Ocean Optics INLINE-TTL-S User Manual

Page 1
Inline TTL Shutter
INLINE-TTL-S
Installation and Operation Manual
Offices: Ocean Optics, Inc. World Headquarters
830 Douglas Ave., Dunedin, FL, USA 34698
Phone 727.733.2447 Fax 727.733.3962
8 a.m.– 6 p.m. (Mon-Fri), ET
Ocean Optics Mikropack
Maybachstraße 11, D73760, Ostfildern, Germany
Phone +49 (0)711 34 16 96-0 Fax +49 (0)711 34 16 96-85
E-mail: Info@OceanOptics.com (General sal es inq u iri e s)
Info@OceanOpticsBV.com (European sales inquiries) Orders@OceanOptics.com (Questions about orders) TechSupport@OceanOptics.com (Technical support)
000-00000-000-02-A
Page 2
Copyright © 2009 Ocean Optics, Inc.
All rights reserved. No part of this publication may be reproduced, stored i n a re trie val system, or transmitted, by any means, electronic, mechanical, photocopyin g, r ec ord ing, or otherwise, without written perm ission from Ocean Optics, Inc. This manual is sold as part of an order and subject to the condition that it shall not, by way of trade or otherwise, be lent, re-sold, hired out or otherwise circulated with out the pr ior consent of Ocean Optics, Inc. in any form of bin di ng or cover other than that in which it is published.
Trademarks
Microsoft, Windows, Wind ow s 95, Windows 98, Windows Me, Windows N T, Windows 2000, Windows XP and Ex cel are either registered trademarks or t ra d emarks of Mi c r osoft Cor p oration.
Limit of Liability
Every effort has been m ade to make this manual as complete an d as accurate as possible, but no warrant y or fitness is implied. T h e in formation provided is on an “as is” basis. Ocean O ptics, Inc. shall have neither liability nor responsib ility to any person or entity wit h r es p e c t t o any loss or damages arising from the inform a t i on contained in this manual
Page 3
Table of Contents
About This Manual .............................................................................................................iii
Document Purpose and Intended Audience .............................................................................. iii
What’s New in this Document ................................................................................................... iii
Document Summary .................................................................................................................. iii
Product-Related Documentation ............................................................................................... iii
Upgrades ............................................................................................................................iii
Chapter 1: Setup ................................................................................... 1
Overview .............................................................................................................................1
Unpacking ...........................................................................................................................2
Contents .............................................................................................................................2
Chapter 2: INLINE-TTL-S Specifications............................................ 3
Operating Environment ......................................................................................................3
Specifications .....................................................................................................................3
Pinout Information ..............................................................................................................4
Pinout Diagram .......................................................................................................................... 4
Transmission ......................................................................................................................5
Mechanical Diagrams .........................................................................................................6
Index ...................................................................................................... 8
000-10000-090-02-201401 i
Page 4
Table of Contents
ii 000-10000-090-02-201401
Page 5

About This Manual

Document Purpose and Intended Audi ence

This document provides you with an installation section to get your system up and running.

What’s New in this Document

This version of th e In line TTL Shutter Inline-TTL-S Installation and Operation Manual adds mechanical diagrams.

Document Summary

Chapter Description
Chapter 1: Setup
Chapter 2: INLINE-TTL-S Spec if icati ons
Contains instructions for setting up your Inline TTL Shutter.
Contains operating specifications and pinout information.

Product-Related Documentation

You can access documentation for Ocean Optics products by visiting our website at
http://www.oceanoptics.com. Select Technical → Operating Instructions, then choose the appropriate
document from the available drop-down lists. Or, use the Search by Model Number field at the bot t om of the web page.
You can also access operating instructions for Ocean Optics products on the Software and Technical Resources CD included with the system.
Engineering-level documentation is located on our website at Technical → Engineering Docs.

Upgrades

Occasionally, you may find that you need Ocean Optics to make a change or an upgrade to your system. To facilitate these changes, you must first contact Customer Support and obtain a Return Merchandise Authorization (RMA) number. Please contac t an Ocean Optics for specific instructions when returning a product.
000-10000-090-02-201401 iii
Page 6
About This Manual
iv 000-10000-090-02-201401
Page 7
Chapter 1

Setup

Overview

INLINE-TTL-S Inline TTL Shutter is a small mech anical laser-cut shutter that is positioned between two UV/VIS-optical components. The INLINE-TTL-S is an OEM part for use in other equipment.
The shutter is controlled by a small circuit board that is powered by a 12 VDC signal. The maximu m frequency at whi ch the IN LIN E -TTL-S can operate is 5Hz (5 shutter cycles per second).
Inline TTL Shutter (15-pin input component and control circuitry not shown)
Inline TTL Shutter (bottom) with 15-pin input component and control circuitry (top)
000-10000-090-02-201401 1
Page 8
1: Setup

Unpacking

Procedure
1. Unpack your lamp assembly carefully. Although the deuterium lamp is rigidly mounted, dropping
this instrument can cause permanent damage.
2. Inspect the outsid e of the instru m ent and make sure that there is no damage. Do not use the
instrument if damage is present. Contact your dealer for repair or replacement information, if necessary.
3. Use this instrument in a clean laboratory environment (see Operating Environment
).

Contents

Your package should contain the following:
Inline-TTL-S Inline TTL Shutter One IC -DB15-2 interface cable for shut te r ope rati on
Additionally, you will need an approved power supply for the LS-475, such as th e Mikropack PS­12V/1.25A power supply.
Procedure
To set up your Inline TTL Shutter review the figures on the previous page and perform the following
procedure:
1. Plug in the power supply.
2. Plug the power supply connector into the INLINE-TTL-S sleeve.
3. Remove the SMA connector caps.
4. Connect the SMA connectors on your fibers to the SMA plugs on each end of the INLINE-TTL-S
shutter.
5. Plug the SUB-D 15-pol. connector into the sleeve for automatic TTL operation (cable included).
You have now configured the INLINE-TTL-S for use.
2 000-10000-090-02-201401
Page 9
Chapter 2

INLINE-TTL-S Specifications

This secti on provides information on the operating environment and physical specifications of the INLINE-TTL-S. It also provides pinou ts f or the 15 -p in connector.

Operating Environment

The following table provides information on optimizing the operating environment of your INLINE-TTL­S.
Operating Environment The INLINE-TTL-S Unit . . .
Moisture Is designed for operation in dry rooms only. Ventilation Should be situated so that its location or position does not interfere with
proper ventilation. Heat Should be situated away from any device that emits excessive heat. Object and Liquid Entry Should be positioned so that objects do not fall on top of the unit.
Additionally, ensure that no liquids are spilled into the enclosure through
openings. Power Sources Should be connected to an approved power supply, such as the Mikropack
12 VDC 1250mA analog regulated power supply (PS-12V/1.25A)

Specifications

Specifications Criteria
Spectral Range UV-VIS Shutter Input TTL maximum 5 Hz Power Requirements 12 VDC Power Consumption Maximum 100 mA Weight Approximately 600 g Size 140 x 50 x 50 mm
000-10000-090-02-201401 3
Page 10
2: INLINE-TTL-S Specifications

Pinout Information

The following table contains pinout information for the INL INE-TTL-S:
Pin Description
1 na 2 na 3 na 4 na 5 na 6 na 7 na 8 na 9 na 10 Ground 11 na 12 na 13 TTL Signal 14 na 15 na na = not applicable

Pinout Diagram

4 000-10000-090-02-201401
Page 11
2: INLINE-TTL-S Specifications

Transmission

000-00000-000-02-201401 5
Page 12
2: INLINE-TTL-S Specifications

Mechanical Diagrams

Front View -- Mounting Point on Front Plate (dimensions in mm)
6 000-10000-090-02-201401
Page 13
2: INLINE-TTL-S Specifications
Bottom View -- Mounting Point on Base Plate (dimensions in mm)
000-00000-000-02-201401 7
Page 14
Index
D
document
audience, iii purpose, iii summary, ii i
M
mechanical diagrams, 6
O
operating environment, 3
P
package contents, 2 pinouts, 4 product-related documentation, iii
S
setup, 1 specifications, 3
T
transmission, 5
U
unpacking procedure, 2 upgrades, iii
W
what's new, iii
000-10000-090-02-201401 8
Page 15
2: INLINE-TTL-S Specifications
000-00000-000-02-201401 9
Loading...