Oki B8300n, B83MP, B83LT, B83TT, B83D Installation Manual

...

Download

Page 1

Page 2

Start of installation

End

B83MP /

Power Suply Unit

... (P. 2)

B83LT /

Power Suply Unit

..... (P. 3)

B83TT /

Power Suply Unit

.... (P. 4)

Main unit

.................................. (P. 5)

B83MP / B83LT / B83TT /

B83D / B83DB.................(P. 14 & 15)

B83D ....................(P. 7)

B83DB ................(P. 8)

B83MB/Power Suply Unit

...

(P. 9)

B83F/Power Suply Unit

.......

(P. 10)

B83SS

....................................

(P. 11)

B83THP / USP / FHP / FBP.(P. 12)

Main unit

Finishing device

Duplex/bypass device

Finishing device

Paper feeding deviceDuplex device Paper feeding device

Installation Manual for B8300

and Its Peripheral Devices

Duplex/bypass

device installed?

Finishing device

installed?

Hard Disk

Yes

1:  When installing a paper feeding device, an optional power supply unit or a duplex/bypass device, be  sure to reattach the rear cabinet, the AC inlet cover, and the harness cover of the main unit at the end  of installation as needed. 2:  When installing electrical devices, be sure to install them one at a time. 3:  Only off center adjustment is needed for B83D.

To install the devices efficiently, follow the procedure below. Some peripheral devices may have been installed as standard devies depending on the main unit model. Part of descriptions and illustrations may be different.

Paper guide position adjustment/off center adjustment

1) Installation of driver software, setting, and operation check

Main unit / B83H..............

(P. 13)

[Electrical setting/adjustment]

Main unit, paper feeding device, and power supply unit.

Install duplex/pypass device.

Install finishing device.

Page 3

<2> Connect the connector of the relay harness of the multi purpose drawer to CN10 (blue connector) of the PCU PWB of the main unit of the printer.

For installation of a finisher or a mail-bin stacker, see its installation manual.

7. Carry out the off center adjustment.

CN10

Rear guide

Paper guide

B83MP Installation Manual

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE OKI DIGITAL PRINTE R SERV ICE MA NUAL O R INSTALLATION MANUAL TO DETERMINE SUITABILITY.

When installing a finisher or a mail-bin stacker with B83MP, a power supply unit is needed.

Front mounting plates:

2 pcs.

Rear mounting plates:

2 pcs.

Screws (M4x8):

4 pcs.

1. Turn off the main switch of the main unit of the printer.

Turn the main sw itch located on th e front side of the main unit to the "OFF" position. Then, remove th e power plug of th e main unit from the outlet.

"OFF"

2. Put the main unit of the printer on the multi purpose drawer.

<1> Pull out the paper tray of the main unit until it stops and then remove it by lifting both ends of the tray.

<2> Hold the main unit of the printer at the positions shown in the illustration and put the main unit on the multi purpose drawer so that the front side and the left side of the main unit are aligned to those of the multi purpose drawer.

Front side

Rear side

[Caution]

For installation of the main unit, it must be held by two persons and installed carefully.

<1>Attach the two rear mounting plates using a supplied screw for each.

3. Connect the main unit of the printer to the multi purpose drawer.

Rear mounting plate

Screw

[Caution]

Insert th e m ounting plate under the tray frame.

Tray frame

Mounting plate

<2> Pull out the multi purpose drawer until it stops and attach the two front mounting plates using a supplied screw for each.

Then, remove the lock of the paper tray and close the tray.

Screw

Front mounting plate

<3> Reattac h the paper tr ay of the main unit of the printer.

<1> Remove the screw that fixes the harness cover of the main unit of the printer and then slide the harness cover up to remove it.

Harness cover

Screw

4. Connect the harness to the main unit of the printer.

Cut out.

* Cut out the harness cover as shown in the illustration.

Connector

5. Attach the harness cover.

Reattach the harness cover to its original position and fix it with the removed screw.

Wire saddle

Harness cover

Screw

* Fix the harness securely to the wire saddle.

Wire saddle

6. Adjust the position of the paper guides of the paper tray.

<2> Press the [MENU] key several times to display "SIZE ADJUSTMENT A" and press the [OK] key.

<3> "MAXIMUM SIZE" is displayed. Pull out the paper tray and extend the paper guides to the maximum. Then, return the paper tray into the main unit and press the [OK] key.

<4> "MINIMUM SIZE" is displayed. Pull out the paper tray again and narrow the paper guides to the minimum. Then, return the paper tray into the main unit and press the [OK] key.

<5> Press the [BAC K/ CLEAR] key to exit the settin g mode.

[Caution]

If the setting above is not carried out, the paper detection function will not operate.

Installation is now complete.

* If another peripheral device must be installed, carry out the following step at the end of the installation work.

Page 4

B83LT Installation Manual

1. Turn off the main switch of the main unit of the printer.

2. Attach the adjusters and adjust them.

3. Put the main unit of the printer on the stand/paper drawer.

<1> Pull out the paper tray of the main unit until it stops and then remove it by lifting both ends of the tray.

Turn the main switch located on the front side of the printer to the "OFF" position. Then remove the power plug from the outlet.

7. Connect the power supply unit harness to the PCU PWB of the main unit of the printer.

8. Connect the relay harness of the stand/paper drawer to the power supply unit.

<1> Pass the cord of the power supply unit through the hole of the rear cabinet and attach t he re ar ca binet to the stand/paper drawer.

9. Attach the rear cabinet of the stand/paper drawer.

Connect the AC cord of th e power supply unit to the inlet connector of the main unit of the printer at the l ocation shown in the illustration.

10. Connect the AC cord of the power supply unit to the main unit of the printer.

<2> Press the [MENU] key several times to display "SIZE ADJUSTMENT A" and press the [OK] key.

<3> "MAXIMUM SIZE" is displayed. Pull out the paper tray and extend the paper guides to the maximum. Then, return the paper tray into the unit and press the [OK] key.

<4> "MINIM UM SIZE" is displayed. Pull out the paper tray again a nd narrow the paper guides to the minimum. Then, return the paper tray into the unit and press the [OK] key.

(The rear guide ne ed not be adjusted.)

[Caution] If the setting above is not car ried out, the pap er detecti on functi on will not operate.

12. Adjust the position of the paper guides of the upper paper tray of the stand/paper drawer.

Remove t he four screw s for packi ng. (See the ri ght illustration.)

Insert the left paper guides and right p aper guides to the front and rear guide sl ots for the paper size to be used. (See the illustration below.)

(For the AB s ystem, set the guides to A4. For the inch system, set the guides to LT.)

11. Attach the paper guides to the lower tray.

"OFF"

<2> Hold the main unit of the printer at the positions shown in the illustration and put the main unit on the stand/paper drawer so that the front side and the left side of the main unit are aligned to those of the stand/paper drawer.

Front side

Rear side

<1> Remove the screw t hat fixes the harness cover of the main unit of the p rinter and slide the harness cover up to remove it.

Cut out the harness cover as shown in the illustration.

<3> Reatta ch the ha rness cover t o its ori ginal position and f ix it with th e removed screw. At this time, e nsure that the optional power supply harness are arranged as shown in the illustration.

<2> Con nect the op tional powe r supp ly har ness connec tor to CN11 (red connector) of the PCU PWB of the main unit of the printer.

Connector

Wire saddle

Harness cover

Optional power supply harness

Screw

Cut out.

Screw

Left adjuster: 1 pc.

Front mounting plates: 2 pcs.

Rear mounting plates: 2 pcs.

Adjuster covers: 4 pcs.

Screws (M4x8):

4 pcs.

Left paper guides: 2 pcs. Right paper guides: 2 pcs.

AC cord

Installation is now complete.

Screw

AC inlet cover

<2> Attach the AC inlet cover to the rear cabinet of the stand/paper drawer and fix it with the removed screw.

Connect the relay h arness of the stand/paper drawer to the connector of the power supply unit.

Connector of the power supply connector

Relay harness of the stand/paper drawer

4. Connect the main unit to the stand/paper drawer.

6. Attach the power supply unit.

5. Remove the rear cabinet of the stand/paper drawer and remove the AC inlet cover.

AC inlet cover

Cut out.

Power supply unit

Screws

<1> Remove the four screws that fix t he rear cabinet and then remove the rear cabinet.

Rear mounting plate

Screw

Front mounting plate

Rear cabinet

<3> Reattach the paper tray of the main unit.

Paper guide

• Fix the harness securely to the wire saddle.

Right paper guides

Left paper guides

Rear cabinet

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE OKI DIGITAL PRI NTER SERVICE MANUAL OR INSTALLATION MANUAL TO DETERMINE SUITABILITY.

CN11

<1> Insert the left adjusters to the stand/paper drawer. <2> Turn ea ch adjuster to lower it until it touches the f loor. <3> Attach the four a djuster covers.

Be sure t o attach th e left adjuster to prevent overturning.

[Cautio n] The lower tray cannot be pulled out unless the adjuster is lowered to the specified position.

[Caution]

For installation of the main unit, it must be held by two persons and installed carefully.

<1>Att ach the two re ar mounti ng plates using a supplied screw for each.

Stand frame

Rear mounting plate

[Caution]

Insert the rear m ounting plates under the Stand frame.

<2>Pull out the upper tray of the stand/p aper drawer until it stops, and attach the two fron t mounting plates using a supplied screw for each.

Then, remov e the lock of the paper tray and close the tray.

<2> Remove the screw that fixes the AC inlet cover and then remove the AC inlet cover.

<3> Cut out the AC inlet cover as shown in the illustration.

Attach the power supply unit to the brackets and secure it using the three supplied screws.

Bracket

* If another peripheral device must be installed, carry out the following step at the end of the installation work.

Paper guides

Rear guide

13. Carry out the off center adjustment.

Wire saddle

• Start installation after checking that the DATA and COMMUNICATION indicators on the operation panel are neither lit nor blinking.

• For installation, a power supply unit is needed.

Page 5

B83TT Installation Manual

1. Turn off the main switch of the main unit of the printer.

2. Attach the adjusters and adjust them.

3. Put the main unit of the printer on the stand/paper drawer.

<1> Pull out the paper tray of the main unit until it stops and then remove it by lifting both ends of the tray.

<1> Insert the left adjusters to the stand/paper drawer. <2> Turn the five adjusters to lower them until they touch the floor. <3> Attach the fou r adjuster covers.

• Be sure to attach the left adju ster to prev ent overturning.

[Caution] The lower tray cannot be pulled out unless the adjuster is lowe red to the specified position.

Turn the main switch located on the front side of the printer to the "OFF" position. Then remove the power plug from the outlet.

Attach the two rear mounting plates using a sup plied screw for each.

4. Connect the main unit to the stand/paper drawer.

6. Attach the power supply unit.

7. Connect the power supply unit harness to the PCU PWB of the main unit of the printer.

8. Connect the relay harness of the stand/paper drawer to the power supply unit.

<1> Pass the cord of the power supply unit through the hole of the rear cabinet and attach t he re ar ca binet to the stand/paper drawer.

9. Attach the rear cabinet of the stand/paper drawer.

Connect the AC cord of th e power supply unit to the inlet connector of the main unit of the printer at the l ocation shown in the illustration.

10. Connect the AC cord of the power supply unit to the main unit of the printer.

<2> After pressing the [MENU] key several t imes to disp lay "SIZE ADJUSTMENT A" in the message display and press the [OK] key.

<3> "MAXIMUM SIZE" is displayed. Pull out the paper tray and extend the paper guides to the maximum. Then, return the paper tray into the unit and press the [OK] key.

<4> "MINIM UM SIZE" is displayed. Pull out the paper tray again a nd narrow the paper guides to the minimum. Then, return the paper tray into the unit and press the [OK] key.

(The rear guide ne ed not be adjusted.)

[Caution]

If the se tting above is not carried out, the paper detection function will not operate.

11. Adjust the position of the paper guides of the upper paper tray of the stand/paper drawer.

"OFF"

Front side

Rear side

<2> Remove the screw that fixes the AC inlet cover and then remove the AC inlet cover.

<3> Cut out the AC inlet cover as shown in the illustration.

5. Remove the rear cabinet of the stand/paper drawer and remove the AC inlet cover.

AC inlet cover

Cut out.

Power supply unit

Screws

<1> Remove the screw th at fixes the harness cover of the main unit of the pr inter and slide the harness cover up to remove it.

<3> Reat tach the har ness cover to its original position and fix it with the removed screw. At this t ime, ensure that the optional powe r sup ply unit harness is arranged as shown in the illustration.

Connector

Wire saddle

Harness cover

Optional power supply harness

Screw

Cut out.

Screw

Left adjuster: 1 pc.

Front mounting plates: 2 pcs.

Rear mounting plates: 2 pcs.

Adjuster covers: 4 pcs.

Screws (M4x8):

4 pcs.

<1> Remove the four screws that fix t he rear cabinet and then remove the rear cabinet.

<2>Pull out the upper tray of the stand/paper drawer until it stops, and attach the two front mounting plates using a supplied screw for each.

Then, remove the lock of the paper tray and close the tray.

Remove the locks of the middle tr ay and the lower tray similarly.

AC cord

Rear mounting plate

Screw

Front mounting plate

Rear cabinet

Screw

AC inlet cover

<2> Attach the AC inlet cover to the rear cabinet of the stand/paper drawer and fix it with the removed screw.

Connect the relay h arness of the stand/paper drawer to the connector of the power supply unit.

Connector of the power supply connector

Relay harness of the stand/paper drawer

Installation is now complete.

<3> Reattach the paper tray of the main unit.

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE OK I DIGITAL PRINTER SERVICE MANUAL OR INSTALLATION MANUAL TO DETERMINE SUITABILITY.

[Caution]

For installation of the main unit, it must be held by two persons and installed carefully.

[Caution]

Insert the rear mounting plates under the Stand frame.

Attach the power supply unit to the brackets and secure it using the three supplied screws.

Bracket

Cut out the harness cover as shown in the illustration.

CN11

13. Carry out the off center adjustment.

Stand frame

Mounting plate

Paper guides

Wire saddle

<2> Con nect the op tional powe r supp ly har ness connec tor to CN11 (red connector) of the PCU PWB of the main unit of the printer.

• Fix the harness securely to

the wire saddle.

•

Start instal lation af ter check ing that the DATA and COMMUNICA TION indic ators on the op eration pa nel are neither lit nor blinking.

• For installation, a power supply unit (AR-DC1) is needed.

Bracket

* If another peripheral device must be installed, carry out the following step at the end of the installation work.

Rear guide

Page 6

B8300 Digital Printer

Main Unit Installation Manual

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE O KI DIGITAL PR INTER SERV ICE MANUAL OR INSTALLATION MANUAL TO DETERMINE SUITABILITY.

1. Select an installation location.

• Installation requirements Selection of installation location is important to the performance of the machine. Consider the following conditions.

• Environment

(1) Avoid locations subject to direct sunlight as plastic parts may be deformed. (2) Avoid high temperature and high humidity locations or where temperatures change rapidly such as near a heater or air conditioner. Rapid changes can cause paper to be become damp and condensation to form within the machine resulting in misfeeds and deterioration of image quality.

(3) Avoid a dusty location and a location subject to vibration. If dust enters the machine, deterioration of image quality or a failure may occur. (4) Do not install the machine in a location that is not stable. Be sure to install the machine on a level surface to maintain proper functions. (5) Avoid poorly ventilated areas. (6) Avoid areas near combustibles or any ammonia present.

• Space around the machine

Install the machine so that the rear side is at least 30 cm form any wall or other object to allow the machine’ cooling fan and ventilation to be effective. Allow sufficient space around the machine for operation and servicing.

• Stand

Ensure that the machine is leveled using a level or the like. If the machine is not placed on a level surface, the toner density control may not function properly, resulting in poor image quality. [Caution] If the machine is not placed on a level surface, the toner density control may not function properly, resulting in bad influence on the quality.

• Grounding

(1) Be sure that the machine is properly grounded. (2) Use a proper ground such as the grounding terminal on an outlet or according to local grounding requirements.

10 30

Humidity

Temperature

Standard conditions: Conditions most adequate for use of the machine

Acceptable temperature and humidity range: 20%Å`85%

Max. 60% at 35Åé

2. Remove the main unit from the carton

(requires two people)

Front side

Rear side

Caution

Removal of t his machine and carryi ng it must be always performed by two persons.

3. Check the parts included.

<1> Check that the following items are included with this machine.

• Drum / Toner cartridge

• Developer cartridge

• CD-ROM

• Safety and Warranty information

• User Guide (may be on CD-ROM)

4. Install the main unit.

<6> Shake the toner /drum cart ridge hori zontally approximately 5 times.

<1> Remove the remainder of packing tape from the operation panel.

<2> Raise the lever of the left door to unlock it and open the left door.

<3> Open the front cover.

<4> Rotate the developer unit lock lever down.

(Be sure to carry out this step after t he paper feeding device has been connected to the main unit.)

One person must lift by the empty front tray pocket with the right hand and steady the machine with the left hand placed at the upper left of the machine. The other person must lift with the right hand by using the lifting recess in the rear of the machine and also steady the machine with the left hand as shown in the illustration.

<3> Remove the pac king tap e from the pa per tray, pull out the paper tray until it stops and remove it by tiltin g i t upward.

<2>

Remove the locking tape from the right and left sidesof the tray. Then,

remove t he top of the carton and lower the plastic b ag covering the

mach ine whi le the mac hine is still on the carton base.

<5> Rem ove th e prot ective cover ing fr om the toner/drum cartridge.

<1> Remove the cushioning materials from the right and left of the front side.

Page 7

<7> Insert the toner/drum cartridge into the main unit.

<8> Remove the drum protective paper in the direction indicated by the arrow.

<11> Remove th e sealing t ape from the toner/drum cartridge by pulling it in the direction indicated by the arrow.

<9>

Remove the supplied developer cartridge from the

packing case and remove the protective materials A and B.

<10> S hake the d eveloper car tridge horiz ontally approximately 5 times and insert it into the machine.

<12> Remove the seali ng tap e from the deve loper cartridge in the direction indicated by the arrow.

<14> Close the front cover.

Gently close the cover.

<15> Apply pressure to the fusing roller.

Raise the right and left levers of the fusing unit in the direction indicated by the arrow.

<16> Close the left door.

<17> Turn the lock pin a 1/4 turn and remove it while pressing down on the pressure plate.

5. Load paper.

<1> Pull out the paper tray.

Gently pull out the paper tray until it stops.

<2> Load paper into the tray.

Do not exceed the maximum height line. (up to 500 sheets of OKI recommended paper can be loaded)

Connecting the machine to a computer.

<1> Connect the machine to the computer

• When connecting to a parallel port: The parallel interface of this machine conforms to IEEE-STD-1284-1983. Use a commercially available shielded type parallel interface cable conforming to the specifications of both the machine and the computer.

The connector on this machine is a 36-pin Amphenol female connector.

For the specifications of the connector on the computer, see the operation manual of the computer.

Parallel interface connector

<2> Insert the power plug into an outlet.

Caution

If the outlet is also used for lighting fixtures, the lighting fixtures may flicker. Use an outlet which is not connected to lighting fixtures.

<3> Turn on the main switch of the main unit.

Automatic level adjustment of toner density sensor will start and a message indicating [WARMING UP] will appear on the operation panel. After the level adjustment is complete, the ready indicator will light up.

Caution

While automatic adjustment of the toner density sensor is being done, do not turn the power to the machine off. This will cause improper adjustment.

7. Check the printer operation

For installation of printer drivers on the computer refer to the Operati on manual (fo r p rinter o peration and genera l information) supplied with the machine. After driver installation, execute a test print to ensure normal printing.

<13> Retur n the developer un it lock to its or iginal position.

Remove t he lock pin while holding down on the p aper pres sure plate a nd in sert the paper tray into the main unit.

* If another peripheral device must be installed, carry out the following step at the end of the installation work.

Page 8

•

Carry out the installation after checking that the DATA indicator on the operation panel is neither lit nor blinking.

• For inst alling B83D, an opti onal de sk (mul ti purpose drawer, stand/3 x 500 sheet paper drawer or stand/MPD & 2000 sheet drawer) must have been installed.

• Ensure that the front mounting plates and the rear mounting plates included with the optional stand/paper drawer are securely attached.

•

Check that the le ft adjuster suppl ied with an

optional stand/drawer has been attached.

1. Turn off the main switch of the main unit of the printer.

Remove the left side cover of the main unit of the printer.

Turn the main switch located on the front side of the main unit of the printer to the "OFF" position. Then, remove the power plug of the main unit of the printer from the outlet.

Unlock th e l ock relea se lever of the main unit of the printer and then pull out the left door. Slide the two upper covers up to remove them. Remove the lower cover by inserting a flat-bl ade screwd river at three locations ( ) shown in the illustration. Then, close the left door.

B83D Installation Manual

<1> Remov e the scre w that fixes the harness cover of the main unit of the p rinter and then slide the harness cover up to remove it.

4. Connect the harness to the main unit of the printer.

Top covers

Lower cover

Left door

<3> Connect the connector of the rel ay harne ss of the duplex modu le to the CN 12 (white connector) of the PCU PWB of the main unit of the printer.

<4> Insert the snap bands to the loc ations shown in the illustration and fix them.

<5>Secure the earth harness using a supplied M4 screw.

<2> Cut out the harness cover as shown in the illustration.

Installation is now complete.

<6> Reatta ch the harness cover to its original p osition and fix it with th e removed screw.

Relay harness connector

PCU PWB

Snap bands

Ground harness

M4 Screw

OFF

Lock release lever

<1> Hang the hooks located at the upper part of the dupl ex module on the openings of the left door of the main unit of the printer.

<2> Push the lower part of the duplex module to ins ert the positi oning bo sses secu rely into the main unit of the printer.

<3> Tight en th e tw o sc rews built in the duplex module.

Attach the duplex module to the main unit of the printer.

Hook

Positioning boss

Hook

Duplex module

Harness cover

Screw

Harness cover

Screw

Cut out.

Harness cover

Relay harness

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE O KI DIG ITAL P RINTER SERVICE MANUAL OR INSTALLATION MANUAL TO DETERMINE SUITABILITY.

Parts included

M4 Screws

(M4x8) : 1 pcs.

5. Carry out the off center adjustment.

CN12

* If another peripheral device must be installed, carry out the following step at the end of the installation work.

Page 9

B83DB Installation Manual

5. Attach the exit tray.

Adjust the position of the paper guides of the bypass tray.

1. Turn off the main switch of the main unit of the printer.

Remove the left side cover of the main unit of the printer.

Turn the main switch located on the front side of the main unit of the printer to the "OFF" position. Then, remove the power plug of the main unit of the printer from the outlet.

Unlock the lock release lever of the main unit of the printer and then pull out the left door. Slide the two upper covers up to remove t hem. Remov e the lo wer cover by inser ting a f lat-bla de screwdriver at three locations ( ) shown in the illustration. Then, close the left door.

<1> Hang the hooks located at the upper part of th e dup lex module on the openings of the left door of the main unit of the printer.

<2> Push the lower part of the duplex modu le to in sert the positioning bosses securely into the main unit of the printer.

<3> Tighten the two screws built in the duplex module.

Attach the duplex module to the main unit of the printer.

<1> Remove the scr ew that fixes the harness cover of the main unit of the printer and then slide the harness cover up to remove it.

4. Connect the harness to the main unit of the printer.

Top covers

Lower cover

Left door

<3> Connect the connector of the re lay ha rness of th e duplex m odule to the CN12 (white connector) of the PCU PWB of the main unit of the printer.

<4> Insert the snap bands to the l ocations show n in the illustration and fix them.

<5>Secure the earth harness using the supplied M4 screw.

<2> Process the harness cover as shown in the illustration.

<6> Reattach the harness cover to its original position and fix it with the removed screw.

OFF

Lock release lever

Harness cover

Screw

Harness cover

Screw

Cut out.

Harness cover

Hook

Positioning boss

Hook

Duplex module

Parts included

Exit tray

Relay harness

<1> To use the setting mode, insert the power plug of the main unit of the printer to the outlet and turn the main switch on while pressing the [MENU] key and the [OK] key of the operation panel of the main unit of the printer. <2> After pressing the [MENU] key several times to display "SIZE ADJU STMENT A " in t he messa ge display, press the [ ] key to display "SIZE ADJUSTMENT B" and press the [OK] key. <3> "MAXIMUM SIZE" is displayed. Since "MAXIMUM SIZE" is displayed with a number, press the [ ] key or the [ ] key to change the number so that the number is equal to the value of [MAX] written on the label

( NOTE)

and then press the [OK] key. <4> Since "P1 SIZE" is displayed with a number, press the [ ] key or the [ ] key to change the number so that the number is equal to the value of [P1] written on the label

( NOTE)

and then press the [OK] key. <5> Since "P2 SIZE" is displayed with a number, press the [ ] key or the [ ] key to change the number so that the number is equal to the value of [P2] written on the label

( NOTE)

and then press the [OK] key. <6> Since "MINIMUM SIZE" is displayed with a number, press the [ ] key or the [ ] key to change the number so that the number is equal to the value of [MIN] written on the label

( NOTE)

and then press the [OK] key.

[Caution]

If the setting above is not carried out, the paper detection function will not operate.

"ON"

Label

( NOTE) Illustration of label sticking position

Installation is now complete.

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE OK I DIGITAL PRINTER SERVICE MANUAL OR INSTALLATION MANUAL TO DETERMINE SUITABILITY.

M4 Screws :

1 pcs.

• Carry out the installation after checking that the DATA indicator on the operation panel is neither lit nor blinking.

• For installing B83DB, an optional desk (multi purpose drawer, sta nd/3 x 500 sheet paper drawer or stand/MPD & 20 00 sheet drawer) must have been installed.

• Ensure that the front mounting plates and the rear mount ing plates inclu ded with the optiona l s tand/paper drawe r a re securel y attached.

• Check that the left adjuster supplied with an optional stand/drawer has been attached.

Relay harness connector

PCU PWB

Snap bands

Ground harness

M4 Screw

CN12

7. Carry out the off center adjustment.

MAX MINP1 P2

(Back surface of the bypass tray extension)

* If another peripheral device must be installed, carry out the following step at the end of the installation work.

Page 10

B83MB Installation Manual

1. Turn off the main switch of the main unit of the printer.

2. Remove the upper cabinet of the stand/paper drawer.

<1> Pull out the paper tray of the stand/paper drawer. Remove the four screws of the cabin et attached to the right side of the main unit of the prin ter and rem ove the cabinet.

Turn the main switch located on the front side of the main unit to the "OFF" position. Then, remove the power plug of the main unit from the outlet.

11. Connect the AC cord of the optional power supply unit to the main unit of the printer.

<2> Mount screw B to the positio n shown in the illustration.

3. Attach the mail-bin stacker.

<1> Remove the paper exit actuator from the main unit of the printer.

<2> Raise the relay unit at the side of the mail-bin stacker.

<3> Hold the grip of the mailbin stacker and place the mailbin stacker on the stand/paper drawer temporarily.

Then, push the lower part to attach the mail-bin stacker by sliding it toward the exit tray of the main unit.

At this time, align the mail-bin stacker with the exterior line of the stand/paper drawer.

5. Process the AC inlet cover attached to the rear cabinet of the stand/paper drawer.

<1> Remove t he screw that fixes the harness cover of the main unit of the printer and slide the harness cover up to remove it.

Harness cover

Screw

Mounting plates: 2 pcs.

Tray: 1 pc.

Screw B: 1 pc.

<4> Open the front cover of the mail-bin stacker and fix th e stacker with three screws A at the posit ions shown in th e illustration. Then, close the front cover and close t he paper tr ay of the stand/paper drawer.

<5> Attach the mounting plates to the posit ions s hown i n the illustra tion an d fix them with screws A.

9. Arrange the harness of the mail-bin stacker.

<2> Connect the power supply unit harne ss conn ector to CN11 (red connector) of the PCU PWB of the main unit of the printer.

<3> Reat tach the har ness cover to its origin al position and fix it with the removed screw. At this time, ensure that the power supply unit harness is arranged as shown in the illustration.

Wire saddle

Harness cover

Optional power supply harnesses

Screw

4. Attach the tray.

6. Attach the power supply unit.

Optional power supply unit

Screws

Connector

<1> Pass the harness of the mail-bin stacker between t he power sup ply u nit and the frame of the stan d/paper drawer and connect it to the connector of the power supply unit.

<2> F it the s nap band attach ed to the mail- bin stacker at the position shown in t he illust ration to fix the harness.

<1> Connect the AC cord of the power supply unit to the inlet connector of the main unit of the printer at the l ocation shown in the illustration.

7. Connect the power supply unit harness to the PCU PWB of the main unit of the printer.

<1> Pass the AC cord of the power supply unit as shown in the illustration and fi x t he rear ca binet of t he stand/paper drawer with the screws.

10. Attach the rear cabinet of the stand/paper drawer.

<2> Attach the AC inlet cover to th e rear cabinet of the stand/paper drawer and fix it with the removed screw.

Screw

AC inlet cover

Rear cabinet

AC cord

Cabinet

Mounting plate

Screws A

Screw A

Tray

Power supply unit connector

Snap band

Mail-bin stacker harness

Installation is now complete.

• Star t ins tallation aft er ch ecking that the D ATA a nd COMMUNICAT ION indicators on the operation pa nel are neither lit nor blinking.

• For installation of B83MB, an optional stand/paper drawer (stand/MPD & 2000 sheet paper drawer, stand/3 x 500 sheet paper drawe r or multi purpos e drawer) must hav e been installed. Also if a multi purpose drawer has been installed, a power supply unit is needed additionally.

Screws A (M4x8): 5 pcs.

"OFF"

Screw B

Actuator

Relay unit

Screw

• Fix the harness securely to

the wire saddle.

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE OKI D IGITAL PRINTER SERVICE MANUAL OR INSTALLATION MANUAL TO DETERMINE SUITABILITY.

[Caution]

Do not press on the relay unit while it is raised. (Doing so ma y deform or damage the unit.)

Steps 5 and after are the procedure to be carried out when a multi purpose drawer has been installed. If a stand/MPD & 2000 sheet paper drawer or a stand/3 x 500 sheet paper drawer has been installed, carry out steps 8 and after.

Remove the two screws that secure the rear cabinet and remove the rear cabinet.

Remove the screw that fixes the AC inlet cover and then remove the AC inlet cover.

Process the AC inlet cover as shown in the illustration.

(Front side)

(Rear side)

8. Remove the AC inlet cover and then remove the rear cabinet of the stand/paper drawer.

<1> Remove the screw that fixes the AC inlet cover and then remove the AC inlet cover.

<2> Remove the AC cord of the power supply unit from the inlet connector of the main unit of the printer. Remove the four screws that fix the rear cabinet and then remove the rear cabinet.

Screw

AC inlet cover

Rear cabinet

Ç–Ç¡Ç©ÇØïî

Attach the power supply unit to the brackets and secure it using the supplied three screws.

Wire saddle

(* Similar work for the multi purpose drawer)

[Caution] Insert th e mounting

plate under the desk frame.

Stand frame

Mounting plate

Push.

Place.

Grip

Cut out.

AC inlet cover

Screw

Rear cabinet

Bracket

CN11

(* Similar work for the multi purpose drawer)

Page 11

B83F Installation Manual

1. Turn off the main switch of the main unit of the printer.

2. Remove the upper cabinet of the stand/paper drawer.

<1> Pull out the tray of the stand/paper drawer. Remove t he four screws attached to the right on the top of the stand/ paper drawer and remove the cabinet.

Turn the main switch located on the front side of the main unit to the "OFF" position. Then, remove the power plug of the main unit from the outlet.

12.

<2> Mount screw B to the positi on sho wn in the illustration.

3. Attach the finisher.

<1> Remove the paper e xit actuator from the main unit of the printer.

<2> Raise the relay unit at the side of the finisher.

<3> Hold the grip of the finisher and pl ace the finisher on the stand/paper drawer temporarily.

Then, push t he lower part to attach the finis her by sliding it toward the exit tray of the main unit.

At this time, align the finisher with the ex terior line o f t he stand/paper drawer.

6. Process the AC inlet cover attached to the rear cabinet of the stand/paper drawer.

<1> Remove the screw that fixes the harness cover of the main unit of the printer and slide the harness cover up to remove it.

Process th e harness cov er as shown in the illustration.

Harness cover

Screw

Mounting plates: 2 pcs.

Staple cartridge: 1 pc.

Tray 1: 1 pc.

Screws A (M4x8): 5 pcs.

Screw B: 1 pc.

<4> Open the front cover of the finisher and fi x the finisher with three screws A at the positions shown in the illustration. Then, c lose the front co ver and close the pap er tray of the stand/paper drawer.

<5> Attach the mounting plates to the positions shown in the illustration and fix them with screws A.

10. Arrange the harness of the finisher.

<2> Connect the pow er supply unit harness connector to CN11 (red connector) of the PCU PWB of the main unit of the printer.

<3> Reattach the harness cover to its original position and fix it with the removed screw. At this time, ensure that the power supply unit harn ess i s arrange d as sho wn in t he illustration.

Wire saddle

Harness cover

Optional power supply harnesses

Screw

5. Attach the trays .

4. Insert the staple cartridge.

7. Attach the power supply unit.

Optional power supply unit

Screws

Connector

<1> Pass the harness of the finishe r betwe en the powe r supply unit and the frame of the stand/paper drawer and connect

it to the connector of the power supply unit.

<2> Fit the snap band attached to the finisher at the position shown

in t he illu stration to fix t he harness.

<1> Connect the AC cord of the power supply unit to the inlet connector of the main unit of the printer at the locati on show n in the illustration.

Remove the two screws th at secure the rear cabinet and remove the rear cabinet.

Remove the screw that fixes the AC inlet cover and then remove the AC inlet cover.

Process the AC inlet cover as shown in the illustration.

8. Connect the power supply unit harness to the PCU PWB of the main unit of the printer.

<1> Pass the AC cord of the power supply unit as shown in the illustration and fix the rear cabinet of the stand/paper drawer with the screws.

11. Attach the rear cabinet of the stand/paper drawer.

<2> Attach the AC inlet cover to the rear cabi net of the stand/paper drawer a nd fix it with the removed screw.

Screw

AC inlet cover

AC cord

Cabinet

Mounting plates

Screws A

Snap band

Finisher harness

Installation is now complete.

Tray 1

Tray 2

• Start installation after checki ng that th e DATA and COMMUNICATION indicators on the operation panel are neither lit nor blinking.

• For installation of B83F, an optional stand/paper drawer (stand/MPD & 2000 sheet paper drawer, stand/3 x 500 sheet paper drawer or multi purpose drawer) must have been installed. Also if a multi purpose drawer has been installed, a power supply unit is needed additionally.

Tray 2: 1 pc.

"OFF"

Actuator

Relay unit

• Fix the harness securely to the wire saddle.

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE OKI DIG ITAL PRI NTER SE RVICE MA NUAL OR INSTALLATION MANUAL TO DETERMINE SUITABILITY.

Connect the AC cord of the optional power supply unit to the main unit of the printer.

[Caution] Insert the mount ing plate

under the desk frame.

(Front side)

(Rear side)

10. Remove the AC inlet cover and then remove the rear cabinet of the stand/paper drawer.

<1> Remo ve the sc rew that fixes the AC inlet cover and then remove the AC in let cover.

<2> Remove the AC cord of the power supply unit from the inlet connector of the main unit of the printer. Remove the four screws that fix the rear cabinet and then remove the rear cabinet.

Screw

AC inlet cover

Rear cabinet

Screw B

<1> Pull out the staple unit.

<2> Remove the sealing tape from the staple cartridge.

<3> Insert the staple cartridge. <4> Slide the release lever to the left and return the staple unit.

Power supply unit connector

[Caution]

Do not press on the relay unit while it is raised. (Doing so may deform or damage the unit.)

Attach tray 1 and tray 2 to the positions shown in the illustration.

AC inlet cover

Wire saddle

(* Similar work for the multi purpose drawer)

Push.

Place.

Grip

Stand frame

Mounting plate

Cut out.

AC inlet cover

Attach the power supply unit to the brackets and secure it using the supplied

three screws.

CN11

Wire saddle

Stapling position labels:

2 sheets

Steps 6 and after are the procedure to be carried out when a multi purpose drawer has been installed. If a stand/MPD & 2000 sheet paper drawer or a stand/3 x 500 sheet paper drawer has been installed, carry out steps 9 and after.

Bracket

Page 12

Staple unit: 1 pc.

Connecting plate:

1 pc.

Front grounding

plate: 1 pc.

Rear grounding

plate: 1 pc.

Front cover:

1 pc.

Screws C

Exterior fixing screw

Front grounding plate

Rear grounding plate

<1> Remove the screw from the right side of the duplex module.

<2> Atta ch the loc k securing plate to the duplex module using the screws C and D (one for each).

9. Paste the stapling position labels.

Paste the labels to the positions shown in the illustration.

<1> Attach the plate R to the position shown in th e illustrati on and secur e it using two screws A.

<2> Attach the front cover to the finisher, and secure the upper part using two screws B and the l ower part using two screws A.

<1> Remove the two piece s of packing tape f rom the locations shown in the illustration.

Packing tape

B83SS Installation Manual

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE OKI DIG ITAL PRI NTER SE RVICE MA NUAL OR INSTALLATION MANUAL TO DETERMINE SUITABILITY.

<Before installation> For instal lation of B83SS , an op tional stand/p aper drawer (stand/MPD & 2000 shee t drawer or sta nd/3 x 500 shee t paper drawer) and a duplex module B83D must have been installed. Also a power supply unit is needed.

Plate R: 1 pc.

Lock securing plate:

1 pc.

Screws A (M4x6):

6 pcs.

Screws B (M4x10):

2 pcs.

Screws C

(M4x18):

7 pcs.

Screws D

(M4x10 with rosette):

1 pcs.

"OFF"

1. Turn off the main switch of the main unit of the printer.

Turn the main switch located on the front side of the main unit to the "OFF" position. Then remove the power plug of the main unit from the outlet.

Screw D

Screw C

Lock securing plate

Screw

3. Work the stand/paper drawer.

Mounting holes

Left adjuster

Remove the two screws that fix t he exterior of the stand/paper drawer.

Then, at tach the fr ont mounting plate and the rear mounting plate to the stand/paper drawer using screws C (two for each).

4. Attach the grounding plate to the stand/paper drawer.

5. Install the staple unit to the finisher.

<2> Open the front cover of the finisher and insert the staple unit.

Front cover

Screws A

Screws B

Plate R

7. Connect the finisher to the stand/paper drawer.

<1> Remove the cover from the finisher stand.

<2> Attach the conne cting plate to the finisher using two screws A.

<3> Reattach the cover to its original position.

Cover

Screws A

Screws C

Connecting plate

Stand/paper drawer

8. Check and adjust the height of the finisher.

Guide pin

Connecting hole

Move the finisher toward the printer and check to see if the guide pin of the locki ng pla te is ins erted smoothly to the connecting hole of the finisher. If it is not inserted smoothly, use the following procedure to a djust the height.

2. If the guide pin of the locking plate matches to the connecting hole of the finisher:

Finisher stand

Gap

Sub cover

Screw

Screw at adjusting portion

Height adjusting screw

Screw at adjusting portion

Cap

Front side

Rear side

Height adjusting screw

Screw at adjusting portion

Cap

Front side

Rear side

Front cover

Exterior lines

10. Remove the AC inlet cover from the rear cabinet of the stand/paper drawer.

Remove the screw that fixes the AC inlet cover and then remove the AC inlet cover.

Screw

AC inlet cover

11. Connect the finisher connector.

<1> Con nect the f inisher connector to the stand/paper drawer.

<2> Tighten the screw of the connector.

Screw

Connector

12. Turn on the main switch of the main unit.

Insert the power plug of the main unit to the outlet.

Turn on the main switch of the main unit.

Installation is now complete.

"ON"

2. Attach the lock securing plate to the duplex module.

6. Attach the cover to the finisher.

Stapling position labels:

2 sheets

Open the pawl of the left adjuster to both sides to unlock it that is located at the lower left of the stand/paper drawer and remove the left adjuster.

Cut out the two mounting holes of the stand/paper drawer using a screwdrive r or the like and remove burrs using a flat-blade screwdriver or the like.

Pawl

Connecting plate

Finisher stand

1. If the guide pin of the lock securing plate is not aligned with the connecting hole of the finisher:

<1>Push the finisher into the main unit.

<1> Loosen the screw at the rear adjusting portion.

<2> Remove the cap using a flat-blade screwdriver or the like a nd adjust t he height adjusting pin so that the guide pin is positioned to the c enter of the connecti ng ho le of the finisher.

<3> Loosen the screw at the front adjusting portion.

<4> A djust th e height adjusting pin so that the exterior lines are aligned as shown in the illustration.

<5> If the guide pin can be inserted smoothl y, tighten the screws at the front and rear adjusting portions and mount the caps.

<2>If the gap between the main unit of the printer and the finisher is not uniform at the top an d th e bo ttom, remove the caps from the front side and the rear side of the finisher stand using a flatblade screwdriver or the like and remove the screw of the sub covers on the front side and the rear side to remove the sub covers.

<3>Then, loosen the four screws at th e a djusting portion s indica ted in the illustration and turn the height adjusting screws on the front side and the rear side so that the gap becomes uniform.

<4>If the gap becomes uni form, tighten the screws at the adjustin g portions and reattach the caps and sub covers.

<4> Cut out the t wo mounting holes for the connecting plate at the lower part of the stand/paper drawer in a similar way to step 3.

<5> Attach the fi nisher conne cting plate to the stand/pape r drawer usin g two screws C.

Page 13

Staple unit

Screws

Front cabinet

Parts included

1. Turn off the main switch of the main unit of the printer.

Remove the front cover from the right front of the finisher.

Turn the main switch located on the front side of the main unit to the "OFF" position. Then remove the power plug of the main unit from the outlet.

Loosen the screw and remove the connector of the finisher.

"OFF"

Screw

(M4 x 6 with rosette)

: 1 pc.

Harness A (purple): 1 pc.

Harness B (orange): 1 pc.

Dust box label:

1 sheet

<1> Remov e th e fo ur t op c over securing screws and remove the top cover.

8. Reattach the front cover to the right front of the finisher.

7. Reattach the covers that have been removed.

6. Connect the harness of the punch module to the PWB of the finisher.

5. Attach the punch module.

4. Remove the top cover.

Installation is now complete.

Screws B

Screws A

Front cover

<3> Remove the three screws that fix the rear cabinet and remove the rear cabinet. At this time, remove the relay harness through the opening of the rear cabinet.

<1> Open the front door of the finisher and remo ve the ja m handling dial.

3. Remove the front cabinet and the rear cabinet from the finisher.

Jam handling dial

Staple unit

Screws

Front cabinet

Screw

Relay harness

Opening for relay harness

Screw

Rear cabinet

Screw

Relay harness

Opening for relay harness

Screws

Rear cabinet

<2> R emove the four pawls from t he top c over and separate th e cove r into the upper and lower port ions. Reuse the upper portion.

Top cover

Lock release lever (A)

Projection (B)

Latch arm

Pawl (D)

Screw

Top cover

<Before installation> For installation of B83THP / USP / FHP / FBP, a saddle stitch finisher B83SS must have been installed.

<2> Re move the four f ront cabinet securing screws, pull out the staple unit until it stops, then remove the pawl of the front cabinet in the direction indicated by the arrow an d remove the front cabinet.

<4> Remove the three rea r cabine t secu ring screws , remove the pawl in the directio n ind icated by the arrow, and remove the r ear cabinet. At this time, remove the relay harness through the opening of the rear cabinet.

Screws

Connector

AC cord

Hole punch position label:

2 sheets

Screws

Connector

Pawl

9. Paste the dust box label to the top cover.

Remove the c lamps that fix the harness, handle the wiring of harness A (purple ) an d harness B (o range), and fix them with the clamps.

Paste the supplied dust box label to the location indicated in the illustration.

<1> Insert the two bosses of the punch unit into the boss holes of the finisher and fix the punch module using three screws.

(Note)

For the screws, use a supplied screw and the two screws that have been removed in step 4.

Top cover

Screws

Boss

Boss hole

Boss

Boss hole

Screw (with rosette) (supplied with this module)

Screw

Punch module

<4> Reatt ach th e jam handling dial and close the front cover.

Clamps

Harness A (purple)

Harness B (orange)

Harness A (purple)

Harness B (orange)

Jam handling dial

B83THP / USP / FHP / FBP

Installation Manual

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE OKI DIG ITAL PRI NTER SE RVICE MA NUAL OR INSTALLATION MANUAL TO DETERMINE SUITABILITY.

10. Connect the connector to the stand/paper drawer and connect the AC cord of the power supply unit to the main unit of the printer.

Connect the connector of the relay harness of the finisher to the stand/ paper drawer an d tighten the screws of the connector.

(C)

Remove the screws A and B (two for each) that secure the finish er fron t cover and remove the front cover.

Screws B

Screws A

Front cover

Pawl

<1> Hang the two paw ls of the top cover and sec ure them using the two screws. <2> Pass the relay harness to the rear cabinet and secure the rear cabinet using the three screws. <3> Remove the lock release lever that has been attached to the front cabinet. Reattach the front cabinet to its original pos ition, push in the staple unit, and attach it using the two screws. Insert the protrusion (B) of the lock re lease lever that has been removed before to the hole (C) of the latch arm.

After attach ing it, move the lever to check that it moves smoothly.

If the lever does not move smoothly, remov e the lock release lever by releasing the pawl at the lower part of the lock release lever using a flatblade screwdriver or the like and then insert it again.

Attach the front cover using the screws A and B (two for each).

Pawl

Page 14

1. Turn off the main switch of the main unit of the printer.

2. Remove the cables connected to the control PWB unit.

(Example) MFP control PWB

7. Turn on the main switch of the main unit of the printer.

4. Mount the HDD expansion PWB to the control PWB.

8. Check the operation.

5. Attach the control PWB.

Turn the main swit ch located on the fron t side of the main unit to the "OFF" position.

Then remo ve th e power plug from the outlet.

Insert the powe r plug of the main unit of the printer to the outlet.

Then, tur n the main swi tch located on the front side of the main unit to the "ON" position.

• For setting change of the printer drivers on the computer, see the supplied operation manual.

Then, execute printing from the computer using the print hold function to check for proper printing.

Remove all the cables connected to the control PWB unit of the main unit of the printer.

3. Remove the control PWB unit.

Remove the five screws that fix the contr ol PWB unit to the main unit of the printer. Then, hold the two grips and pull out the printer cont rol PWB unit to remove it from the main unit.

Attach the control PWB unit to the main unit of the printer and fix it using five screws.

6. Connect the cables to the control PWB.

Connect all the cables that have been removed in step 2 to the original positions of the printer control PWB unit.

<1> Remove the screw at the position shown in the illustration among the screws that secure the hard disk to the HDD expansion PWB. <2> Attach the supplied grounding plate to the HDD PWB as shown in t he illustration and secure it using the screw that has been removed in step <1>. <3> Remove th e thr ee sc rews shown in the i llustration am ong the screw s th at fix the p rinter control PWB. <4> Mount supplied three PWB fixing screws to the positions from which three screw s have been removed. <5> In sert th e HDD expans ion PWB t o the connec tor of the printer control PWB. <6> Fix the HDD expansion PWB to the PWB fixing screws using the three screws that have been removed in step 1. <7> Secure the grounding plate that has bee n attache d to th e HDD expansion PWB to the con troller mounting plate using the supplied screw.

<1> Remove th e thre e screws shown in the il lustration among the screw s that f ix the MFP control PWB. <2> Mount supplied three P WB fixing screws to the positions from which three screw s have been removed. <3> In sert the HDD expansi on PWB to the connector of the MFP control PWB. <4> Fix the HDD expansion PWB to the PWB fixing screws using the three screws that have been removed in step 1.

Parts included

PWB fixing screws: 3 pcs.

"OFF"

"ON"

• St art instal lation aft er c hecking tha t th e DATA and COMMUNICATION ind icators on the operation p anel a re neither lit nor blinking.

• In case of printer control PWB ..................................................................................

• In case of MFP control PWB ......................................................................................

• The procedure (shape of PWB) varies with the printer control PWB and the MFP control PWB.

Screws

• In case of printer control PWB

• In case of MFP control PWB

Grip

Screws

B83HD Installation Manual

HDD expansion PWB

Grounding plate

: 1 pcs.

screws: 1 pcs.

HDD expansion PWB

* If another peripheral device must be installed, carry out the following step at the end of the installation work.

"OFF"

"ON"

FOR USE WITH COMPATIBLE OKI DIGITAL PRINTERS. SEE OK I DIGIT AL PRIN TER SER VICE MA NUAL OR INSTALLATION MANUAL TO DETERMINE SUITABILITY.

Page 15

Applied model: Main unit

Applied model: B83HD

For setting change of the printer drivers on the computer, see the supplied operation manual. Then, execute printing from the computer using the print hold function to check for proper printing.

<1> Insert the power plug into an outlet.

Caution

If the outlet is also used for lighting fixtures, the lighting fixtures may flicker. Use a n out let w hich i s not conn ected to light ing fixtures.

<2> Turn on the main switch of the main unit.

Automatic level adjustment of toner density sensor will start and a messag e indic ating [WARMING UP] will appear on the operation panel. After the level adjustment is complete, the ready indicator will light up.

Caution

While automatic adjust ment of the toner d ensity sensor is being done, do not turn the power to the machine off. This will cause improper adjustment.

<3>Check the printer operation

For installation of printer drivers on the computer refer to the Operation manual (for printer operation and general information) supplied with the machine. After driver installation, exe cute a test print to ensure normal printing.

Electrical Setting/ Adjustment/ Operation Check

Carry out installation of driver software and check of printing

Carry out i nstallati on of dri ver softwa re an d check of printing

•

[1]Installation of driver software, setting, and operation check

[2]Paper guide position adjustment and off center adjustment

For Printer Models

[Applied models]

B83MP/ B83LT / B83TT/ B83D / B83DB

Applied models: B83MP/ B83LT / B83TT

Paper guides

<2> Press the [MENU] key several times to display "SIZE ADJUSTMENT A" and press the [OK] key.

<3> "MAXIMUM SIZE" is displayed. Pull out the paper tray and extend the paper guides to the maximum. Then, return the paper tray into the main unit and press the [OK] key.

<4> "MINIMUM SIZE" is displayed. Pull out the paper tray again and narrow the paper guides to the minimum. Then, return the paper tray into the main unit and press the [OK] key.

[Caution]

If the setting above is not carried out, the paper detection function will not operate.

Adjust the p osition of th e paper guide s of the paper tray of B83MP or the upper paper tray of stand/paper drawer B84LT / B83TT.

Rear guide

Applied model: B83DB

MINP1 P2

MAX

Adjust the position of the paper guides of the bypass tray.

<2> After pressing the [M ENU] key several times to display "SIZE ADJUSTMENT A" in the message display, press the [ ] key to display "SIZE ADJUSTMENT B" and press the [OK] key.

<3> "MAXIMUM SIZE" is displayed. Since "MAX IMUM SIZE" i s displayed with a numb er, press the [ ] key or the [ ] key to change the number so that the number is equal to the value of [MAX] written on the label

( NOTE)

and then press the [OK] key.

<4> Since "P1 SIZE" is displayed with a number, press the [ ] key or the [ ] key to change the number so that the number is equal to the value of [P1] written on the label

( NOTE)

and then press the [OK] key.

<5> Since "P2 SIZE" is displayed with a number, press the [ ] key or the [ ] key to change the number so that the number is equal to the value of [P2] written on the label

( NOTE)

and then press the [OK] key.

<6> Since "MINIMUM SIZE" is displayed with a number, press the [ ] key or the [ ] key to change the number so that the number is equal to the value of [MIN] written on the label

( NOTE)

and then press the [OK] key.

[Caution]

If the setting above is not carried out, the paper detection function will not operate.

"ON"

Label

( NOTE) Illustration of label sticking position

(Back surface of the bypass tray extension)

Then, carry out the off center adjustment.

•

Page 16

Carry out the off center adjustment.

3

TEST PRINT 00

MULTI SETTING

PRINT PATTERN

CASSETTE

DUPLEX

OFF CENTER ADJ

•

TRAY 2

•

LCC

•

1

LCC

•

1

LCC

•

1

TRAY 2

•

1

TRAY 1

USE

ADU

•

TRAY 1

USE

ADU

•

1

DESK 1

•

1

DESK 2

[MENU] key

B83MP

B83LT B83TT

B83D

•

BPT

MFT

B83DB

(*1) Load paper only in the left tray. (*2) Load paper only in the right tray.

T4(*2)

T3(*1)

Main unit

TRAY 1 (T1)

TRAY 2 (T2)

DESK 1 (T3)

DESK 2 (T4)

TRAY 2 (T2)

LCC (T3)

LCC (T4)

TRAY 2 (T2)

BPT (MFT)

(ADU)

(Fig. 1)

(Fig. 2)

Center of paper

Top end of paper

Center of paper

Top end of paper

Example of image

[Rear side of the main unit]

Applied models: B83MP / B83LT / B83TT / B83D / B83DB

<1> To select the setting mode, insert the power plug of the main unit of the printer into an outlet and turn on the main switch while pressing the [MENU] key and the [OK] key simultaneously. When carrying out the off center adjustment after paper guide position adjustment, this operation is not needed. (For B83D, this operation is needed.)

<2> Press the [MENU] key repeatedly until "TEST PRINT 00" is displayed, and press the [OK] key.

<3> Use the [MENU] key to select "MULTI SETTING" and enter "1" using the [ / ] key.

<4> Use the [MENU] key to select "PRINT PATTERN" and enter "1" using the [ / ] key.

<5> Use the [MENU ] key to select "CAS SETTE" and select the tray for which the off center adjustment is to be carried out using the [ / ] key. (See the table below.)

<6> Use the [MENU] key to select "DUPLEX" and select

"USE" or "NO" using the [ / ] key. (See the table below.)

<7> Use the [MENU] key to select "** OFF CENTER ADJ" corresponding to the option in the table below, press the [OK] key, and check that the printed line is positioned at the center of paper.

<8> If the off center is displaced, use the [ / ] key to adjust the value so that the line is positioned at the center. (Fig. 1 and 2)

Default: 50 (setting range: 0 to 99) Increase of the value shifts the overall image toward the rear side. Value 1 corresponds to 0.1 mm.

<9> Turn off the main switch of the main unit of the printer and then turn on the switch again after several seconds.

The setting is now complete.

Setting example for each model

Center line of image (first print image) In this case, increase the value.

Center line of image (first print image) In this case, decrease the value.

•

■

Oki B8300n, B83MP, B83LT, B83TT, B83D Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual