Omron S82K3-W, S82K7.5-W, S82K15-W, S82K30-W, S82K50-W Product Manual

Switch Mode Power Supply S82K 1

Switch Mode Power Supply

S82K (3/7.5/15/30/50/90/100-W Models)

Ultimate DIN-rail-mounting Power Supply
with a Power Range of 3 to 100 W

• EMI: EN 61204-3 class B

• Input: 85 to 264 VAC (except 90-W and 100-W models)

• Safety standards: UL 60950-1/508, cUL: C22.2, cUR: No.
60950-1/14, Class 2 (UL, CSA), EN 60950-1 (=VDE 0805, Teil 1)

• Undervoltage alarm indication available for standard models.

Note: Refer to “Safety Precautions” on page 13.

Model Number Structure

■ Model Number Legend

Ordering Information

■ List of Models

Note: For details on normal stock models, contact your nearest OMRON representative.

Note:1. The output capacity of the S82K-03005 is 25 W.

2. The output current during parallel operation is 3.78 A.

1. Power Factor Correction

None: No
P: Yes

3. Output Voltage

05: +5 VDC
12: +12 VDC
15: +15 VDC

24: +24 VDC
27: ±12 VDC
28: ±15 VDC

2. Power Ratings

003: 3 W
007: 7.5 W
015: 15 W
030: 30 W

050: 50 W
090: 90 W
100: 100 W

S82K -

1 2 3

Note: Not all combinations are possible. Please refer to the list of models in “Ordering Information” on page 1.

Power ratings Output voltage Output current Function Configuration Models

Output Undervoltage alarm indicator/output PFC

3 W 5 V 0.6 A Single output Yes No S82K-00305

12 V 0.25 A S82K-00312
15 V 0.2 A S82K-00315
24 V 0.13 A S82K-00324

7.5 W 5 V 1.5 A S82K-00705
12 V 0.6 A S82K-00712
15 V 0.5 A S82K-00715
24 V 0.3 A S82K-00724
±12 V 0.3 A/0.2 A Dual output S82K-00727
±15 V 0.2 A/0.2 A S82K-00728

15 W 5 V 2.5 A Single output S82K-01505

12 V 1.2 A S82K-01512
24 V 0.6 A S82K-01524

30 W 5 V 5.0 A S82K-03005 (See note 1.)

12 V 2.5 A S82K-03012
24 V 1.3 A S82K-03024

50 W 24 V 2.1 A S82K-05024
90 W 24 V 3.75 A No S82K-09024

Yes S82K-P09024

100 W 24 V 4.2 A (See note 2.) No S82K-10024

Yes S82K-P10024

2 Switch Mode Power Supply S82K

Specifications

■ Ratings/Characteristics

Note:1. When a load is connected that has a built-in DC-DC converter, the overload protection may operate at startup and the power supply may not start.

Refer to the Overload Protection section on page 8 for details.

2. Use with DC voltage input is beyond the conditions of approval or conformance to applicable safety standards. (DC input possible with 15 W max.
Use the 7.5-W single-output models under the load of 90% max. if the voltage range is between 90 and 110 VDC.
Do not use the Inverter output for the Power supply. Inverters with an output frequency of 50/60 Hz are available, but the rise in the internal temperature of the
Power Supply may result in ignition or burning.

3. Defined with a 100% load and the rated input voltage (100 or 200 VAC.)

4. The output specification is defined at the power supply output terminals.

5. If the V. ADJ adjuster is turned, the voltage will increase by more than +10% of the voltage adjustment range. (+15% for S82K-03012/-03024)

When adjusting the output voltage, confirm the actual output voltage from the Power Supply and be sure that the load is not damaged.

6. The settings for the output voltage must be within the following range:
+V: ±1% of the rated value

−V: ±5% of the rated value

7. Refer to the Overload Protection section on page 8 for details.

8. When using the 7.5-W single-output models within the input voltage range between 90 and 110 VDC, the protection function will operate at a current of 95% to

160% of the rated load current.

Power r atin gs

(See note 1.)

S82K

Single output Dual output Single output

Item 3 W 7.5 W 7.5 W 15 W 30 W

Efficiency (typical) 60% min. (Varies depending

on specifications)

64% min. (Varies depending on specifications) 66% min. (Varies depending on specifications)

Input Voltage

(See note 2.)

AC 100 to 240 VAC (85 to 264 VAC)

DC 90 to 350 VDC Not possible

Frequency 50/60 Hz (47 to 450 Hz)

Current
(See note 3.)

100-V input 0.15 A max. 0.25 A max. 0.45 A max. 0.9 A max.

200-V input 0.25 A max. 0.6 A max.

Power Factor ---

Harmonic current emissions ---

Leakage current
(See note 3.)

100-V input 0.5 mA max.

200-V input 1 mA max.

Inrush current
(See note 3.)

100-V input 15 A max. (for cold start at 25°C)

25 A max. (for cold start at 25°C)

200-V input 30 A max. (for cold start at 25°C)

50 A max. (for cold start at 25°C)

Noise filter Ye s

Out­put
(See
note

4.)

Voltage Adjustment Range ±10% (with V. ADJ) (See note 5.) Not possible (See note 6.) ±10% (with V. ADJ) (−10% to 15% for S82K-03012/-03024)

(See note 5.)

Ripple (See note 3.) 2% (p-p) max.

Input variation influence 0.5% max. (at 85 to 264 VAC input, 100% load)

Load variation influence
(rated input voltage)

1.5% max. (0 to 100% load) +V: 1.5% max.

−V: 3% max. (0 to 100% load)

1.5% max. (0 to 100% load)

Temperature variation influ­ence (See note 3.)

0.05%/°C max.

Start up time 100 ms max. (up to 90% of output voltage at rated input and output)

Hold time (See note 3.) 20 ms min.

Addi­tion­al
func­tions

Overload protection
(See note 7.)

105% to 160% of rated load current (105% to 250% of rated load current for dual output models), gradual current/voltage
drop, automatic reset (See note 8.)

105% to 160% of rated load
current, gradual current in­crease, voltage drop intermit­tent operation, automatic reset

Overvoltage protection No

Undervoltage alarm indica­tion

Yes (color: red)

Undervoltage alarm output No

Parallel operation No

Oth-erOperating ambient tempera-

ture

Refer to the derating curve in Engineering Data. (with no icing or condensation)

Storage temperature −25 to 65°C (with no icing or condensation)

Operating ambient humidity 25°C to 85% (Storage humidity: 25% to 90%)

Dielectric strength 3.0 kVAC for 1 min. (between all inputs and all outputs)

2.0 kVAC for 1 min. (between all inputs and PE terminals)

1.0 kVAC for 1 min. (between all outputs and PE terminals)

Detection
current

10 mA 20 mA

Insulation resistance 100 MΩ min. (between all outputs and all inputs, PE terminals) at 500 VDC

Vibration resistance 10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions

Shock resistance

300 m/s

2

, 3 times each in ±X, ±Y, ±Z directions

Output indicator Yes (color: green)

EMI Conducted

Emissions

Conforms to EN61204-3 EN55011 Class B and based on FCC Class B

Radiated
Emissions

Conforms to EN61204-3 EN55011 Class B

EMS Conforms to EN61204-3 High severity levels

Approved standards UL: UL508 (Listing), 60950-1 Class 2 (excluding Dual output models)

CSA: cUL: C22.2 No.14, cUR: No. 60950-1 Class 2 (excluding Dual output models)
EN/VDE: EN50178 (VDE=0160), EN60950-1 (=VDE0805 Teil 1)
Based on VE0106/P100

Weig ht 150 g max. 260 g max. 380 g max.

Switch Mode Power Supply S82K 3

Note: 1. When a load is connected that has a built-in DC-DC converter, the overload protection may operate at startup and the power supply may not start.

Refer to the Overload Protection section on page 8 for details.

2. Use with DC voltage input is beyond the conditions of approval or conformance to applicable safety standards. (DC input possible with 15 W max.
Use the 7.5-W single-output models under the load of 90% max. if the voltage range is between 90 and 110 VDC.
Do not use the Inverter output for the Power supply. Inverters with an output frequency of 50/60 Hz are available, but the rise in the internal temperature of
the Power Supply may result in ignition or burning.

3. Defined with a 100% load and the rated input voltage (100 or 200 VAC.)

4. The output specification is defined at the power supply output terminals.

5. If the V. ADJ adjuster is turned, the voltage will increase by more than +10% of the voltage adjustment range. (+15% for S82K-03012/-03024)

When adjusting the output voltage, confirm the actual output voltage from the Power Supply and be sure that the load is not damaged.

6. Refer to the Overload Protection section on page 8 for details.

7. When using the 90-W model at an ambient temperature of 25×C or less, the overload protection function will operate at currents from 101% to 111% of the

rated output current. When using the 90-W model at an ambient temperature exceeding 25×C, the overload protection function will operate at currents from
92% to 111% of the rated output current.

8. Parallel operation is set with the Parallel/Single Operation Selector Switch.

9. To meet Class-2 requirements with the 100-W, either a fuse or circuit breaker that is UL listed or CSA certified, and rated at 4.2 A max. should be wired in

series with the load to be connected to the Power Supply. Only then can the Power Supply output be considered as meeting Class 2.

Power ratings

(See note 1.)

S82K S82K-P

Single output

Item 50 W 90 W 100 W 90 W 100 W

Efficiency (typical) 80% min. (Varies depending on specifications)

Input Voltage

(See note 2.)

AC 100 to 240 VAC (85 to 264 VAC) 100 V (85 to 132 VAC)/200 V (170 to 264 VAC) Selectable

DC Not possible

Frequency 50/60 Hz (47 to 450 Hz) 50/60 Hz (47 to 63 Hz)

Current
(See note 3.)

100-V input 1.3 A max. 2.5 A max.

200-V input 0.8 A max. 1.5 A max.

Power Factor --- 0.7 min. (at 200 VAC input, at rated output), 100 V: unlimited

Harmonic current emissions --- Conforms to EN6100-3-2 (200-V only)

Leakage current
(See note 3.)

100-V input 0.5 mA max.

200-V input 1 mA max.

Inrush current
(See note 3.)

100-V input 25 A max. (for cold start at 25°C)

200-V input 50 A max. (for cold start at 25°C)

Noise filter Ye s

Out­put
(See
note

4.)

Voltage Adjustment Range ±10% (with V. ADJ) (−10% to 15% for S82K-05024) (See Note 5.) ±10% (with V. ADJ) (See note 5.)

Ripple (See note 3.) 2% (p-p) max.

Input variation influence 0.5% max. (at 85 to 264 VAC in-

put, 100% load)

0.5% max. (at 85 to 132 VAC input /170 to 264 VAC input, 100% load)

Load variation influence
(rated input voltage)

1.5% max. (0 to 100% load)

Temperature variation influ­ence (See note 3.)

0.05%/°C max.

Start up time 100 ms max. (up to 90% of out-

put voltage at rated input and
output)

200 ms max.

Hold time (See note 3.) 20 ms min.

Addi­tion­al
func­tions

Overload protection
(See note 6.)

105% to 160% of rated load
current, gradual current in­crease, voltage drop intermit­tent operation, automatic reset

105% to 160% of rated load current, inverted L drop, automatic reset (See note 7.)

Overvoltage protection No

Undervoltage alarm indica­tion

Yes (color: red)

Undervoltage alarm output No Yes

Parallel operation No Yes (up to 2 units.) No Yes (up to 2 units.) (See note 8.)

Oth-erOperating ambient tempera-

ture

Refer to the derating curve in Engineering Data. (with no icing or condensation)

Storage temperature −25 to 65°C (with no icing or condensation)

Operating ambient humidity 25°C to 85% (Storage humidity: 25% to 90%)

Dielectric strength 3.0 kVAC for 1 min. (between all inputs and all outputs)

2.0 kVAC for 1 min. (between all inputs and PE terminals)

1.0 kVAC for 1 min. (between all outputs and PE terminals)

Detection
current

20 mA

Insulation resistance 100 MΩ min. (between all outputs and all inputs, PE terminals) at 500 VDC

Vibration resistance 10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions

Shock resistance

300 m/s2, 3 times each in ±X, ±Y, ±Z directions 150 m/s2, 3 times each in ±X, ±Y, ±Z directions

Output indicator Yes (color: green)

EMI Conducted

Emissions

Conforms to EN61204-3
EN55011 Class B and based
on FCC Class B

Conforms to EN61204-3 EN55011 Class B and based on FCC Class A

Radiated
Emissions

Conforms to EN61204-3 EN55011 Class B

EMS Conforms to EN61204-3 High severity levels

Approved standards UL: UL508 (Listing), 60950-1 Class 2 (excluding Dual output models) (See note 9.)

CSA: cUL: C22.2 No.14, cUR: No. 60950-1 Class 2 (excluding Dual output models) (See
note 9.)
EN/VDE: EN50178 (VDE=0160), EN60950-1 (=VDE0805 Teil 1) Based on VE0106/P100

UL: UL508 (Listing), Class 2 (per UL 1310) 60950-1 (See
note 9.)
CSA: cUL: C22.2 No.14, cUR: No. 60950-1 Class 2 (See note

9.)
EN/VDE: EN50178 (VDE=0160), EN60950-1 (=VDE0805
Teil 1) According to VDE0106/P100"

Weig ht 400 g max. 600 g max. 1000g max.

4 Switch Mode Power Supply S82K

Connections

■ Block Diagrams

AC (L)

AC (N)

− V

+ V

Fuse (1 A)

Noise filter

Inrush current
protection
circuit

Rectifier/
smoothing
circuit

Photocoupler

Rectifier/
smoothing
circuit

Detector

Undervoltage
alarm
indicator

Drive control
circuit

Overload
detection
circuit

S82K-003@@ (3 W)
S82K-007@@ (7.5 W, Single Output)

AC (L)

AC (N)

− V

+ V

S82K-007@@ (7.5 W, Dual Outputs)

Fuse (1 A)

Noise filter

Rectifier/
smoothing
circuit

Photocoupler

Rectifier/
smoothing
circuit

Rectifier/smoothing circuit

Detector

Undervoltage
alarm
indicator

3-terminal
REG

Drive control
circuit

Overload
detection
circuit

Inrush current
protection
circuit

AC (L)

AC (N)

− V

+ V

Fuse (3 A)

Noise filter

Rectifier/
smoothing
circuit

Photocoupler

Rectifier/
smoothing
circuit

Detector

S82K-015@@ (15 W)
S82K-030@@ (30 W)
S82K-05024 (50 W)

Inrush current
protection
circuit

Drive control
circuit

Overload
detection
circuit

Undervoltage
alarm
indicator

Switch Mode Power Supply S82K 5

AC (L)

AC (N)

− V

+ V

Fuse (5 A)

Noise filter

Rectifier/
smoothing
circuit

Photocoupler

Rectifier/
smoothing
circuit

Detector

S82K-09024 (90 W)
S82K-10024 (100 W)

100 or 200 V
Selectable
terminals
(See note.)

Inrush current
protection
circuit

Drive control
circuit

Overload
detection
circuit

Note: Use the short bar to short-circuit terminals 7 and 8 to select 100 to 120 VAC and

remove the short bar to select 200 to 240 VAC.

Undervoltage
alarm indicator

AC (L)

AC (N)

− V

+ V

Fuse (5 A)

Noise
filter

Rectifier/
smoothing
circuit

Photocoupler

Rectifier/
smoothing
circuit

Detector

S82K-P09024 (90 W)
S82K-P10024 (100 W)

100 or 200 V
Selectable
terminals
(See note.)

Inrush current
protection
circuit

Harmonic current
emission control
(200-V input only)

Drive control
circuit

Overload
detection
circuit

Note: Use the short bar to short-circuit terminals 7 and 8 to select 100 to 120 VAC and

remove the short bar to select 200 to 240 VAC.

Undervoltage
alarm indicator