Omega Products CNiTH-i32-AL Installation Manual

Step 17. Enter Alarm 1 Enable/Disable Submenu

Press dto display flashing

DSBL/ ENBL

Step 18. Enable Alarm 1 Submenu

If flashing

ENBL

is displayed, press a, if

DSBL

is displayed,

press buntil

ENBL

is displayed, then press dto store and

go to the next menu item.

Step 19. Select the Deviation Control Type Submenu

Press d. If flashing

_DEV

Deviation is displayed press a,

otherwise press buntil flashing

_DEV

is shown. Now

press dto store and go to next menu item.

Step 20. Select the Latched Type Submenu

Press d. If flashing

UNLT

Unlatched is displayed press a,

otherwise press buntil

UNLT

is displayed.

Press dto store and advance to next menu item.

Step 21. Select the Normally Open Type of Contact Closure Submenu

Press d. If flashing

N.o.

Normally Open is displayed,

press a, otherwise press buntil

N.o.

is displayed. Press

to store and advance to next menu item.

Step 22. Select the Above Type of Active Submenu

Press d. If flashing

ABoV

Above is displayed, press a,

otherwise press b until

ABoV

is displayed. Press d to store

and advance to next menu item.

Step 23. Enable Alarm 1 at Power On

(

A.P.oN

)

Press d. If flashing

ENBL

is displayed, press a, otherwise

press buntil

ENBL

is displayed. Press dto store and

advance to next menu item.

Step 24. Enter Alarm 1 High Submenu

Press atwice to skip

ALR.L

Alarm 1 Low value.

ALR.L

for below &

ALR.H

for above.

Step 25. Set the Alarm 1 High value

(

ALR.H

)

Press d. Press bor cuntil value to set the display to

002.0

. Press dto save.

Step 26. Enter the Alarm 2 Menu

The display will show

ALR2

the top menu for Alarm 2. Repeat steps from 17 to 25 to set for Alarm 2 the same conditions as for Alarm 1.

Step 27. Skip the Loop Break Time Menu

(

LOOP

)

Press ato go to the

OUT1

Output 1 Menu item.

Step 28. Configuration the Output 1 Menu

Set Alarm 1 Disabled (Step 18) to be able to Enable Output 1.

Step 29. Configuration of Display Color Selection

Press auntil the

COLR

Display Color Selection Menu

appears on the Display. Configure

COLR

N.CLR/GRN

(green),

1.CLR/ RED

(red),

2.CLR/AMBR

(amber). Please

refer to the operator’s manual if needed.

For color change on Setpoints refer to Owners Manual Section 2.

OPERATION Step 1. Apply Power to the Instrument

When your device is first powered up it will display the ambient temperature (assume 75°F).

Step 2. Enter Setpoint 1 Menu

Press aone time from run mode to get to

SP1

Setpoint 1.

Step 3. Enter the Setpoint 1 Value Submenu

Press d. Display shows the previous selection of Setpoint 1.

Step 4. Change the Setpoint 1 Value

Press bor cuntil desired value is displayed.

Step 5. Store the Setpoint 1 Value

Set the Setpoint 1 to 10 degree higher than Process value (SP1 = 85) and press dto store, display flashes

STRD

message and advances to

SP2

Setpoint 2 Menu.

Step 6. Store the Setpoint 2 Value

Repeat steps 3 and 4. Set the Setpoint 2 to 5 degree higher than Process value (SP2 = 80) and press dto store, display flashes

STRD

message and advances to

CNFG

Configuration Menu.

Step 7. Enter the Reading Config Menu

Press dto enter

RDG

Reading Config Menu.

Step 8. Enter the submenu items of Rdg Config Menu

Press dto display

SNSR

Sensor submenu: Sensor selection

for Autotune, Loop, or Ramp and Soak

°F.°C

is for

temperature and

DRRh

is for Humidity

Step 9. Enter the submenu items of Rdg Config Menu

Press dto display Temp Unit submenu:

Step 10 Scroll thru selection for Temp Unit submenu

Press bto Scroll though the available selections of the Temperature Unit of your choice: °For °C.

Step 11. Store the Temperature Unit

Press d, display momentarily shows

STRD

the Unit has been stored and the instrument will go automatically to the next menu item.

Step 12. Enter the Filter Constant Submenu

Display shows

FLTR

Filter Constant Submenu.

Step 13. Display the Filter Constant Value Submenu

Press dto display the flashing, previously selected Filter Constant.

Step 14. Scroll through available Filter Constants

Press bto sequence thru Filter Constants

0001, 0002

0004, 0008, 0016, 0032, 0064

and

0128

Step 15. Store the Filter Constant

Press dmomentarily to store

0004

Filter Constant and the

instrument will automatically go to the next menu item.

Step 16. Enter Alarm 1 Menu

The display will show

ALR1

the top menu for Alarm 1. In the following steps we are going to enable Alarm 1, Deviation, Unlatch, Normally Open, Active Above, Enable at power-on and +2°F High Alarm i.e. Process Value > Setpoint 1 Value +2°F will activate Alarm 1.

• If Analog Output Option is installed and enabled, the controller will skip Alarm 1 Menu item to Analog Output.

• Alarm must be DISABLED if Ramp is ENABLED.

• Alarm1 will only work for Humidity, not Temperature.

MQS4007/0411

SPECIFICATION

SENSOR SPECIFICATIONS Relative Humidity Accuracy/Range:

±2% for 10 to 90% ±3% for 5 to 10% and 90 to 95% ±4% for 0 to 5% and 95 to 100%

Non-linearity: ±3% Hysteresis: ±1% RH Response Time:

8 sec, tau 63%

Repeatability: ±0.1% Resolution: 0.1%, 12bit

Temperature Accuracy/Range*:

±0.5°C for 5 to 45°C (±1°F for 41 to 113°F); up to ±1.5°C for -40 to 5°C and 45 to 124°C (up to ±2.7°F for -40 to 41°F and 113 to 257°F)

*NOTE: extended temp range is for Probe only, the Controller’s operating temp is 0-50°C

Response Time: 5 to 30 sec, tau 63%

Repeatability: ±0.1°C Resolution: 0.1°C, 14 bit METER SPECIFICATIONS Display:

4-digit, 9-segment LED,

• 10.2 mm (0.40") Red, green, and amber programmable colors for setpoint and temperature units.

Output 1

†

Relay 250 Vac @ 3 A Resistive Load, SSR, Pulse

Output 2†:

Relay 250 Vac @ 3 A Resistive Load, SSR, Pulse

†

Only with -AL Limit Alarm option

Options: Communication

RS-232 / RS-485

Excitation:

24 Vdc

@ 25 mA

Exc. not available for Low Power Option

Line Voltage/Power:

90 - 240 Vac ±10%,

50 - 400 Hz*,

or 110 - 375 Vdc, 4 W

* No CE compliance above 60 Hz

Low Voltage Power Option:

12 - 36 Vdc or 24 Vac**

±10%

, 3 W

** Units can be powered safely with 24 Vac

but No Certification for CE/UL are claimed.

Dimensions:

25.4 H x 48 W x 126.3 D mm (1.0 x 1.89 x 5")

Weight:

127 g (0.28 lb)

Approvals:

CE per EN61010-1:2001

Alarm 1 is designed to monitor the humidity value around Setpoint 1 and Alarm 2 is designed to monitor the temperature value around Setpoint 2.

DPiTH-i32 Monitor

CNiTH-i32-AL Limit Alarm

Humidity + Temperature

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of one (1) year from the date of purchase. In addition to OMEGA’s standard warranty period, OMEGA Engineering will extend the warranty period for four (4) additional years if the warranty card enclosed with each instrument is returned to OMEGA.

If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components which wear are not warranted, including but not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.

RETURN REQUESTS/INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.

FOR WARRANTY

RETURNS, please have the following information available BEFORE contacting OMEGA:

1. Purchase Order number under which the product

was PURCHASED,

2. Model and serial number of the product under

warranty, and

3. Repair instructions and/or specific problems

relative to the product.

FOR NON-WARRANTY

REPAIRS, consult OMEGA for current repair charges. Have the following information available BEFORE contacting OMEGA:

1. Purchase Order number to cover the COST of the

repair,

2. Model and serial number of product, and

3. Repair instructions and/or specific problems

relative to the product.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.

© Copyright 2011 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.

PATENT AND TRADEMARK NOTICE: This product is covered by one or more of the following patents: U.S. Pat. No. Des. 336,895; 5,274,577; 6,243,021 / CANADA 2052599; 2052600 / ITALY 1249456; 1250938 / GERMANY DE 41 34398 C2 / SPAIN 2039150; 2048066 / UK Patent No. GB2 249 837; GB2 248 954 / FRANCE BREVET NO. 91

12756. The “Meter Bezel Design” is a trademark of Newport Electronics, Inc. USED UNDER LICENSE. Other U.S. and International Patents pending or applied for.

This device is marked with the international caution symbol. It is important to read the Setup Guide before installing or commissioning this device, as the guide contains important information relating to safety and EMC.

WARNING: These products are not designed for use in, and should not be used for, patientconnected applications.

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OEMGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.

The information contained in this document is believed to be correct, but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.

TRADEMARK NOTICE:

omega.com

, , and ®are Trademarks of

OMEGA ENGINEERING, INC.

HUMd

YES/NO

tEMP

YES/NO

dEU

YES/NO

UNIt

YES/NO

CONFIGURATION

FLOW CHART

DESCRIPTION OF FRONT PANEL

The display may be RH, Temperature or Dewpoint readings depending on your Reading Configuration selections. Factory defaults are shown. Note: a

Dual Display unit allows the user to observe the Relative Humidity or Dewpoint (upper display) and Temperature Value (lower display), at the same time.

Disassembly Instruction:

If necessary, the unit may be removed from the panel and opened.

Warning: Disconnect all ac power from the unit before proceeding.

1. Make sure the AC power is disconnected.

2. Remove all wiring connections from the rear of the

meter. To remove power and input connectors bend the side panel detents on the case outward to release the connectors, then pull connectors from the meter.

3. To remove meter from the case, squeeze left and right sides of the bezel to release, then pull from case.

WIRING

Wire the instrument according to the figure shown below.

Warning: Do not connect ac power to your device until you have completed all input and output connections. This device must only be installed by a specially trained electrician with corresponding qualifications. Failure to follow all instructions and warnings may result in injury!

Refer to Operator’s Manual for important Input Probe Shield wiring notes

Connect the main power connections as shown in the figure below.

FUSE Connector Output Type For 115Vac For 230Vac DC

FUSE 1 Output 1 Relay 3 A(T) 3 A(T) FUSE 2 Output 2 Relay 3 A(T) 3 A(T) FUSE 3 Power N/A 100 mA(T) 100 mA(T) 100 mA(T) FUSE 4 Power N/A N/A N/A 400 mA(T)

This Quick Start Reference provides information on setting up your instrument for basic operation. The latest complete Communication and Operational Manual as well as free Software and ActiveX Controls are available at

www.omega.com/specs/iseries

or on the CD-ROM enclosed with your shipment.

SAFETY CONSIDERATION

This device is marked with the international Caution symbol.

The instrument is a panel mount device protected in accordance with EN61010-1:2001. Remember that the unit has no power-on switch. Building installation should include a switch or circuit-breaker that must be compliant to IEC 947-1 and 947-3.

SAFETY:

• Do not exceed voltage rating on the label located on the top of the instrument housing.

• Always disconnect power before changing signal and power connections.

• Do not use this instrument on a work bench without its case for safety reasons.

• Do not operate this instrument in flammable or explosive atmospheres.

• Do not expose this instrument to rain or moisture.

EMC:

• Whenever EMC is an issue, always use shielded cables.

• Never run signal and power wires in the same conduit.

• Use signal wire connections with twisted-pair cables.

• Install Ferrite Bead(s) on signal wire close to the instrument if EMC problems persist.

MOUNTING Panel Mounting Instruction:

1. Using the dimensions from the panel cutout diagram

shown above, cut an opening in the panel.

2. Insert the unit into the opening from the front of the panel, so the gasket seals between the bezel and the front of the panel.

3. Slide the retainer over the rear of the case and tighten against the backside of the mounting panel.

_____ Underline denotes factory default setup

START HERE

Button Function in Configuration Mode

• To enter the Menu, the user must first press

button.

• Use this button to advance/navigate to the next menu item. The user can navigate through all the top level menus by pressing a.

• While a parameter is being modified, press ato escape without saving the parameter.

• Press the up bbutton to scroll through “flashing” selections. When a numerical value is displayed press this key to increase value of a parameter that is currently being modified.

• Pressing the bbutton for approximately 3 seconds will speed up the rate at which the set point value increments.

• In the Run Mode, pressing the b button changes display from RH readings to Temperature readings.

• Press the down c button to go back to a previous Top Level Menu item.

• Press this button twice to reset the controller to the Run Mode.

• When a numerical value is flashing (except set point value) press cto scroll digits from left to right allowing the user to select the desired digit to modify.

• When a setpoint value is displayed press c to decrease value of a setpoint that is currently being modified. Pressing the c button for approximately 3 seconds will speed up the rate at which the setpoint value is decremented.

• In the Run Mode, pressing the c button changes from RH readings to Dewpoint readings.

• Press the enter d button to access the submenus from a Top Level Menu item.

• Press d to store a submenu selection or after entering a value - the display will flash a

STRD

message to confirm your selection.

• In the Run Mode, press d twice to enable Standby Mode with flashing

STBY

CONFIGURATION

The instrument has two different modes of operation. Run Mode: used to display Temperature and Relative Humidity. Menu Configuration Mode: used to navigate through the menu options and configure the controller.

(UP)

(DOWN)

ENTER

123 45 6 78

Rear View

Relative Humidity

Display

%RH

1 Output 1/Setpoint 1/ Alarm 1 indicator

2 Output 2/Setpoint 2/ Alarm 2 indicator °C °C unit indicator for Temperature or Dewpoint °F °F unit indicator for Temperature or Dewpoint

%RH Display shows the Percent Relative Humidity

D Display shows the Dewpoint

Changes display to Configuration Mode and advances through menu items*

Used in Program Mode:

Accesses submenus in Configuration Mode

and stores

selected values*

Output 1 and 2 are for -AL Limit Alarm Option only.

1/4 2/5 3/6

WHITE

BLACK

GREEN

RED

N/C

SHIELD