OLYMPUS Mju-300 Digital, Mju-400 Digital Repair Procedure v1
µ-10/µ [mju:] 300/Stylus 300 DIGITAL
D. REPAIR PROCEDURE
µ-20/µ [mju:] 400/Stylus 400 DIGITAL
D. REPAIR PROCEDURE
[1] CONFIRMATION AND UPGREAD OF THE FIRMWARE.......................................... D-2
1. HOW TO CONFIRM FIRMWARE ....................................................................... D-2
2. HOW TO REWRITE FIRMWARE ....................................................................... D-2
[2] STATUS INDICATION
1. PREPARATION FOR THE INDICATION .............................................................D-3
2. STATUS INDICATION ......................................................................................... D-3
D-1
Ver.1
µ-10/µ [mju:] 300/Stylus 300 DIGITAL
D. REPAIR PROCEDURE
µ-20/µ [mju:] 400/Stylus 400 DIGITAL
[1] The confirmation and the upgrade of the firmware
1: The cofirmation procedure of the firmware
A lens barrier is opened under the condition that a card cover is opened. It confirms that the warning of “CARD-COVER
OPEN” is indicated on TFT, and a DISPLAY button and OK button are pushed at the same time. Open/close of the lens
barrier are done again after it waits for about ten seconds when it doesn't react to open/close of the barrier. ( When
warning isn't indicated on TFT. ) A firmware version is indicated on TFT when the buttons are pushed in the order of the
(Arrow) → (Arrow) → (Arrow) → (Arrow) → 1st Release → 2nd Release → (Arrow).
Ex.)
B:1004
U:1051
C:1011
→ (BOOT AREA: Ver1.004)
→ (USER AREA: Ver1.051)
→ (CISC : Ver1.011)
2: Upgrade procedure of the firmware
In case that BOOT AREA is upgraded : “S007xxxx.bin” is put in “dcolymp” folder of the xD picture card, and a camera is
turned on.
In case that USER AREA is upgraded : “E007xxxx.bin” is put in “dcolymp” folder of the xD picture card, and a camera is
turned on.
File name
S007xxxx.bin
E007xxxx.bin xxxx means a version number of the firmware.
2-1:
A “dcolymp” folder is made in the xD picture card that a format is done by µ-10/20, µ [mju:] 300/400, Stylus 300/400.
“E007xxxx.bin” (or/and “S007xxxx.bin”) is/are put in “dcolymp” folder of the xD picture card. (xxxx means a version number
of the firmware)
There is no limitation if it is a xD picture card which can be used with µ-10/20, µ [mju:] 300/400, Stylus 300/400.
2-2:
An AC adapter is connected under the condition that the lens barrier is closed without the batteries. Then a the xD picture
card is inseted to the camera.
2-3:
A barrier is opened under the condition that OK button is pressed and held. When upgrade is started, red LED is turned
on. Then OK button is released.
2-4:
When upgrade is completed, red LED blinks.
2-5:
The firmware version is confirmed by above (1:).
D-2
Ver. 1
µ-10/µ [mju:] 300/Stylus 300 DIGITAL
µ-20/µ [mju:] 400/Stylus 400 DIGITAL
D. REPAIR PROCEDURE
[2] Status indication
1: Preparation for the indication
1-1: In case of REC mode
A lens barrer is opened under the condition that AC adapter is connected and card door is opened. It confirms that the
warning of “CARD-COVER OPEN” is indicated on TFT, and a DISPLAY button and OK button are pushed at the same
time. The following information is indicated on TFT.
OLYMPUS
U10D
S300D Product Name
U300D
NTSC VIDEO-OUT (NTSC / PAL)
JPANESE LANGUAGE (JAPNESE / ENGLISH)
1-2: In case of PLAY mode
A DISPLAY button is pushed under the condition that AC adapter is connected and card door is opened. Under the
condition that warning is indicated on TFT, a zoom lever is operated with pushing OK button in the order of T
Center. Then OK button is released. The above information (1-1) is indicated on TFT.
→ W →
2: Status indication
It continues in 1-1 (or 1-2), the buttons are pushed in the order of (Arrow) → (Arrow) → (Arrow) → (Arrow)
→ 1st Release → 2nd Release.
2-1: Firmware version
The following information is indicated on TFT when (Arrow) button is pushed after the above process.
Ex.)
PAGE1
B:1004
U:1051
C:1011
2-2: Release/Flash luminous number of times
The following information is indicated on TFT when
Ex.)
PAGE2
R:000026
S:000018
→ (BOOT AREA: Ver1.004)
→ (USER AREA: Ver1.004)
→ (CISC : Ver1.004)
(Arrow) button is pushed.
→ (Release number of times)
→ (Flash luminous number of times)
2-3: Serial number
The following information is indicated on TFT when
Ex.)
PAGE3
CS : 107000607 → (Serial number of Body)
MCS: 0042202000249001
→ (Serial number of MC-PCA2)
Ver.1
(Arrow) button is pushed.
D-3
µ-10/µ [mju:] 300/Stylus 300 DIGITAL
D. REPAIR PROCEDURE
µ-20/µ [mju:] 400/Stylus 400 DIGITAL
2-4: Damage Code
The following information is indicated on TFT when (Arrow) button is pushed.
Ex.)
D:
1E13
→ (Damage Code)
XXXX
XXXX
XXXX
XXXX
XXXX
A damage code is indicated by four-digit hexadecimal after "D:", and a memory is done to five maximums. (A top tier is the
latest damage code.)
2-4-1: Detail of Damage Code (Refer to a damage code list.)
Ex.) 1E 13 ----------- “Zoom Lens Reset Error”
Lower two digits Status(Row) 0 x 13
Upper two digits Status(Row) 0 x 1E
Block Status Error Damage Media
Error
0x06 PARAMDT_NOT_SUPPORTED
0x07 PARAMDT_OS_ERROR
MEC_STATUS 0x1EXX
0x10 MEC_RESLENS_FCS_ERROR - - - Focus Lens Reset
0x11 MEC_RESLENS_ZOOM_ERROR - - - Zoom Lens Reset
0x 12 MEC_RESLENS _FCS_ERROR_DMG
0x 13 MEC_RESLENS _ZOOM_E RROR_DMG
0x20 MEC_IRISMOT_TIMER_DELAY
RECPROC_STATUS 0x 1FXX
0x 21 RECPROC_RECJPEG_ERROR - - - Unus ual Paramet er
2-4-2: Erasure of the damage code
OK button is pushed under the condition that a damage code is indicated on TFT. Damage code is erased when a lens
barrier is closed.
○
○
◎
◎
○
- - Parameter injustice or
- - Queue R/W injusti ce,
- - Focus Lens Reset
- - Zoom Lens Reset
- - Iris Motor Timer Delay
Play
Mode
Not e
un-support
OS Error
Error
Error
Error
Error
D-4
Ver. 1
Loading...