VDE0160), 60950 (=VDE0806)

Weight 450 g max.

Item Value Definition

Reliability (MTBF) 250,000 hrs min. MTBF stands for Mean Time Between Failures, which is calculated according to the probability of acci-

dental device failures, and indicates reliability of devices. Therefore, it does not necessarily represent the
life of the product.

Life expectancy 10 yrs min. The life expectancy indicates average operating hours under the ambient temperature of 40°C and a load

rate of 50%. Normally this is determined by the life expectancy of the built-in aluminum electrolytic ca­pacitor.

L-28 Switch Mode Power Supply S8TS

Connections

■ Block Diagrams

S8TS-06024@ and S8TS-03012@

S8TS-02505@

AC (N

)

AC (L

)

INP

UT

DC OUTP

UT

DC LOW

OUT

F

use

2.0

A

Noi

se

filt

er

Rectifi

er

Inrush

curre

nt

p

rotection

circuit

Harmoni

c

curre

nt

suppression

circuit

S

moot

h

ing ci

r

cuit

Drive control
circuit

Ocercurrent
detection circuit

Photocoupler

Current
detection circuit

Detection
circuit

Ocervoltage
detection circuit

Protection

diode

Rectifier an

d

smoothin

g

circuit

Undervoltage
indicator/output

Connected to Bus
Line Connector

Connected to Bus
Line Connector

AC(N)

AC(L) +V

−V

INPUT

DC OUTPUT

DC LOW OUT

Rectifier

Photocoupler

Fuse

2.0 A

Noise
filter

Inrush
current
protection
circuit

Harmonic
current
suppression
circuit

Smooth­ing cir­cuit

Rectifier and
smoothing
circuit

Undervoltage
indicator/output

Drive control
circuit

Detection
circuit

Overvoltage
detection circuit

Overcurrent
detection circuit

Connected to Bus
Line Connector

Connected to Bus
Line Connector

Switch Mode Power Supply S8TS L-29

Power

Supplies

■ Installation

A AC Input Terminal (L): Connect an input line to this terminal.
B AC Input Terminal (N): Connect an input line to this terminal.

C Ground Terminal ( ): Connect a ground line to this terminal.
D Undervoltage Detection Output (DC LOW OUT): Open Collector output

E DC Output Terminal (–V): Connect load lines to this terminal.
F DC Output Terminal (+V): Connect load lines to this terminal.
G Output Indicator (DC ON: Green): Lights while DC output is ON.
H Undervoltage Indicator (DC LOW: Red): Lights when the voltage at the output terminal drops.
I Output Voltage Adjuster (V.ADJ): Use to adjust the voltage.
J Slider: Slide to the lock side when connecting. Unlock the slider when disconnecting.

A AC Input Terminal (L)
B AC Input Terminal (N)

C Ground Terminal ( )
D Parallel Operation Signal Terminal

E DC Output Terminal (+V)
F DC Output Terminal (−V)
G Selector
H Projected Indicator Section

1

7
8
9

4 5 6

2 3

DC ON

DC LOW

DC LOW

V.ADJ

+V

-V

L

LN

N

50/60Hz
AC100

-240V

Class2
Power
Supply

DC24V

2.5A

INPUT

OUTPUT

1.0A

S8TS-06024

POWER SUPPLY

+V-V

10

10

4 5 6

1 2 3

7
8
9

DC ON

DC LOW

DC LOW

V.ADJ

+V

-

V

L

LN

N

50/60Hz

AC100

-240V

Class2
Power
Supply

DC24V

2.5A

INPUT

OUTPUT

1.0A

S8TS-06024F

POWER SUPPLY

+V-V

10

10

Basic Blocks with Screw Terminals: S8TS-@@@@@ Basic Blocks with Connector Terminals: S8TS-@@@@@F

1

8

2

7
3
4
5

6

1

2

3

8

S8T-BUS01 Bus Line Connector
(AC Line + DC Line Bus)

S8T-BUS02 Bus Line Connector
(AC Line Bus)