Omron NL-200, NL-220, NL-220F User Manual

NL-200, NL-220, NL-220F

LED Lighting Controller

User Manual

84-100022 Rev A

NL-200 Series Controller User Manual

1-1

1 Disclaimer

Except as prohibited by law:

• All hardware, software and documentation is provided on an “as is” basis.

• It is essential that the user ensures that the operation of the product is suitable for their application.

• The user must ensure that incorrect functioning of this equipment cannot cause any dangerous
situation or signicant nancial loss to occur.

• Gardasoft Vision Ltd and Gardasoft Products Ltd will not accept any liability for consequential loss
of any kind.

All trademarks acknowledged. Hardware, software and documentation are Copyright 2002 - 2009 Gardasoft Products Ltd.
Hardware manufactured by Gardasoft Vision Ltd under licence.

Latest Manual Version

For the latest version of this manual, see the Download Center on our web site at:

www.microscan.com.

Technical Support

For technical support, email: [e-mail].

Omron Microscan Systems, Inc.

Renton Headquarters

Tel: [phone]
Fax: [phone]

Nashua Ofce

Tel: [phone]
Fax: [phone]

Omron Microscan Europe

Tel: [phone]
Fax: [phone]

Omron Microscan Asia Pacific

Tel: [phone]
Fax: [phone]

NL-200 Series Controller User Manual

2-1

2 Getting Started

The NL-200 current controller provides repeatable intensity control of LED lighting for machine vision
applications. It includes the intensity control, timing and triggering functions required for machine vi­sion systems.

LED lighting needs a constant current supply as small variations in voltage can cause large variations
in light output. The NL-200 can set currents in steps of 0.1% (with a lower limit of 2.5mA steps to give
very ne control of intensity

.

Before you start consult your NERLITE specification or product labeling for it’s Current Rating. All
specifications can be found on the Omron Microscan website.

NOTE: This current rating is critical to the safe operation of the NERLITE, care must be taken

to determine the correct rating for the light to be connected to the NL-2XX controller.

NOTE: Lighting must not be connected to anything else and must not have a common con­ nection to other lights

NOTE: The NL series has SafePowerTM low heat technology so that in most cases

heatsinking is not required. SafePower also automatically “steps-up” the output volt
age, so that from a 24V supply a higher voltage (eg 36V) can be output.

1.) Read the sections on Safety (Section 3) and Specications (Appendix A) and check the

NL-2XX fulls your requirements.

2.) Mount the NL-2XX as described in Section 4.

3.) Connect the NL-2XX up to a supply as described in Connections (Section 5). When the front

panel is present, the NL-2XX should show two alternating lines on the display to indicate that
it is operating properly.

4.) Read Lighting Setup (Section 7) and then enter the current rating for the lights you need to

connect. Then connect the lights. NOTE: The current release of the NL-2XX does not sup

port Voltage Rating, use only Current Rating to operate your light(s).

5.) Set up the NL-2XX for the desired operation as described in the Conguration sections

(Section 8, 10 or 11).

2-2

NL-200 Series Controller User Manual

Getting Started

2.1 Summary of Features

Throughout this manual, references to the NL-2XX refer to all variants in the NL range unless other­wise stated.

The convention for the part number is:

NL-cd0-vv

NL-cd0F-vv

where:

NL product range name

c Number of channels: 2, 8.

d Conguration option: 0 = front panel, 2 = Ethernet

F Option for fast pulsing

vv Maximum current rating in amps: 2, 20

The following table lists the features on each model.

Feature NL200 NL220 NL220F

Number of channels 2 2 2

Front panel
conguration Yes Yes Yes

Ethernet
conguration No Yes Yes

Fast pulsing No No Yes

NL-200 Series Controller User Manual

3-1

3 Safety

Read this before using the NL-2XX. Always observe the following safety precautions. If in
doubt, contact your distributor or Omron Microscan Systems. The following symbols mean:

Warning: read instructions to understand possible hazard

Warning: Possible hazardous voltage

Warning. Surface may get hot

Where these symbols appear in the manual, refer to the text for precautions to be taken.

3.1 Heat

The NL-2XX can dissipate up to 10W and so can get hot. It should be positioned where personnel

cannot accidentally touch it and away from ammable materials.

Read the Mounting (Section 4). Do not exceed the power ratings given in the manual. Note that at the
maximum ratings the case temperature can reach 65°C.

Ensure that any ventilation holes are not blocked. Allow free ow of air around the unit.

3.2 Electrical

The lighting connections can exceed 46.7V but should not exceed 70V. Pulse peak voltages
above 46.7V are considered hazardous. The lighting connections must be shielded from being
touched along the whole length of the cable and in the light.

The user must ensure that the potential difference between any combination of input signals does not
exceed 46.7V. WARNING: Higher voltages may cause a danger to personal health.

The NL-2XX does not have complete tracking isolation of inputs and outputs.

Transients caused by inductive loads must be suppressed external to the NL2XX.

The NL-2XX outputs high energy pulses. Care must be taken to connect the outputs correctly and
protect the output wiring and load from inadvertent short-circuits. When switched off, there is still
energy stored in the NL-2XX for about 15 seconds.

3.3 General

The NL-2XX must not be used in an application where its failure could cause a danger to personal
health or damage to other equipment.

If the equipment is used in a manner not specied by the manufacturer, the protection provided by the
equipment may be impaired.

NL-200 Series Controller User Manual

4-1

4 Mounting

In order to provide xing points to mount the unit onto a at surface or bracket M3 nuts must be
inserted into one or more of the slots in the base, see illustration below. The quantity and position
of these nuts is dependant upon the users requirements. To t a nut remove one of the end covers.
The nuts can then be slid into the slots and the cover replaced. Ensure that the xing screws used do
not extend past the lower base surface by more than 5.5mm.

See Addendum for installation of optional DIN Rail Mounting Kit.

4.1 Environmental considerations

The NL-2XX enclosure is a re enclosure as long as it is mounted so that none of the connectors are
facing downwards.

If a re enclosure is used, the enclosure should be metal or plastic (with a ammability rating of UL94
V1 or better); with no holes below or to the sides of the NL-2XX when mounted. Cable entries below
the NL-2XX should be via glands that have a ammability rating as before. The NL-2XX should be at
least 10mm from any other part or side of the enclosure.

The NL-2XX does not have an IP rating and should be mounted so that moisture and dirt cannot
enter the unit.

NL-200 Series Controller User Manual

5-1

5 Connections

See the Specication (Appendix A) for information on connection ratings.

5.1 Power Supply

To avoid a re hazard from the NL-2XX or the power supply consider the implica­tions of overheating in the unlikely event of a fault in the NL200. The power dissipa­tion in the NL-2XX in a fault condition can be up to:

<Power supply voltage> * <max current delivered by power supply>

Either limit the power supply output current so that not more than 30W can be dissipated in the
NL200, or mount the unit in a re enclosure.

Choose a PSU that limits its output current by design, by setting the current limit on the supply (if
this feature exists) or use fuses. Remember to derate the fuse, if mounted in an enclosure, as the
temperature will be higher than ambient. The external power supply will need to be able to supply at
least the average output power for all active channels.

The use of a regulated power supply with 100% short circuit protection is recommended. If however a
non-regulated power supply is used, then the maximum ripple voltage of this power supply must not
exceed 10% of the actual DC value.

Route low voltage and mains wiring separately. If they must be loomed together ensure that low volt­age insulation rating is sufcient or that supplementary insulation is used.

Pin Power Input Connector

1 +24V to +48V

2 GND

5.2 Lighting Output

The lighting connections can exceed 46.7V but should not exceed 70V DC.
Pulse peak voltages above 46.7V are considered hazardous. The lighting
connections must be shielded from being touched along the whole length of
the cable and in the light.

Make sure you set the current rating for a light before connecting it. See the Lighting Setup
(Section 7) for details on this.

Light output is on 4-way pluggable screw terminal sockets. It is possible to use two 2-way connectors
in a 4-way socket.

The lighting output connections must not be commoned or grounded in any way.

5-2

NL-200 Series Controller User Manual

Connections

Pin LED12

1 CH1 lighting

out +ve

2 CH1 lighting

out -ve

3 CH2 lighting

out +ve

4 CH2 lighting

out -ve

5.3 Trigger Inputs

There is one trigger input per channel.

The trigger inputs are opto-isolated 3V to 24V input, drawing a minimum of 3mA.

Pin ET12 connector

1 TRIG1 -ve

2 TRIG1 +ve

3 TRIG2 -ve

4 TRIG2 +ve

5.4 12V Power Output

One or two 12V power supply outputs may be present. These can supply up to 1A at 12V for power­ing external cameras and other devices. Do not connect inductive loads or devices that take large
peak currents. Do not exceed the current rating as these outputs are not fused.

Pin PW1 connector PW2 connector

1 GND GND

2 +12V +12V

5.4.1 Ethernet Connection (NL220, NL-220F)

The RJ45 Ethernet connector requires a straight through cable to connect into a network switch, hub
or router. It runs at 10Mbits per second.

NL-200 Series Controller User Manual

5-3

Connections

5.4.2 Connectors

The NL-2XX is supplied with mating connectors for the power supply input, trigger inputs, 12V power
output and lighting output.

Should spare parts be required these can be obtained as follows:

Connector Description Wuerth part Farnell part

number number
www.we-online.com www.farnell.com

Power Wuerth 351 series 691-351­Input 2W screw terminal free skt 500-002 164-1952

Trigger Wuerth 361 series 691-361- 1642-001
Input 4W screw terminal free socket 100-004

12V Wuerth 348 series 691-348- N/A
Output 2W screw terminal free plug 500-002

Lighting Wuerth 348 series 691-348- N/A
Output 4W screw terminal free plug 500-004

NL-200 Series Controller User Manual

6-1

6 General Description

The NL-2XX current controller provides repeatable intensity control of LED lighting for machine vision
applications. It includes the intensity control, timing and triggering functions required for machine vi­sion systems.

LED lighting needs a constant current supply as small variations in voltage can cause large variations
in light output. The NL-2XX can set currents in steps of 0.1% (with a lower limit of 2.5mA steps) to
give very ne control of intensity.

Four modes of operation are provided separately for each channel:

• Continuous (“SCo”):

In continuous mode the output is a continuous brightness.

• Pulse (Strobe) (SPu”):

In pulse mode output is pulsed once per trigger. One trigger input is used as a trigger. The delay
from trigger to pulse, the pulse duration and the brightness can be set.

• Switched (“SOn”):

In switched mode a trigger input can be used to switch the output current on and off. The output
is only enabled when the trigger input has a voltage on it.

• Selected (“SSe”):

In selected mode a trigger input can be used to select between two different intensities..

The NL-2XX is set up using the push buttons and display on the front of the unit. The set up is non­volatile, so the NL-2XX will resume the same operation after a power cycle.

6.1 Output Modes

The trigger inputs are used as follows:

Mode Trigger Input Output

Continuous Unused Output is on.

Switched Trigger = off Output is off

Trigger = on Output is on

Selected Trigger = off Output is continuous brightness 2

Trigger = on Output is continuous brightness 1

Pulsed Trigger rising edge Pulse is triggered if P ag = 1

Trigger falling edge Pulse is triggered if P ag = 0

Note that the P ag inverts the sense of the trigger input.

6.1.1 Continuous Output, Switched Output, Selected Output

In continuous mode the output current Is xed and continuous. Switched mode uses a trigger input to switch
the output on or off. Selected mode uses a trigger input to select between two different brightnesses.

The output current can be varied from 0% to 100% of full brightness.

6.1.2 Pulsed Output

The output is off by default. When the NL-2XX is triggered it will wait for a delay and then pulse the
output. The delay, pulse width, retrigger delay and pulse intensity are all congurable.

Retrigger delay is the minimum allowed time from one trigger to the next. Any triggers that happen too
soon after the previous trigger are ignored. The retrigger delay is set in multiples of 100us.

In pulsed mode, the brightness can be set up to 1000% of its rating, but only for short
periods and at low duty cycles, so that the lighting does not overheat and get damaged.
The duty cycle is limited by ignoring triggers which are too soon after the previous trigger.

Output Brightness Allowed Pulse Width Allowed Duty Cycle

0 to 100% 999ms 100%

101% to 200% 30ms 30%

201% to 300% 10ms 20%

301% to 500% 2ms 10%

501% to 1000% 1ms 5%

So for example, if the brightness is set to 250%, then the NL-2XX will not allow pulses greater than
10ms long. With 10ms pulses, if a trigger occurs within 50ms of a previous trigger (so that the duty
cycle would be greater than 20%) the trigger is ignored.

If necessary the NL-2XX will limit the duty cycle by increasing the retrigger delay.

WARNING: To prevent possible overcurrent condition when operating NERLITE Strobe models, initiate the

brightness setting to 10%, then increase current appropriately.

6.1.3 Fault Detection

The NL-2XX detects the following errors. When the output current is less than 100mA, some fault
detection is turned off.

Error Reason

PO Internal power dissipation is too high. Output turned off.

OP Output current to lighting is too low. The light is open circuit or there is not

enough supply voltage for the requested output current.

SH If the output voltage is too low, the controller detects that the output is short circuited.

HI The voltage required for the lighting has increased too much. Check for ageing of the

lighting or a failed LED.

LO The voltage required for the lighting has decreased too much. Check for ageing of the

lighting or a failed LED.

The user must press SEL to cancel the error and the NL-2XX will then re-sense the light.

6-2

NL-200 Series Controller User Manual

General Description

NL-200 Series Controller User Manual

6-3

General Description

6.2 Cold Start

The NL-2XX conguration can be cleared to the default settings, which clears the lighting ratings and
sets all channels to 50% brightness continuous operation. This can be done from the front panel or by
sending the CL command using Ethernet.

To clear the conguration from the front panel, turn on the NL-2XX while holding the SEL and DOWN
buttons, for about 5 seconds, until ‘COL’ is displayed.. The controller can be cold booted even when
the keypad is locked. The lock is removed by the cold boot.

NL-200 Series Controller User Manual

7-1

7 Lighting Setup

Lighting can be labelled with either a voltage or current rating or both. All NERLITES will have a
current rating, consult specications or product label. This will be used to setup the rating for the light.
This rating is the supply to the lighting that should be used to get 100% continuous brightness from
the light.

WARNING!

When connecting a strobe light to an NL-2XX Series Lighting Controller, you must set the current rat­ing to 10% of the current specied for the light in its conguration guide.

The NL-2XX Series Controller allows the operator to set the brightness (current) to 1000% in strobe
mode. By setting the initial current rating to 10% of the light’s specied current, a brightness setting of
1000% results in the light receiving 100% of its rated current. This will provide maximum light output
without damaging the light.

Note: Certain lights require both channels of the NL-2XX Series Lighting Controller. Channel 1 and
Channel 2 may have different current specications on some models. Be sure each channel is set
correctly as specied in the light’s conguration guide.

The NL-2XX is compatible with both current and voltage rated lighting.

Before connecting a light the rating of the light must be entered. If a light is replaced with a different
type of light, then the rating must be set rst. If a light is replaced with the same type of light then the
previous rating will still apply.

Consult the specication or labelling for the light.

The current rating can be set from 0.01A to 4A in steps of 0.01A.

Voltage and current rated lights are both driven with a constant current. This gives better brightness
stability and allows the NL-2XX to prevent the light being driven with too much power.

7.1 Setting the Rating for a Light

To set the rating of a light on the Ethernet versions of the NL2XX, use the VL command or the internal
webpages.

To set the rating of a light from the front panel, press and hold the SEL button for 1 second. The
display will show “CH1”. Press DOWN to show “rAt” then press SEL. Use UP and DOWN to select
the channel to be set up. Then press SEL and select “Cur” to enter the rated current for each channel.
Then press SEL and set the current. Press SEL to save the rating.

7-2

NL-200 Series Controller User Manual

Lighting Setup

7.2 Light Auto-Sensing

When a channel does not have a light connected, the NL-2XX continually tries to put out a very small
current.

When a light is connected, it will ash for a short time (the light will not be damaged by this) until the
NL-2XX detects that it is connected. For voltage rated lights the light is briey driven at an increasing
current until 100% output is achieved in order to sense the current rating of the light.

Note: Voltage Rating is not a suported feature.

Only use Current “Cur” to enter the rating.

NL-200 Series Controller User Manual

8-1

8 Front Panel

Conguration

(NL-200, NL-220, NL-220F)

8.1 Startup

For controllers with a front panel, On power up, the NL­2XX will display “b r” for 5 seconds, then ‘8.8.8.’ to test the
display is working, then ‘NL2’, then ‘00’, followed by the
rmware version number, eg ‘001’, and then will be ready
for operation. To show that the unit is operating normally, an
alternating pattern is drawn on the display. Once a light is
connected, the controller will sense it, as described below in
Lighting Setup.

Note, if light(s) are connected and have no rating specied
for them, then an error is indicated. To set the rating refer to
section 7.1.

The overall structure of conguration is given to the right.

To congure the controller from the keypad, press and hold
SEL for 1 second. ‘CH1’ will be displayed. Use UP and
DOWN to select which feature to set up.

Pressing and holding MODE at any time will cancel the
operation.

Using the keypad it is possible to set the conguration for
each channel, set a keylock code so that unauthorised
users cannot change any settings, set the internal trigger
timer, view trigger status and set the voltage or current rat­ing of each of the channels.

8.2 Setting the Lighting Rating

This is described in Lighting Setup (Section 7).

8-2

NL-200 Series Controller User Manual

Front Panel Conguration (NL-200, NL-220, NL-220F)

8.3 Default Display

When the NL-2XX is not being congured the display shows the status of all the channels. The seg­ments and their meanings are given below.

Errors are usually caused by a light being connected but the rating for that light has not been set. The
rating of a light can be set as described in Section 7.1.

8.4 Setting Flags

The polarity of the trigger signal (P ag) can be set for some output modes and error checking (E ag)
can be disabled. During conguration the user will be allowed to select between the following:

• F E Error checking enabled

• F - E Error checking disabled

• F P Trigger is active high

• F - P Trigger is active low

NL-200 Series Controller User Manual

8-3

Front Panel Conguration (NL-200, NL-220, NL-220F)

8.5 Setting Up Continuous Output

Continuous output is set up as follows. Select “SCo” for continuous operation.

8-4

NL-200 Series Controller User Manual

Front Panel Conguration (NL-200, NL-220, NL-220F)

8.6 Setting Up Switched Output

Switched output is set up as follows. Select “SOn” for switched operation.

NL-200 Series Controller User Manual

8-5

Front Panel Conguration (NL-200, NL-220, NL-220F)

8.7 Setting Up Selected Output

Select “SSe” mode then enter the two brightness settings.

8-6

NL-200 Series Controller User Manual

Front Panel Conguration (NL-200, NL-220, NL-220F)

8.8 Setting Up Pulsed Operation

Pulsed operation can be set up as follows. If a brightness greater than 100% is selected, the pulse
width will be limited to a safe value as in the table in Section 6.1.2.

WARNING: To prevent possible overcurrent condition when operating NERLITE Strobe models, initiate the

brightness setting to 10% , then increase current appropriately.

NL-200 Series Controller User Manual

8-7

Front Panel Conguration (NL-200, NL-220, NL-220F)

8.9 Setting Pulse Delay and Width Times

When the NL-2XX displays numeric values for the user to change, the right hand digit will be ashing
to indicate that the Up and Down buttons can be used to change the value.

To be able to set pulse delay and pulse width values a scheme is used where the exponent (power of
ten) of the value is set. The exponent values are as follows:

Exp Multiplier Number Range of values
value format

E-2 0.01 9.99 Values are displayed in seconds from 10ms to 5

seconds in steps of 10ms.

E-3 0.001 999. Values are displayed in milliseconds from 1ms to

999ms in steps of 1ms.

E-4 0.0001 99.9 Values are displayed in milliseconds from 0.1ms

to 99.9ms in steps of 0.1ms.

E-5 0.00001 9.99 Values are displayed in milliseconds from

0.01ms to 9.99ms in steps of 0.01ms

E-6 0.000001 999. Values are displayed in microseconds from

1us to 999us in steps of 1us

The ow diagram for entering timings on the keypad is given below.

When a light is pulsed, the display shows that a trigger has occurred by showing ‘PUL’ on the display.

8-8

NL-200 Series Controller User Manual

Front Panel Conguration (NL-200, NL-220, NL-220F)

8.10 Setting the Internal Trigger Timer

An internal timer is available for triggering channels in pulse mode. When this timer is turned on, all
channels in pulse mode will trigger on this timer. The delay and pulse width will be the same as for
external triggers. External triggers will also work.

The period of the timer (the time between triggers) is set as follows.

8.11 Key Lock

The keypad can be locked so that unauthorised users cannot change the conguration. This can be
by setting a lock code. Users who know the lock code can unlock the keypad. The lock code is from
0 to 255, providing moderate protection. The lock code is entered by using the UP/DOWN buttons to
change this number.

NL-200 Series Controller User Manual

8-9

Front Panel Conguration (NL-200, NL-220, NL-220F)

8.12 Viewing Trigger Status

When a channel is in pulse mode, it is possible to view the trigger input status and whether the light
is pulsing. To enter this mode, press and hold SEL for 1 second. Then use UP/DOWN to select “trg”
then press SEL. The display below will be shown. Press SEL to cancel this display.

8.13 View Output Current

An approximate measure of the output current can be viewed from the keypad. The current is up­dated approximately every second, but can be slower for pulse mode.

NL-200 Series Controller User Manual

9-1

9 Ethernet

Communication

(NL-220, NL-220F)

You may need to ask your network administrator for advice about setting up the Ethernet connection.

Ethernet set up is not affected by cold booting the NL220.

9.1 Connection

The Ethernet link uses a 10 base-T connection on an RJ45 connector. The NL-220 Series controller
can be connected to a network switch (or hub or router). It is also possible to connect it direct into the
network port on a PC by using a crossover cable.

9.2 IP Address

The NL-220 Series controller needs an IP address to communicate over Ethernet. There are two
ways to get an IP address; either programmed into the unit or using DHCP.

Most networks use a DHCP server. If there is a PC on the network, You may be able to nd out
whether a PC on the same network uses DCHP as follows:

• Go to Control Panel

• Select Network Connections

• Right click on Local Area Connection. Select Properties

• From the list, select Internet Protocol (TCP/IP), press Properties

If “Obtain an IP address automatically” is set, then DHCP is probably used. However, there may be an
alternative xed IP address on the “Alternative Conguration” tab.

You can nd out what IP address is being used by a PC at any time by:

• Go to Control Panel

• Select Network Connections

• Right click on Local Area Connection. Select Status

• Select the Support tab. The IP address is displayed

When using a xed IP address, you must ensure that you use an IP address that is not being used by
any other device on the network. It is usual to keep the rst three numbers of the IP address the same
as other devices and to change only the last number. For example, if you have a network consisting
of a PC (IP address 192.168.1.35) and two NL200s, you might give them addresses 192.168.1.201
and 192.168.1.202.

9-2

NL-200 Series Controller User Manual

Ethernet Communication (NL-220, NL-220F)

9.2.1 Programmed IP Address and DHCP

For DHCP mode, the NL-220 Series acquires its IP address, subnet mask and gateway address from
a DHCP server. Otherwise the NL-220 Series has a xed IP address, subnet mask and gateway

address.

DHCP mode or the IP address can be set and read via the NL-2XX Series Controller Configuration
Program available for download at www.microscan.com.

9.2.2 Automatic Sensing

All the features below are implemented in the NL Series Lighting Controller Configuration Program
from www.microscan.com.

The NL-220 Series will send out a message on three events:

• On power up

• When an IP address is received or renewed by DHCP

• When an enquiry message is received

On the rst two events, the message is broadcast. On the third it is a reply to a single IP address.

An enquiry message is a UDP packet from source port 30310, destination port 30311 with the
mes-sage body “

Omron Microscan Search” (8-bit ASCII, 13 characters).

The message output by the NL-220 Series is a UDP packet from source port 30311, destination port

30310. It is formatted as:

Omron Microscan, NL220,000000,111111111111,22222222

(8-bit ASCII, 44 characters, where

000000 the serial number of the unit

111111111111 the MAC address in 6 HEX bytes

22222222 the IP address in 4 HEX bytes

For example for NL-220 Series serial number 12345, IP address 192.168.1.103, MAC address

00.0B.75.01.80.99 the packet will contain

Omron Microscan, NL220,012345,000B75018099,C0A80167

NL-200 Series Controller User Manual

10-1

10 Web Page

Configuration (NL-220, NL-220F)

The NL-220 Series has a webserver inside, so that it can be congured from a standard web browser,
such as Internet Explorer.

The IP address of the NL-220 Series must be known (see section 9 on Ethernet Communication.
Open a web browser window and type the IP address (for example 192.168.1.71) of the NL-220 Se­ries into the URL box at the top. The main page of the NL-220 Series webserver should be shown.

10.1 Main Page

The main page shows general information about the NL220. Links are provided to the conguration pages.

10.2 General Setup Page

The General Conguration page allows the webpage protection password to be set or cleared and
the internal trigger to be set up. Also any Ethernet command from Section 11 can be entered.

“Test Mode” referred to on this page is the internal trigger timer.

10.3 Channel Conguration Pages

There is one Channel Conguration Page for each output channel. All the parameters for each output
channel can be set up. Press the Submit button to update the NL-220 Series and save the changes to
non-volatile memory.

The current rating for the light can be changed. Use this with care.

Some measured voltages and the actual output current are displayed on this page.

10-2

NL-200 Series Controller User Manual

Webpage Conguration (NL-220, NL-220F)

NL-200 Series Controller User Manual

11-1

11 Command

Conguration

(NL-220, NL-220F)

The NL-2XX can be congured via the Ethernet connection using UDP or TCP/IP. A Conguration
Program with source code can be downloaded from www.gardasoft.com.

11.1 Ethernet Communication
(NL-220, NL-220F)

For TCP, commands from a host should be sent to destination port 30313. Replies will be to destina­tion port 30312. For UDP, commands from a host should be sent from source port 30312 to destina­tion port 30313. Replies will be sent from source port 30313 to destination port 30312.

A TCP/IP connection will timeout and close if it is idle for more than 10 seconds. The host must send
regular “heartbeat” commands (eg “VR”) to keep the link open.

11.2 Command Structure

Communication consists of commands sent by the host (controlling PC). All output generated by the
command is returned in reply UDP or TCP/IP packets. The last character sent is “>” (“greater than”
symbol). Once this is received, the host knows that the command has been completed.

It is recommended that the host waits for the “>” symbol before sending the next command. UDP
communications are not guaranteed to arrive, so the host software must be able to cope with lost
messages.

Using the GT command, a host can request that a message is sent to it whenever an error occurs.

Several commands can be put into one command line by separating them by a semi-colon (“;”). A car­riage return character should be sent to terminate the command line. The NL-220 will send any replies to
the commands and then send a ‘>’ character to indicate that the command line has been completed.

Commands comprise a code of two letters followed by the parameters (if any) needed for the com­mand. Spaces in the commands are ignored.

Numeric parameters are separated by a comma (“,”). For a parameter which is a time period the
default units are milliseconds. “s”, “ms” or “us” can be added to the end of the number to indicate
seconds, milliseconds or microseconds. For currents, “a” or “ma” can be added to indicate “amps” or
milliamps”. The default is amps.

Note that parameters are in “USA/UK” format so that a half is written “0.5” not “0,5”

11-2

NL-200 Series Controller User Manual

Command Conguration (NL-220, NL-220F)

For example:

Parameter Meaning

0.1 0.1 milliseconds

200us 200 microseconds

0.1s 0.1 seconds

100ma 100mA

2.45A 2.45A

2.3 2300mA or 2.3A

The command codes and their meaning are described below. The upper case commands are shown,
followed by lower case letters denoting the numeric argument.

Error number Reason

Err 1 A parameter value is invalid

Err 2 Command not recognised

Err 3 Numeric value is wrong format

Err 4 Wrong number of parameters

Err 5 (This is only a warning) A timing parameter was

out of range and has been adjusted to a valid value.

Any changes made using Ethernet commands are not saved permanently until the AW command has
been issued.

11.2.1 General Commands

Report the version of rmware running in the NL220F
VR

This command returns the rmware version. For example:
NL-220F Series (HW001) V002

Set the rating of a light

This command sets the current or voltage rating for a light. If a current rating is being set,
then the voltage rating value should be 0.

VLo,v,c

Where:

o = output channel (1 or 2)
v = voltage rating (NOT SUPPORTED Set to 0)
c = current rating (0 or 10mA to 4A)

NL-200 Series Controller User Manual

11-3

Command Conguration (NL-220, NL-220F)

Set continuous mode

The output is set to continuous mode at a percentage of full brightness.
RSc,s
Where:

c = output channel (1 or 2)
s = setting in percent (s = 0 to 100)

Set switched mode

The output is set to switched mode at a percentage of full brightness.
RWc,s
Where:

c = output channel (1 or 2)
s = setting in percent (s = 0 to 100)

Set selected mode

The output is set to selected mode with two brightness settings.
RUc,s,t
Where:

c = output channel (1 or 2)
s = brightness 1 setting in percent (s = 0 to 100)
t = brightness 2 setting in percent (t = 0 to s)

Set pulse mode

The output can be set up to pulse on a trigger input. The delay from trigger to the start of the pulse,
the length of the pulse and the brightness are congurable.

An error is generated if the brightness setting requires a current greater than 20A or if the combination
of pulse width and setting is not allowed.

RTc,p,d,s
RTc,p,d,s,r

Where:

c = output channel (1 or 2)

p = pulse width in milliseconds (0.02 to 999)
d = delay from trigger to pulse in milliseconds (0.02 to 999)
s = setting in percent (s = 0 to 999)
r = retrigger delay. This parameter is optional

Set the Option Flags

REc,m

Where:

c = output channel (1 or 2)
m = ags:
bit 1 = 0 E ag set (error detection enabled)

1 E ag cleared (error detection disabled)

bit 2 = 0 P ag set (positive triggers)

1 P ag cleared (negative triggers)

11-4

NL-200 Series Controller User Manual

Command Conguration (NL-220, NL-220F)

Set the Trigger Input

This command sets which input is used for pulse and switch output modes.

RPc,p

Where:

c = output channel (1 or 2)
p = trigger input (1 or 2)

Set Internal Trigger

Enable or disable the internal trigger. When enabled, all outputs are triggered simultaneously using an
internal trigger signal. This setting can be saved to non-volatile memory using the AW command.

TT0 Disable internal trigger
TT1 Enable internal trigger (uses previously set period)
TT1,p Enable internal trigger and set the period

Where:

p= period of the triggers in microseconds

For example:

TT1,200 Set the internal trigger to 200ms (5Hz)
TT1,500US Set the internal trigger to 500us (2KHz)

Save the settings to memory.

AW

Once the settings are saved to memory they are then retained when the unit is switched
off. If this is not done, changes to the settings are volatile, and if the unit is switched off they
revert to those in force when the last AW command was issued.

Simulate an Input Trigger

TRc

c which input channel (1 or 2)
Simulates a trigger pulse. If the channel is in pulse mode it will pulse and show “PUL” on the
display.

Enable Ethernet Messages

GTm

m = 0 to disable Ethernet messages

= 1 to enable Ethernet messages
When Ethernet messages are enabled, any error reports are sent to the most recent UDP or
TCP address from which a command has been received.
Messages are of the form:

Evtc,e
Where c zero for no channel or channel number (1 or 2)

v event value:

32 to 47 Lighting er or code
128 Light detected and waiting for current rating
129 Light detected and not waiting for current rating

NL-200 Series Controller User Manual

11-5

Command Conguration (NL-220, NL-220F)

Clear any Errors

GR

If Ethernet messages are not enabled, the last event or error number can be read by this
command. Any error displayed on the unit is cleared, so if there was a lighting error, the NL­2XX will resume auto-sensing on that channel.

The reply will be in he same form as the GT command above. If there are no outstanding
events or errors, then only the prompt “>” is returned.

Set/Clear the Webpage Password

EY

EY asc1, asc2, asc3, asc4, asc5, asc6

This command sets the password required to access the webpages. If EY is entered on its
own then the password is cleared. There are six optional parameters, which are decimal ASCII
values for a password from one to six letters. A value of 65 is ‘A’, 66 is ‘B’, etc to 90 is ‘Z’.

Disable Keypad

KBd,c

d = 0 Enable keypad

d = 1 Disable keypad, but allow unlock code

d = 2 Disable keypad, disable unlock code

c Unlock code

In some applications it may be necessary to lock the keypad so that un-authorised operators
cannot change the settings.

A unlock code can be set. This can be used as a low-security way of allowing trusted users
to unlock the keypad. Ethernet commands and the web pages still work. The setting of this
command is restored after a power cycle.

11-6

NL-200 Series Controller User Manual

Command Conguration (NL-220, NL-220F)

11.2.2 Command Summary

Command Example Effect

AW AW Save changes

GT GT1 Enable Ethernet messages

GR GR Clear any error condition.

EY EY65,66 Set webpage password to “AB”

VR VR Read the rmware version

VL VL1,0,0.5 Set the rating of channel 1 to 0.5A

RS RS2,65 Set channel 2 to 65% brightness continuous

RW RW1,50 Set channel 1 to 50%, switch mode

RU RU1,75,25 Set channel 1 to selected mode at 75% and 25%

RT RT2,3,4,50 Set channel 2 to 3ms pulses, delayed by 4ms, at 50% brightness

RP RP1,2 Output channel 1 is triggered using input 2

RE RE1,3 Set channel 1 to ignore lighting errors and not prompt for the

current rating of a light when it is connected

TT TT1,1ms Set internal triggers every 1ms

KB KB1,23 Disable the buttons on the front panel. Set the unlock code to 23.

TR TR2 Trigger channel 2

NOTE: If the above commands are executed using the Web Page feature, they will not be executed
in the command entry area of the Web Page.

NL-200 Series Controller User Manual

A-1

A: Specifications

Output channels Up to 4A continuous or 20A pulsed. Maximum 48V output,

60W average total output power

Lighting Rating 12V to 36V in steps of 1V

100mA to 4A in steps of 10mA

Operating modes Continuous, strobe, switch and selected

Trigger inputs opto-isolated, standard or inverted operation. 3V to 24V

Pulse width 20 microsecond to 1 second. Repeatable to
(NL-200, NL-220) 0.1 microsecond

Pulse width 2 microsecond to 1 second. Repeatable to
(NL-220F) 0.1 microsecond (See Restrictions, Appendix B)

Trigger delay 20 microseconds to 1 second. Repeatable to
(NL-200, NL-220) 2 microseconds

Trigger delay 2 microseconds to 1 second. Repeatable to
(NL-220F) 2 microseconds

Internal trigger timer 0.2Hz to 5KHz

Supply voltage 24VDC to 48VDC regulated

Heat Dissipation 2W per channel typical at maximum output

NL-200 Series Controller User Manual

B-1

B:

Restrictions

The following timings and restrictions apply for rmware revision V002. The restrictions are applied
when settings are saved. Later rmware versions may have lesser limits.

B.1 Continuous Mode

The maximum output current is 4A.

B.2 Switched Mode

The maximum delay from a trigger input changing to the output current being turned on or
off is 10us.

The maximum output current is 0.5A.

B.3 Selected Mode

The maximum delay from a trigger input changing to the output current being turned on or
off is 5ms.

The maximum output current is 0.5A.

B.4 Pulse Mode

The maximum output current is 20A. For high currents pulses the following limits are
recommended. These limits will be improved in future.

Pulses of 2A or more for pulse widths longer than 2ms might cause an error or have a lower current
towards the end of the pulse.

The minimum pulse delay is about 2us. When overdriving or using the retrigger delay, the minimum
delay is around 5us.

For pulse widths less than approximately 70us the output voltage and current cannot be measured.
Because of this, fault detection does not happen and the following restrictions apply:

• For pulse currents greater than 0.5A, the duty cycle will be restricted to no more than 1%

• For pulse currents less than or equal to 0.5A, the duty cycle will be restricted to no more than 10%

Pulse Current Pulse Length Limit

20A 100us
12A 400us
10A 500us
5A 1ms

NL-200 Series Controller User Manual

C-1

C:

Fatal Error Codes

Error number Reason

FAt, Err 44 The NL-200 is too hot. The NL-200 has a thermal cutout which

operates around 65°c to 70°c, depending on conditions.

FAC, Err 40, One channel is outputting more current than expected.
Err 41, Err 45

NL-200 Series Controller User Manual

D-1

D:

Error Codes

Error number Reason

Err 1 A parameter value is invalid

Err 2 Command not recognised

Err 3 Numeric value is wrong format

Err 4 Wrong number of parameters

Err 5 This is a warning, not an error. One of the parameters is out of range.

The value of the parameter has been adjusted. For example, sending
an NL command with a delay of 0 will get a reply of “Err 5”. The command
will be accepted and the delay set to the minimum allowed.

Err 19 A light has been connected to a channel but the rating has not been set.

Err 8, 12 EEPROM corrupt. The conguration has been cleared.

Err 9, 20 Couldn’t save settings to EEPROM.

Err 27 Can’t read Ethernet settings from EEPROM, so these may be incorrect.

PO, Err 34, 39 Internal power dissipation is too high. Output turned off.

OP, Err 35 Output current to lighting is too low.

OP, Err 43 There is not enough supply voltage for the requested output current.

SH, Err 36 The output is short circuit.

SH, Err 42 The output current is too high.

HI, Err 37 The voltage required for the lighting has increased too much.

Check for ageing of the lighting or a failed LED.

SH, Err 38 The voltage required for the lighting has decreased too much.

Check for ageing of the lighting or a failed LED.

Any other errors are internal errors.

NL-200 Series Controller User Manual

E-1

E

: Event Codes

Event messages are sent when a light is connected or an error occurs. The format of these is

Evt<channel>,<event code>;

These event messages are only sent after the GT1 command has been sent.

Event number Reason

1 to 127 An error has occurred. The error code is given by the event number.

128 A light has been connected and is working.

129 A light has been connected but doesn’t have a current or voltage rating.

130 Over temperature error occurred ( FAT)

131 Over current error occurred (FAC)

132 An error has occurred while autosensing the rating of a light.

NL-200 Series Controller User Manual

A

Addendum

Installation – see gure

• Remove either end cover by removing the four screws.

• The clips shown indicate the two orientations available for mounting.

• Select the orientation required, a pair of clips is used for each (AX or AY).

• Slide nuts (B) into the appropriate slots.

• Replace the end cover.

• Screws (C) are passed through mounting clips (A) and into slot nuts (B).

• Position the loose assemblies as required and tighten the screws.

DIN Rail Mounting Kit for NL Range

Pack Contents

Description Drawing Ref Quantity

Mounting Clip A 2

M3 Nut B 2

M3x8mm Countersunk screw C 2