Omron CIMR-V7AZB0P7, CIMR-V7AZB0P1, CIMR-V7AZB1P5, CIMR-V7AZB2P2, CIMR-V7AZB4P0 Brochure & Specs

Advanced Industrial Automation

»

Decentra l i s e d co n t rol

» In te ll ig e n ce on bo ard

»

Ex pan d e d f unc t i ona l i ty

NEW V7 INVERTERS

I m p ro vi n g o n p e r fe c t io n

Since the V7 inverter was launched into the market,

Omron-Yaskawa has installed more than 1.5 million

of V7 series inverters world-wide. It has become

a market reference in reliability. The latter is not

some quantifiable parameter that one can just

mention in the specification sheet. It’s a rather

rigorous process built into the genes

of the product.

Europe’s first choice - V7 inverters
always meet your expectations

The secret of the leader is that it simply runs and runs
until you tell it to stop…

The V7 is designed to operate in the most severe environments.

Hence, it goes far beyond normal expectations (standard

published specifications). For example, it delivers 40% more

current than any inverter on the market. And it does this under

severe conditions, such as high carrier frequency, high

temperature, large voltage fluctuations, etc. The result is that

you get what’s in the box and much more.

Now that’s quality beyond a doubt!

Failure rate for drives

Market standard

Omron-Yaskawa

1 year 5 years

Conventional inverter vs V7 Amps Derating

400V - 4,0 Kw at 40ºC

C.Frq. (KHz)

Output (A)

Omron Yaskawa V7AZ

Conventional inverter

Noisy operation Silent operation

Robu st IG BTs

T h e s e c re t i n s i d e

5%

3%

1%

10,00

8,00

6,00

4,00

2,00

0,00

2,5 3 5 6 7,5 10 12 14

Advanced Industrial Automation

Rotating and static autotune

Besides the standard rotating autotune function, the new

V7 series also features static autotune. This greatly eases drive

setup by eliminating the need to rotate the motor during

autotuning. The result - faster, easier and cheaper installation

and commissioning.

Position control at stop

Embodying advanced on-board processing, V7 inverters offer

unrivalled dynamic control, including fast braking and high-

precision positioning at stop. From full speed to full stop is

achieved faster than market standard inverters. Moreover, this

braking performance is completely independent of the motor

running speed, providing you with perfect control of

your machines.

Packaging feed

Positioning

Product feed

Product out

Speed

S: Travel distance
(blue area)

S

Time

Nominal speed

S>S

Standard stop at
nominal speed.

Stopping without
position control.

Stopping with
position control.

Preferred stop position

Unexpected stop position

New features

• Sensor-less vector controller
ensures 100% at 0.5Hz

• Compact size available
in IP20 or IP65

• Silent operation

• Programming software:
CX-Drive for parameter configuration

• CASE (Inverter application software)

• PLC option board

• High speed Motion Bus: MECHATROLINK-II (ML-II)

• Connectivity: Memobus, Dnet, Profibus, CANopen

• New features:

- Autotuning

- Position control when stopping

- Carrier frequency up to 14KHz

- Analogue positioning

- Improved Up & Down function

- PTC input

- 2 Motors change function

- Free I/O’s setting to be used

from host controller

- Frequency Offsets

- New start / stop sequence

Safe decentralised control

The V7 inverter is also available in a ruggedized IP65 housing,

enabling you to decentralise your drive control without any

extra cabinet costs. Operating independently of the main

control panel, this solution also reduces cabling and saves

on installation time.

MECHATROLINK-II

Using the Omron-Yaskawa MECHATROLINK-II digital motion bus,

you can use the same high-speed motion bus throughout your

machine, from motion controller, servo drives and now also the

inverter. This creates a fully integrated system for the most

advanced motion-control solutions.

PLC functionality

A PLC option board based on Omron’s market-leading PLC

technology offers you all the cost-saving benefits of PLC

functionality. It not only equips the V7 with extra functionality

for a broad range of digital control tasks, it also leads to

significant savings by eliminating the need for a separate PLC.

The board’s inverter-based architecture provides for wireless

installation and seamless access to all V7 parameters. And it

provides external communication via analogue/digital IOs.

Cost-effective customisation with CASE

Special CASE (Customised Application Software) is available

for the V7 series to provide customised control without need

of any extra option boards. CASE gives standard inverters the

performance of a custom-made solution, allowing big savings

in hardware equipment and increasing system reliability.

1Varispeed V7

CIMR-V7AZ

Varispeed V7

Sensorless vector in pocket size

• Nominal torque at 0.5 Hz

• Autotuning

• High carrier up to 14 khz

• Stop accuracy function.

• Integrated PID controller and bidirectional PID-out put

• Motor protection with PTC input

• Pulse input

• Standard digital operator with copy function

• Fieldbus: Modbus, DeviceNet, PROFIBUS, CANopen

• High speed motion bus: ML- II

• Plug-in PLC option unit. Total inverter access.

• CE, UL, and cUL marked

V7 IP65

• Compact size

• Easy wiring

• Built-in filter (Class B)

Customized software*

• The inverter software can be customized to meet
specific application. Examples:

• Traverse sofware S-9381.

*For detailed information please refer to case software section.

Ratings

• 200 V Class single-phase 0.1 to 4 kW

• 200 V Class three-phase 0.1 to 7.5 kW

• 400 V Class three-phase 0.2 to 7.5 kW

System configuration

*See note

*See note

* Option frames are needed for V7 IP65 type.

Communication unit

3G3IV-PCN329-E
Inverter to PC cable

3G3IV-PCN126/326
Digital operator
extension cable

CX-Drive

Braking accessories

PLC option unit

Varispeed
V7

Line filter

3G3IV-PEZZ8122_
DIN attachment

JVOP-144
Remote digital oper.
with potentiometer

JVOP-146
Remote digital oper.
with potentiometer

LKEB_

ERF150WJ_

CDBR_B

* V7 IP65 types are built-in filter inverters.

*See note

Varispeed V7 5

2

Frequency inverters

Type designation

200 V class

400 V class

Specifications

IP20 single-phase: CIMR-V7AZ B0P1 B0P2 B0P4 B0P7 B1P5 B2P2 B4P0

IP65 single-phase: CIMR-V7TZ --- --- B0P405 B0P705 B1P505 B2P205 ---

IP20 three-phase: CIMR-V7AZ 20P1 20P2 20P4 20P7 21P5 22P2 24P0

Maximum permissible motor output kW

1

1. Based on a standard 4-pole motor for maximum applicable motor output. Select the inverter model within the allowable motor rated current

0.12 0.25 0.55 1.1 1.5 2.2 4.0

Output

characteristics

Inverter capacity kVA

0.3 0.6 1.1 1.9 3.0 4.2 6.7

Rated output current A

0.8 1.6 3.0 5.0 8.0 11.0 17.5

Max. output voltage

Proportional to input voltage: 0..240 V

Max. output frequency

400 Hz

Power

supply

Rated input voltage

and frequency

Single-phase 200..240 V 50/60 Hz

3-phase 200..230 V 50/60 Hz

Allowable voltage

fluctuation

-15%..+10%

Allowable frequency

fluctuation

+5%

IP20 three-phase: CIMR-V7AZ

40P2 40P4 40P7 41P5 42P2 43P0 44P0 45P5 47P5

IP65 three-phase: CIMR-V7TZ

40P405 40P705 41P505 42P205 43P005 44P005

Maximum permissible motor output kW

1

1. Based on a standard 4-pole motor for maximum applicable motor output. Select the inverter model within the allowable motor rated current

0.37 0.55 1.1 1.5 2.2 3.0 4.0 5.5 7.5

Output

characteristics

Inverter capacity kVA

0.9 1.4 2.6 3.7 4.2 5.5 7.0 11.0 14.0

Rated output current A

1.2 1.8 3.4 4.8 5.5 7.2 9.2 14.8 18.0

Max. output voltage

Proportional to input voltage: 0..400 V

Max. output frequency

400 Hz

Power

supply

Rated input voltage

and frequency

3-phase 380..460 VAC, 50/60 Hz

Allowable voltage

fluctuation

-15%..+10%

Allowable frequency

fluctuation

+5%

Voltage
B: Single-phase 200 VAC
2: Three-phase 200 VAC
4: Three-phase 400 VAC

Z: European standard specifications

Inverter

V7 series

A: With digital operator (with potentiometer)
T: V7 IP65 type with digital operator
( without potentiometer )

C I M R — V 7 A Z B 0 P 1 0

Max. applicable motor output
0P1: 0.1 kW

7P5: 7.5 kW

~

"P" indicates a decimal
point

[ ]

Protective enclosure:
0: IP20
1: NEMA1
05: IP65

Varispeed V7

3

Commom specifications

Model number

CIMR-V7AZ-@
CIMR-V7TZ-@

Specifications

Control functions

Control methods

Sine wave PWM (V/f control, sensorless vector control)

Output frequency range

0.1..400 Hz

Frequency tolerance

Digital set value: ±0.01% (-10..+50 ºC)
Analogue set value: ±0.5% (25 ±10 ºC)

Resolution of frequency set value

Digital set value: 0.01 Hz (<100 Hz), 0.1 Hz (>100 Hz)

Analogue set value: 1/1000 of maximum frequency

Resolution of output frequency

0.01 Hz

Overload capability

150%/60 s

Frequency set value

0..10 V (20 kΩ), 4..20 mA (250 Ω), 0..20 mA (250 Ω)

Pulse train input, frequency setting value (selectable)

Braking torque
(short term peak torque)

Up to 200 W 150% or more

550 W to 1.1 kW 100% or more

1.5 kW 50% or more

>1.5 kW 20% or more

Continuous braking torque approx. 20% without, 150% with external braking resistor

Functionality

Binary inputs

7 freely programmable inputs

Binary outputs

1 relay output, 2 freely programmable open collector outputs

Analogue output

1 programmable analogue output (0..10 V)/pulse output

Analogue inputs

2 analogue inputs, 0..10 V, 4..20 mA, 0..20 mA

Braking/acceleration times

0.01..6000 s

Display

Optionally frequency, current or set value

Error and status LED

Protection functions

Motor overload protection Electronic thermal overload relay

Instantaneous overcurrent Motor coasts to a stop at approx. 250% of inverter rated current

Overload Motor coasts to a stop after 1 minute at 150% of inverter rated output current

Overvoltage Motor coasts to a stop if DC bus voltage exceed 410 V (double for 400 V class)

Undervoltage

Stops when DC bus voltage is approx. 200 V or less (double for 400 V class)

(approx. 160 V or less for single-phase series)

Momentary power loss

Following items are selectable: not provided (stop if power loss is 15 ms or longer), continuous operation

if power loss is approx. 0.5 s or shorter, continuous operation

Cooling fin overheat Protected by electronic circuit

Stall prevention level Individual levels during accel/constant speed. Decel ON/OFF available. During decel enable/disable selectable.

Cooling fan fault Detected by electronic circuit (fan lock detection)

Ground fault Protected by electronic circuit (operation level is approx. 250% of rated output current)

Power charge indication

RUN lamp stays ON or digital operator LED stays ON until the DC bus voltage becomes 50 V or less.

(Charge LED is provided for 400 V)

Ambient conditions

Degree of protection

IP20, NEMA1, IP65

Cooling

Self cooling for 200 V 0.1..0.4 kW (3 or single phase) and for 400 V 0.2..0.75 kW

Cooling fan for 200 V 0.75 to 7.5 kW and for 400 V 1.5 to 7.5 kW

Ambient temperature

Open air mounting: -10 ºC..50 ºC

Wall mounting: -10 ºC..40 ºC

Ambient humidity

95% (without condensation)

Storage temperature

-20 ºC..+60 ºC (short-term temperature during transportation)

Installation

Indoor (no corrosive gas, dust, etc.)

Installation height

Max. 1000 m

Vibration

10 to 20 Hz, 9.8 m/s2 max; 20 to 50 Hz, 2 m/s2 max

Varispeed V76

Varispeed V7

3

Commom specifications

Model number
CIMR-V7AZ-@

CIMR-V7TZ-@

Specifications

Control functions

Control methods

Sine wave PWM (V/f control, sensorless vector control)

Output frequency range

0.1..400 Hz

Frequency tolerance

Digital set value: ±0.01% (-10..+50 ºC)
Analogue set value: ±0.5% (25 ±10 ºC)

Resolution of frequency set value

Digital set value: 0.01 Hz (<100 Hz), 0.1 Hz (>100 Hz)

Analogue set value: 1/1000 of maximum frequency

Resolution of output frequency

0.01 Hz

Overload capability

150%/60 s

Frequency set value

0..10 V (20 kΩ), 4..20 mA (250 Ω), 0..20 mA (250 Ω)

Pulse train input, frequency setting value (selectable)

Braking torque
(short term peak torque)

Up to 200 W 150% or more

550 W to 1.1 kW 100% or more

1.5 kW 50% or more

>1.5 kW 20% or more

Continuous braking torque approx. 20% without, 150% with external braking resistor

Functionality

Binary inputs

7 freely programmable inputs

Binary outputs

1 relay output, 2 freely programmable open collector outputs

Analogue output

1 programmable analogue output (0..10 V)/pulse output

Analogue inputs

2 analogue inputs, 0..10 V, 4..20 mA, 0..20 mA

Braking/acceleration times

0.01..6000 s

Display

Optionally frequency, current or set value

Error and status LED

Protection functions

Motor overload protection Electronic thermal overload relay

Instantaneous overcurrent Motor coasts to a stop at approx. 250% of inverter rated current

Overload Motor coasts to a stop after 1 minute at 150% of inverter rated output current

Overvoltage Motor coasts to a stop if DC bus voltage exceed 410 V (double for 400 V class)

Undervoltage

Stops when DC bus voltage is approx. 200 V or less (double for 400 V class)

(approx. 160 V or less for single-phase series)

Momentary power loss

Following items are selectable: not provided (stop if power loss is 15 ms or longer), continuous operation

if power loss is approx. 0.5 s or shorter, continuous operation

Cooling fin overheat Protected by electronic circuit

Stall prevention level Individual levels during accel/constant speed. Decel ON/OFF available. During decel enable/disable selectable.

Cooling fan fault Detected by electronic circuit (fan lock detection)

Ground fault Protected by electronic circuit (operation level is approx. 250% of rated output current)

Power charge indication

RUN lamp stays ON or digital operator LED stays ON until the DC bus voltage becomes 50 V or less.

(Charge LED is provided for 400 V)

Ambient conditions

Degree of protection

IP20, NEMA1, IP65

Cooling

Self cooling for 200 V 0.1..0.4 kW (3 or single phase) and for 400 V 0.2..0.75 kW

Cooling fan for 200 V 0.75 to 7.5 kW and for 400 V 1.5 to 7.5 kW

Ambient temperature

Open air mounting: -10 ºC..50 ºC

Wall mounting: -10 ºC..40 ºC

Ambient humidity

95% (without condensation)

Storage temperature

-20 ºC..+60 ºC (short-term temperature during transportation)

Installation

Indoor (no corrosive gas, dust, etc.)

Installation height

Max. 1000 m

Vibration

10 to 20 Hz, 9.8 m/s2 max; 20 to 50 Hz, 2 m/s2 max

Frequency inverters 7

4

Frequency inverters

Digital operator

Indicators
(setting/monitor
item indicators)

Data display

FREQUENCY
adjuster

Operation keys

Appearance Name Function

Data display Displays relevant data items, such as frequency reference, output frequency,

and parameter set values.

Frequency adjuster Sets the frequency reference within a range between 0 Hz and the maximum frequency.

1

Frequency reference indicator The frequency reference can be monitored or set while this indicator is lit.

Output frequency indicator The output frequency of the inverter can be monitored while this indicator is lit.

Output current indicator The output current of the inverter can be monitored while this indicator is lit.

Multi-function monitor indicator The values set in U01 through U10 are monitored while this indicator is lit.

Forward/reverse selection indicator The direction of rotation can be selected while this indicator is lit when operating the inverter

with the RUN key.

Local/remote selection indicator The operation of the inverter through the digital operator or according to the set parameters is

selectable while this indicator is lit.

2

Parameter setting indicator The parameters in n001 through n179 can be set or monitored while this indicator is lit.

3

Mode key Switches the simplified-LED (setting and monitor) item indicators in sequence.

Parameter being set will be canceled if this key is pressed before entering the setting.

Increment key Increases multi-function monitor numbers, parameter numbers, and parameter set values.

Decrement key Decreases multi-function monitor numbers, parameter numbers, and parameter set values.

Enter key Enters multi-function monitor numbers, parameter numbers, and internal data values after they

are set or changed.

RUN key Starts the inverter running when the 3G3MV is in operation with the digital operator

STOP/RESET key Stops the inverter unless parameter n007 is set to disable the STOP key.

Used to reset the inverter when an error occurs.

4

1. V7 IP65 types have digital operator without frequency adjuster.

2. The status of the local/remote selection indicator can be only monitored while the inverter is in operation. Any RUN comand input is ignored while this
indicator is lit.

3. While inverter is in operation, the parameters can be only monitored and only some parameters can be changed. Any RUN command is ignored while the
parameter setting indicator is lit.

4. For safety reasons, the reset function cannot be used while an operation instruction (forward/reverse) is being input. Turn the operation instruction OFF
before using this function.

Varispeed V7

5

Frequenc

IP 20 type 0.1 to 4 Kw

IP20 / NEMA1 type 5.5/7.5 Kw

Dimensions

Voltage class

Max. applicable

motor output kW

Inverter model

CIMR V7AZ

Figure

Dimensions in mm

Weight kg

Cooling
method

W H D W1 H1 H2 D1

Three-phase

200 V

0.12 20P1

1 68

128

76

56

118

5

10

0.6

Self cooled0.25 20P2 0.6

0.55 20P4 108 42 0.9

1.1 20P7 128 62 1.1

Fan cooled

1.5 21P5

2

108

131

96

5

64

1.4

2.2 22P2 140 1.5

4.0 24P0 140 143 128 71 2.1

Single-phase

200 V

0.12 B0P1

1 68

128

76

56 118 5

10

0.6

Self cooled0.25 B0P2 76 0.7

0.55 B0P4 131 42 1.0

1.1 B0P7

2

108

140 96

118 5

64

1.5

Fan cooled

1.5 B1P5 156 96 1.5

2.2 B2P2 140 163 128
71

2.2

4.0 B4P0 170 180 158 2.9

Three-phase

400 V

0.37 40P2

2

108

128

92

96

118 5

16 1.0

Self cooled0.55 40P4 110 34 1.1

1.1 40P7 140

64

1.5

1.5 41P5

156

1.5

Fan cooled

2.2 42P2 1.5

3.0 43P0

140 143 128 71

2.1

4.0 44P0 2.1

Voltage class

Max. applicable

motor output kW

Inverter model

CIMR - V7AZ

Figure

Dimensions in mm (inches)

Weight kg

Cooling
method

W H D W1 H1 H2 D1

Three-phase

200 V

5.5 25P5

3

180 260 170 164 244 8 65

4.6

Fan cooled

7.5 27P5 4.8

Three-phase

400 V

5.5 45P5

180 260 170 164 244 8 65

4.8

7.5 47P5 4.8

W 1

D

D1

8.5

(0.34)

W

H 2 H 1

H

2 M4

W 1

W

H 2 H 1

H

4 M4

D

8.5

(0.34)

D1

Figure 1 Figure 2

Figure 3

Varispeed V78

Varispeed V7

5

Frequenc

IP 20 type 0.1 to 4 Kw

IP20 / NEMA1 type 5.5/7.5 Kw

Dimensions

Voltage class

Max. applicable

motor output kW

Inverter model

CIMR V7AZ

Figure

Dimensions in mm

Weight kg

Cooling
method

W H D W1 H1 H2 D1

Three-phase

200 V

0.12 20P1

1 68

128

76

56

118

5

10

0.6

Self cooled0.25 20P2 0.6

0.55 20P4 108 42 0.9

1.1 20P7 128 62 1.1

Fan cooled

1.5 21P5

2

108

131

96

5

64

1.4

2.2 22P2 140 1.5

4.0 24P0 140 143 128 71 2.1

Single-phase

200 V

0.12 B0P1

1 68

128

76

56 118 5

10

0.6

Self cooled0.25 B0P2 76 0.7

0.55 B0P4 131 42 1.0

1.1 B0P7

2

108

140 96

118 5

64

1.5

Fan cooled

1.5 B1P5 156 96 1.5

2.2 B2P2 140 163 128
71

2.2

4.0 B4P0 170 180 158 2.9

Three-phase

400 V

0.37 40P2

2

108

128

92

96

118 5

16 1.0

Self cooled0.55 40P4 110 34 1.1

1.1 40P7 140

64

1.5

1.5 41P5

156

1.5

Fan cooled

2.2 42P2 1.5

3.0 43P0

140 143 128 71

2.1

4.0 44P0 2.1

Voltage class

Max. applicable

motor output kW

Inverter model

CIMR - V7AZ

Figure

Dimensions in mm (inches)

Weight kg

Cooling
method

W H D W1 H1 H2 D1

Three-phase

200 V

5.5 25P5

3

180 260 170 164 244 8 65

4.6

Fan cooled

7.5 27P5 4.8

Three-phase

400 V

5.5 45P5

180 260 170 164 244 8 65

4.8

7.5 47P5 4.8

W 1

D

D1

8.5

(0.34)

W

H 2 H 1

H

2 M4

W 1

W

H 2 H 1

H

4 M4

D

8.5

(0.34)

D1

Figure 1 Figure 2

Figure 3

Frequency inverters 9

6

Frequency inverters

IIP65 type 0.55 to 4 Kw

Voltage

class

Max.

applicable

motor

output kW

Inverter

model

CIMR V7TZ

Figure

Dimensions in mm

Weight kgCooling

method

W H D W1 W2 H1 H2 H3 D1

Single-phase

200 V

0.55 B0P405

4

280 240 142 260 228 165 38 275 44

3.4 Self cooled

1.1 B0P705 4.3

Fan cooled1.5 B1P505 3.7

2.2 B2P205 4.2

Three-phase

400 V

0.55 40P405

280 240 142 260 228 165 38 275 44

4.2 Self cooled

1.1 40P705 4.3

Fan cooled

1.5 41P505 3.7

2.2 42P205 3.7

3.0 43P005 4.1

4.0 44P005 4.1

W 1

D

D1

W

H 2

H 1

H

Figure 4

W 2

H 1

6 . 4

3x PG25

Varispeed V7

7

IP65 type 0.55 to 4Kw (with option frame accessory attached)

Voltage

class

Max.

applicable

motor

output kW

Inverter

model

CIMR V7TZ

Figure

Dimensions in mm

Weight kgCooling

method

W H D W1 W2 H1 H2 H3 D1 D2

Single-

phase 200 V

0.55 B0P405

5

280 240 180 260 228 165 38 275 44 38

3.6 Self cooled

1.1 B0P705 4.5

Fan cooled1.5 B1P505 3.9

2.2 B2P205 4.4

Three-phase

400 V

0.55 40P405

280 240 180 260 228 165 38 275 44 38

4.4 Self cooled

1.1 40P705 4.5

Fan cooled

1.5 41P505 3.9

2.2 42P205 3.9

3.0 43P005 4.3

4.0 44P005 4.3

Figure 5

W 2

D

D1

H 1

H

D2

W

W 1

6 . 4

H 2

H 1

3x PG25

2x PG12

Varispeed V710

Varispeed V7

7

IP65 type 0.55 to 4Kw (with option frame accessory attached)

Voltage

class

Max.

applicable

motor

output kW

Inverter

model

CIMR V7TZ

Figure

Dimensions in mm

Weight kgCooling

method

W H D W1 W2 H1 H2 H3 D1 D2

Single-

phase 200 V

0.55 B0P405

5

280 240 180 260 228 165 38 275 44 38

3.6 Self cooled

1.1 B0P705 4.5

Fan cooled1.5 B1P505 3.9

2.2 B2P205 4.4

Three-phase

400 V

0.55 40P405

280 240 180 260 228 165 38 275 44 38

4.4 Self cooled

1.1 40P705 4.5

Fan cooled

1.5 41P505 3.9

2.2 42P205 3.9

3.0 43P005 4.3

4.0 44P005 4.3

Figure 5

W 2

D

D1

H 1

H

D2

W

W 1

6 . 4

H 2

H 1

3x PG25

2x PG12

Frequency inverters 11

12

Frequency inverters

Standard connections

Installation

U X

DC reactor (option)

Short bar

Thermal
overload
relay (option)

Braking resistor
(option)

MCCB

R

S

T

Forward run/stop

Reverse run/stop

External fault
(no contact)

Fault reset

JOG command

Multi-step speed
reference 1

Multi­function
input

Multi-step speed
reference 2

Frequency
reference

Pulse train input

Frequency setter

2k

Ω

P

P

MEMOBUS
communication
RS-485/422
max 19.2kBPS

R+

R–

S+

S–

Terminal
resistance

AM

AC

(1/2 W. 120 Ω)

Frequency meter
adjusting potentiometer

Multi-function
analog input 2*

Housing (type : ZHR-3)

Analog monitor
output
0 TO +10 VDC (2 mA)

Pulse monitor
output
(12 VDC
20 mA max. 30

- 70% duty)

Output
frequency

P

FM

Digital operator
frequency setting
potentiometer

min

max

VIN

IIN

GND

+2 +1 – B1 B2

U/T1

V/T2

W/T3

R/L1

S/L2

T/L3

S1

S2

S3

S4

S5

S6

S7

RP

FS

FR

FC

SC

PNP

NPN

Shield connection
terminal

Speed reference
pulse train
(33 kHz max.)

Frequency setting
power supply
(+12 V 20 mA)

Speed frequency
reference
0 to +10 V (20 kΩ) OR
4 to 20 mA (250 Ω)

0 V

P2

P1

MA

MB

MC

PC

Multi-function
photocoupler output
+48 VDC 50 mA or less

Running

Speed
agree

Grounding

Fault

Multi-function
output
250 VAC 1 A or less
30 VDC 1 A or less

IM

: twisted pair shielded wire: shielded wire

P

2*

A housing is required when using the CN2 terminal on the back side of the digital operator.

1m analog input cable (code no. 3G3MV-PCN-CN2) is available for housing on request

A +24 V power supply is required for sequence connection by PNP transistor (+24 V common) .

Shows the following two kinds of connections (factory setting) :

· Input signals (S1 to S7) are non-voltage contacts

· Sequence connection by NPN transistor (0V common)

PHC

PHC

PHC

PHC

PHC

PHC

PHC

24 V

CN2

0 to 10 V

4 to 20 mA

0V

P

Line
filter
1*

1* V7 IP65 types are built-in filter.

Varispeed V7

13

Main circuit

Control Circuit

Terminal Name Function (signal level)

R/L1, S/L2, T/L3

AC power supply input Main circuit power supply input (use R/L1 and S/L2 for single-phase power supply inverter.

Do not use T/L3 of the models less than 0.75 kW for other usage, such as a junction terminal.)

U/T1, V/T2, W/T3

Inverter output For inverter output

B1, B2

Braking resistor connection For braking resistor connection

+2, +1

DC reactor connection Remove the short bar between +2 and +1 when connecting DC reactor (option)

+1, –

DC power supply input For power supply input (+1: positive electrode; – : negative electrode)*

Grounding For grounding (grounding should conform to the local grounding code.)

Type No.

Signal name Function Signal level

Digital input signals

S1

Multi-function input selection 1 Factory setting: runs when CLOSED, stops when OPEN.

24VDC, 8mA
photocoupler
insulation

S2

Multi-function input selection 2 Factory setting: runs when CLOSED, stops when OPEN.

S3

Multi-function input selection 3 Factory setting: "fault reset"

S4

Multi-function input selection 4 Factory setting: "external fault (NO contact)"

S5

Multi-function input selection 5 Factory setting: "multi-step speed reference 1"

S6

Multi-function input selection 6 Factory setting: "multi-step speed reference 2"

S7

Multi-function input selection 7 Factory setting: "JOG command"

SC

Multi-function input selection
Common

Common for control signal

Analog input signals

RP

Speed reference pulse train input 33 kHz max.

FS

Power supply terminal for
frequency setting

+12V (allowable current: 20 mA max.)

FR

Speed frequency reference 0 to +10 VDC (20 kΩ) or 4 to 20 mA (250 Ω), 0 to 20 mA (250 Ω) (resolution 1/1000)

FC

Frequency reference common 0 V

1 (CN2)

Multi-function analog voltage input

Voltage input (between terminals 1 and 3): 0 to 10 VDC (input impedance: 20 kΩ)

Current input (between terminals 2 and 3): 4 to 20 mA (input impedance: 250 Ω)

2 (CN2)

Multi-function analog current input

3 (CN2

Multi-function analog input common

Digital output signals

MA

NO contact output

Factory setting: "fault"

Contact capacity
250 VAC,
1 A or less
30 VDC, 1 A
or less

NC

Contact output

MC

Contact output common

P1

Photocoupler output 1 Factory setting: "running"

Photocoupler output:
+48 VDC, 50 mA or
less

P2

Photocoupler output 2 Factory setting: "at frequency"

PC

Photocoupler output common 0 V

Analog

output

signals

AM

Analog monitor output

Factory setting: "output frequency" 0 to +10 V output

(pulse monitor output available by setting constants. Duty: 30 to 70%)

0 to 10 V 2 mA
or less
Resolution: 8 bits

AC

Analog monitor common 0 V

RS-485/422

R+

Communication input (+)

For MEMOBUS communication
operation by RS-485 or RS-422 communication is available.

RS-485/422
MEMOBUS
protocol

19.2 kBPS max.

R–

Communication input (–)

S+

Communication output (+)

S–

Communication output (–)

Varispeed V712

Varispeed V7

13

Main circuit

Control Circuit

Terminal Name Function (signal level)

R/L1, S/L2, T/L3

AC power supply input Main circuit power supply input (use R/L1 and S/L2 for single-phase power supply inverter.

Do not use T/L3 of the models less than 0.75 kW for other usage, such as a junction terminal.)

U/T1, V/T2, W/T3

Inverter output For inverter output

B1, B2

Braking resistor connection For braking resistor connection

+2, +1

DC reactor connection Remove the short bar between +2 and +1 when connecting DC reactor (option)

+1, –

DC power supply input For power supply input (+1: positive electrode; – : negative electrode)*

Grounding For grounding (grounding should conform to the local grounding code.)

Type No.

Signal name Function Signal level

Digital input signals

S1

Multi-function input selection 1 Factory setting: runs when CLOSED, stops when OPEN.

24VDC, 8mA
photocoupler
insulation

S2

Multi-function input selection 2 Factory setting: runs when CLOSED, stops when OPEN.

S3

Multi-function input selection 3 Factory setting: "fault reset"

S4

Multi-function input selection 4 Factory setting: "external fault (NO contact)"

S5

Multi-function input selection 5 Factory setting: "multi-step speed reference 1"

S6

Multi-function input selection 6 Factory setting: "multi-step speed reference 2"

S7

Multi-function input selection 7 Factory setting: "JOG command"

SC

Multi-function input selection
Common

Common for control signal

Analog input signals

RP

Speed reference pulse train input 33 kHz max.

FS

Power supply terminal for
frequency setting

+12V (allowable current: 20 mA max.)

FR

Speed frequency reference 0 to +10 VDC (20 kΩ) or 4 to 20 mA (250 Ω), 0 to 20 mA (250 Ω) (resolution 1/1000)

FC

Frequency reference common 0 V

1 (CN2)

Multi-function analog voltage input

Voltage input (between terminals 1 and 3): 0 to 10 VDC (input impedance: 20 kΩ)

Current input (between terminals 2 and 3): 4 to 20 mA (input impedance: 250 Ω)

2 (CN2)

Multi-function analog current input

3 (CN2

Multi-function analog input common

Digital output signals

MA

NO contact output

Factory setting: "fault"

Contact capacity
250 VAC,
1 A or less
30 VDC, 1 A
or less

NC

Contact output

MC

Contact output common

P1

Photocoupler output 1 Factory setting: "running"

Photocoupler output:
+48 VDC, 50 mA or
less

P2

Photocoupler output 2 Factory setting: "at frequency"

PC

Photocoupler output common 0 V

Analog

output

signals

AM

Analog monitor output

Factory setting: "output frequency" 0 to +10 V output

(pulse monitor output available by setting constants. Duty: 30 to 70%)

0 to 10 V 2 mA
or less
Resolution: 8 bits

AC

Analog monitor common 0 V

RS-485/422

R+

Communication input (+)

For MEMOBUS communication
operation by RS-485 or RS-422 communication is available.

RS-485/422
MEMOBUS
protocol

19.2 kBPS max.

R–

Communication input (–)

S+

Communication output (+)

S–

Communication output (–)

Frequency inverters 13

14

Frequency inverters

Inverter heat loss

Three-phase 200 V class

Single-phase 200 V class

Three-phase 400 V class

Installation conditions for IP65

Model CIMR-V7AZ 20P1 20P2 20P4 20P7 21P5 22P2 24P0 25P5 27P5

Inverter capacity kVA 0.3 0.6 1.1 1.9 3.0 4.2 6.7 9.5 13

Rated current A 0.8 1.6 3 5 8 11 17.5 25 33

Heat

loss W

Fin 3.7 7.7 15.8 28.4 53.7 60.4 96.7 170.4 219.2

Inside unit 9.3 10.3 12.3 16.7 19.1 34.4 52.4 79.4 98.9

Total heat loss 13.0 18.0 28.1 45.1 72.8 94.8 149.1 249.8 318.1

Model CIMR-V7AZ B0P1 B0P2 B0P4 B0P7 B1P5 B2P2 B4P0

Inverter capacity kVA 0.3 0.6 1.1 1.9 3.0 4.2 6.7

Rated current A 0.8 1.6 3 5 8 11 17.5

Heat

loss W

Fin 3.7 7.7 15.8 28.4 53.7 64.5 98.2

Inside unit 10.4 12.3 16.1 23.0 29.1 49.1 78.2

Total heat loss 14.1 20.0 31.9 51.4 82.8 113.6 176.4

Model CIMR-V7AZ 40P2 40P4 40P7 41P5 42P2 44P0 45P5 47P5

Inverter capacity kVA 1.4 2.6 3.7 4.2 5.5 7.0 11 14

Rated current A 1.8 3.4 4.8 5.5 7.2 8.6 14.8 18

Heat

loss W

Fin 15.1 30.3 45.8 50.5 58.2 73.4 168.8 209.6

Inside unit 15.0 24.6 29.9 32.5 37.6 44.5 87.7 99.3

Total heat loss 30.1 54.9 75.7 83.0 95.8 117.9 256.5 308.9

W =

Inverter

Inverter Inverter

50 mm min. (5.5 and 7.5 KW)

30 mm min. (0.1 to 4.0 KW)

100 mm min.

100 mm min.

Side

Air

Air

Install the inverter vertically in order to ensure proper cooling. When installing the inverter,
always provide the following minimum installation space to allow normal heat dissipation.

1. Always provide enough space for the main circuit or control lines including cable gland.

2. If installing inverters next to one another, provide a minimum spacing of 60mm

.

50 mm or more

50 mm or more

120 mm or more

120 mm or more

40 mm or more 40 mm

or more

Side spaces Top and bottom spaces

Air

Air

Varispeed V7

17

Ordering information

Varispeed V7

200 V 400 V

*See note

*See note

* Option frames are needed for V7 IP65 type.

CB

A

E

D D D D D D

Communication unit

3G3IV-PCN329-E
Inverter to PC cable

3G3IV-PCN126/326
Digital operator
extension cable

CX-Drive

Braking accessories

PLC option unit

Varispeed
V7

Line filter

3G3IV-PEZZ8122_
DIN attachment

JVOP-144
Remote digital oper.
with potentiometer

JVOP-146
Remote digital oper.
with potentiometer

LKEB_

ERF150WJ_

CDBR_B

* V7 IP65 types are built-in filter inverters.

*See note

Specifications Model

1x200 V 0.12 Kw 0.8 A CIMR-V7AZB0P10

0.25 Kw 1.6 A CIMR-V7AZB0P20

0.55 Kw 3.0 A CIMR-V7AZB0P40

1.1 Kw 5.0 A CIMR-V7AZB0P70

1.5 Kw 8.0 A CIMR-V7AZB1P50

2.2 Kw 11.0 A CIMR-V7AZB2P20

4.0 Kw 17.5 A CIMR-V7AZB4P00

3x200 V 0.12 Kw 0.8 A CIMR-V7AZ20P10

0.25 Kw 1.6 A CIMR-V7AZ20P20

0.55 Kw 3.0 A CIMR-V7AZ20P40

1.1 Kw 5.0 A CIMR-V7AZ20P70

1.5 Kw 8.0 A CIMR-V7AZ21P50

2.2 Kw 11.0 A CIMR-V7AZ22P20

4.0 Kw 17.5 A CIMR-V7AZ24P00

5.5 Kw 25.0 A CIMR-V7AZ25P51

7.5 Kw 33.0 A CIMR-V7AZ27P51

Specifications Model

3x400 V 0.37 Kw 1.2 A CIMR-V7AZ40P20

0.55 Kw 1.8 A CIMR-V7AZ40P40

1.1 Kw 3.4 A CIMR-V7AZ40P70

1.5 Kw 4.8 A CIMR-V7AZ41P50

2.2 Kw 5.5 A CIMR-V7AZ42P20

3.0 Kw 7.2 A CIMR-V7AZ43P00

4.0 Kw 9.2 A CIMR-V7AZ44P00

5.5 Kw 14.8 A CIMR-V7AZ45P51

7.5 Kw 18.0 A CIMR-V7AZ47P51

Varispeed V714

Varispeed V7

17

Ordering information

Varispeed V7

200 V 400 V

*See note

*See note

* Option frames are needed for V7 IP65 type.

CB

A

E

D D D D D D

Communication unit

3G3IV-PCN329-E
Inverter to PC cable

3G3IV-PCN126/326
Digital operator
extension cable

CX-Drive

Braking accessories

PLC option unit

Varispeed
V7

Line filter

3G3IV-PEZZ8122_
DIN attachment

JVOP-144
Remote digital oper.
with potentiometer

JVOP-146
Remote digital oper.
with potentiometer

LKEB_

ERF150WJ_

CDBR_B

* V7 IP65 types are built-in filter inverters.

*See note

Specifications Model

1x200 V 0.12 Kw 0.8 A CIMR-V7AZB0P10

0.25 Kw 1.6 A CIMR-V7AZB0P20

0.55 Kw 3.0 A CIMR-V7AZB0P40

1.1 Kw 5.0 A CIMR-V7AZB0P70

1.5 Kw 8.0 A CIMR-V7AZB1P50

2.2 Kw 11.0 A CIMR-V7AZB2P20

4.0 Kw 17.5 A CIMR-V7AZB4P00

3x200 V 0.12 Kw 0.8 A CIMR-V7AZ20P10

0.25 Kw 1.6 A CIMR-V7AZ20P20

0.55 Kw 3.0 A CIMR-V7AZ20P40

1.1 Kw 5.0 A CIMR-V7AZ20P70

1.5 Kw 8.0 A CIMR-V7AZ21P50

2.2 Kw 11.0 A CIMR-V7AZ22P20

4.0 Kw 17.5 A CIMR-V7AZ24P00

5.5 Kw 25.0 A CIMR-V7AZ25P51

7.5 Kw 33.0 A CIMR-V7AZ27P51

Specifications Model

3x400 V 0.37 Kw 1.2 A CIMR-V7AZ40P20

0.55 Kw 1.8 A CIMR-V7AZ40P40

1.1 Kw 3.4 A CIMR-V7AZ40P70

1.5 Kw 4.8 A CIMR-V7AZ41P50

2.2 Kw 5.5 A CIMR-V7AZ42P20

3.0 Kw 7.2 A CIMR-V7AZ43P00

4.0 Kw 9.2 A CIMR-V7AZ44P00

5.5 Kw 14.8 A CIMR-V7AZ45P51

7.5 Kw 18.0 A CIMR-V7AZ47P51

Frequency inverters 15

18

Frequency inverters

Varispeed V7 IP65

200 V 400 V

ALine filters *

* V7 IP65 types are built-in filter inverters.

Specifications Model

1x200 V 0.55 Kw 3.0 A CIMR-V7TZB0P405

1.1 Kw 5.0 A CIMR-V7TZB0P705

1.5 Kw 8.0 A CIMR-V7TZB1P505

2.2 Kw 11.0 A CIMR-V7TZB2P205

Specifications Model

3x400 V 0.55 Kw 1.8 A CIMR-V7TZ40P405

1.1 Kw 3.4 A CIMR-V7TZ40P705

1.5 Kw 4.8 A CIMR-V7TZ41P505

2.2 Kw 5.5 A CIMR-V7TZ42P205

3.0 Kw 7.2 A CIMR-V7TZ43P005

4.0 Kw 9.2 A CIMR-V7TZ44P005

Inverter Line filter

Voltage Model CIMR-V7AZ Schaffner Rasmi Rated current (A) Weight (kg)

3-Phase 200 VAC

20P1 / 20P2 / 20P4 / 20P7 3G3MV-PFI2010-SE 3G3MV-PFI2010-E 10 0.8

21P5 / 22P2 3G3MV-PFI2020-SE 3G3MV-PFI2020-E 20 1.0

24P0 3G3MV-PFI2030-SE 3G3MV-PFI2030-E 30 1.1

25P5 / 27P5 - 3G3MV-PFI2050-E 50 2.3

Single-Phase 200 VAC

B0P1 / B0P2 / B0P4 3G3MV-PFI1010-SE 3G3MV-PFI1010-E 10 0.6

B0P7 / B1P5 3G3MV-PFI1020-SE 3G3MV-PFI1020-E 20 1.0

B2P2 3G3MV-PFI1030-SE 3G3MV-PFI1030-E 30 1.1

B4P0 3G3MV-PFI1040-SE 3G3MV-PFI1040-E 40 1.2

3-Phase 400 VAC

40P2 / 40P4 3G3MV-PFI3005-SE 3G3MV-PFI3005-E 5 1.0

40P7 / 41P5 / 42P2 3G3MV-PFI3010-SE 3G3MV-PFI3010-E 10 1.0

40P4 3G3MV-PFI3020-SE 3G3MV-PFI3020-E 15 1.1

45P5 / 47P5 3G3MV-PFI3030-SE 3G3MV-PFI3030-E 30 2.3

Varispeed V7

19

B Communication cards

C PLC option card

D Option frame accessory for V7 IP65

Type Model

1

1. Option frame accessory is needed for V7 IP65 types when communications option units are used.

Description Function

Communication option board

3G3MV-PDRT2

DeviceNet option card

2

2. For V7 IP65 types with DeviceNet communication, SI-N1/V7 should be used.

• Used for running or stopping the inverter, setting or referencing parameters, and monitoring
output frequency, output current, or similar items through DeviceNet communication with the
host controller.

SI-P1/V7

PROFIBUS-DP option card

• Used for running or stopping the inverter, setting or referencing parameters, and monitoring
output frequency, output current, or similar items through PROFIBUS-DP communication
with the host controller.

SI-S1/V7

Can open option card

• Used for running or stopping the inverter, setting or referencing parameters, and monitoring
output frequency, output current, or similar items through CANopen communication with the
host controller.

3G3MV-PCORT21

Can open gateway

• Used for running or stopping the inverter, setting or referencing parameters, and monitoring
output frequency, output current, or similar items through CANopen communication with the
host controller.

SI-T1/V7

MECHATROLINK-II

option card

• Used for running or stopping the inverter, setting or referencing parameters, and monitoring
output frequency, output current, or similar items through MECHATROLINK-II communica-
tion with the host controller.

• High speed motion bus.

• Host controller: TrajeXia, MCH or MP series.

3

3. Please refer to TrajeXia, MCH or MP series section for host controller technical information.

Type Model

1

1. Option frame accessory is needed on V7 IP65 types when PLC option unit is used.

Description Function

PLC option

3G3MV-P10CDT-E

3G3MV-P10CDT3-E

PLC option

• Full PLC featrues, wireless installation and seamless access to the inverter parameters and
analogue/digital inputs and outputs.

• Standard OMRON tools can be used for programming

• Calendar / clock

PLC option with

RS 422/485

• Same features as standard models with RS 422/485 support.

Type Model Description Function

Option frame

V7TZ-FR1

Option frame

• Frame accessory is needed when communication option unit or PLC option unit are used
with Varispeed V7 IP65.

Varispeed V716

Varispeed V7

19

B Communication cards

C PLC option card

D Option frame accessory for V7 IP65

Type Model

1

1. Option frame accessory is needed for V7 IP65 types when communications option units are used.

Description Function

Communication option board

3G3MV-PDRT2

DeviceNet option card

2

2. For V7 IP65 types with DeviceNet communication, SI-N1/V7 should be used.

• Used for running or stopping the inverter, setting or referencing parameters, and monitoring
output frequency, output current, or similar items through DeviceNet communication with the
host controller.

SI-P1/V7

PROFIBUS-DP option card

• Used for running or stopping the inverter, setting or referencing parameters, and monitoring
output frequency, output current, or similar items through PROFIBUS-DP communication
with the host controller.

SI-S1/V7

Can open option card

• Used for running or stopping the inverter, setting or referencing parameters, and monitoring
output frequency, output current, or similar items through CANopen communication with the
host controller.

3G3MV-PCORT21

Can open gateway

• Used for running or stopping the inverter, setting or referencing parameters, and monitoring
output frequency, output current, or similar items through CANopen communication with the
host controller.

SI-T1/V7

MECHATROLINK-II

option card

• Used for running or stopping the inverter, setting or referencing parameters, and monitoring
output frequency, output current, or similar items through MECHATROLINK-II communica­tion with the host controller.

• High speed motion bus.

• Host controller: TrajeXia, MCH or MP series.

3

3. Please refer to TrajeXia, MCH or MP series section for host controller technical information.

Type Model

1

1. Option frame accessory is needed on V7 IP65 types when PLC option unit is used.

Description Function

PLC option

3G3MV-P10CDT-E

3G3MV-P10CDT3-E

PLC option

• Full PLC featrues, wireless installation and seamless access to the inverter parameters and
analogue/digital inputs and outputs.

• Standard OMRON tools can be used for programming

• Calendar / clock

PLC option with

RS 422/485

• Same features as standard models with RS 422/485 support.

Type Model Description Function

Option frame

V7TZ-FR1

Option frame

• Frame accessory is needed when communication option unit or PLC option unit are used
with Varispeed V7 IP65.

Frequency inverters 17

20

Frequency inverters

E Accessories

E Computer software

Types Model Description Functions

Digital operator

JVOP-146

Remote digital operator

without potentiometer

JVOP-144

Remote digital operator

with potentiometer

72606-CVS31060 Blank cover -----

3G3IV-PEZZ0838BA Digital operator case same as JVOP-144 without operator

Accessories

3G3IV-PCN126
3G3IV-PCN326

Digital operator
extension cable

1 meter

3 meters

-----

3G3IV-PCN329-E PC configuration cable

-----

Types Model Description Installation

Software

CX-drive Computer software Configuration and monitoring software tool

CX-One Computer software Configuration and monitoring software tool

DATA

(15.5)

STOP

78 (3.07)

18.2
(0.72)

88 (3.46)

5

(0.2)

80 (3.15)

4-4.4 DIA. MTG HOLES

58 (2.28)

11

(0.43)

70 (2.76)

15.5 (0.61)

23.1
(0.91)

50 (1.97)

10.5
(0.41)

30.4

(1.20)

1.7

(0.07)

12.2

(0.48)

68 (2.68)

56 (2.20)

4-M4 SPOT FACING
DEEP 3.5 (0.14)

4-4.4 dia. MTG holes

4-M4 spot facing
deep 3.5 (0.14)

DSPL

STOP
RESET

DATA

ENTER

78 (3.07)

18.2
(0.72)

88 (3.46)

5

(0.2)

80 (3.15)

4-4.4 DIA. MTG HOLES

58 (2.28)

11

(0.43)

70 (2.76)

15.5 (0.61)

23.1
(0.91)

50 (1.97)

10.5
(0.41)

30.4

(1.20)

68 (2.68)

56 (2.20)

4-M4 SPOT FACING
DEEP 3.5 (0.14)

RUN

DIGITAL
OPERATOR
JVOP-140

MIN MAX

12.2 (0.48)12.2 (0.48)

9.3 (0.37)

9.3 (0.37)

1.7 (0.07)

1.7 (0.07)

4-4.4 dia. MTG holes

4-M4 spot facing
deep 3.5 (0.14)

Varispeed V7

21

F Braking unit, braking resistor unit

Inverter Braking resistor unit

Voltage Max.

applicable

motor

output kW

Inverter model

CIMR-V7AZ

Inverter-mounted type
(3 %ED, 10 sec max)

Separately-installed type
(10 %ED, 10 sec. max.)

Three-

phase

Single-

phase

Model

ERF-

150WJ_

Resis-

tance

Ω

No. of

used

Braking

torque %

Model
LKEB-

#

Resistor spec.

(per one unit)

W Ω

No. of

used

Braking
torque %

Connectable

min. resis-

tance Ω

200 V

(single-/

three-phase)

0.12 20P1 B0P1 401 400 1 220 – – – – 300

0.25 20P2 B0P2 401 400 1 220 – – – – 300

0.55 20P4 B0P4 201 200 1 220 20P7 70 200 1 220 200

1.1 20P7 B0P7 201 200 1 125 20P7 70 200 1 125 120

1.5 21P5 B1P5 101 100 1 125 21P5 260 100 1 125 60

2.2 22P2 B2P2 700 70 1 120 22P2 260 70 1 120 60

4.0 24P0 B4P0 620 62 1 100 23P7 390 40 1 125 32

5.5 25P5 – – – – – 25P5 520 30 1 115 9.6

7.5 27P5 – – – – – 27P5 780 20 1 125 9.6

400 V
(three-
phase)

0.37 40P2 – 751 750 1 230 – – – – 750

0.55 40P4 – 751 750 1 230 40P7 70 750 1 230 750

1.1 40P7 – 751 750 1 130 40P7 70 750 1 130 510

1.5 41P5 – 401 400 1 125 41P5 260 400 1 125 240

2.2 42P2 – 301 300 1 115 42P2 260 250 1 135 200

3.0 43P0 –
401 400 2 105 43P7 390 150 1 135 100

4.0 44P0 –

5.5 45P5 – – – – – 45P5 520 100 1 135 32

7.5 47P5 – – – – – 47P5 780 75 1 130 32

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Cat. No. I20E-EN-02

Varispeed V718

Varispeed V7

21

F Braking unit, braking resistor unit

Inverter Braking resistor unit

Voltage Max.

applicable

motor

output kW

Inverter model

CIMR-V7AZ

Inverter-mounted type
(3 %ED, 10 sec max)

Separately-installed type
(10 %ED, 10 sec. max.)

Three-

phase

Single-

phase

Model

ERF-

150WJ_

Resis-

tance

Ω

No. of

used

Braking

torque %

Model
LKEB-

#

Resistor spec.

(per one unit)

W Ω

No. of

used

Braking
torque %

Connectable

min. resis-

tance Ω

200 V

(single-/

three-phase)

0.12 20P1 B0P1 401 400 1 220 – – – – 300

0.25 20P2 B0P2 401 400 1 220 – – – – 300

0.55 20P4 B0P4 201 200 1 220 20P7 70 200 1 220 200

1.1 20P7 B0P7 201 200 1 125 20P7 70 200 1 125 120

1.5 21P5 B1P5 101 100 1 125 21P5 260 100 1 125 60

2.2 22P2 B2P2 700 70 1 120 22P2 260 70 1 120 60

4.0 24P0 B4P0 620 62 1 100 23P7 390 40 1 125 32

5.5 25P5 – – – – – 25P5 520 30 1 115 9.6

7.5 27P5 – – – – – 27P5 780 20 1 125 9.6

400 V
(three­phase)

0.37 40P2 – 751 750 1 230 – – – – 750

0.55 40P4 – 751 750 1 230 40P7 70 750 1 230 750

1.1 40P7 – 751 750 1 130 40P7 70 750 1 130 510

1.5 41P5 – 401 400 1 125 41P5 260 400 1 125 240

2.2 42P2 – 301 300 1 115 42P2 260 250 1 135 200

3.0 43P0 –
401 400 2 105 43P7 390 150 1 135 100

4.0 44P0 –

5.5 45P5 – – – – – 45P5 520 100 1 135 32

7.5 47P5 – – – – – 47P5 780 75 1 130 32

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Cat. No. I20E-EN-02

Frequency inverters 19

KPP_V7_01_EN

UNITED KINGDOM

Omron Electronics Ltd

Opal Drive, Fox Milne, Milton Keynes, MK15 0DG, UK
Tel: [phone]
Fax: [phone]
www.omron.co.uk

Austria

Tel: [phone]
www.omron.at

Belgium

Tel: [phone]
www.omron.be

Czech Republic

Tel: [phone]
www.omron.cz

Denmark

Tel: [phone]
www.omron.dk

Finland

Tel: [phone]
www.omron.fi

France

Tel: [phone]
www.omron.fr

Germany

Tel: [phone]
www.omron.de

Hungary

Tel: [phone]
www.omron.hu

Italy

Tel: [phone]
www.omron.it

Netherlands

Tel: [phone]
www.omron.nl

Norway

Tel: [phone]
www.omron.no

Poland

Tel: [phone]
www.omron.pl

Portugal

Tel: [phone]
www.omron.pt

Russia

Tel: [phone]
www.omron-industrial.ru

Spain

Tel: [phone]
www.omron.es

Sweden

Tel: [phone]
www.omron.se

Switzerland

Tel: [phone]
www.omron.ch

Turkey

Tel: [phone]
www.omron.com.tr

Middle East & Africa

Tel: [phone]
www.omron-industrial.com

More Omron representatives
www.omron-industrial.com

Control Systems

• Programmable logic controllers • Human-machine interfaces • Remote I/O

Motion & Drives

• Motion controllers • Servo systems • Inverters

Control Components

• Temperature controllers • Power supplies • Timers • Counters • Programmable relays

• Digital panel indicators • Electromechanical relays • Monitoring products • Solid-state relays

• Limit switches • Pushbutton switches • Low voltage switch gear

Sensing & Safety

• Photoelectric sensors • Inductive sensors • Capacitive & pressure sensors • Cable connectors

• Displacement & width-measuring sensors • Vision systems • Safety networks • Safety sensors

• Safety units/relay units • Safety door/guard lock switches

Aut hori sed Dis tri buto r:

Although we strive for perfection, Omron Europe BV and/or its subsidiary and affiliated companies do not warrant
or make any representations regarding the correctness or completeness of the information described in this document.
We reserve the right to make any changes at any time without prior notice.

OMRON EUROPE B.V.

Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. Tel: [phone] Fax: [phone] www.omron-industrial.com