Page 1
Mounting Instructions
Before installing this product, read the Öhlins Owner’s Manual!
In
s
t
a
ll
in
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
is
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
ic
le
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
fe
c
t
t
h
e
s
t
a
b
il
it
y
o
f
y
o
u
r
v
e
h
ic
le
.
In
s
t
a
ll
in
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
is
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
ic
l
e
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
il
it
y
o
f
y
o
u
r
v
e
h
ic
le
.
I
n
s
t
a
ll
in
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
is
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
ic
le
m
a
n
u
fa
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
il
it
y
o
f
y
o
u
r
v
e
h
ic
le
.
In
s
t
a
ll
in
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
is
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
ic
l
e
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
il
it
y
o
f
y
o
u
r
v
e
h
ic
le
.
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden. Phone +46 8 590 025 00 Fax +46 8 590 025 80
www.ohlins.com
with set-up data
Kit Contents:
Part no. Pcs.
Steering Damper SD197 1
Bracket assy 02230-01 1
Screw/Spacer M6 02274-02 2
Screw MC6S 6x25 01046-17 1
Spacer 02259-01 1
Nut M6 00430-02 2
Clamp long, fork leg 02235-50 1
Bracket, frame 02272-22 1
Screw K6S M8x20 05404-02 2
Öhlins Sticker yellow 00192-01 2
Öhlins Sticker blue 00194-10 2
Owner’s Manual 07261-02 1
Before installing this shock absorber,
check the contents of the kit listed
below. If anything is missing, please
contact your nearest Öhlins dealer.
ÖHLINS STEERING DAMPER KIT SD197
for Ducati 848
During storage and transportation,
especially at high ambient temperature,
some of the oil and grease used
for assembling may leak and stain
the packaging. This is in no way
detrimental to the product, wipe off the
excessive oil/grease with a cloth.
Page 2
1
Put the motorcycle on a workstand so that the
front wheel barely touches the ground.
WARNING!
Make sure the vehicle is securely supported so
that it will not tip.
2
Remove the two screws to the black cover in
front of the tank. Use the screws (02274-02)
provided to fasten the cover.
3
Install the frame bracket. Use the nuts (00430-
02) provided in this kit.
4
Install the fork leg clamp bracket to the right
fork leg on top of the triple clamp. Use the
screw (01046-17) provided in this kit.
5
Install the bracket assembly to the frame
bracket. Use the teflon spacer and the screw
(05404-02) provided in this kit.
6
Install the Öhlins steering damper centered to
the bracket assembly.
7
Install the steering damper end eye to the
triple clamp bracket. Use the screw (05404-02)
provided in this kit.
HOW TO INSTALL
8
Adjust the fork leg clamp bracket so that the
steering damper uses similar stroke lengths
both ways.
NOTE!
Make sure that there is enough clearance when
turning the steering damper to the left and right
end positions, and that the damper is not used
as a stop.
9
Tighten the screws to the correct torque:
M5 5 Nm
M6 8 Nm
M8 25 Nm
10
Set the steering damper to the recommended
click position.
WARNING!
Make sure that all screws are tightened to the
correct torque and that nothing fouls or restricts
movement of the shock absorber when the suspension is fully compressed or extended.
WARNING!
It is advisable to have an Öhlins dealer install
the steering damper. Always consult your vehicle service manual when installing this product.
Steering damper SD197
Stroke 63 mm
Recommended set-up:
10 clicks from closed.
SET-UP DATA
Page 3
Black cover
Nut
00430-02 (x2)
Bracket assembly
02230-01
Screw
05404-02
Steering
damper
SD197
Screw
05404-02
Fork leg
clamp bracket
02235-50
Frame bracket
02272-22
Spacer 02259-01
Screw
01046-17
HOW TO INSTALL
Screw
02274-02 (x2)
Page 4
© Öhlins Racing AB. All rights reserved.
Any reprinting or unauthorized use without the
written permission of Öhlins Racing AB
is prohibited. Printed in Sweden.
Mounting Instruction SD197_3.
Issued 2016-03-14
This instruction and other documents can be
downloaded from www.ohlins.com
Loading...