OFNA Racing Titan Deluxe RTR User Manual

INSTRUCTION MANUAL

PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL.

KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING.

REQUIRED FOR OPERATION

THINGS NEEDED

Glow Fuel

20%

AA Batteries ( 12 pcs )

#10212 NiHm Hump Pack, see charger 10214.

You will need to buy a few items to start the engine and run the car.

• Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will over heat engine.

• Buy LONG glow plugs, like OFNA/PICCO Plug (#51007). Use plugs without idle bar. Do NOT use plugs, like the MC-59 or OS-8

In your box you will find..

• #10163 - Bottle, spout top

• #10218 - Red “C” size glow heater

You need to get batteries for the radio transmitter and the car receiver packs.

• Radio TX needs (8) eight AA batteries.

• Car/Truck needs (4) four AA Ni-cad batteries, Alkaline type batteries will work, but braking will be reduced. The best is to use a 5 cell hump pack for increased voltage..

Recommended Option: You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 cell type(600AE). This will give more run time. OFNA #10212

10214 Over-nite Charger

TOOLS NOT INCLUDED IN KIT

Phillips Type Screw Drivers ( L )

Phillips Type Screw Drivers ( S )

Needle Nose Pliers

Knife

Cutter

Curved Scissors

Precision Caliper

Super Glue

Cross Wrench #17109 $3.95

Wheel Nut Wrench

INCLUDED WITH KIT

Shock Oil

Grease Box

7mm and 5.5mm Hex Wrench

5mm Hex Wrench

3mm Hex Wrench

2.5mm Hex Wrench

1.5mm Hex Wrench

MUST READ THIS BEFORE RUNNING

Running a nitro kit is fun and easy, but to make this a safe rusting. and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously injure someone if you are not careful.

Where to run car?

• Any running area you choose must be dry. Do not run car near any water or wet dirt.

• Do not run on public streets. It is very easy to have the car run over or damaged by hitting the curb.

• Do not operate car in tight confined places. The car is very fast and will easily hit something.

• Do not run near people or animals. and will too easily hit someone.

• Due noise, you will want to consider the surrounding area when operating the car.

• Do not operate the car at night. You will not be able to drive it without hitting something.

• Do not operate the car indoors. Engine exhaust is not healthy.

Glow Fuel

• Glow fuel is poisonous!

• Glow fuel is flammable!

• Do not leave in fuel bottle with lid off at any time. label for additional precautions.

• Do not use any fuel other than glow fuel in this engine.

First Time Starting the Engine

Caution! When starting engine make sure the following is observed. • Always turn off the car BEFORE turning off radio.

• Set engine Master needle to 3 turns (rich setting)

• Do not do this alone, get an experienced friend to help at • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY first. ISSUE.

• Fill fuel tank, try not to spill fuel. Do not spill fuel on receiver

• Hold car off the ground, so it will not runaway when first starts

• Turn on Radio and check the linkage before starting engine.

• Turn on car receiver battery switch.

• Always have an air filter on the carburetor to keep dirt out.

Engine Break-in

• See Engine Page.

The car is very fast

• Clean oil and dirt from chassis with a degreaser.

Precautions

• This kit is not a toy. Always run car with a second person as a spotter and pitman.

• Hot Parts - The pipe, manifold, engine and head are very hot and will cause burns.

• Rotating Parts - Keep hands away from the drive train, wheels, and engine when engine is running.

• Radio - Check batteries life before running the car. If radio does not have full control of the car with steering and/or throttle/brake do not run until corrected. Failure to correct this will result in possible injury and damage to the car or property.

• Glow fuel - Do leave the glow fuel unattended with the lid off. Fuel contains Methanol and Nitro Methane and is flammable and poisonous.

Store fuel in cool ventilated location. Refer the glow fuel

• Car Fuel tank - Never store fuel in car tank, it will ruin the engine if left in tank.

IF YOU DO NOT BREAK-IN ENGINE CORRECTLY, MAINLY AT LOW RPM, YOU WILL BREAK THE CONNECTING ROD!

FAILURE TO NOT READ AND FOLLOW BREAK-IN ENGINE

Emergency Stopping Engine When Running

• Remove air filter and cover carb. intake.

• Squeeze fuel line and hold until engine stops.

• With a rag, cover exhaust outlet.

Storing Car After Running

• Remove fuel from tank and fuel lines

• Turn off radio in car

• Put a few drops of after run in engine to keep it from

INSTRUCTIONS WILL VOID WARRANTY!

CHECK RADIO SETTING AND LINKAGE BEFORE STARTING

CHECKING ENGINE THROTTLE

1. Insert AA batteries into transmitter (8 Pcs).

2.Turn on transmitter.

3.Turn on receiver.

4.Center throttle trims as shown .

1. Pull Full Throttle.

1. Push trigger to full brake position.

2. Adjust alum. Stopper to increase or decrease the brake.

* Align throttle servo same as shown.

Brake (C)

Idle Position (A)

IMPORTANT CHECK RADIO THROTTLE AND STEERING SWITCHES BEFORE RUNNING CAR

* Insert into transmitter.

Note: Battery life is short when using Alkaline batteries. For safety, we recommend checking Alkaline batteries after 30 minutes. Battery strength affects radio range; in the case of a monster truck, it affects brake power. If voltage drops while running the car, you will loose control and destroy your car! This is NOT covered under warranty.

Full Throttle (B)

• Full throttle arm position. Spring rod pulls throttle barrel open and brake rods release pressure on brake cams.

• Full brake arm position. Spring compresses forward and brake rods pull brake levers.

To increase run time, upgrade receiver batteries to AA Ni-Cad or NiMH type. But, the most important step you can make, “is to always use fully charged or fresh batteries when running your car”.

The beat performance is achieved by changing to a 6 volt 5 cell hump pack, OFNA #10212. The servo have their greatest power at 6 volts.

Insert 8 pcs AA batteries into transmitter.

Radio shown may vary depending on availability. Therefore radio pictured on box may or may not be the same.

PLASTIC PARTS

40003 Diff. Case

40040 Center Diff Mount Tree

40017 Front and Rear Gear Boxes

36901 Front Knuckles, Pivot Ball

31304 Rear Hub, Pivot Ball

40056 Plastic Shock Parts Tree

40031 Servo Saver Plastic Tree

40203 Shock Tower part

40207 Bumper Mounts

40201 Front and Rear Upper Arms

40204 Chassis Skip Plate

40206 Chrome Roll Bar Plastic Parts(w/spot light)

40202 Front and Rear Lower Arms.

40205 Arm Holder/Center Diff. Mount /Side Chassis Brace Plastic Parts

ASSEMBLY OF THE DIFFERENTIAL

( Builds two differentials for front and rear.)

40006 Cap Joint

30701 4x4mm Set Screw

40010

2.5x13.8mm Pin

*Put the O-ring in inside of the diff. case and press it flush against the bottom.

40009 P6 O-Ring

40012 6x15mm Washer

40010

2.5x13.8mm Pin

40009 P6 O-Ring

36053 8x16mm Bearing

40006 Cap Joint

36053 8x16mm Bearing

Note: Diff must always use gear shim. If no shims are used, we have found that diff may break.

30779 4 x 10mm washer

Option: 49001 - Gears, HD Steel

40003 Diff. Case

30773 4mm Cross pin

40004

30779 4 x 10mm washer

30773 4mm Cross pin

Diff.Gear (Large)

40004 Diff. Gear (Small)

Note:

- Add grease into diff case before closing.

30779 4 x 10mm washer

40004 Diff.Gear (Large)

40012 6x15mm Washer

40214 Large Bevel Gear

40011 Diff. Gasket

40214 Large Bevel Gear

3x12mm Flat Head Tapping Screw

ASSEMBLY OF THE GEAR BOX ( Builds two gear box for front and rear.)

36053 8x16mm Bearing

49012

40017 Gear Box

13T Bevel Gear (l)Smal

36053 8x16mm Bearing

No need to add shims to this side. Loosening gear mesh will only cause gear to skip.

Note: ALWAYS USE OR ADD MORE! Adjust gear mesh by using #40024 shims. Add shim to either side for mesh. Recommend a

tight feel but not binding or loose. 40024 13x16x0.2mm Shim

40017 Gear Box

ASSEMBLY OF THE FRONT ARMS HOLDER

4X15MM Tapping Screw ( Small Head)

40242 Misc. Screws and Hardware

40022 Front Lower Arm Holder (Front/Alum.)

Option: 49002 CNC 7075 Front Lower Arm Holder

4X45MM Tapping Screw ( Small Head)

40015 Front Upper Arm Holder ( Rear/ Plastic)

40015

Front Lower Arm

Holder (Rear/Plastic)

40205 Upper Arm Holder

90026 5x5mm Set Screw

Screw Cement

36730 Cap Joint

4x16mm Flat Head Tapping Screw

4x15mm Screw (Small Head)

4x16mm Flat Head Tapping Screw

ASSEMBLY OF THE FRONT KNUCKLE ARMS

36905 Plastic Washer

36904 14mm Alum. Nut

Note: Thread nut into knuckle straight, do not cross thread. Do not over tight Nut. Adjust nut for smooth movement. If too tight, knuckle will not turn.

36903 14mm Steering Ball

( Left-Side )

36901 Ball Type Knuckle Arm

( Right- Side )

36901 Ball Type Knuckle Arm

36903 14mm Steering Ball

3x12mm Tapping Screw

36905 Plastic Washer

36904 14mm Alum. Nut

ASSEMBLY OF THE FRONT CVA JOINTs

36053 8x16mm Ball bearing

36052mm CVA Joint

36055

2.5x17mm Pin

Screw Cement

Spare: 15073 Nut, Hex Hub, Orange

5x5mm Set Screw

40245 Hex Hub, Orange

36053 8x16mm Ball bearing

36055

2.5x17mm Pin

36053 8x16mm Ball bearing

36054 8mm Alum. Wheel Hub

Screw Cement

90026 5x5mm Set Screw

36052 8mm CVA Joint

ASSEMBLY OF THE FRONT SUSPENSION ARM

90020

2.5mm E-Ring

90021 3mm E-Ring

40201 Upper Arm

40202 Lower Arm

* Insert the drive shaft into diff. cap joint before assembly.

40023 Lower Arm Shaft

40226 Upper Arm Shaft

90020

2.5mm E-Ring

90021 3mm E-Ring

40239 Servo Saver Post

40235 Lower Chassis

4X16mm Flat Head Screw

4x10mm Flat Head Screw

ASSEMBLY OF THE SERVO SAVER

40035 Alum. Servo Saver Tube

40031 Servo Saver Horn Plastic

40033 Servo Saver Spring

40034 Servo Saver Adjuster

ASSEMBLY OF THE SERVO SAVER UNIT

40037 Steering Plate Hex Screw

4x8mm Plastic Bushing

ASSEMBLY OF THE STEERING RODS

* Made two steering rods for left and right hand side.

36850 7mm Ball End

40031 Servo Saver Plastic Bushing

40032 Servo Saver Connecting Plate

49006 CNC Servo Saver Connecting Plate

36790 4x46mm Turnbuckle

40037 Steering Plate Hex Screw

4x8mm Plastic Bushing

* Take the 4x8mm Plastic Flange bushing and Plastic Bushing from servo saver plastic parts tree

40031 Servo Saver Plastic Bushing

36850 7mm Ball End

36700 Steering Ball End

ASSEMBLY OF THE SERVO SAVER AND STEERING RODS

3x15mm Screw

Option: 49014 Servo Saver Alum. Tube ( Ball bearing Type )

40039 3mm Cone Washer

35313 3mm Nylon Nut

ASSEMBLY OF THE SERVO SAVER ONTO LOWER CHASSIS

3x12mm Flat Head Screw

* Place the servo saver into the servo post.

3x12mm Flat Head Screw

35313 3mm Nylon Nut

ASSEMBLY OF THE REAR UPPER ARM

*Builds two arms for left and right hand side.

Assembly of the right and left hand side are the same.

36850 7mm Ball

ASSEMBLY OF THE REAR HUB

*Builds two hubs for left and right hand side.

31304 Rear Hub ( Ball Type )

36690 7mm Plastic Ball End

Note: This Axles part is not needed if your kit has CVA joint for rear instead.

36860 5x35mm Turnbuckle

31307 11mm Ball & Screw

36081 8mm Rear Wheel Axle

31305 Plastic Washer

36053 8x16mm Ball bearing

40201 Upper Arm

31306 12mm Alum. Hex Screw

36053 8x16mm Ball bearing

8mm

Assembly of the right and left hand side are the same.

36055

2.5x16.8mm Pin

20245 Wheel Hub, Orange

Screw Cement

ASSEMBLY OF THE REAR HUB AND SUSPENSION ARMS INTO GEAR BOX

35313 M3 Nylon Nut

90021 3mm E-Ring

30702 3x25 Hex Screw

90020

2.5mm E-Ring

40215 Rear Drive Shaft (91.5mm)

Upper Arm Washer

40202 Rear Lower Arm

40023 4mm Lower Arm Shaft

Assembly of the right and left hand side are the same.

90020

2.5mm E-Ring

90021

3mm E-Ring

*Insert the rear drive shaft before assembly the rear lower arm.

40215 Rear Drive Shaft (91.5mm)

90026 5x5mm Set Screw

ASSEMBLY OF THE FRONT GEAR BOX ONTO UPPER CHASSIS

4x10mm Flat Head Screw

4X16mm Flat Head Tapping Screw

4x15mm Screw

35314 M4 Nylon Nut

4x15mm Screw

40234 Main Chassis

40205 Center Diff. Mount

35314 M4 Nylon Nut

ASSEMBLY OF THE FRONT SHOCK TOWER

40203 Shock Tower

3x16mm Tapping Screw

4x25mm Screw

4x16mm Tapping Screw

40040 Center Brace Mount ( Front )

35314 M4 Nylon Nut

+ 23 hidden pages