Omnitronic XO-2300 User Manual

10304055_EF.DOC

1/20

BEDIENUNGSANLEITUNG

USER'S MANUAL

MODE D'EMPLOI

XO-2300

Active crossover

©

COPYRIGHT

Nachdruck verboten!
All rights reserved!
Réproduction interdite!

Für weiteren Gebrauch aufbewahren!

Keep this manual for further needs!

Gardez ces instructions pour des utilisations ultérieurs!

10304055_EF.DOC

2/20

10304055_EF.DOC

3/20

OPERATING INSTRUCTIONS

XO-2300

Active crossover

For your own safety, please read this user manual carefully before you initial start-up.

Every person involved with the installation, operation and maintenance of this device has to

- be qualilfied

- follow the instructions of this manual

- consider this manual to be part of the total product

- keep this manual for the entire service life of the product

- pass this manual on to every further owner or user of the product

- include every supplementay update with the original manual

INTRODUCTION

Thank you for having chosen an OMNITRONIC XO-2300. You have acquired a reliable and powerful device.
If you follow the instructions given in this manual, we can assure you that you will enjoy this device for many
years.

Unpack your OMNITRONIC crossover.

Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C
connection cable or on the casing, do not take the device into operation and immediately consult your local
dealer.

Features

High-quality active stereo crossover

2-way stereo or 3-way mono operation possible • 24 dB octave slope • Without frequency-cards, as
adjustment of the crossover frequency is effected via a rotary control on the front panel • Frequency range of
crossover frequency 100 Hz to 10 kHz • Additional Low Sum output • 19"-dimensions

10304055_EF.DOC

4/20

SAFETY INSTRUCTIONS

CAUTION!

Be careful with your operations. With a dangerous voltage you can suffer a dangerous
electric shock when touching the wires!

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will
not accept liability for any resulting defects or problems.

Always plug in the power plug least. Make sure that the power-switch is set to OFF position before you
connect the device to the mains.

Keep away from heaters and other heating sources!

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it
on immediately. The arising condensation water might damage your device. Leave the device switched off
until it has reached room temperature.

Never put any liquids on the device or close to it. Should any liquid enter the device nevertheless, disconnect
from mains immediately. Please let the device be checked by a qualified service technician before you
operate it again. Any damages caused by liquids having entered the device are not subject to warranty!

This device falls under protection-class I. The power plug must only be plugged into a protection class I
outlet.

Never let the power-cord come into contact with other cables! Handle the power-cord and all connections
with the mains with particular caution!

Make sure that the available voltage is not higher than stated on the AC voltage selector.

Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the
power-cord from time to time.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power-cord by the plug. Never pull out the plug by tugging the power-cord.

Before the device is switched on all faders and volume controls have to be set to "0" or "min" position.

CAUTION: Turn the amplifier on last and off first!

Keep away children and amateurs!

CAUTION: High volumes can cause hearing damage!

There are no serviceable parts inside the device. Maintenance and service operations are only to be carried
out by authorized dealers.

OPERATING DETERMINATIONS

This device is a professional crossover. This product is allowed to be operated with an alternating current of
115/230 V, 50/60 Hz and was designed for indoor use only.

Do not shake the device. Avoid brute force when installing or operating the device.