Oki B8300n, B83MP, B83LT, B83TT, B83D Installation Manual
...
Start of installation
End
B83MP /
Power Suply Unit
... (P. 2)
B83LT /
Power Suply Unit
..... (P. 3)
B83TT /
Power Suply Unit
.... (P. 4)
Main unit
.................................. (P. 5)
B83MP / B83LT / B83TT /
B83D / B83DB.................(P. 14 & 15)
B83D ....................(P. 7)
B83DB ................(P. 8)
B83MB/Power Suply Unit
...
(P. 9)
B83F/Power Suply Unit
.......
(P. 10)
B83SS
....................................
(P. 11)
B83THP / USP / FHP / FBP.(P. 12)
Main unit
Main unit
Finishing device
Finishing device
Duplex/bypass device
Finishing device
Paper feeding deviceDuplex device Paper feeding device
Installation Manual for B8300
and Its Peripheral Devices
Duplex/bypass
device installed?
No
No
Finishing device
installed?
Hard
Disk
2
Yes
Yes
1: When installing a paper feeding device, an optional power supply unit or a duplex/bypass device, be
sure to reattach the rear cabinet, the AC inlet cover, and the harness cover of the main unit at the end
of installation as needed.
2: When installing electrical devices, be sure to install them one at a time.
3: Only off center adjustment is needed for B83D.
To install the devices efficiently, follow the procedure below.
Some peripheral devices may have been installed as
standard devies depending on the main unit model.
Part of descriptions and illustrations may be different.
2)
Paper guide position adjustment/off center adjustment
1) Installation of driver software, setting,
and operation check
Main unit / B83H..............
(P. 13)
[Electrical setting/adjustment]
Main unit, paper feeding
device, and power supply
unit.
Install duplex/pypass device.
Install finishing device.
1
<2> Connect the connector of the relay harness of the
multi purpose drawer to CN10 (blue connector) of the
PCU PWB of the main unit of the printer.
For installation of a finisher or a mail-bin stacker,
see its installation manual.
7. Carry out the off center adjustment.
CN10
Rear guide
Paper guide
B83MP Installation Manual
<Before installation>
FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS.
SEE OKI DIGITAL PRINTE R SERV ICE MA NUAL O R
INSTALLATION MANUAL TO DETERMINE SUITABILITY.
When installing a finisher or a mail-bin stacker with
B83MP, a power supply unit is needed.
<Parts included>
Front mounting plates:
2 pcs.
Rear mounting plates:
2 pcs.
Screws (M4x8):
4 pcs.
1. Turn off the main switch of the main unit
of the printer.
Turn the main sw itch located on th e
front side of the main unit to the "OFF"
position.
Then, remove th e power plug of th e
main unit from the outlet.
"OFF"
2. Put the main unit of the printer on the
multi purpose drawer.
<1> Pull out the paper tray of the main unit until it stops
and then remove it by lifting both ends of the tray.
<2> Hold the main unit of the printer at the positions
shown in the illustration and put the main unit on the multi
purpose drawer so that the front side and the left side of
the main unit are aligned to those of the multi purpose
drawer.
Front side
Rear side
[Caution]
For installation of the main unit, it
must be held by two persons and
installed carefully.
<1>Attach the two rear mounting plates using a supplied
screw for each.
3. Connect the main unit of the printer to the
multi purpose drawer.
Rear mounting plate
Rear mounting plate
Screw
Screw
[Caution]
Insert th e m ounting plate
under the tray frame.
Tray frame
Mounting
plate
<2> Pull out the multi purpose drawer until it stops and
attach the two front mounting plates using a supplied
screw for each.
Then, remove the lock of the paper tray and close the
tray.
Screw
Screw
Front mounting plate
Front mounting plate
<3> Reattac h the paper tr ay of the main unit of the
printer.
<1> Remove the screw that fixes the harness cover of the
main unit of the printer and then slide the harness cover
up to remove it.
Harness cover
Screw
4. Connect the harness to the main unit of
the printer.
Cut out.
* Cut out the harness cover as shown in the illustration.
Connector
5. Attach the harness cover.
Reattach the harness cover to its original position and fix it
with the removed screw.
Wire saddle
Harness cover
Screw
* Fix the harness securely to the wire saddle.
Wire saddle
6. Adjust the position of the paper guides of
the paper tray.
<1> To use the setting mode, insert the power plug of the
main unit of the printer to the outlet and turn the main
switch on while pressing the [MENU] key and the [OK] key
of the operation panel of the main unit of the printer.
<2> Press the [MENU] key several times to display "SIZE
ADJUSTMENT A" and press the [OK] key.
<3> "MAXIMUM SIZE" is displayed.
Pull out the paper tray and extend the paper guides to the
maximum. Then, return the paper tray into the main unit
and press the [OK] key.
<4> "MINIMUM SIZE" is displayed.
Pull out the paper tray again and narrow the paper guides
to the minimum. Then, return the paper tray into the main
unit and press the [OK] key.
<5> Press the [BAC K/ CLEAR] key to exit the settin g
mode.
[Caution]
If the setting above is not carried out, the paper detection
function will not operate.
Installation is now complete.
* If another peripheral device must be installed,
carry out the following step at the end of the
installation work.
2
B83LT Installation Manual
<Parts included>
1. Turn off the main switch of the main unit of the printer.
2. Attach the adjusters and adjust them.
3. Put the main unit of the printer on the stand/paper drawer.
<1> Pull out the paper tray of
the main unit until it stops and
then remove it by lifting both
ends of the tray.
Turn the main switch located on the front side of
the printer to the "OFF" position.
Then remove the power plug from the outlet.
7. Connect the power supply unit harness to the PCU PWB
of the main unit of the printer.
8. Connect the relay harness of the stand/paper drawer to
the power supply unit.
<1> Pass the cord of the power supply
unit through the hole of the rear cabinet
and attach t he re ar ca binet to the
stand/paper drawer.
9. Attach the rear cabinet of the stand/paper drawer.
Connect the AC cord of th e
power supply unit to the inlet
connector of the main unit of
the printer at the l ocation
shown in the illustration.
10. Connect the AC cord of the power supply unit to the
main unit of the printer.
<1> To use the setting mode, insert the power plug of the main unit of the
printer to the outlet and turn the main switch on while pressing the [MENU]
key and the [OK] key of the operation panel of the main unit of the printer.
<2> Press the [MENU] key several times to display "SIZE ADJUSTMENT
A" and press the [OK] key.
<3> "MAXIMUM SIZE" is displayed.
Pull out the paper tray and extend the paper guides to the maximum.
Then, return the paper tray into the unit and press the [OK] key.
<4> "MINIM UM SIZE" is
displayed. Pull out the paper
tray again a nd narrow the
paper guides to the minimum.
Then, return the paper tray into
the unit and press the [OK] key.
(The rear guide ne ed not be
adjusted.)
[Caution] If the setting above
is not car ried out, the pap er
detecti on functi on will not
operate.
12. Adjust the position of the paper guides of the upper
paper tray of the stand/paper drawer.
Remove t he four screw s for
packi ng. (See the ri ght
illustration.)
Insert the left paper guides and
right p aper guides to the front
and rear guide sl ots for the
paper size to be used. (See the
illustration below.)
(For the AB s ystem, set the
guides to A4. For the inch
system, set the guides to LT.)
11. Attach the paper guides to the lower tray.
"OFF"
<2> Hold the main unit of the
printer at the positions shown
in the illustration and put the main unit on the
stand/paper drawer so that the front side and the
left side of the main unit are aligned to those of
the stand/paper drawer.
Front side
Rear side
<1> Remove the screw t hat
fixes the harness cover of the
main unit of the p rinter and
slide the harness cover up to
remove it.
Cut out the harness cover as
shown in the illustration.
<3> Reatta ch the ha rness
cover t o its ori ginal position
and f ix it with th e removed
screw.
At this time, e nsure that the
optional power supply harness
are arranged as shown in the
illustration.
<2> Con nect the op tional
powe r supp ly har ness
connec tor to CN11 (red
connector) of the PCU PWB of
the main unit of the printer.
Connector
Wire saddle
Harness cover
Harness cover
Optional power
supply harness
Screw
Cut out.
Screw
Left adjuster: 1 pc.
Front mounting
plates: 2 pcs.
Rear mounting
plates: 2 pcs.
Adjuster covers: 4 pcs.
Screws (M4x8):
4 pcs.
Left paper guides: 2 pcs. Right paper guides: 2 pcs.
AC cord
Installation is now complete.
1
2
2
2
2
3
3
3
3
Screw
AC inlet cover
<2> Attach the AC inlet cover
to the rear cabinet of the
stand/paper drawer and fix it
with the removed screw.
Connect the relay h arness of
the stand/paper drawer to the
connector of the power supply
unit.
Connector of the power supply connector
Relay harness of the
stand/paper drawer
4. Connect the main unit to the stand/paper drawer.
6. Attach the power supply unit.
5. Remove the rear cabinet of the stand/paper drawer and
remove the AC inlet cover.
AC inlet cover
Cut out.
Power supply unit
Screws
Screws
<1> Remove the four screws that
fix t he rear cabinet and then
remove the rear cabinet.
Rear mounting plate
Rear mounting plate
Screw
Screw
Screw
Screw
Front
mounting plate
Front mounting plate
Rear cabinet
<3> Reattach the paper tray
of the main unit.
Paper guide
• Fix the harness securely to
the wire saddle.
Right paper guides
Left paper guides
Rear cabinet
FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS.
SEE OKI DIGITAL PRI NTER SERVICE MANUAL OR
INSTALLATION MANUAL TO DETERMINE SUITABILITY.
CN11
<1> Insert the left adjusters to
the stand/paper drawer.
<2> Turn ea ch adjuster to
lower it until it touches the f loor.
<3> Attach the four a djuster
covers.
Be sure t o attach th e left
adjuster to prevent overturning.
[Cautio n] The lower tray
cannot be pulled out unless
the adjuster is lowered to the
specified position.
[Caution]
For installation of the main unit, it must be
held by two persons and installed carefully.
<1>Att ach the two re ar
mounti ng plates using a
supplied screw for each.
Stand frame
Rear
mounting plate
[Caution]
Insert the rear m ounting
plates under the Stand frame.
<2>Pull out the upper tray
of the stand/p aper drawer
until it stops, and attach the
two fron t mounting plates
using a supplied screw for
each.
Then, remov e the lock of
the paper tray and close the
tray.
<2> Remove the screw that fixes the
AC inlet cover and then remove the
AC inlet cover.
<3> Cut out the AC inlet cover as
shown in the illustration.
Attach the power supply unit to the brackets and secure it using the three
supplied screws.
Bracket
Bracket
* If another peripheral device must be installed, carry out
the following step at the end of the installation work.
Paper guides
Rear guide
13. Carry out the off center adjustment.
Wire saddle
<Before installation>
• Start installation after checking that the DATA and
COMMUNICATION indicators on the operation panel are
neither lit nor blinking.
• For installation, a power supply unit is needed.
3
B83TT Installation Manual
<Parts included>
1. Turn off the main switch of the main unit of the printer.
2. Attach the adjusters and adjust them.
3. Put the main unit of the printer on the stand/paper drawer.
<1> Pull out the paper tray of
the main unit until it stops and
then remove it by lifting both
ends of the tray.
<1> Insert the left adjusters to
the stand/paper drawer.
<2> Turn the five adjusters to
lower them until they touch the
floor.
<3> Attach the fou r adjuster
covers.
• Be sure to attach the left
adju ster to prev ent
overturning.
[Caution] The lower tray
cannot be pulled out unless
the adjuster is lowe red to
the specified position.
Turn the main switch located on the front side of the
printer to the "OFF" position.
Then remove the power plug from the outlet.
Attach the two rear mounting
plates using a sup plied
screw for each.
4. Connect the main unit to the stand/paper drawer.
6. Attach the power supply unit.
7. Connect the power supply unit harness to the PCU PWB
of the main unit of the printer.
8. Connect the relay harness of the stand/paper drawer
to the power supply unit.
<1> Pass the cord of the power supply
unit through the hole of the rear cabinet
and attach t he re ar ca binet to the
stand/paper drawer.
9. Attach the rear cabinet of the stand/paper drawer.
Connect the AC cord of th e
power supply unit to the inlet
connector of the main unit of
the printer at the l ocation
shown in the illustration.
10. Connect the AC cord of the power supply unit to the
main unit of the printer.
<1> To use the setting mode, insert the power plug of the main unit of the
printer to the outlet and turn the main switch on while pressing the [MENU]
key and the [OK] key of the operation panel of the main unit of the printer.
<2> After pressing the [MENU] key several t imes to disp lay "SIZE
ADJUSTMENT A" in the message display and press the [OK] key.
<3> "MAXIMUM SIZE" is displayed.
Pull out the paper tray and extend the paper guides to the maximum.
Then, return the paper tray into the unit and press the [OK] key.
<4> "MINIM UM SIZE" is
displayed. Pull out the paper
tray again a nd narrow the
paper guides to the minimum.
Then, return the paper tray into
the unit and press the [OK] key.
(The rear guide ne ed not be
adjusted.)
[Caution]
If the se tting above is not
carried out, the paper detection
function will not operate.
11. Adjust the position of the paper guides of the
upper paper tray of the stand/paper drawer.
"OFF"
<2> Hold the main unit of the
printer at the positions shown
in the illustration and put the main unit on the
stand/paper drawer so that the front side and
the left side of the main unit are aligned to
those of the stand/paper drawer.
Front side
Rear side
<2> Remove the screw that fixes
the AC inlet cover and then remove
the AC inlet cover.
<3> Cut out the AC inlet cover as
shown in the illustration.
5. Remove the rear cabinet of the stand/paper drawer and
remove the AC inlet cover.
AC inlet cover
Cut out.
Power supply unit
Screws
Screws
<1> Remove the screw th at
fixes the harness cover of the
main unit of the pr inter and
slide the harness cover up to
remove it.
<3> Reat tach the har ness
cover to its original position and
fix it with the removed screw.
At this t ime, ensure that the
optional powe r sup ply unit
harness is arranged as shown
in the illustration.
Connector
Wire saddle
Harness cover
Harness cover
Optional power
supply harness
Screw
Cut out.
Screw
Left adjuster: 1 pc.
Front mounting
plates: 2 pcs.
Rear mounting
plates: 2 pcs.
Adjuster covers: 4 pcs.
Screws (M4x8):
4 pcs.
<1> Remove the four screws that
fix t he rear cabinet and then
remove the rear cabinet.
<2>Pull out the upper tray of
the stand/paper drawer until
it stops, and attach the two
front mounting plates using
a supplied screw for each.
Then, remove the lock of the
paper tray and close the
tray.
Remove the locks of the
middle tr ay and the lower
tray similarly.
AC cord
1
2
2
2
2
3
3
4
3
Rear mounting plate
Rear mounting plate
Screw
Screw
Screw
Screw
Front
mounting plate
Front mounting plate
Rear cabinet
Rear cabinet
Screw
AC inlet cover
<2> Attach the AC inlet cover
to the rear cabinet of the
stand/paper drawer and fix it
with the removed screw.
Connect the relay h arness of
the stand/paper drawer to the
connector of the power supply
unit.
Connector of the power supply connector
Relay harness of the
stand/paper drawer
Installation is now complete.
<3> Reattach the paper tray
of the main unit.
FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS.
SEE OK I DIGITAL PRINTER SERVICE MANUAL OR
INSTALLATION MANUAL TO DETERMINE SUITABILITY.
[Caution]
For installation of the main unit, it must be
held by two persons and installed carefully.
[Caution]
Insert the rear mounting plates
under the Stand frame.
Attach the power supply unit to the brackets and secure it using the three
supplied screws.
Bracket
Cut out the harness cover as
shown in the illustration.
CN11
13. Carry out the off center adjustment.
Stand frame
Mounting plate
Paper guides
Wire saddle
<2> Con nect the op tional
powe r supp ly har ness
connec tor to CN11 (red
connector) of the PCU PWB of
the main unit of the printer.
• Fix the harness securely to
the wire saddle.
<Before installation>
•
Start instal lation af ter check ing that the DATA and
COMMUNICA TION indic ators on the op eration pa nel are
neither lit nor blinking.
• For installation, a power supply unit (AR-DC1) is needed.
Bracket
* If another peripheral device must be installed, carry out
the following step at the end of the installation work.
Rear guide
4
Loading...