Please read the Operational Manual
before attempting to use this product.
Super Low Lux DNR Vandal Proof Dome Camera
Operational Manual
Digital Noise Reduction
Mechanical IR
Cut Filter
Removable (ICR)
This color video camera employs a 1/3 inch CCD solid-state imaging device with 470/410K picture elements. This unit is equipped
with a newly developed DNR DSP
technology which suppresses all significant noise while AGC is activated. So the camera is able to deliver a smooth and more
even picture that has enhanced readability and saves video storage space.
The Digital Noise Reduction technology is built into the camera to eliminate any noise associated with low light environment.
Ghost and blooming effects are reduced dramatically, leaving the image clean and vivid. An added benefit is that the HDD
required for DVR recording is substantially reduced by up to 70%, due to the DNR technology. Sturdy and IP66 enclosure
ensures the camera to stay in its best condition even under the most critical environments.
For using 12V DC power adaptor, please use 1000mA for each SDMIV35 and 500mA for each SDVD.
UL with Regulator.
FEATURES
SDMIVD35-55AIDN/SDMIVD35-55AIDNP
z 1/3” Sony Super HAD CCD
z 550 TV Lines
z 35 IR LED
z IR Distance 65~80ft / 20~25m
z 3.0mm~12.0mm Auto Iris Lens / F1.4
Lens Made in Japan (Tamron)
z Advanced Digital Noise Reduction (DNR)
z Mechanical IR Cut Filter Removable (ICR)
z IR Accuracy: Vivid color performance in the daytime and
sharp B/W image with no focus shift in the nighttime
z IP66 Rating, Heavy-duty, weather & vandal proof
z Built-in horizontal/vertical adjusting mechanism for multi-
dimensional adjustment
z Advanced wide range Auto Tracing White Balance (ATW),
automatically adjusts the white balance according to the
color temperature in the environment
z Smart digital control Auto Back Light Compensation (BLC)
z Outstanding Signal to Noise Ratio Better than 50dB
z Special Distortion-free Acrylic Vandal Dome Cover
z Dual Power 12V DC / 24V AC Auto Select
P = PAL Version
35 IR Day & Night ICR 550 TVL
SDMIVD35-55AIDN
SDMIVD35-55AIDNP
(Digital Signal Processor) for video processing. The DNR function is a newly developed
Hi-Res. 550 TVL
SDVD-55AIDN
SDVD-55AIDNP
SDVD-55AIDN/SDVD-55AIDNP
z 1/3” Sony Super HAD CCD
z 550 TV Lines
z 3.0mm~12.0mm Auto Iris Lens / F1.4
Lens Made in Japan (Tamron)
z Advanced Digital Noise Reduction (DNR)
z IP66 Rating, Heavy-duty, weather & vandal proof
z Built-in horizontal/vertical adjusting mechanism for
multi-dimensional adjustment
z Advanced wide range Auto Tracing White Balance
(ATW), automatically adjusts the white balance
according to the color temperature in the
environment
z Smart digital control Auto Back Light Compensation
(BLC)
z Outstanding Signal to Noise Ratio Better than 50dB
z Special Distortion-free Acrylic Vandal Dome Cover
z Dual Power 12V DC / 24V AC Auto Select
SDMIVD35-55AIDN_ SDVD-55AIDN_rev09192008 1
PARTS AND FUNCTIONS
A. Camera
B. Bracket
C. Bottom Housing
D. Vari-Focal Lens
E. Safety String
F. Upper Housing
G. Screw Hole
H. Cable Hole
I. LED Board
J. Control Board
I. Power Source: 12V DC / 24V AC (Non-polarity) Block Terminal
II. Video Out
III. DC Auto Iris Level Adjustment - Adjusting DC drive auto
iris lens driving level for obtaining correct exposure light
IV. RCA Video Out
Factory Default
SDMIVD35-55AIDN_ SDVD-55AIDN_rev09192008 2
INSTALLATION
Step 1: Camera Cabling
A. Decide how the camera will be mounted.
B. Decide how the cable will be connected to the camera.
a. Using ½” pipe from the side
b. Using the cable hold at the base of the camera with or without pipe
C. Be sure to use proper waterproofing process regardless of what method you use to connect the cable.
NOTE: Warranty will be VOIDED if camera is damaged by water or moisture due to improper installation without waterproofing.
Step 2: Removing Dome Cover
Remove dome cover from the main body by loosening the four dome cover mounting
screws. The dome cover is fixed with tamperproof screws. Loosen the four dome cover
mounting screws by using the supplied bit for tamperproof screws.
Step 3: Securing Camera
Place mounting plate at position which the camera will be mounted and fix the screw holder and then screw 4x 26mm screws x4.
Step 4: Focus & Angle Adjustment
We have provided a service monitor RCA connection jack for your convenience.
SDMIVD35-55AIDN_ SDVD-55AIDN_rev09192008 3
A. Focus Adjustment – The default setting for zoom position is WIDE.
x IR Day & Night ICR Focus Adjustment:
o Loosen the zoom ring thumbscrew
o Turn the zoom ring to set to the desired zoom
o Tighten the zoom ring thumbscrew
o Use the screw driver to loosen the focus ring thumbscrew
o Turn the IR LED board to set to the desired focus
o Use screw driver to tighten the focus ring thumbscrew
x Hi-Res. Focus Adjustment:
o Loosen the zoom ring thumbscrew
o Turn the zoom ring to set to the desired zoom
o Tighten the zoom ring thumbscrew
o Loosen the focus ring thumbscrew
o Turn the focus ring to set to the desired focus
o Tighten the focus ring thumbscrew
B. Angle Adjustment
3-AXIS mechanical design allows 90° side views for wall mount and furthest angle for ceiling mount when guarding a
hallway. Horizontal angle adjustment: Turn the platform to adjust the horizontal angle 180°~300°. Vertical angle
adjustment: Turn the platforms to adjust the vertical angle 90°.
Step 5: Auto Iris Level Adjustment
You will need to set the level volume when shooting in the condition described below.
x If shooting simultaneously in a dark room and through a bright window
x If the subject background is extremely bright or dark
x If the brightness of the picture on the monitor is not correct
L (counter-clockwise) to decrease the contrast
H (clockwise) to increase the contrast
SDMIVD35-55AIDN_ SDVD-55AIDN_rev09192008 4
Step 6: Function Setting
Factory Default
You can select the function according to your condition. Please see the above image for factory default values whenever a
camera needs to be set to default again during an installation.
Auto Iris and AES Adjusting – Dipswitch 1 (IR D&N ICR & Hi-Res.)
Please select the Auto Electronic Shutter mode to control exposure with the electronic shutter. The range of shutter speed is from
1/50 (1/60) set to 1/100,000 sec.
Flickerless Function Adjusting – Dipswitch 2 (IR D&N ICR)
If a camera is installed into a different frequency, the Flickerless function will reduce the flicker of video. The shutter of NTSC is
1/100; shutter of PAL is 1/120. When the dip switch is at AES/FL side, the shutter will stay at Flickerless situation.
AGC – Dipswitch 3 (IR D&N ICR) / Dipswitch 2 (Hi-Res.)
If you are to install the camera in a low lux environment, switch to AGC so that it will increase the camera sensitivity. The default
setting is AGC.
White Balance Adjusting – Dipswitch 4 (IR D&N ICR) / Dipswitch 3 (Hi-Res.)
AWB mode – Conventional auto white balance – This mode is factory default setting
ATW mode – Advanced white balance – This mode is limited (color temperature 2500°K~9000°K
Auto Back Light Compensation – Dipswitch 5 (IR D&N ICR) / Dipswitch 4 (Hi-Res.)
This intelligent auto BLC is a newly developed digital light level control system. It is activated automatically by screen histogram
(contrast) and 225 area window weighing integration to control iris gain and white balance simultaneously.
Central Window Weighted average Back Light Compensation
This method is suited for cases where the main subject is fixed within the screen.
Histogram Back Light Compensation
This method is suited for cases where the main subject moves about within the screen.
Mirror Adjusting – Dipswitch 6 & 7 (IR D&N ICR) / Dipswitch 5 & 6 (Hi-Res.)
If the camera is installed in elevators, lifts or viewing directly to a mirror, please adjust to horizontal mirror mode. If the camera
must be installed upside down due to installation limit, please adjust to vertical mirror mode.
SDMIVD35-55AIDN_ SDVD-55AIDN_rev09192008 5
Day & Night Adjusting
The smart day and night mechanical filter removable allows changing between color and monochrome mode, and the user could
define the filter to work correctly during the daytime and nighttime.
Day and Night Filter Automatic mode:
***Note: The D&N should be at “on” position. Make sure the AGC/Sense-up is at “on” position. If the switchers are at
AGC/Sense-up “off”, the filter will stay at daytime position.
Sense-up Adjusting – Dipswitch 10 (IR D&N ICR) / Dipswitch 7 (Hi-Res.)
Sense-up stands for frame integration that is useful for the low lux environment. The default sense-up rate is 4x similar 1/15 sec.
Video / Color Adjusting – Dipswitch 8 (IR D&N ICR)
IR Adjusting – Dipswitch 9 (IR D&N ICR)
IR on/off switch.
Step 7: Reinstall the Dome Cover
Reinstall the dome cover to the main body by tightening the four cover mounting screws.
LIST OF COMPONENTS
z One (1) SDMIVD35-55AIDN/SDMIVD35-55AIDNP or
SDVD-55AIDN/SDVD-55AIDNP Camera with video/power cable
z Five (5) Camera Mounting Screws
z One (1) Tamperproof L-Shaped Screw Driver
z One (1) Mounting Template Sticker
z One (1) Operational Manual
* For any returns, please include all components
listed above with original packaging in Resalable
Condition. Absolutely No Returns will be
accepted if any component is missing/damaged.
SDMIVD35-55AIDN_ SDVD-55AIDN_rev09192008 6
GENERAL SPECIFICATIONS
Model SDMIVD35-55AIDN SDMIVD35-55AIDNP SDVD-55AIDN SDVD-55AIDNP
TV System NTSC PAL NTSC PAL
Image Sensor 1/3” Sony Super HAD CCD
Picture Elements 768(H) x 494(V) 752(H) x 582(V) 768(H) x 494(V) 752(H) x 582(V)
Scanning System 525 lines 2:1 Interlace 625 lines 2:1 Interlace 525 lines 2:1 Interlace 625 lines 2:1 Interlace
Sync System Internal Lock / Line Lock
Horizontal Resolution 550 TV Lines
Minimum Illumination
Lens
0.1 Lux @ F1.2 (30 IRE, AGC on)
0.001 Lux @ F1.2 (B/W mode, AGC on, Sense-up on)
0 Lux under Infrared Illumination
3.0mm~12.0mm Auto Iris Lens / F1.4
Lens Made in Japan (Tamron)
0.01 Lux @ F1.2 (B/W mode, AGC on, Sense-up on)
0.1 Lux @ F1.2 (30 IRE, AGC on)
Infrared Wavelength From 780~1100nm None
D&N Switch Delay Time 5~8 sec. None
Color/Mono Switching Chain Reaction with D&N Filter None
Frame Integration 4x Factory Default (2x~32x Customization) None
Infrared LED 35pcs None
IR Distance 65~80ft / 20~25m None
Digital Noise Reduction Automatic
Gamma 0.45
Function Dipswitch Board in Dome Camera
AGC Auto Gain 36dB On (36dB) / Off
S/N Ratio Better than 50dB
White Balance ATW (2500°K~9000°K) / AWB
ALC ALC (1/60) / AES ALC (1/50) / AES ALC (1/60) / AES ALC (1/50) / AES
BLC On / Off
H Mirror Function On / Off
V Mirror Function On / Off
Sense-up On (4x) / Off
Video / Color On / Off None
Day/Night Control On / Off None
IP Rating IP66
Video Output Signal Composite: 1.0V p-p @ 75 Ohm
Operating Temperature 14°F ~ 122°F / -10°C ~ 50°C
Power 12V DC / 24V AC (Auto Select)
Power Consumption
12V DC
Power Consumption
24V AC
Max Average 210~470mA (Start up 850mA) Max Average 180~200mA (Start up 400mA)
230mA (Start up 400mA) 180mA~200mA (Start up 200mA)
Dimensions 610”(D) x 4.02”(H) / 155(D) x 102(H) mm
*Specifications are subject to change without notice
SDMIVD35-55AIDN_ SDVD-55AIDN_rev09192008 7
1. Never point the camera toward the sun.
2. Handle this camera with care.
3. Requires a proper operating environment.
4. Clean the front face to the pick-up device.
5. Check the power source voltage.
6. Objects and liquid entry.
7. Servicing.
8. Damage requiring service.
CAUTIONS
Do not expose the lens directly to the sun or to strong light as this may damage the pick-up device.
Avoid any shock or bumping of the camera. Improper handling could damage the camera.
This camera is designed for outdoor or indoor use. The allowable temperature range for operation of this camera is between 14°F ~ 122°F
/ -10°C ~ +50°C and the allowable humidity is 85%RH maximum.
It is recommended that the pick-up device surface be cleaned before lens installation or whenever the lens is changed. Cleaning should be
done by using a chamois, a very fine soft cloth, lens tissue, or cotton tipped applicator and ethanol to carefully remove any fingerprint or
dust.
The power source voltage should be within the specified range (must meet the specifications). Camera must be connected to a surge
protector at all times.
Never push objects of any kind into this camera as this may touch dangerous voltage points of short out parts that could result in a fire or
electric shock. Never spill any kind of liquid on the video product.
Do not attempt to service this video product by yourself as opening or removing covers may expose you to dangerous voltage or other
hazards. Refer all service to qualified servicing personnel.
Unplug this video product from the wall outlet and refer service to qualified servicing personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been dropped or the cabinet has been damaged.
d. When the video product exhibits a distinct change in performance.
OK-I USA products are covered under warranty for one year from the date of purchase. The warranty will automatically be voided if any of the
following occurs:
1. Camera sticker is removed.
2. Camera is modified in any way.
3. Video or power cable is cut.
4. Damage by power surge.
WARRANTY
If the camera sticker is removed, we will not be able to confirm any information regarding when and where the product was purchased.
We have no other way to verify the purchase record without the serial number on the camera sticker; therefore, it should not be removed.
If the camera is scratched, damaged, or modified in a manner not described in this manual, the warranty will be voided immediately. It is
the customer’s responsibility to keep the camera in good condition.
The video cable and the power cable should not be tampered with. Cutting or modifying of the cables will result in termination of the
warranty.
The use of non-UL or unregulated power supplies/panels/transformers or adaptors will result in the termination of the warranty.
SDMIVD35-55AIDN_ SDVD-55AIDN_rev09192008 8
Loading...