Oki lp-1030-mf User Manual

Wide Format Printer

Teriostar LP-1030 Series

LP-1030-MF

User's Manual

for Multifunction Printer Operation

Chapter

1

Before Use

Chapter

2

Copy Function Preset Functions

Chapter

3

Submission

Function

Chapter

4

U00123006304

Chapter

5

Scan Function

Chapter

6

Troubleshooting

U00123006300 January, 2011

U00123006301 July, 2011

U00123006302 July, 2013

U00123006303 April, 2015

U00123006304 December, 2015

Copyright© 2015 OKI Data Infotech Corporation.

All rights reserved.

The contents of this manual may be changed without prior notice.

This product displays fonts created by TypeBank Co., Ltd. and ARPHIC TECHNOLOGY.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

The CE mark, that shows that the products sold in the EU are conformed to the requirements of EC directive,
is statutorily obliged to be axed to the products.
In each directive, the scope of directive to be applied to equipment is explicitly dened. Our company’s
product LP-1030 series conforms the EMC directive, low voltage directive and RoHS Directive.

Inquiry of CE mark:

OKI Europe Ltd.
Wide Format Division

Siemensstrasse 9 , D-63263 Neu-Isenburg
Germany
Tel: [phone]
Fax: [phone]

OKI Data Infotech Corporation

8 Nakase 1-chome, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan
Phone : [phone]
Fax : [phone]

Preface

Your Printer is a Teriostar LP-1030 Series wide format Printer (Referred to

as the Printer in this manual), and this manual describes how to operate

the Printer's copy, submission, and scan functions.

For details about the print function, paper setting, consumable

replacement, and paper jam clearance, see the separate User's Manual

for Basic Printer Operation.

To handle the Printer safely and correctly, be sure to read the Safety

Precautions carefully before use.

Keep this manual in a place where you can easily read it when required.

LP-1030-MF User's Manual for Multifunction Printer Operation

3

Safety Precautions

In this manual, the following symbols are used to alert the user to information that

will prevent damage to the Printer, and ensure its safe and correct use.

These symbols are explained below. Make sure that you thoroughly understand

the information. Always follow the instructions marked by these symbols.

Symbol Examples

Warning

Caution

If this information is ignored and the Printer is

handled incorrectly, it may result in serious injury or

death.

If this information is ignored and the Printer is

handled incorrectly, it may result in injury or machine

damage.

This symbol indicates that caution is required (includes dangers and

U

warnings).

The example on the left indicates a safety Warning or Precaution.

This symbol indicates a prohibited action.

The example on the left means Do not disassemble.

This symbol indicates required actions or instructions.

The example on the left means Disconnect the power plug from

the outlet.

4

LP-1030-MF User's Manual for Multifunction Printer Operation

Warning

Be very careful not to touch the fuser unit labeled HIGH TEMPERATURE inside

the Printer.

Burn injuries may result.

Do not disassemble or modify the Printer.

An accident or malfunction may result.

Do not heat a toner cartridge or a waste toner bottle containing waste toner, nor

place it into a ame.

It may burst or ignite, resulting in an accident or re.

Never use the Printer in a location exposed to abnormally high humidity or

moisture.

A re, electric shock, or malfunction may result.

Do not drop metal pieces such as staples, or spill water, or other liquids inside

the Printer or through gaps.

A re, electric shock, or malfunction may result.

Do not connect or disconnect the power cord or other parts with wet hands. An

electric shock may result.

In the following situations, turn o the power, and disconnect the power plug

from the outlet. If you continue using the Printer in an abnormal condition, an

accident or re may result.

When cleaning

When an abnormal odor, noise, or smoke is emitted

When foreign matter such as metal pieces or water get inside the Printer

or through gaps

When a problem that must be repaired by the service representative

occurs

Connect the power plug separately to a power socket with a rated voltage

of 120V and a rated current of 12A or more, or to a power socket with a rated

voltage of 230V and a rated current of 8A or more. To prevent a re or electric

shock, avoid the sharing of power with other equipment.

LP-1030-MF User's Manual for Multifunction Printer Operation

5

Be sure to remove the dust on the power plug and the socket. Do not use a

dusty plug as a current leak due to humidity on its surface may heat the plug

and result in re.

Do not x, twist, bind, modify, stretch, or bend excessively the power cord. Do

not put heavy object on it. A damaged power cord may heat and result in re or

electrical shock.

If the power cord is cut or if the wires are exposed, ask a service representative

for replacement.

Using a damaged power cord may result in re or electrical shock.

Caution

Do not disassemble or modify the toner cartridge.

The toner on your skin will have a negative eect.

If ink stains your skin or clothing, wash with soap and water immediately.

To prevent a toner leakage, do not drop the toner cartridge nor expose it to strong

impacts.

If toner gets into your eyes, do not rub your eyes, and wash the toner out. Visit a

doctor immediately.

As the roll paper is heavy, handle it carefully to make sure that you do not drop it.

Dropping the roll paper on your feet may result in injury.

When installing the roll paper, use the cutter to cut the end of the paper. At this

time, be careful not to injure yourself on the cutter.

Install the Printer close to a power outlet. Make sure the outlet is easy to reach in

case the power plug needs to be disconnected in an emergency.

When connecting and disconnecting the power cord, hold it by the plug or

connector.

To prevent a re, electric shock, or malfunction, avoid pulling the cord.

6

LP-1030-MF User's Manual for Multifunction Printer Operation

If you use a power strip, change it for a new one at least once a year.

Do not use an extension cable or an adapter plug.

Once a month, turn the power switch o and inspect the followings. Contact your

service representative if you detect any problem.

The plastic insulator at the base of the plug's pins does not suer from heat

deformation.

The plug's pins are not bent or covered by rust.

There is no dust between the plug's pins.

The power cord is not frayed and the energized wires are not exposed.

The plug is rmly plugged into the socket.

There is no dust on the plug or the socket.

Before moving the Printer from its current installation location to another location,

contact your service representative.

In addition to the items above, obser ve the warnings and precautions in each

section of the manual.

LP-1030-MF User's Manual for Multifunction Printer Operation

7

Reading the Manual

TIP

Notations

Indicators

Warning

Describes information equivalent to a Warning in a safety precaution.

Caution

Describes information equivalent to a Caution in a safety precaution.

Note

Describes the information to be noted on handling the Printer.

The Tip indicator.

Indicates useful information, supplementary operation, or other information.

(& page) The Reference indicator.

The reference section or page is shown after this indicator.

8

LP-1030-MF User's Manual for Multifunction Printer Operation

Preface

Table of Contents

Chapter

1

Before Use

TCopy Restrictions .........................................................................................14

TAbout the Multiple Functions ...................................................................15

Print Function ........................................................................................................................ 15

Copy Function ....................................................................................................................... 15

Submission Function ......................................................................................................... 15

Scan Function ........................................................................................................................ 15

TMain Functions ............................................................................................16

TAbout Originals ...........................................................................................19

Scannable Original Conditions ....................................................................................19

Unscannable Originals ...................................................................................................... 19

Using Carrier Sheets with Originals ..........................................................................20

Guaranteed Image Scan Range .................................................................................. 21

TLoading the Original ...................................................................................22

Loading the Original .......................................................................................................... 22

Canceling Original Scanning ........................................................................................ 24

TRegular Cleaning .........................................................................................26

Cleaning the Shading Guide and Scanner Glass ..............................................26

LP-1030-MF User's Manual for Multifunction Printer Operation

9

Chapter

2

Copy Functions

TCopy Operation Flow ..................................................................................28

TCopy Function Overview ...........................................................................30

TSelecting the Original Type .......................................................................31

TAdjusting the Density .................................................................................32

TSelecting the Paper Position .....................................................................33

TSelecting the Original Size ........................................................................34

TSelecting the Original Size Standard ....................................................... 38

TSelecting the Original Output Direction ................................................39

TPartial Copying ........................................................................................... 40

TAdjusting the Background ........................................................................42

TAdjusting the Original's Contrast .............................................................43

TAdjusting the Original's Sharpness......................................................... 44

TPerforming White on Black Reverse ........................................................45

TSetting the Scale ......................................................................................... 46

TAdding Blank Space ....................................................................................47

TSelecting the Paper Type .......................................................................... 48

TCentering scan image .................................................................................49

TErasing the Frame .......................................................................................50

TSelecting the Paper Output Slot ..............................................................51

TPerforming Mirror Reverse ........................................................................52

TEntering the Number of Copies ................................................................53

TPerforming a Moderate Scan ....................................................................54

TCopying an Original with Text & Lines ....................................................55

TCopying a Blueprint Original ....................................................................56

TSorting ........................................................................................................... 57

TSorting Flow .................................................................................................58

TTest Printing Sorted Originals ................................................................... 61

TAdditionally Copying the Sorted and Printed Originals ......................62

TInitializing the Setting ................................................................................63

THandling copy jobs .................................................................................... 64

TAdditionally copying the Copied Originals ............................................65

10

LP-1030-MF User's Manual for Multifunction Printer Operation

Chapter

3

Submission Functions

TSubmission Functions Outline ..................................................................68

TPreparing the network and host computer ...........................................70

Checking the Printer's Network Connection ......................................................70

Creating a Shared Folder .................................................................................................70

Preparing a printer to receive submissions .........................................................71

TSubmission Operation Flow ......................................................................72

Submitting images (SMB connection) ....................................................................72

Submitting images (FTP connection) .....................................................................75

Storing image data in the submission job box ................................................. 78

Submitting thumbnails ....................................................................................................80

Submitting to a printer ....................................................................................................82

TSubmission Function Overview ............................................................... 84

TSelecting Scan Color Mode .......................................................................85

TSelecting Original Type ..............................................................................86

TSelecting Scan Resolution .........................................................................87

TSelecting the File Format for Images to be Scanned ...........................88

TConguring the Filename for Images to be Scanned ..........................90

TSubmission and Copy in One Operation ................................................92

TPrint Copies ..................................................................................................93

TPrint Quality .................................................................................................94

THandling Image Submission Jobs ............................................................95

THandling Printer Submission Jobs ...........................................................96

TReprinting through Printer Submission .................................................97

LP-1030-MF User's Manual for Multifunction Printer Operation

11

Chapter

4

Preset Functions

TPresets Overview ...................................................................................... 100

TCreating a preset in the Memory ...........................................................101

TCalling a Preset from the Memory .........................................................102

TSaving Settings as Default Settings .......................................................103

TChanging a Preset Name ........................................................................ 104

TCreating a Preset in the Memory for a Submission Destination ..... 105

Chapter

5

Scan Functions

TScan Functions Outline ........................................................................... 108

TPreparing the network and host computer ........................................ 109

Checking the Printer's Network Connection ................................................... 10 9

Installing the Exclusive Application (TerioStation) ........................................ 109

Conguring the Exclusive Application (TerioStation) ................................. 109

TChecking Operating Status with Message ........................................... 110

Chapter

6

Troubleshooting

TUnclear Copying or Scanning .................................................................115

TCannot Copy or Scan as Expected .........................................................118

TImproper Submission ...............................................................................122

12

LP-1030-MF User's Manual for Multifunction Printer Operation

Chapter

1

Before Use Copy Function

Chapter

1

Before Use

Chapter 1 describes the information required for operating the Printer. Be sure to

understand the basic information described in this chapter before moving to the

next chapters.

Chapter Contents

Copy Restrictions ...................................................................................14

T

About the Multiple Functions .............................................................. 15

T

Main Functions .......................................................................................16

T

About Originals ......................................................................................19

T

Loading the Original..............................................................................22

T

Regular Cleaning ....................................................................................26

T

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

13

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Copy Restrictions

Depending on the subject matter, copying may be restricted or prohibited by law.

<Items restricted by law>

- Government-issued banknotes, coins, securities, government bonds, local

government bonds (including items marked as samples)

- Banknotes, coins, or securities in circulation in other countries

- Unused postage stamps or postcards without government copying

permission from the government

- Government-issued payment stamps, or securities restricted by law

- Other items prohibited by related laws

<Items treated with discretion>

- Privately-issued securities (such as stocks, bills, checks), commuter tickets.

Other than the minimum copying required for companies to use in their

operations, the government advises caution.

- Also, it is better to think items such as government-issued passports, licenses

issued by public or private bodies, permits, ID cards, trac tickets, and food

tickets should not be copied.

Chapter

5

Chapter

6

<Copyrighted items>

- The copying of copyrighted items such as novels, music, paintings, prints,

maps, drawings, movies, and photographs is prohibited except for personal

or household use, or within a scope based on such use.

14

LP-1030-MF User's Manual for Multifunction Printer Operation

About the Multiple Functions

The Printer is equipped with print, copy, submission, and scan functions. Select a

function by pressing the corresponding button.

Print Function

Prints after receiving data created on a workstation, or personal computer (referred

to as computer in this manual).

For more details, see the separate User's Manual for Basic Printer Operation.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Copy Function

Copies in accordance with the type and image quality of the original.

For more details, see Chapter 2.

Submission Function

Submits image data scanned with the Printer to the computer's shared folder.

For more details, see Chapter 3.

Scan Function

Sends image data scanned with the Printer to the computer connected to the

network using the exclusive application.

For more details, see Chapter 5.

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

15

Chapter

Text & LinesText/PhotoPhoto Blueprint

Original with Background Color

High Normal Low

234

1

Before Use Copy Function

Main Functions

This section describes the main functions for copying and submission.

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Copying/submitting

after selecting the

appropriate original

type (& page 31

and & page 86 )

Copying/submitting

after deleting

background color from

the original

(& page 42 )

Copying/submitting

after adjusting the

density

(& page 32 )

Copying after scaling

(& page 46 )

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

1

4-R2.0

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

A

B

C

D

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

234

K

MODEL

TITLE

PART NO.

DRAWING NO.

A

B

C

D

1

4-R2.0

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

1

4-R2.0

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

50.0

50.0

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

1

4-R2.0

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

Same

234

K

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

Custom

234

K

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

130%

A

B

C

D

SHEET

PAGE

234

K

50.0

XXXXXXXXX

MODEL

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

50.0

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

XXXXXXXXXXXXXXXXXXXX

50.0

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

50.0

SHEET

PAGE

Place Name (Japanese) Hawaii (USA, State of Hawaii)

Place Name (English) State of Hawaii

Capital Honolulu (State Capital)

Area 16634 square kilometers

Population 1211537 (2000)

Time Zone JST -19 hours

For example, noon on Sunday in Hawaii

is 7am on Monday in Japan

1

234

4-R2.0

K

MODEL

TITLE

PART NO.

DRAWING NO.

A

B

C

D

SHEET

PAGE

A

B

C

D

A

B

C

D

SHEET

PAGE

50.0

XXXXXXXXX

123456789

123456789 A4

50.0

XXXXXXXXXXXXXXXXXXXX

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

110%

A

B

C

D

SHEET

PAGE

1

A

4-R2.0

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

Fixed

1

234

4-R2.0

K

50.0

XXXXXXXXX

MODEL

UNIT

1/1

TITLE

CHECKED BY SIGNED BY DRAWN BY

PART NO.

123456789

DRAWING NO.

123456789 A4

A4A3(141%)

234

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

50.0

XXXXXXXXXXXXXXXXXXXX

1

234

A

4-R2.0

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

1

234

A

4-R2.0

B

50.0

K

C

50.0

D

XXXXXXXXX

MODEL

UNIT

SCALE

XXXXXXXXXXXXXXXXXXXX

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

123456789

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design Department

123456789 A4

1

A

A

B

50.0

C

D

SHEET

PAGE

A

B

C

D

SHEET

PAGE

4-R2.0

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

Proportional

1

234

A

4-R2.0

B

K

C

D

MODEL

SCALE

UNIT

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design Department

113.5%

K

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

50.0

XXXXXXXXX

123456789

123456789 A4

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

XXXXXXXXXXXXXXXXXXXX

A

B

50.0

K

C

50.0

D

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

SHEET

PART NO.

123456789

PAGE

DRAWING NO.

123456789 A4

A

B

C

D

SHEET

PAGE

A

B

50.0

C

D

SHEET

PAGE

A

B

50.0

C

D

113.5%

SHEET

PAGE

16

LP-1030-MF User's Manual for Multifunction Printer Operation

Copying after adding

O On

O On

blank space to the

top and bottom of the

original

(& page 47 )

Copying the original

partially

(& page 40 )

Copying after deleting

the frame

(& page 50 )

Copying/submitting

after adjusting the

original's contrast

(& page 43 )

Non-Standard Size Original

1

A

4-R2.0

B

C

D

Paper Feed
Direction

E E

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

A

B

C

D

E E

1

234

A

4-R2.0

B

K

C

50.0

D

MODEL

SCALE

UNIT

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design Department

DarkMedium Light

1

234

A

4-R2.0

B

K

C

D

MODEL

UNIT

SCALE

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design Department

Paper Feed
Direction

234

K
K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789

1

4-R2.0

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

50.0

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

50.0

50.0

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

A

B

C

100.0

D

SHEET

PAGE

A4 long

234

K
K

50.0

XXXXXXXXX

MODEL

TITLE

PART NO.

123456789

DRAWING NO.

123456789

A

B

C

D

SHEET

PAGE

A

B

C

D

SHEET

PAGE

XXXXXXXXXXXXXXXXXXXX

100.0

SHEET

PAGE

A4 long

A

B

C

D

A

B

C

D

1

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

4-R2.0

Partial copy
start position

Partial copy
length

234

A

B

50.0

K

C

50.0

D

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

SHEET

PART NO.

123456789

PAGE

DRAWING NO.

123456789 A4

1

234

A

4-R2.0

B

K

C

100.0

K

D

50.0

E E

XXXXXXXXX

MODEL

SCALE

UNIT

XXXXXXXXXXXXXXXXXXXX

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

123456789

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design Department

123456789

B

C

D

E E

1

234

A

4-R2.0

B

K

C

50.0

D

XXXXXXXXX

MODEL

UNIT

SCALE

XXXXXXXXXXXXXXXXXXXX

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

123456789

Tanaka Shimano Ioka Oyama

DRAWING NO.

123456789 A4

Seiko I Infotech Inc. Design Department

1

234

A

4-R2.0

B

K

C

50.0

D

XXXXXXXXX

MODEL

UNIT

SCALE

XXXXXXXXXXXXXXXXXXXX

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

123456789

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design Department

123456789 A4

Chapter

1

Front End

A

B

C

D

Before Use Copy Function

Chapter

2

SHEET

PAGE

A4 long

Rear End

Chapter

4-R2.0

B

C

K

100.0

D

K

50.0

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

A

B

50.0

C

D

SHEET

PAGE

Chapter

5

A

B

50.0

C

D

SHEET

PAGE

Chapter

6

Copying after

performing mirror

reverse for the original

(& page 52 )

Copying/submitting

after performing white

on black reverse for the

original

(& page 45 )

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

UNIT

1/1

1

234

4-R2.0

CHECKED BY SIGNED BY DRAWN BY

1

4-R2.0

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789A4

234

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789A4

A

A

B

B

50.0

C

C

D

D

SHEET

PAGE

A

A

B

B

50.0

C

C

D

D

SCALE

1/1

APPROVED BY

SHEET

PAGE

SHEET

PAGE

1

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

50.0

4-R2.0

234

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

234

K

50.0

XXXXXXXXX

MODEL

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

XXXXXXXXXXXXXXXXXXXX

1

A

4-R2.0

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

A

B

50.0

C

D

SHEET

PAGE

LP-1030-MF User's Manual for Multifunction Printer Operation

17

Chapter

1

1

234

150dpi 300dpi 600dpi

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Copying after sorting

multiple originals

(& page 57 )

Copying/submitting

after adjusting the

original's sharpness

(& page 44 )

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

1

A

4-R2.0

B

C

D

1

A

4-R2.0

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

SCALE

1/1

234

234

1

K

4-R2.0

K

50.0

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

MODEL

DRAWING NO.

123456789A4

TITLE

PART NO.

DRAWING NO.

UNIT

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

A

234

B

50.0

C

50.0

D

K

50.0

XXXXXXXXX

SHEET

PAGE

XXXXXXXXXXXXXXXXXXXX

XXXXXXXXX

123456789

MODEL

123456789 A4

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

1

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

A

B

C

D

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

4-R2.0

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

234

1

1

A

4-R2.0

K

4-R2.0

B

50.0

C

XXXXXXXXX

MODEL

D

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

234

234

50.0

K

K

50.0

50.0

XXXXXXXXXXXXXXXXXXXX

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

XXXXXXXXX

PART NO.

123456789

MODEL

DRAWING NO.

123456789 A4

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

1

A

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

A

B

C

50.0

D

SHEET

PAGE

XXXXXXXXXXXXXXXXXXXX

4-R2.0

2

3

A

A

B

B

C

50.0

C

D

D

SHEET

PAGE

SHEET

PAGE

234

K

50.0

XXXXXXXXX

MODEL

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

XXXXXXXXXXXXXXXXXXXX

A

B

50.0

C

D

SHEET

PAGE

2

3

A

A

B

B

C

50.0

C

D

D

SHEET

PAGE

SHEET

PAGE

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Submitting after

selecting the scan

resolution

(& page 87 )

Submitting after

selecting the le format

of the scan data.

(& page 88 )

A

B

C

D

1

4-R2.0

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

234

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

1

A

4-R2.0

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

A

B

50.0

C

D

SHEET

PAGE

PDF TIFF

K

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

A

B

50.0

C

D

SHEET

PAGE

18

LP-1030-MF User's Manual for Multifunction Printer Operation

About Originals

This section describes the original sizes and thicknesses available with the Printer. It

also describes the scannable range.

Chapter

1

Before Use Copy Function

Scannable Original Conditions

Maximum width: 914.4 mm (36 inches)

Minimum width: 182 mm (7.17 inches)

Maximum length: 10000 mm (393.70 inches)

Minimum length: 210 mm (8.27 inches)

Thickness: 0.05 (0.002 inches) to 0.2 mm (0.008 inches)

Type: Non-transparent or semi-transparent originals

Other conditions:

- Originals with no folds, wrinkles, tears, or holes

-

When the original is rolled, the diameter must be at least 40 mm

(1.57

inches

)

- When the original is rolled, extend it to make the curl width

80 mm (3.14 inches) more, and the height 10 mm (0.39 inches)

or less as follows.

Original

80 mm (3.14 inches)

10 mm (0.39 inches)
or less

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Unscannable Originals

The following originals may cause paper jams, or they may be damaged.

- Originals non included in those described in Scannable Original Conditions

(& page 19 )

- Originals with staples or clips

- Originals with tears, ssures, or holes

- Originals with wrinkles, rips, or other defects

- Originals with curls or waves

- Originals with folds

- Originals with 2 or more sheets axed or overlapped together

- Originals with processed surfaces. For example, thermal paper, art paper, foil,

carbon paper, or conductive paper

LP-1030-MF User's Manual for Multifunction Printer Operation

Chapter

6

19

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

- Originals with protruding parts such as an index or label

- Originals that are thin and soft

- Originals that are bound (such as books)

- Originals that are wet or sticky

- Originals with partial thickness dierences

- Originals stuck with adhesive tape or glue

- Originals with a thick plate attached to the end

- Originals with undried ink or correction uid

- Originals with rear carbon attached

- Originals other than paper (such as electronic substrates, glass products, or

metal products)

Using Carrier Sheets with Originals

Note

Be sure to use a carrier sheet to protect important or glossy originals.

* Without the carrier sheet, the original may be damaged by a jam or similar

problem.

The tracks from the advance roller may mark the original.

Use a carrier sheet for the following original types.

- Originals with 2 or more sheets axed or overlapped together

- Originals with folds

- Originals with wrinkles, rips, or other defects

- Originals with curls or waves

- Originals with tears, ssures, or holes

- Originals with a trace of paper clip

- Originals with staples

- Originals stuck with adhesive tape or glue

- Originals not straight on the front end

- Originals such as photographs that stick easily to glass

- Originals such as pencil drawings that may make the scanner glass or other

parts dirty

Also, to scan a non-standard size as a standard size, use a carrier sheet.

20

LP-1030-MF User's Manual for Multifunction Printer Operation

Guaranteed Image Scan Range

Max: Up to 1219.2 mm

Max: Up to 914.4 mm

The Printer scans all the original except for 5 mm (0.20 inches) to the front and rear,

and 3 mm (0.12 inches) on both sides.

(36 inches)

Chapter

1

Before Use Copy Function

Chapter

2

3 mm

(0.12 inches)

Paper feed
direction

5 mm (0.20 inches)

(0.12 inches)

5 mm (0.20 inches)

Guaranteed image scan range

3 mm

(48 inches)

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

21

Chapter

TIP

Align the right original width guide for A series originals

1

Before Use Copy Function

Loading the Original

This section describes how to load the original.

Chapter

Loading the Original

2

Adjust the position of the original

1

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Align the right original width guide for originals with
size standards in mm

Chapter

Alignment area diers depending on the size standard as follows.

6

width guide.

Slide the right and left original width guides
so that they are aligned with the size line
appropriate for the original size.

Slide the guide so that the desired A
series size is shown in this window.

For the left original width guide:
Slide the guide so that the desired A
series size is shown in this window.

For the right original width guide:
Align the center bar's left edge with
the size line.

For the left original width guide:
Align the center bar's right edge with
the size line.

22

Center bar

Align the right original width guide for originals with size standards in inch,
and with 610 mm (24.02 inches) and 914 mm (35.98 inches)

For the right original width guide:
Align the center bar's left edge with
the size line.

For the left original width guide:
Align the center bar's right edge with
the size line.

LP-1030-MF User's Manual for Multifunction Printer Operation

Load the original.

TIP

2

Position the original facing down. Set it in the
Printer aligned with the original width guide.
The inserted original is automatically pulled
into the Printer, and set.

Chapter

1

Before Use Copy Function

Chapter

2

Position the original touching the front roller, and keep it slack. This

ensures the original is inserted straight.

When scanning a long original, roll the original in your hands, and then

set it. This makes it easier to scan the original straight.

Note

The Printer can output the original either to the front or the rear. When

outputting from the front, to prevent the original from being damaged,

keep the original width guide out of the way at both ends.

In this Printer, the original is set in the center. Even when the original is not

a standard size, set it in the middle.

When the Printer is set to output the original from the front, set the original

by aligning it with a size line.

When using a carrier sheet, do not set the Printer to output the original

from the front. The carrier may catch, resulting in damage to the original.

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

23

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Canceling Original Scanning

To cancel the scanning of the original partway, for example, if the original is fed at

an angle, or is ripped, perform the steps below.

Press STOP FEED.

1

When STOP FEED on the operation panel is
pressed, the scanning stops partway.

Open the scanner cover.

2

Chapter

5

Chapter

6

Lock the stopper by sliding it to the

3

Remove the original.

4

Stopper

right side.

Slide the stopper to the right.

Open the scanner cover, and remove the
original.

24

LP-1030-MF User's Manual for Multifunction Printer Operation

Release the stopper by sliding it to

5

the left side.

Slide the stopper to the left.

Chapter

1

Before Use Copy Function

Chapter

2

Close the scanner cover.

6

Then the Printer becomes ready.

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

25

Chapter

1

Before Use Copy Function

Regular Cleaning

Dirt from originals and other foreign matter may adhere to the original scanning

area. Clean this area regularly.

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Note

Never use volatile solvents such as thinner, benzene, or alcohol.

Cleaning the Shading Guide and Scanner Glass

Set the stopper before cleaning the original scanning area.

Wipe the shading guide and scanner glass with a dry cloth.

If they are significantly dirty, soak a soft cloth in water or a neutral detergent

diluted with water, wring the cloth thoroughly, and then wipe them.

Stopper

Scanner glass

Shading guide

Chapter

6

26

LP-1030-MF User's Manual for Multifunction Printer Operation

Chapter

2

Copy Functions

Chapter

1

Before Use Copy Function

This chapter describes the copy functions of the Printer.

Chapter Contents

Copy Operation Flow .............................................................................28

T

Copy Function Overview ......................................................................30

T

Selecting the Original Type ..................................................................31

T

Adjusting the Density ...........................................................................32

T

Selecting the Paper Position ................................................................ 33

T

Selecting the Original Size ...................................................................34

T

Selecting the Original Size Standard .................................................38

T

Selecting the Original Output Direction ...........................................39

T

Partial Copying .......................................................................................40

T

Adjusting the Background ...................................................................42

T

Adjusting the Original's Contrast ........................................................43

T

Adjusting the Original's Sharpness ................................................... 44

T

Performing White on Black Reverse ...................................................45

T

Setting the Scale ....................................................................................46

T

Adding Blank Space ...............................................................................47

T

Selecting the Paper Type ......................................................................48

T

Centering scan image ............................................................................49

T

Erasing the Frame ..................................................................................50

T

Selecting the Paper Output Slot .........................................................51

T

Performing Mirror Reverse ...................................................................52

T

Entering the Number of Copies ...........................................................53

T

Performing a Moderate Scan ...............................................................54

T

Copying an Original with Text & Lines ...............................................55

T

Copying a Blueprint Original ...............................................................56

T

Sorting ...................................................................................................... 57

T

Sorting Flow ............................................................................................58

T

Test Printing Sorted Originals..............................................................61

T

Additionally Copying the Sorted and Printed Originals ................62

T

Initializing the Setting ...........................................................................63

T

Handling copy jobs ................................................................................64

T

Additionally copying the Copied Originals .......................................65

T

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

27

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Copy Operation Flow

This section describes the basic operation ow for copying an original.

Press COPY

When authentication is necessary, enter a username and
password, or PIN code.
For more details, see Chapter 4 in the separate User's

Manual for Basic Printer Operation.

Copy's top screen

Chapter

5

Chapter

6

Select the Original Type

Select the image quality type of
the original. (& page 31 )

Adjust the Density

Adjust the copy density.

(& page 32 )

Select the Original Size

Select the size of the original.

(& page 34 )

With the default setting AUTO,
the Printer automatically
selects the paper size.

Select the Roll Position

From the paper types installed
in the Printer, select the paper
type for copying.

(& page 33 )

With the default setting AUTO,
the Printer automatically
selects the paper to be
printed on.

Press Original

Original Settings screen

Press Scale

28

LP-1030-MF User's Manual for Multifunction Printer Operation

Setting the Scale

Set to enlarge or reduce the
original's size. (& page 46 )

Adjust the Background

Adjust the background color
for originals with an uneven
density. (& page 42 )

Scaling screen

Press Image

Image Quality screen

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Enter the Number of

Copies

Enter the desired number of
copies.

Press Back

Chapter

5

Chapter

6

Load the original

Load the original into the Printer. (& page 22 )

Press START

When Start Scanning is set to Original Setting in the

System menu, copying and submission start automatically

even if START is not pressed.

For more details, see Chapter 3 in the separate User's

Manual for Basic Printer Operation.

LP-1030-MF User's Manual for Multifunction Printer Operation

29

Chapter

1

Before Use Copy Function

Copy Function Overview

The copy functions available with the Printer are as follows. The detailed setting

procedures are described from the next page.

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Function Description

Original Type Select an image quality type appropriate for the original.

Copy Density Adjust the copy density.

Paper Position

Original Size Specify the size of the original.

Original Size Standard Select the original size standard.

Original Output

Direction

Partial Copy Copy an original partially.

Background

Compensation

Contrast Adjust the contrast of the original.

Sharpness Adjust the sharpness of the original's contours.

White on Black Reverse Copy an original with its white and black reversed.

Scale Scale the size of the original.

Blank Space Set blank space to the front and rear of the original.

Paper Type

Centering

From the paper types installed in the Printer, select the paper

type for copying.

Set the output direction for the original.

Delete background colors.

From the paper types installed in the Printer, select the paper

type for copying.

Copy the image at the center of the paper width.

This function is eective at Synchro Scan with the roll paper

position specied.

30

Erase Frame Erase the area around the original before copying.

Output Slot Selection Select the output slot for the paper.

Mirror Reverse Perform mirror reverse for the original before copying.

Number of Copies Set the number of copies.

Moderate Scan

Original with text &

lines

Blueprint Original Set the image quality appropriate for the blueprint original.

Sort Sort multiple originals before copying.

LP-1030-MF User's Manual for Multifunction Printer Operation

Feed the original moderately on scanning to prevent the original

from being damaged.

Adjust the image quality appropriate for the originals with text

and lines.

Selecting the Original Type

Text & LinesText/PhotoPhoto Blueprint

TIP

Select an image quality type appropriate for the original. This setting improves the

image quality of the printout.

Text & Lines

Select for originals with mixed text and line art.

Text/Phot o

Select for originals with mixed text and photos.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Photo

Select for general photos.

Blueprint

Select for blueprint originals.

1

234

A

4-R2.0

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

For a blueprint original,

- Select Blueprint here; and

- Adjust the image quality parameters, as described in Copying a

Blueprint Original (& page 56 ).

K

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

A

B

50.0

C

D

SHEET

PAGE

Place Name (Japanese) Hawaii (USA, State of Hawaii)

Place Name (English) State of Hawaii

Capital Honolulu (State Capital)

Area 16634 square kilometers

Population 1211537 (2000)

Time Zone JST -19 hours

For example, noon on Sunday in Hawaii

is 7am on Monday in Japan

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

1

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

4-R2.0

234

50.0

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

Chapter

5

Chapter

A

B

C

D

SHEET

PAGE

6

LP-1030-MF User's Manual for Multifunction Printer Operation

31

Chapter

Original

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Adjusting the Density

Adjust the density when copying an original. Select the desired density, to suit the

density of the original.

Density can be adjusted in seven levels.

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

A

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

1

A

4-R2.0

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

Low Normal

1

234

4-R2.0

K

50.0

XXXXXXXXX

MODEL

TITLE

PART NO.

123456789

DRAWING NO.

123456789A4

XXXXXXXXXXXXXXXXXXXX

A

B

50.0

C

D

SHEET

PAGE

A

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

1

4-R2.0

CHECKED BY SIGNED BY DRAWN BY

234

K

MODEL

TITLE

PART NO.

DRAWING NO.

234

K

MODEL

TITLE

PART NO.

DRAWING NO.

50.0

XXXXXXXXX

123456789

123456789A4

50.0

XXXXXXXXX

123456789

123456789A4

XXXXXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

A

B

50.0

C

D

SHEET

PAGE

A

B

50.0

C

D

SHEET

PAGE

1

A

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

4-R2.0

High

234

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

12345678

9

DRAWING NO.

123456789A4

A

B

50.0

C

D

SHEET

PAGE

32

LP-1030-MF User's Manual for Multifunction Printer Operation

Selecting the Paper Position

From the paper types installed in the Printer, select the paper type for copying.

Roll 1

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Roll 2

When Auto is selected, The Printer automatically selects the printing paper suitable

for the original.

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

33

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Selecting the Original Size

Select the size of the original.

The following four settings are available for the original size.

Auto

With Auto selected, the Printer identies the original to be:

- A standard portrait or landscape size; or

- A non-standard size.

Note: In the submission mode, Auto cannot be selected.

Chapter

5

Chapter

6

Portrait

Select for standard size originals and vertically oriented.

Landscape

Select for standard size originals and horizontally oriented.

Synchro Scan

Select for non-standard size originals. When Syncro Scan is selected, the paper is

cut to the same length as the original, which is called as synchro cut.

Note

When the original size is set to Auto, the Adding Blank Spase (& page 47 ),

and Erasing the Frame (& page 50 ) settings are disabled.

When Selecting the Original Size Standard (& page 38 ) is set to User

Dened, all settings are handled as Synchro Scan, even when Portrait or

Landscape is set to On.

34

LP-1030-MF User's Manual for Multifunction Printer Operation

The paper sizes available for the Printer are as follows.

A Series Standard Size Originals

Original Longer Side Shorter Side Load Direction

Chapter

1

Before Use Copy Function

A0 1189 mm (46.81 inches) 841 mm ( 33.11 inches) Landscape

A1 841 mm (33.11 inches) 594.5 mm (23.41 inches)

A2 594.5 mm (23.41 inches) 420.5 mm (16.56 inches)

A3 420.5 mm (16.56 inches) 297.3 mm (11.70 inches)

A4 297.3 mm (11.70 inches) 210.3 mm (8.28 inches)

Landscape or

portrait

Landscape or

portrait

Landscape or

portrait

Landscape or

portrait

A Series Width Originals

Original Paper Width

A0 width 841 mm (33.11 inches)

A1 width 594.5 mm (23.41 inches)

A2 width 420.5 mm (16.56 inches)

A3 width 297.3 mm (11.70 inches)

A4 width 210.3 mm (8.28 inches)

Minimum Original

Length

210 mm (8.27 inches)

Maximum Original

Length

10000 mm

(393.70 inches)

ARCH Series Standard Size Originals

Original Longer Side Shorter Side Load Direction

E 1219.2 mm (48 inches) 914.4 mm (36 inches) Landscape

D 914.4 mm (36 inches) 609.6 mm (24 inches)

C 609.6 mm (24 inches) 457.2 mm (18 inches)

B 457.2 mm (18 inches) 304.8 mm (12 inches)

A 304.8 mm (12 inches) 228.6 mm (9 inches)

Landscape or

portrait

Landscape or

portrait

Landscape or

portrait

Landscape or

portrait

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

35

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

ARCH Series Width Originals

Original Paper Width

E width 914.4 mm (36 inches)

D width 609.6 mm (24 inches)

C width 457.2 mm (18 inches)

B width 304.8 mm (12 inches)

A width 228.6 mm (9 inches)

Minimum Original

Length

210 mm (8.27 inches)

Maximum Original

Length

10000 mm

(393.70 inches)

ANSI Series Standard Size Originals

Original Longer Side Shorter Side Load Direction

E 1117.6 mm (44 inches) 863.6 mm (34 inches) Landscape

D 863.6 mm (34 inches) 558.8 mm (22 inches)

C 558.8 mm (22 inches) 431.8 mm (17 inches)

B 431.8 mm (17 inches) 279.4 mm (11 inches)

A 279.4 mm (11 inches) 215.9 mm (8.5 inches)

Landscape or

portrait

Landscape or

portrait

Landscape or

portrait

Landscape or

portrait

Chapter

6

36

ANSI Series Width Originals

Original Paper Width

E width 863.6 mm (34 inches)

D width 558.8 mm (22 inches)

C width 431.8 mm (17 inches)

B width 279.4 mm (11 inches)

A width 215.9 mm (8.5 inches)

30×42 Series Standard Size Originals

Original Longer Side Shorter Side Load Direction

30×42 1066.8 mm (42 inches) 762.0 mm (30 inches) Landscape

15×21 533.4 mm (21 inches) 381.0 mm (15 inches)

LP-1030-MF User's Manual for Multifunction Printer Operation

Minimum Original

Length

210 mm (8.27 inches)

Maximum Original

Length

10000 mm

(393.70 inches)

Landscape or

portrait

30×42 Series Width Originals

Original Paper Width

30" 762.0 mm (30 inches) 210 mm (8.27 inches)

21" 533.4 mm (21 inches) 210 mm (8.27 inches)

15" 381.0 mm (15 inches) 210 mm (8.27 inches)

Minimum Original

Length

Maximum Original

Length

10000 mm

(393.70 inches)

10000 mm

(393.70 inches)

10000 mm

(393.70 inches)

MAP Series Standard Size Originals

Original Longer Side Shorter Side Load Direction

B1 1000.0 mm (39.37 inches) 700.0 mm (27.56 inches) Landscape

B2 700.0 mm (27.56 inches) 500.0 mm (39.37 inches)

Landscape or

portrait

MAP Series Width Originals

Original Paper Width

B1 width 700.0 mm (27.56 inches)

B2 width 500.0 mm (39.37 inches)

Minimum Original

Length

210 mm (8.27 inches)

Maximum Original

Length

10000 mm

(393.70 inches)

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

DIN Series Standard Size Originals

Original Longer Side Shorter Side Load Direction

B1 1000.0 mm (39.37 inches) 707.0 mm (27.83 inches) Landscape

B2 707.0 mm (27.83 inches) 500.0 mm (39.37 inches)

B3 500.0 mm (39.37 inches) 353.0 mm (13.90 inches)

Landscape or

portrait

Landscape or

portrait

DIN Series Width Originals

Original Paper Width

B1 width 707.0 mm (27.83 inches)

B2 width 500.0 mm (39.37 inches)

B3 width 353.0 mm (13.90 inches)

LP-1030-MF User's Manual for Multifunction Printer Operation

Minimum Original

Length

210 mm (8.27 inches)

Maximum Original

Length

10000 mm

(393.70 inches)

Chapter

6

37

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Selecting the Original Size Standard

Select the size standard applied to the original.

Note

This menu shows only size standards with Available Size Standards set to

On in the System menu. (For more details, see the separate User's Manual

for Basic Printer Operation.)

Make sure this setting matches the original to be loaded.

To load a user dened series original, specify the size at User Dened Size

in the System menu. (For more details, see the separate User's Manual for

Basic Printer Operation.)

With Original Size Setting set to Auto, the Printer automatically identies

the originals of several size standards.

However, the scan operation time is slightly longer, as the Printer prescans

the edge of the original to identify its width.

When you intend to print on the paper of only one size standard, you

are recommended to set Original Size Setting to that size standard. For

example, when you print only on A series paper, you are recommended

to set Original Size Setting to A Series, so that the scan operation time is

reduced.

38

LP-1030-MF User's Manual for Multifunction Printer Operation

Selecting the Original Output Direction

In this Printer, either front or rear output is available for the original. Select on this

screen the output direction for the original.

Note

Output from the front is limited to originals up to 1219.2 mm (48 inches) in

length.

The Printer can output the original either to the front or the rear. When

outputting from the front, to prevent the original from being damaged,

keep the original width guide out of the way at both ends.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

39

Chapter

Distance from original's front end

TIP

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Partial Copying

With this function, the Printer copies an original partially.

1

A

B

4-R2.0

C

D

E E

Paper feed
direction

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

234

K

100.0

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789

A

Partial copy start position

B

C

Partial copy

D

length

SHEET

PAGE

A4 long

B

4-R2.0

C

K

D

E E

100.0

K

50.0

B

C

D

Chapter

5

Chapter

6

You may need many test copies to check the optimal density and

image quality for an original. In such cases, this function is useful for

copying only a part of the original and checking the results. The larger

the original, the more useful is this function.

To simplify the test copy operation, you are recommended to decide a

setting range for the test copy and register it in the memory. Then you

can check the test copy only by loading the memory. (& page 100 )

Note

When this function is selected,

- The original size setting is disabled. The Printer scans the original,

synchronizing with the original size.

- The frame erase setting is disabled.

- The Printer outputs the original normally from the printer front side.

Note that the Printer outputs the original from the rear side only when

the distance specied below exceeds 1219.2mm (48 inches).

From: Original's front end

To: Partial copy's rear end

When the partial copy length is set to 0, the partial copy function is disabled,

and the Printer issues a normal copy print.

40

LP-1030-MF User's Manual for Multifunction Printer Operation

The Printer does not copy with the value specied as follows.

- The distance specied below is longer than the original length.

From: Original's front end

To: Partial copy start position

- The distance specied below is longer than the maximum scannable

original length.

From: Original's front end

To: Partial copy's rear end

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

41

Chapter

XXXXXXXXXXXXXXXXXXXX

A4

SHEET

PAGE

234

A

B

C

D

Original with Background Color

Original with Light Dirt

1

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Adjusting the Background

With this function, before copying an original with the defect below, its background

color is removed.

- High background density;

- Light smears; or

- Folds casting strong shadows

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Background compensation is adjusted in 13 levels. The higher the number, the

greater the deleted background color. The lower the number, the greater the

remaining background color.

1

234

A

4-R2.0

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

1

234

A

4-R2.0

A

B

K

B

C

C

D

D

MODEL

SCALE

UNIT

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design department

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

K

50.0

XXXXXXXXX

MODEL

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

1

4-R2.0

50.0

XXXXXXXXX

123456789

123456789 A4

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

XXXXXXXXXXXXXXXXXXXX

A

B

C

XXXXXXXXXXXXXXXXXXXX

D

50.0

50.0

A

B

C

D

SHEET

PAGE

13

A

234

B

1

234

C

4-R2.0

50.0

K

D

50.0

K

50.0

SHEET

PAGE

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

MODEL

DRAWING NO.

123456789 A4

SCALE

UNIT

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design department

A

B

C

D

SHEET

XXXXXXXXX

PAGE

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

1

50.0

SHEET

PAGE

1

234

A

4-R2.0

B

C

D

MODEL

SCALE

UNIT

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design department

1

A

4-R2.0

A

B

A

B

C

D

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

B

C

D

50.0

K

50.0

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

234

1

4-R2.0

A

K

50.0

B

C

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

D

DRAWING NO.

123456789 A4

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

A

B

C

D

SHEET

PAGE

13

A

234

B

1

50.0

C

4-R2.0

K

D

50.0

SHEET

XXXXXXXXX

PAGE

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

A

B

50.0

C

50.0

K

D

50.0

SHEET

PAGE

XXXXXXXXX

MODEL

TITLE

PART NO.

123456789

DRAWING NO.

123456789

42

Note

Note that the background setting changes if the original type is reselected

after adjusting the background compensation (& page 31 ).

LP-1030-MF User's Manual for Multifunction Printer Operation

Adjusting the Original's Contrast

234

The brightness of the original can be adjusted.

1

A

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

4-R2.0

234

K

MODEL

TITLE

PART NO.

DRAWING NO.

50.0

XXXXXXXXX

123456789

123456789 A4

XXXXXXXXXXXXXXXXXXXX

A

B

50.0

C

D

SHEET

PAGE

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

DarkMedium Light

1

234

A

4-R2.0

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

K

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

50.0

SHEET

PAGE

A

A

B

B

C

C

D

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

1

4-R2.0

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

234

50.0

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

A

B

C

D

SHEET

PAGE

1

A

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

Chapter

A

4-R2.0

K

50.0

XXXXXXXXX

MODEL

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

XXXXXXXXXXXXXXXXXXXX

B

50.0

C

D

SHEET

PAGE

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

43

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Adjusting the Original's Sharpness

The contours of the original can be sharpened or softened.

Note

Note that the original's sharpness setting changes if the original type is

reselected after adjusting the original sharpness (& page 31 ).

Chapter

5

Chapter

6

44

LP-1030-MF User's Manual for Multifunction Printer Operation

Performing White on Black Reverse

234

The white and black of the original can be reversed before copying.

1

A

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

CHECKED BY SIGNED BY DRAWN BY

234

4-R2.0

K

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

A

B

50.0

C

D

SHEET

PAGE

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

1

A

4-R2.0

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

Off On

234

50.0

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

SHEET

PART NO.

123456789

PAGE

DRAWING NO.

123456789 A4

1

A

A

4-R2.0

B

B

K

C

C

D

D

MODEL

SCALE

UNIT

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design Department

50.0

XXXXXXXXX

123456789

123456789 A4

XXXXXXXXXXXXXXXXXXXX

Chapter

A

B

50.0

C

D

SHEET

PAGE

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

45

Chapter

Original

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Setting the Scale

The original's size can be scaled before copying.

Fixed

Enables the easy selection of a ratio that scales to a size in the same standard as the

original.

Examp l es: A1gA0 (141%), A0gA1 (70%)

Proportional

Scales while keeping the same ratio between the vertical and horizontal

dimensions of the original.

Custom

Scales with separate ratios for the vertical and horizontal dimensions of the original.

Chapter

6

46

1

234

50.0

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

234

50.0

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

A

B

C

D

SHEET

PAGE

A

B

C

D

SHEET

PAGE

1

234

A

4-R2.0

B

50.0

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

K

50.0

XXXXXXXXX

MODEL

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

XXXXXXXXXXXXXXXXXXXX

C

D

Example:
Enlarge from A4 to A3

A

B

C

D

SHEET

PAGE

A

4-R2.0

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

Proportional

1

A

4-R2.0

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

113.5%

Example:
Enlarge to 113.5%

LP-1030-MF User's Manual for Multifunction Printer Operation

CustomFixed

1

234

A

4-R2.0

B

K

113.5%

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

130%

Example:
Enlarge vertical to 110%
and horizontal to 130%

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

A

B

50.0

C

110%

D

SHEET

PAGE

Adding Blank Space

Blank space can be added to the front and rear (front end and rear end) of the

original before copying.

Note

This setting is enabled only when the original size is set to Synchro Scan (&

page 34 ).

Non-standard size original

Paper feed
direction

1

234

A

4-R2.0

B

K

C

D

E E

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

100.0

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

A4 long

123456789

A

B

C

D

SHEET

PAGE

1

234

A

4-R2.0

B

K

C

D

E E

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

100.0

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

A4 long

123456789

A

B

C

D

SHEET

PAGE

Front end

Rear end

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

47

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Selecting the Paper Type

From the types of the paper installed in the Printer, select your intended paper

type for copying.

Chapter

5

Chapter

6

48

LP-1030-MF User's Manual for Multifunction Printer Operation

Centering scan image

The scan image can be printed at the center of the paper width.

Note

Centering is eective on the conditions below:

- Roll Position setting is not Auto.

- Original Size is set to Synchro Scan.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

49

Chapter

Original

234

234

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Erasing the Frame

The area around the original can be erased before copying, so that the original's

frame is erased.

Note that this function is available only for standard size originals.

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Note

This setting is enabled only when the original size is set to Portrait or

Landscape (& page 34 ).

A

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

A

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

1

4-R2.0

CHECKED BY SIGNED BY DRAWN BY

1

4-R2.0

CHECKED BY SIGNED BY DRAWN BY

K

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

K

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

XXXXXXXXX

XXXXXXXXXXXXXXXXXXXX

123456789

123456789 A4

A

B

50.0

C

D

SHEET

PAGE

A

B

50.0

C

D

SHEET

PAGE

50

LP-1030-MF User's Manual for Multifunction Printer Operation

Selecting the Paper Output Slot

Select the output slot for the paper.

Output Tray On

Outputs to the tray when the print size is A3 or less. Other sizes are output to the

paper outlet slot.

Output Tray O

By setting Output Tray to O, the Printer outputs all sizes to the paper outlet slot.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

51

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Performing Mirror Reverse

Mirror reverse can be performed for the original before copying.

1

A

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

234

4-R2.0

K

MODEL

TITLE

PART NO.

DRAWING NO.

50.0

XXXXXXXXX

123456789

123456789 A4

XXXXXXXXXXXXXXXXXXXX

A

B

50.0

C

D

SHEET

PAGE

Chapter

5

Chapter

6

O On

1

234

A

4-R2.0

B

C

D

SCALE

UNIT

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

K

50.0

XXXXXXXXX

MODEL

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

XXXXXXXXXXXXXXXXXXXX

50.0

SHEET

PAGE

1

A

A

B

B

C

C

D

D

234

A

4-R2.0

50.0

XXXXXXXXXXXXXXXXXXXX

SHEET

PAGE

B

K

C

50.0

D

XXXXXXXXX

MODEL

SCALE

UNIT

1/1

1/1

TITLE

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

PART NO.

123456789

Tanaka Shimano Ioka Oyama

DRAWING NO.

Seiko I Infotech Inc. Design department

123456789 A4

52

LP-1030-MF User's Manual for Multifunction Printer Operation

Entering the Number of Copies

Enter the number of copies.

Note

To enable the entry of the number of copies, congure the settings, and

then press the Back button to return to the Copy top screen.

Up to 999 copies are available for one operation. If a higher number is

entered, the setting is invalid.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

53

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Performing a Moderate Scan

When Moderate Scan is set to On, the Printer feeds the original moderately to

prevent the original from being damaged.

Note

Even with Moderate Scan set to On, the Printer may not be able to feed the

original moderately depending on the settings of the copy scale ratio and

submission resolution.

Chapter

5

Chapter

6

54

LP-1030-MF User's Manual for Multifunction Printer Operation

Copying an Original with Text & Lines

Check the following settings to make a clear copy of an original with text and lines.

Automatic binary threshold

This parameter activates or deactivates the binarization threshold automatic

setting.

Choices: O

On (default)

Normally, keep this parameter to On.

If the copy output is unclear with the parameter to On, set it to Off and enter a

threshold value.

Binary threshold

Set the threshold value for binarization.

Enter a numeric value between 0 and 255 (default: 120).

The higher the value, the higher the image density.

The lower the value, the lower the image density.

When the automatic binary threshold is set to On, the Printer generates

automatically a threshold value, which is displayed as a reference. Use this reference

to choose a value when you enter the threshold manually.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

LP-1030-MF User's Manual for Multifunction Printer Operation

Chapter

6

55

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Copying a Blueprint Original

Check the following settings to make clear copy of a blueprint original.

Automatic binary threshold

This parameter activates or deactivates the binarization threshold automatic

setting.

Choices: O

On (default)

Normally, keep this parameter to On.

If the copy output is unclear with the parameter to On, set it to Off and enter a

threshold value.

Binary threshold

Set the threshold value for binarization.

Enter a numeric value between 0 and 255 (default: 120).

The higher the value, the higher the image density.

The lower the value, the lower the image density.

When the automatic binary threshold is set to On, the Printer generates

automatically a threshold value, which is displayed as a reference. Use this reference

to choose a value when you enter the threshold manually.

Original density disparity

Set the density disparity of the original.

Choices: Large

Small

Large disparity

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

UNIT

1/1

1

234

4-R2.0

K

MODEL

TITLE

CHECKED BY SIGNED BY DRAWN BY

PART NO.

DRAWING NO.

50.0

XXXXXXXXX

123456789

123456789A4

XXXXXXXXXXXXXXXXXXXX

A

B

50.0

C

D

SHEET

PAGE

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

1

4-R2.0

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

234

50.0

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789A4

A

B

C

D

SHEET

PAGE

A

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BY SIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

1

4-R2.0

234

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789A4

Small disparity

A

B

50.0

C

D

SHEET

PAGE

A

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design department

1

4-R2.0

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

234

50.0

K

50.0

XXXXXXXXX

MODEL

XXXXXXXXXXXXXXXXXXXX

TITLE

PART NO.

123456789

DRAWING NO.

123456789A4

A

B

C

D

SHEET

PAGE

56

High density overall,
and characters and
lines are clear

High density overall,
but characters and
lines are not clear

LP-1030-MF User's Manual for Multifunction Printer Operation

Low density overall,
but characters and
lines are clear

Low density overall,
and characters and
lines are not clear

Sorting

1

234

1

TIP

TIP

Multiple originals can be stored temporarily in the Printer to perform collated copy

such as sort copy or stack copy.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

A

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BYSIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

1

A

4-R2.0

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

234

1

1

A

4-R2.0

K

4-R2.0

B

50.0

C

XXXXXXXXX

MODEL

D

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

CHECKED BYSIGNED BY DRAWN BY

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BYSIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

234

234

50.0

50.0

K

K

50.0

50.0

XXXXXXXXXXXXXXXXXXXX

XXXXXXXXX

SHEET

MODEL

PAGE

XXXXXXXXXXXXXXXXXXXX

TITLE

XXXXXXXXX

PART NO.

123456789

MODEL

DRAWING NO.

123456789 A4

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

A

B

C

D

XXXXXXXXXXXXXXXXXXXX

2

3

A

B

C

50.0

D

SHEET

PAGE

SHEET

PAGE

1

234

A

1

A

1

4-R2.0

B

C

D

UNIT

SCALE

1/1

1/1

APPROVED BY

CHECKED BYSIGNED BY DRAWN BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

B

C

D

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

A

4-R2.0

B

C

D

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

SCALE

1/1

APPROVED BY

Tanaka Shimano Ioka Oyama

Seiko I Infotech Inc. Design Department

K

50.0

MODEL

TITLE

PART NO.

DRAWING NO.

UNIT

1/1

CHECKED BY SIGNED BY DRAWN BY

4-R2.0

XXXXXXXXX

123456789

123456789 A4

A

B

C

D

234

50.0

50.0

K

K

50.0

50.0

XXXXXXXXXXXXXXXXXXXX

XXXXXXXXX

SHEET

MODEL

PAGE

XXXXXXXXXXXXXXXXXXXX

TITLE

XXXXXXXXX

PART NO.

123456789

MODEL

DRAWING NO.

123456789 A4

TITLE

PART NO.

123456789

DRAWING NO.

123456789 A4

A

B

C

50.0

D

XXXXXXXXXXXXXXXXXXXX

2

3

A

A

B

B

C

C

D

D

SHEET

PAGE

SHEET

PAGE

Up to 750 sheets of data can be stored with the digital sort function.

Note

Larger image sizes reduce the number of images that can be stored.

Example:

- With A4 image size, max. 750-sheet images are stored.

- With A0 image size, max. 100-sheet images are stored.

While printing a digitally sorted job, the digital sort function can scan

originals of the next digitally sorted job.

Up to four jobs can be scanned in advance.

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

After digital sorting, press Copy to return to the copy mode. Note that

the Printer returns to the copy mode only after the digitally sorted

job processing is completed. To return to the copy mode during the

processing, exit the digitally sorted job at the job screen.

LP-1030-MF User's Manual for Multifunction Printer Operation

57

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Sorting Flow

This section describes the basic operation ow for digital sorting.

Press COPY

When authentication is necessary, enter a username and
password, or PIN code.
For more details, see Chapter 4 in the separate User's

Manual for Basic Printer Operation.

Copy's top screen

Chapter

5

Chapter

6

Select the Original Type

Select the image quality type
of the original. (& page 31 )

Adjust the Density

Adjust the copy density.

(& page 32 )

Press Digital Sorting

Sort's top screen

Select the Roll Position

From the paper types
installed in the Printer, select
the paper type for copying.

(& page 33 )

With the default setting
AUTO, the Printer
automatically selects the
paper to be printed on.

Press Original

58

LP-1030-MF User's Manual for Multifunction Printer Operation

Select the Original Size

Select the size of the original.

(& page 34 )

With the default setting
AUTO, the Printer
automatically selects the
paper size.

Setting the Scale

Set to enlarge or reduce the
original's size. (& page 46 )

Original Settings screen

Press Scale

Scaling screen

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Adjust the Background

Adjust the background color
for originals with an uneven
density. (& page 42 )

Press Image

Image Quality screen

Chapter

5

Chapter

6

Press Back

LP-1030-MF User's Manual for Multifunction Printer Operation

59

Chapter

TIP

1

Before Use Copy Function

Load the original

Load the original into the Printer. (& page 22 )

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

The number of scanned
originals is displayed.

Press START

When Start Scanning is set to Original Setting in the

System menu, copying and submission start automatically

even if START is not pressed.

For more details, see Chapter 3 in the separate User's

Manual for Basic Printer Operation.

Each time the Cancel key is

Scan all originals

Sort's top screen

pressed at the Digital Sort

top screen, data is deleted

starting from the end of the

stored data.

Chapter

6

60

Press ENTER

Set

Enter the number of copies.

Sort

Specify the collation method.

Print order

Specify the print order.

LP-1030-MF User's Manual for Multifunction Printer Operation

Output order congured by the sorting
and printing order settings when
printing three copies of three originals.

Collate Print Order

Original 123, 123, 123 111, 222, 333

Reverse 321, 321, 321 333, 222, 111

Press Print

Test Printing Sorted Originals

You can test print the most recently scanned original of the originals stored using

the digital sort function.

This is useful for checking for scan warping and image quality.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Press ENTER.

If the Check button is pressed, one sheet only of the most recently scanned original

is printed.

To delete this original, press CANCEL.

To continue scanning, set the original.

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

61

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Additionally Copying the Sorted and Printed Originals

Originals printed using the digital sort function can be copied additionally without

scanning again.

Additional copies can be made for the job most recently digitally sorted and

printed only.

Note

The following actions disable additional copying.

- Returning to standard copy mode.

- Performing the next digital sorting.

If printing using the digital sort func tion is complete, the Add copies button

appears.

Chapter

5

Chapter

6

Press the Add copies button to display the Reprint screen. Congure the number of

copies, sorting, and print order, and then press the Print button.

62

LP-1030-MF User's Manual for Multifunction Printer Operation

Initializing the Setting

The Printer initializes the setting for the copy operation, and returns to the initial

status.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

63

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Handling copy jobs

To display the copy job screen, press Job on the Copy Top screen.

Chapter

5

Chapter

6

At the Copy Job screen, the job under processing can be cancelled by pressing the

× button.

To cancel the job under processing, press Yes .

64

LP-1030-MF User's Manual for Multifunction Printer Operation

Additionally copying the Copied Originals

Copied originals can be copied additionally without scanning again.

Additional copies can be made for the job last copied only.

Chapter

1

Before Use Copy Function

Note

The following actions disable additional copying.

- Print data was received after copy printing.

- The panel was switched to a mode other than the standard copy mode

screen.

If copying is complete, the Add copies button appears.

Press the Add copies button to display the Reprint screen. Congure the number of

copies, and then press the Print button.

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

LP-1030-MF User's Manual for Multifunction Printer Operation

Chapter

6

65

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

66

LP-1030-MF User's Manual for Multifunction Printer Operation

Chapter

1

Before Use Copy Function

Chapter

3

Submission Functions

This chapter describes the submission functions of the Printer.

Chapter Contents

Submission Functions Outline .............................................................68

T

Preparing the network and host computer ...................................... 70

T

Submission Operation Flow .................................................................72

T

Submission Function Overview ..........................................................84

T

Selecting Scan Color Mode ..................................................................85

T

Selecting Original Type .........................................................................86

T

Selecting Scan Resolution .................................................................... 87

T

Selecting the File Format for Images to be Scanned ......................88

T

Conguring the Filename for Images to be Scanned .....................90

T

Submission and Copy in One Operation ...........................................92

T

Print Copies .............................................................................................93

T

Print Quality ............................................................................................94

T

Handling Image Submission Jobs .......................................................95

T

Handling Printer Submission Jobs ......................................................96

T

Reprinting through Printer Submission ............................................97

T

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

67

Chapter

TIP

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Submission Functions Outline

The Printer has the following 4 submission functions.

Image submission function

With this function, the Printer submits images scanned with the Printer to:

- shared folders; and

- FTP servers

on the host computers connected to an IPv4/IPv6 network.

Up to 100 destinations can be registered.

Printer

Chapter

5

Chapter

6

If Web functions are used, registration in multiple languages is possible.

Submission job box function

With this function, image data scanned with the Printer are stored in the

submission job box of the Printer.

Up to 99 image files can be saved in the submission job box with a maximum

capacity of 80GB.

Images stored in the submission jpb box can be submitted to shared folders on host

computers using the thumbnail submission function or retrieved using the web function.

Submission box

68

LP-1030-MF User's Manual for Multifunction Printer Operation

Thumbnail submission function

A list of thumbnails is shown on the operation panel for image data stored in the

submission box. With this function, you can select image data from the list and

submit it to shared folders on host computers connected to an IPv4/IPv6 network.

In addition, image data stored in the submission box can be accessed from a web

browser using the web function.

Submission box

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Printer submission function

With this function, color image data scanned with the Printer are printed with

another printer.

Up to 5 submission destinations can be registered.

Printer

Note

To scan in color mode, the optional Color Scan Upgrade (LP-857) is required.

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

69

Chapter

1

Before Use Copy Function

Preparing the network and host computer

Before operating submission functions, check your printer's network connection

and the shared folder on the host computer.

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Checking the Printer's Network Connection

Check that the IP address, subnet mask, and gateway address of the Printer are set

correctly. For more details, see the Chapter 3 in the separate User's Manual for

Basic Printer Operation.

Creating a Shared Folder

On the host computer, create a shared folder to which you will send the image

data.

Note

Assign write permission to the shared folder.

You are recommended to install the host computer on the same LAN as the

Printer to:

- Minimize the Printer's operation time decrease caused by the scanned

data transmission delay; and

- Prevent the scanned data leakage.

70

LP-1030-MF User's Manual for Multifunction Printer Operation

Preparing a printer to receive submissions

The Printer supports submission to the printers with:

- Language supporting the HP RTL / PDF format

- Communication protocol supporting LPR/RAW

For more information about recommended printers, contact our ser vice

representative.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

71

Chapter

1

Before Use Copy Function

Submission Operation Flow

Make sure the preparations for operating the submission functions (& page 70 )

have been completed before performing these operations.

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Submitting images (SMB connection)

Select the destination.

Press the number of the job
you intend to add or edit, and
press Add/Edit.

Press SUBMIT

When authentication is necessary, enter a username and
password, or PIN code.
For more details, see Chapter 4 in the separate User's

Manual for Basic Printer Operation.

Submit's top screen

Press Add/Edit

The destination of the image
submission function can also be
handled as the destination for the
thumbnail submission function.

72

Add or Edit Image Destination screen (1/2)

Set up the destination.

Set the protocol to SMB and
set the shared folder of the
destination.

Press >>

LP-1030-MF User's Manual for Multifunction Printer Operation

Set the presets.

If frequently used settings
are set in the preset memory,
the presets can be called
automatically when the
submission destination is
selected.
For details of preset functions,
see & page 99 .

Save the settings.

If the Save button is pressed,
the settings are saved and
the connection to specied
shared folder is conrmed.
If the connection cannot
be conrmed, check the
settings.

Add or Edit Image Destination screen (2/2)

(1) Press Save (2) Press Back

Submit's top screen

The following actions can be performed
by using the Web functions.

Copy submission destinations

Import/export submission destinations
For more details, see Chapter 2 in the
separate User's Ma nual for Basi c Printer

Operation.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Select the destination.

Select the number of the
destination and press OK.
Then the Printer checks
the connection to the
destination selected. If the
Printer is unable to check
the connection successfully,
review the condition of the
computer for submission.

Specify the functions

for submission.

For the supported functions,
see the (& page 84 ).

Functions Setting screen

Press OK

To specify a le name, press

and enter the le name.
As default the le name is
automatically generated.

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

73

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Load the original

Load the original into the Printer. (& page 22 )

Press START

When Start Scanning is set to Original Setting in

the System menu, the Printer starts scanning the

original automatically without START pressed.

For more details, see Chapter 3 in the separate

User's Manual for Basic Printer Operation.

Chapter

5

Chapter

6

74

LP-1030-MF User's Manual for Multifunction Printer Operation

Submitting images (FTP connection)

Select the destination.

Press the number of the job
you intend to add or edit, and
press Add/Edit.

Press SUBMIT

When authentication is necessary, enter a username and
password, or PIN code.
For more details, see Chapter 4 in the separate User's

Manual for Basic Printer Operation.

Submit's top screen

Add or Edit Image Destination screen (1/2)

Press Add/Edit

The destination of the image
submission function can also be
handled as the destination for the
thumbnail submission function.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Set up the destination.

Set the protocol to FTP and
asset the FTP server of the
destination.
Set the shared path name
to the path of the folder to
receive the submission.

Press >>

LP-1030-MF User's Manual for Multifunction Printer Operation

75

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Set up the FTP

connection.

Specify the FTP connection
method and FTP ports.
Generally, the default FTP
port is acceptable.

Save the settings.

If the Save button is pressed,
the settings are saved and
the connection to specied
shared folder is conrmed.
If the connection cannot
be conrmed, check the
settings.

Select the destination.

Select the number of the
destination and press OK.
Then the Printer checks
the connection to the
destination selected. If the
Printer is unable to check
the connection successfully,
review the condition of the
computer for submission.

Add or Edit Image Destination screen (2/2)

(1) Press Save (2) Press Back

Submit's top screen

Press OK

Set the presets.

If frequently used settings
are set in the preset memory,
the presets can be called
automatically only with
the submission destination
selected.
For details of preset
functions, see & page 99 .

The following actions can be performed
by using the Web functions.

Copy submission destinations

Import/export submission destinations
For more details, see Chapter 2 in the
separate User's Ma nual for Basi c Printer

Operation.

76

Functions Setting screen

Specify the functions

for submission.

For the supported functions,
see the (& page 84 ).

LP-1030-MF User's Manual for Multifunction Printer Operation

To specify a le name, press

and enter the le name.
As default the le name is
automatically generated.

Load the original

Load the original into the Printer. (& page 22 )

Press START

When Start Scanning is set to Original Setting in

the System menu, the Printer starts scanning the

original automatically without START pressed.

For more details, see Chapter 3 in the separate

User's Manual for Basic Printer Operation.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

77

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Storing image data in the submission job box

Press SUBMIT

When authentication is necessary, enter a username and
password, or PIN code.
For more details, see Chapter 4 in the separate User's

Manual for Basic Printer Operation.

Submit's top screen

Chapter

5

Chapter

6

Specify the functions

for submission.

For the supported functions,
see the (& page 72 ).

Press Submission Job Box

Functions Setting screen

To specify a le name, press

and enter the le name.
As default the le name is
automatically generated.

78

LP-1030-MF User's Manual for Multifunction Printer Operation

Load the original

Load the original into the Printer. (& page 22 )

Press START

When Start Scanning is set to Original Setting in

the System menu, the Printer starts scanning the

original automatically without START pressed.

For more details, see Chapter 3 in the separate

User's Manual for Basic Printer Operation.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

79

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Submitting thumbnails

Press SUBMIT

When authentication is necessary, enter a username and
password, or PIN code.
For more details, see Chapter 4 in the separate User's

Manual for Basic Printer Operation.

Submit's top screen

Select the destination.

Press the number of the job
you intend to add or edit, and
press Add/Edit.

Press Add/Edit

Chapter

6

80

Add or Edit Image Destination screen

Set up the destination.

Create a shared folder at the
destination.
Press SAVE to save the shared
folder settings and to check
the connection to the created
shared folder.
If the Printer is unable to check
the connection successfully,
review the settings.

LP-1030-MF User's Manual for Multifunction Printer Operation

(1) Press Save

The destination of the
thumbnail submission
function can also be used as
the destination for the image
submission function.

The following actions can be performed
by using the Web functions.

Copy submission destinations

Import/export submission destinations
For more details, see Chapter 2 in the
separate User's Ma nual for Basi c Printer

Operation.

(2) Press Back

Two submission destination settings are available: SMB
connection and FTP connection.
For details, see & page 72 Submitting images (SMB

connection) and & page 75 Submitting images (FTP
connection).

Submit's top screen

Chapter

1

Before Use Copy Function

Chapter

2

Select the image data

to be submitted

Select the destination.

Select the number of the
destination and press OK.
Then the Printer checks
the connection to the
destination selected. If the
Printer is unable to check
the connection successfully,
review the condition of the
computer for submission.

Thumbnail submission screen

Press NEXT

Press Submit from Thumbnail

Press Delete to delete the
selected images.
Press Detailed Information to
view detailed information
about selected images or
prohibit automatic deletion.
For details, see Chapter 3,

Job Box Retention Period in

the separate User’s Manual

for Basic Printer Operation.

Press OK

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

The thumbnail submission
screen is displayed and the
selected image is sent.
Wait until the transmission is
complete to perform the next
submission.

Thumbnail submission

LP-1030-MF User's Manual for Multifunction Printer Operation

81

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Submitting to a printer

Press SUBMIT

When authentication is necessary, enter a username and
password, or PIN code.
For more details, see Chapter 4 in the separate User's

Manual for Basic Printer Operation.

Submit's top screen

Press Submit Print Job

Chapter

5

Chapter

6

Select the destination.

Press the number of the job
you intend to add or edit, and
press Add/Edit.

Set up the destination.

Specify the destination
printer.
Press Save to save the settings
and to check the connection
to the specied printer.
If the Printer is unable to check
the connection successfully,
review the settings.

Add or Edit Image Destination screen

(1) Press Save

Press Add/Edit

The following actions can be performed
by using the Web functions.

Copy submission destinations

Import/export submission destinations
For more details, see Chapter 2 in the
separate User's Ma nual for Basi c Printer

Operation.

(2) Press Back

82

LP-1030-MF User's Manual for Multifunction Printer Operation

Select the destination.

Select the number of the
destination and press OK.
Then the Printer checks the
connection to the destination
selected. If the connection
cannot be checked, review
the condition of the printer
for submission.

Submit's top screen

Functions Setting screen

Press OK

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Specify the functions

for submission.

For the supported functions,
see the (& page 84 ).

Load the original

Load the original into the Printer. (& page 22 )

Press START

When Start Scanning is set to Original Setting in

the System menu, the Printer starts scanning the

original automatically without START pressed.

For more details, see Chapter 3 in the separate

User's Manual for Basic Printer Operation.

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

83

Chapter

1

Before Use Copy Function

Submission Function Overview

The submission functions available with the Printer are listed below. For details of

the procedure to set the functions starred, see the Chapter 2 Copy Functions.

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

Function Description

Original Size

Original Type

Background

Compensation

Density

Mirror Reverse

Original Size Standard

Original Output

Sharpness

Contrast

White on Black Reverse

Resolution Select the scan resolution. (& page 87 )

Moderate Scan

Original with text & lines

Specify the size of the original. (& page 34 )

Select an image quality type appropriate for the original.

(& page 86 )

Delete background colors. (& page 42 )

Adjust the scan density. (& page 32 )

Reverse the original and then scan. (& page 52 )

Select the size standard of the original. (& page 38 )

Set the original output location. (& page 51 )

Adjust the original's contour sharpness. (& page 44 )

Adjust the original contrast. (& page 43 )

Reverse the white and black of the original before scanning.

(& page 45 )

Feed the original moderately to prevent the original from

being damaged. (& page 54 )

Adjust the image quality appropriate for the originals with text

and lines. (& page 55 )

84

Blueprint Original

Color Mode Select a scan color mode. (& page 85 )

File Format Select a image le format. (& page 88 )

File Name Setting Create a le name for the scan image data. (& page 90 )

Print Copies

Printer Quality Set the print quality (for printer submission). (& page 94 )

Copy

LP-1030-MF User's Manual for Multifunction Printer Operation

Set the image quality appropriate for the blueprint original.

(& page 56 )

Set the number of copies to print (for printer submission).

(& page 93 )

Perform both submission and copy with a single scan.

(& page 92 )

Selecting Scan Color Mode

Select a scan color mode from monochrome, grayscale, and color.

Monochrome

The scanner scans in monochrome binary format.

Grayscale

The scanner scans in monochrome multi-bit format.

Chapter

1

Before Use Copy Function

Chapter

2

Color

The scanner scans in color mode.

Note

To scan in color mode, the optional Color Scan Upgrade (LP-857) is required.

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

85

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Selecting Original Type

Set the original type for each color mode (monochrome/grayscale/color).

Monochrome

Text & Lines

Select for originals with mixed text and line art.

Text/Phot o

Select for originals with mixed text and photos.

Photo

Select for general photos.

Blueprint

Select for blueprint originals.

Grayscale

The original type setting is not required.

Chapter

5

Chapter

6

Color

Text

Select for scanning texts mainly.

Text/Phot o

Select for scanning texts mainly.

Photo

Select for scanning photos.

Map

Select for scanning maps.

86

LP-1030-MF User's Manual for Multifunction Printer Operation

Selecting Scan Resolution

Select the scan resolution from the options below.

150 dpi

The scanner scans at 150 dpi.

200 dpi

The scanner scans at 200 dpi.

Chapter

1

Before Use Copy Function

Chapter

2

300 dpi

The scanner scans at 300 dpi.

400 dpi

The scanner scans at 400 dpi.

600 dpi

The scanner scans at 600 dpi.

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

87

Chapter

TIP

1

Before Use Copy Function

Chapter

2

Selecting the File Format for Images to be Scanned

Select the le format for image les to be created.

PDF le

Creates a scan image in the PDF le.

Multi-page PDF le

Creates a scan image in the multi-page PDF le.

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

TIFF le

Creates a scan image in the TIFF le.

Multi-page TIFF le

Creates a scan image in the multi-page TIFF le.

JPEG le

Creates a scan image in the JPEG le.

The supported le formats dier depending on the scan color mode.

File format

PDF Yes No Yes

Multi-page PDF Yes No Yes

TIFF Yes Yes Yes

Multi-page TIFF Ye s No Yes

JPEG No No Yes

Multi-page PDF and Multi-page TIFF create a single PDF le or

single TIFF le from multiple-page original, with Enter pressed after

completing scanning.

Monochrome Grayscale Color

Scan color mode

88

LP-1030-MF User's Manual for Multifunction Printer Operation

Note

TIP

Press Cancel to cancel the latest scan image, e.g., whose original was

scanned obliquely.

One le contains 99 pages at maximum.

If the hard disk capacity is exceeded, no more image can be scanned.

During the multi-page scan, scan color mode, le format, and le name

cannot be changed.

With JPEG selected, the maximum scan length depends on the setting of

the resolution as follows.

150dpi: 11096mm (436.85 inches), 200dpi: 8322mm (327.64 inches),

300dpi: 5548mm (218.42 inches), 400dpi: 4161mm (163.82 inches),

600dpi: 2774mm ( 109.21 inches)

The scannable original length changes depending on the color mode,

le format, resolution, and original width. For details to scan lengthy

documents, contact your dealer or the nearest service representative.

During multi-page scan, the scannable number of pages changes

depending on the le format, resolution, original width, and original

length. For details about multipage scan, contact your dealer or the

nearest service representative.

The image size that can be displayed on a PC changes depending on

the operating system, the application software, and the memory of the

PC and the hard drive.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

LP-1030-MF User's Manual for Multifunction Printer Operation

Chapter

6

89

Chapter

TIP

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Conguring the Filename for Images to be Scanned

Set the name for les to be created. By default, the Printer automatically generates

a lename by appending the scan date and time (year, month, day, hours, minutes,

and seconds of scanning) to the basic lename for image data submission.

Example:

Basic lename for image data submission: scan_

Scan date and time: 12:34:56 of on September 30, 2010

The Printer automatically generates the File name as:

scan_100930123456.pdf

An extension is added to the le name depending on the le format setting:

-PDF: .pdf

-TIFF: .tif

-JPEG: .jpg

To congure a lename of your choosing, congure the following settings.

Chapter

5

Chapter

6

Press the abc button and congure the settings at the screen shown below.

90

LP-1030-MF User's Manual for Multifunction Printer Operation

Filename

TIP

TIP

Specify a lename of your choosing. The permitted length range for lenames is 1

to 60 characters.

Chapter

1

Before Use Copy Function

Overwrite if lename exists

Specify whether to overwrite if a le with the same lename is in the submission

destination folder.

Date and time

The year, month, day, hours, minutes, and seconds of scanning is appended to the

lename you chose.

Serial number

A serial number is appended to the lename you chose.

The serial number can be congured from 001 through 999.

When the sequential number reaches 999, the next number is 001.

None

Filename of your choosing only.

Start number

When the le naming setting is Sequential number, set the start number for the

sequential number.

The sequential number setting adds three digits automatically.

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

The sequential number 1 becomes 001.

Reset

Return the start number for the Sequential number setting to 1.

LP-1030-MF User's Manual for Multifunction Printer Operation

91

Chapter

TIP

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Submission and Copy in One Operation

With a single scan, you can create an image le and then print a copy of that image

in only one operation.

Press Paper in the Image Submission or Submission Box Top screen.

Chapter

5

Chapter

6

Configure Print Copies, Output Tray (& page 51 ), and Paper Type (& page

48 ), and then press Back.

When you do not need to select the output tray and the paper type,

press the Copy button in the Image Submission or Submission Box Top

screen and enter only the number of copies.

Note

When you continuously perform scanning operations, note that the Printer

cannot scan again until the previous job printing is complete.

If an error, such as lack of paper or paper jam, occurs during copy, switch to

the copy function and check the error screen.

92

LP-1030-MF User's Manual for Multifunction Printer Operation

Print Copies

Set the number of copies to print before the printer submission.

The value can be set from 1 to 999 copies. (The default setting is 1.)

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

93

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Print Quality

Set the print quality before the printer submission. The following settings are

available.

- High Quality

- Standard (default setting)

- High Speed

Chapter

5

Chapter

6

94

LP-1030-MF User's Manual for Multifunction Printer Operation

Handling Image Submission Jobs

To display the Image Submission Job screen, press Job on the Image Submission

Top screen.

Jobs being processed can be stopped on the Image Submission Job screen.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

At the Submission Job screen, the job under processing can be cancelled by

pressing the × button.

To cancel the job under processing, press Yes .

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

95

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Handling Printer Submission Jobs

To display the Printer Submission Job screen, press Job on the Printer Submission

Top screen.

The following operations can be performed on the Printer Submission Job screen.

- Stop jobs being processed

- Delete processed jobs

- Reprint (resubmit) the specied number of copies of processed jobs

At the Printer Submission Job screen, the job under processing can be cancelled.

Chapter

5

Chapter

6

At the Printer Job screen, the job under processing can be cancelled by pressing

the × button.

To cancel the job under processing, press Yes .

96

LP-1030-MF User's Manual for Multifunction Printer Operation

Reprinting through Printer Submission

When you want to print additional copies of originals printed using printer

submission, you can print additional copies without scanning again.

Additional prints can be made for the most recently scanned job only.

When printing a large number of copies, you are recommended to use this function

after checking for scan warping and image quality, which can prevent large-scale

print mistakes.

After ending printer submission, press the Job button.

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Press the Reprint button.

Enter the number of copies to be printed, and then press Print.

Chapter

5

Chapter

6

LP-1030-MF User's Manual for Multifunction Printer Operation

97

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

Chapter

6

98

LP-1030-MF User's Manual for Multifunction Printer Operation

Chapter

1

Before Use Copy Function

Chapter

4

Preset Functions

This chapter describes the Printer's preset functions.

Chapter Contents

Presets Overview....................................................................................86

T

Creating a preset in the Memory ........................................................87

T

Calling a Preset from the Memory ......................................................88

T

Saving Settings as Default Settings ...................................................89

T

Changing a Preset Name ......................................................................90

T

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Chapter

5

LP-1030-MF User's Manual for Multifunction Printer Operation

Chapter

6

99

Chapter

1

Before Use Copy Function

Chapter

2

Chapter

3

Submission

Function

Chapter

4

Preset Functions Scan Function Troubleshooting

Presets Overview

The Printer must be given a description of the requirements of each copy and

submission operation. You can save this description and call it when required. This

description is called a preset.

You are recommended to save frequently used settings or complicated settings as

presets, so that you do not have to enter the setting items or values.

When the settings for each submission destination are xed, presets can be created

in the memory for each submission destination.

With this function, presets can be called automatically by selecting a submission

destination.

Chapter

5

Chapter

6

100

LP-1030-MF User's Manual for Multifunction Printer Operation