Oasis POU1RRHS, POU1RRK Owner’s Manual

OASIS® WATER COOLER MODELS

POU1RRK, POU1RRHS, POU1SRK, POU1SRHS INSTRUCTIONS

A. INSPECTION

Inspect the carton and water cooler for evidence of rough handling and concealed damage. Damage claims should be filed with the carrier.

B. MAINTENANCE

1. Inspect the condenser for dirt and lint every three months. If cleaning is required, disconnect the power supply cord, then clean the condenser with a small

stiff non-wire brush. Observance of this procedure will ensure adequate air circulation through the condenser for efficient and economical operation.

2. A cone shaped strainer can be found in the tube leading into the mechanical float valve on the reservoir cap. It can be removed and flushed clean. Be sure to

C. OVERLOAD PROTECTION

The compressor motor is equipped with an automatic reset protector which will disconnect the motor from the line in case of an overload.

D. LUBRICATION

This unit is equipped with a hermetically sealed compressor which does not require any additional lubrication.

E. TO PUT WATER COOLER INTO SERVICE

F. SAFETY FLOAT

The cooler is equipped with a safety float to prevent overfilling in case the fill float fails. If the fill float should fail, the safety float will be activated as the

G. TO DISCONTINUE USE OF WATER COOLER

H. REMOVABLE RESERVOIR

1. To Remove Reservoir

2. Installing New Reservoir

J. ALTERNATE FAUCETS

A safer faucet that deters accidental dispensing of water by toddlers is available. This new faucet is simple and easy to use with one hand yet it adds a new measure of protection to your water cooler. See your dealer for details.

The warranty for this machine is automatically void if any alteration, modification, or combination with any other machine or device is deemed to be the source of any claim. The Underwriters’ Laboratory Listing and CSA’s Certification may be void as the result of any alteration or modification. The manufacturer accepts no liability resulting from any alteration, modification, or combination with any other machine or device.

EXCEPT AS SET FORTH HEREIN, THE MANUFACTURER MAKES NO OTHER WARRANTY, GUARANTEE OR AGREEMENT EXPRESSED, IMPLIED OR STATUTORY, INCLUDING ANY IMPLIED WARRANTY OR MERCHANTIABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

replace it in the tube once cleaned.

1. The water cooler should be located a minimum of 2" (51mm) from the wall to assure adequate condenser air circulation.

2. If filter(s) are to be added, follow filter manufacturer’s recommended instructions.

3. Remove blue plug from “inlet” fitting on the back of the cooler. Push a ¼” OD copper tube into the fitting. Connect to cold water supply.

4. WARNING: A pressure regulator, such as a Slow Flow regulator, must

any possible pressure spikes) could exceed 100psig (690kpg).

5. Turn on water supply to cooler.

6. Check the available power supply against the water cooler data plate to assure correct electrical service. Plug power supply cord into receptacle

7. CAUTION: On models with a hot tank, the hot tank switch must be in the “OFF” position. Switch is mounted at the rear of the cooler on the

condenser.

8. After the reservoir is full, check all connections for leaks.

9. Open each faucet until water flows freely.

10. On models with a hot tank, turn on the hot tank by depressing the switch toward the “RESET” position.

11. CAUTION: Failure to fill hot tank with water before turning on the hot tank can cause physical damage to the unit.

12. CAUTION: WATER FROM HOT FAUCET CAN SCALD.

water level rises. When the safety float is activated, water flow to the reservoir will be shut off. Press the blue reset button about half way down on the reservoir cap until you hear the water flow restart, then call your service representative. CAUTION: A hard impact or jarring of the unit while it is filling may trip the safety float.

1. On models with a hot tank, place hot tank switch in the “OFF” position. Draw water from hot faucet until water is cool.

2. Disconnect power supply cord.

3. Shut off water supply to cooler.

4. Drain reservoir through cold faucet.

5. On models with a hot tank, drain tank by placing a container under black drain valve located on the condenser. Turn drain valve counter clockwise to open,

and catch water in container. OR, for convenience, insert one end of a 3/8” OD tube into the opening of the drain valve and the other into a container and drain. Close drain valve when the tank is empty.

6. ALWAYS DRAIN ALL WATER WHEN FREEZING TEMPERATURES ARE ANTICIPATED OR BEFORE SHIPPING THE WATER COOLER.

a) Drain the cooler as described in Section G. b) Rem ove top by lifting it up from the rear. c) Remove float cap assembly by lifting it up and out of the reservoir. d) There may be an ice bank formed around the cooling probe. Pour warm water over the ice to melt it away from the probe.

Remove the faucets from the reservoir by unscrewing them in a counterclockwise fashion.

e) f) Grasp the top of the reservoir around the opening and pull upward in a straight motion.

a) Align reservoir with probe. Press reservoir downward touching only the outer rim.

DO NOT TOUCH THE INSIDE OF THE RESERVOIR WITH BARE HANDS, IT MUST REMAIN SANITARY.

b) Reattach the faucets to the reservoir, making sure that the gaskets are in place.

WARNING

be installed in front of the unit’s water inlet if the water pressure (including

030099-216 Rev D

222 East Campus View Blvd. • Columbus, OH 43235 U.S.A.

1-800-950-3226

www.oasiscoolers.com

is a registered trademar k of Oasis International 030099-216 Re v D

OASIS