NUUO 6000S, 7000S, 6008S, 6004S, 7016S Installation Manual

The Intelligent Surveillance Solution

Hardware & Software NDVR

Installation Guide

Ver. 5.1

Int elligent Surveillance Solution

Table of Contents

TTAABBLLEE OOFF CCOONNTTEENNTTSS

TABLE OF CONT ENTS ...................................................................................................... 1

6000S/7000S SERIES ........................................................................................................ 2

Product Specification ............................................................................................... 2

System Requirement ................................................................................................. 2

Hardware Installation................................................................................................ 4

Maximum I/O Cards support for 6000S/7000S ................................................... 6

7100 SERIES ....................................................................................................................... 7

Product Specification ............................................................................................... 7

System Requirement ................................................................................................. 7

Hardware I nstallat ion................................................................................................ 8

8000HD SERIES ...............................................................................................................10

Product Specification .............................................................................................10

System Requirement ...............................................................................................10

Hardware Installation..............................................................................................11

DRIVER I NSTALLATION..................................................................................................13

SOFTWARE I NSTALLATION ...........................................................................................15

SOFTWARE I NSTALLATION – EXPRESS MODE..........................................................21

SOFTWARE I NSTALLATION – FAILOVER AGENT ( STANDARD MODE) ...............24

SOFTWARE I NSTALLATION – FAILOVER AGENT ( EXPRESS MODE).....................29

APPENDIX - MINIMUM HARDWARE REQUIREMENT ..............................................33

page - 1

Int elligent Surveillance Solution

Model

6016S

6008S

6004S

Display Rat e

480fps(NTSC);

400fps (PAL)

240fps(NTSC);

200fps (PAL)

120fps(NTSC);

100fps (PAL)

Recording Rate

(CIF)

480fps(NTSC);

400fps (PAL)

240fps(NTSC);

200fps (PAL)

120fps(NTSC);

100fps (PAL)

Maximum Card

4 4 4

Video Input

16 8 4

Audio Input

16 8 4

Video Resolution

NTSC: 176x120; 352x240; 704x480

PAL: 176x144; 352x288; 704x576

Compression Format

Hardware Compression H.264

7016S

7008S

7004S

Display Rat e

480fps(NTSC);

400fps (PAL)

240fps(NTSC);

200fps (PAL)

120fps(NTSC);

100fps (PAL)

Recording Rate (D1)

480fps(NTSC);

400fps (PAL)

240fps(NTSC);

200fps (PAL)

120fps(NTSC);

100fps (PAL)

Maximum Card

4 4 4

Video Input

16 8 4

Audio Input

16 8 4

Video Resolution

NTSC: 176x120; 352x240; 704x480

PAL: 176x144; 352x288; 704x576

Compression Format

Hardware Compression H.264

66000000SS//77000000SS SSEERRIIEESS

Product Specification

System Requirement

The system requirement depends on t he number of camera connections
and the t otal bit rate of the IP cameras. Please refer Appendix - Minimum

Hardware Requirement or check NUUO Calculator on
htt p://support.nuuo.com/calculator/

page - 2

Int elligent Surveillance Solution

Hardware Installation

 The electronic components within the unit are sensitive to

damage from Electro-Static Discharge (ESD). Please t ake
precautions at all times when handling the unit or its
sub-assemblies.

 Proper Surge solut ion is needed for outdoor application. It

provides protection from damaging transient voltage surges and
spikes.

Caution

page - 3

Int elligent Surveillance Solution

Hardware Installation

Step1: Insert t he card onto an empty PCI-e slot. Connect the Audio/Video

Cable to t he connector.
Note 1: The audio input connectors are with red wires and marked of “A”

on them (such as “A1/9”); the video input connectors are with black wires
and marked of “V” (such as “V8/16”).

Note 2: You need t o power down the PC before you insert t he card.

Step 2: Connect the Watchdog wire t o t he reset connector on the main

board.
Note: With the Watchdog Wire connected, the system will be restarted if
any abnormal conditions.

Step 3: Turn on your PC and start Windows.

Step 3: I nsert the included Software CD into CD-ROM.

Step 4: Refer t he section Driver Installation on page 18 to install driver.

Step 5: Aft er driver is installed, restart your PC.

Optional I/O Card: refer to the figures on the following pages.

Step 1: Fix the I O card onto your PC.

Step 2: Connect the Capture Card and the I/O Card with an included

ribbon cable (2.00mm IDC cable).
Note 1: The default configuration of blue slide swit ch on I/O Card as

below.
Note 2: If you only use one I/O card to connect with one of 6000S/7000S
cards, please make sure t he configurat ion of the black slide switch as
below.

Maximum optional I/O Card support:

6000S/7000S can support maximum 4 I/O cards. Please refer to figures on
the following pages.

page - 4

Int elligent Surveillance Solution

Connect to IO board
(2.00mm IDC cable)

6000S/7000S Series Capture Card

I/O card

Note: Please do not connect 2 capture cards in one IO board at t he same

time.

page - 5

Int elligent Surveillance Solution

Maximum I/O Cards support for 6000S/7000S

Note: If you use more t han one IO card, please make sure t he

configurat ion of each black switch as above.

page - 6

Int elligent Surveillance Solution

7116

7108

Display Rat e

480fps(NTSC);

400fps (PAL)

240fps(NTSC);

200fps (PAL)

Recording Rate (D1)

480fps(NTSC);

400fps (PAL)

240fps(NTSC);

200fps (PAL)

Maximum Card

1

1

Video Input

16

8

Audio Input

16

8

Video Resolution

NTSC: 176x120; 352x240; 704x480

PAL: 176x144; 352x288; 704x576

TV Output Rate

w/ HDMI : RCA & HDMI: 10fps

w/o HDMI: RCA: 25fps

Only HDMI: HDMI: 14fps

Compression Format

Hardware Compression H.264

77110000 SSEERRIIEESS

Product Specification

System Requirement

The system requirement is depend on the number of camera connections
and the t otal bit rate of the IP cameras. Please refer Appendix - Minimum

Hardware Requirement or check NUUO Calculator on
htt p://support.nuuo.com/calculator/

 The electronic components within the unit are sensitive to

 Proper Surge solut ion is needed for outdoor application. It

Caution

damage from Electro-Static Discharge (ESD). Please t ake
precautions at all times when handling the unit or its
sub-assemblies.

provides protection from damaging transient voltage surges and
spikes.

page -7

Int elligent Surveillance Solution

Hardware Installation

Step1: Insert t he card onto an empty PCI-e slot. Connect the Audio/Video

Cable to t he connector.
Note 1: The audio input connectors are with red wires and marked of “A”

on them (such as “A1/9”); the video input connectors are with black wires
and marked of “V” (such as “V8/16”).

Note 2: You need t o power down the PC before you insert the card.

Step 2: Connect the Watchdog wire t o t he reset connector on the main

board.
Note: With the Watchdog Wire connected, the system will be restarted if
any abnormal conditions.

Step 3: Turn on your PC and start Windows.

Step 3: I nsert the included Software CD into CD-ROM.

Step 4: Refer t he section Driver Installation on page 18 to install driver.

Step 5: Aft er driver is installed, restart your PC.

Optional I/O Card: refer to the figures on the following pages.

Step 1: Fix the I O card onto your PC.

Step 2: Connect the Capture Card and the I/O Card with an included

ribbon cable (2.54mm I DC cable).
Note 1: The default configuration of blue slide swit ch on I/O Card as

below.

Note 2: Before inst all SCB-7100 Series cards, please connect HDMI cable
first then it would be easier t o fix the card onto the PCI -e slot.

Note 3: Some chassis may not be suitable for inst alling SCB-7100 series due
to t he original design, please check t he dimension of the chassis before
installing.

page - 8

Int elligent Surveillance Solution

7100 Series Capture Card

I/O card

Maximum I/O Cards support for 7116

Please refer to page 5 Maximum I/O Cards support for G3-3016

page - 9

Int elligent Surveillance Solution

8004HD

Display Rat e

120fps(NTSC);

100fps(PAL)

Recording Rate

1080P@120(NTSC)

1080P@100(PAL)

Maximum Card

4

Video Input

4

Audio Input

0

Video Resolution

1080P30/25

720P60/50/30/25

Compression Format

Hardware Compression H.264

88000000HHDD SSEERRIIEESS

Product Specification

System Requirement

The system requirement is depend on the number of camera connections
and the t otal bit rate of the IP cameras. Please refer Appendix - Minimum

Hardware Requirement or check NUUO Calculator on
htt p://support.nuuo.com/calculator/

 The electronic components within the unit are sensitive to

 Proper Surge solut ion is needed for outdoor application. It

Caution

damage from Electro-Static Discharge (ESD). Please t ake
precautions at all times when handling the unit or its
sub-assemblies.

provides protection from damaging transient voltage surges and
spikes.

page - 10

Int elligent Surveillance Solution

Hardware Installation

Step1: Insert t he card onto an empty PCI-e slot. Connect the BNC Cable

(not in product content) to t he connector.

Note: You need to power down the PC before you insert the card.

Step 2: Connect the Watchdog wire to the reset connector on the main

board.
Note: With the Watchdog Wire connected, the system will be restarted if
any abnormal conditions.

Step 3: Turn on your PC and start Windows.

Step 3: I nsert the included Software CD into CD-ROM.

Step 4: Refer t he section Driver Installation on page 18 to install driver.

Step 5: Aft er driver is installed, restart your PC.

Optional I/O Card: refer to the figures on the following pages.

Step 1: Fix the I O card onto your PC.

Step 2: Connect the Capture Card and the I/O Card with an included

ribbon cable (2.00mm I DC cable).
Note 1: The default configurat ion of blue slide swit ch on I/O Card as

below.
Note 2: If you only use one I /O card to connect wit h an 8004HD card,
please make sure the configuration of the black slide switch as below.

Maximum optional I/O Card support:

Please refer to page 11 Maximum I/O Cards support for 6000S/7000S

page -11

Int elligent Surveillance Solution

8004HD Card

Note: The default configuration of the black swit ch on 8004HD card is as

above. Do not adjust it .

I/O card

page - 12

Int elligent Surveillance Solution

DDRRIIVVEERR IINNSSTTAALLLLAATTIIOONN

Step 1: Insert t he I nstallation CD. Run autostartup.exe from the

CD-ROM directly to start the installation.

Step 2: Select “DVR Driver Inst allation” then click on it.

Step 3: In the NUUODriver Set up Wizard dialog box, click Next to

continuous.

Step 4: Check the “License agreement”. Click “I Agree” t o continuous.

page - 13

Int elligent Surveillance Solution

Step 5: Inst alling NUUODriver.

Step 6: Click “Finish” after installing t he system completely, and then

choose t o reboot now or lat er.

page - 14

Int elligent Surveillance Solution

SSOOFFTTWWAARREE IINNSSTTAALLLLAATTIIOONN

Step 1: Insert t he I nstallation CD. Run Autorun Tool from the CD-ROM

directly to start the installation.

Step 2: Select “Server Application Installation” then click on it.

Step 3: In the InstallShield Wizard dialog box, select language and click

Next to continuous.

Step 4: There are 2 Installation Mode of options in “Init iation Mode”

window, select one and click Next to st art t he installshield of Server
package.

page -15

Int elligent Surveillance Solution

Step 3: There are 4 system t ypes of options in “System Setup Tool” window,

select one and click Next to st art t he inst allshield of Server
package.

- NUUO IP Surveillance System/Trial System

- NUUO MPEG-4 Hybrid System

- NUUO Full HD/D1 H.264 Hybrid System

Not e: The Setup Tool will det ect the type of capture cards installs

on PC and enable the options of system types automatically.

page - 16

Int elligent Surveillance Solution

Step 4: In the InstallShield Wizard dialog box, click Next to continuous.

Step 5: Check the option “I accept the t erms of the license agreement”.

Click Next t o continuous.

Step 6: Please enter your name and the company name for which you

work. Click Next to continuous.

page - 17

Int elligent Surveillance Solution

Step 7: Select “Complete Setup Type” or “Custom Setup Type” to inst all the

System.

COMPLETE SETUP TYPE

Inst all all program features into t he default directory.

- Check the option “Complete”, and then click “Next”. All

program features will be installed. [Require the most disk
space.]

CUSTOM SETUP TYPE

Inst all the system to a preferred directory. Or select whichever
program feature(s) t o install. This is recommended for advanced
users.

- Check the option “Custom”, and t hen click “Next”.

- Select appointed folder where setup will install files to. Click

“Change” t o modify the inst allation directory.

page - 18

Int elligent Surveillance Solution

- Select the feat ures set up will install. There are 4 features to

choose in the server set up process: MainConsole, Playback,

LiveView, Backup, and Verification tool. Click “Next” aft er

confirmation.

Step 8: Click install to start the installation.

Step 9: Click Finish after installing the system completely.

page - 19

Int elligent Surveillance Solution

Step 10: Execute the Main Console

Step 11: Ent er t he password you like into t he edit box and enter again at

the edit of Password Confirm. And then press “OK”. Now enjoy our
Int elligent Surveillance Solution.

page - 20

Int elligent Surveillance Solution

SSOOFFTTWWAARREE IINNSSTTAALLLLAATTIIOONN –– EEXXPPRREESSSS MMOODDEE

Step 1: Insert t he I nstallation CD. Run Autorun Tool from the CD-ROM

directly to start the installation.

Step 2: Select “Server Application I nstallation” then click on it.

Step 3: There are 4 syst em t ypes of options in “System Setup Tool” window,

select one and click Next to st art t he inst allshield of Server
package.

- NUUO IP Surveillance System/Trial System

- NUUO MPEG-4 Hybrid System

- NUUO Full HD/D1 H.264 Hybrid System

Not e: The Setup Tool will det ect the type of capture cards installs

on PC and enable the options of system types automatically.

page - 21

Int elligent Surveillance Solution

Step 4: In the InstallShield Wizard dialog box, select language and click

Next to continuous.

Step 5: There are 2 Installation Mode of options in “Init iation Mode”

window, select one and click Next to st art t he installshield of Server
package.

Step 6: Click install to start the installation.

page - 22

Int elligent Surveillance Solution

Step 7: Click Finish after installing the system completely.

Step 8: Execute the Main Console

Step 9: Ent er t he password you like into t he edit box and enter again at the

edit of Password Confirm. And then press “OK”. Now enjoy our Intelligent

Surveillance Solution.

page - 23

Int elligent Surveillance Solution

SSOOFFTTWWAARREE IINNSSTTAALLLLAATTIIOONN –– FFAAIILLOOVVEERR AAGGEENNTT ((SSTTAANNDDAARRDD MMOODDEE))

Step 1: Insert t he I nstallation CD. Run Autorun Tool from the CD-ROM

directly to start the installation.

Step 2: Select “Failover Agent I nstallation” then click on it.

Step 3: In the InstallShield Wizard dialog box, select language and click

Next to continuous.

Step 4: There are 2 Installation Mode of options in “Init iation Mode”

window, select one and click Next to st art t he installshield of Server
package.

page - 24

Int elligent Surveillance Solution

Step 5: In the InstallShield Wizard dialog box, click Next to continuous.

Step 6: Check the option “I accept the t erms of the license agreement”.

Click Next t o continuous.

Step 7: Please enter your name and the company name for which you

work. Click Next to continuous.

page - 25

Int elligent Surveillance Solution

Step 8: Select “Complete Setup Type” or “Custom Setup Type” to inst all the

System.

COMPLETE SETUP TYPE

Inst all all program feat ures into t he default directory.

- Check the option “Complete”, and then click “Next”. All

program features will be installed. [Require the most disk
space.]

CUSTOM SETUP TYPE

Inst all the system to a preferred directory. Or select whichever
program feature(s) t o install. This is recommended for adv anced
users.

- Check the option “Custom”, and t hen click “Next”.

- Select appointed folder where setup will install files to. Click

“Change” t o modify the inst allation directory.

page - 26

Int elligent Surveillance Solution

- Select the feat ures set up will install. Click “Next” aft er

confirmation.

Step 8: Click install to start the installation.

Step 9: Click Finish after installing the system completely.

page - 27

Int elligent Surveillance Solution

Step 10: Execute the Failover Agent

Step 9: Ent er t he password you like into t he edit box and enter again at the

edit of Password Confirm. And then press “OK”. Now enjoy our Failover
Agent service.

page - 28

Int elligent Surveillance Solution

SSOOFFTTWWAARREE IINNSSTTAALLLLAATTIIOONN –– FFAAIILLOOVVEERR AAGGEENNTT ((EEXXPPRREESSSS MMOODDEE))

Step 1: Insert t he I nstallation CD. Run Autorun Tool from the CD-ROM

directly to start the installation.

Step 2: Select “Failover Agent I nstallation” then click on it.

Step 3: In the InstallShield Wizard dialog box, select language and click

Next to continuous.

Step 4: There are 2 Installation Mode of options in “Init iation Mode”

window, select one and click Next to st art t he installshield of Server
package.

page - 29

Int elligent Surveillance Solution

Step 5: Click install to start the installation.

Step 6: Click Finish after installing the system completely.

Step 7: Execute the Failover Agent

Step 8: Ent er t he password you like into t he edit box and enter again at the

edit of Password Confirm. And then press “OK”. Now enjoy our Failover
Agent service.

page - 30

Int elligent Surveillance Solution

Note: When use Windows 8, please disable Metro function first before st art

Mainconsole. For furt her st eps, please refer t o:

htt p://www.youtube.com/watch?v=xERxpbwBt0U

Note: When use Windows Server 2012, please enable desktop experience

first before start Mainconsole. For furt her steps, please refer t o:

htt p://social.technet.microsoft.com/wiki/contents/articles/10531.windows

-server-8-beta-how-to-enable-desktop-experience-feature-en-us.aspx

the Desktop Experience feature in Windows Server 8 Bet a belongs t o User
Interfaces and Infrastructure feature. In order t o install Desktop Experience
feature, do t he following steps:

Open Server Manager > Manage > Add Roles and Features.

Before you begin to install a feature, you can read information in
the Before you begin page. This page is very useful for anyone who has
start ed learning Windows Server 8. Select Skip this page by default in order
to remove this page for the next times you add roles or features.

In the Select installation type page, you have t wo options:

1. Role-based or feature-based installation: this option t hat similar t o t he

one available in the Windows Server 2008 is used when you want to
add roles, features in single server.

2. Remote Desktop Services scenario-based installation t his option allows

you t o install, configure and manage RS session Host servers from a
central location.

In the Select destination server page, select the server pool under SERVER
POOL. With flexible server platform, now you can select a virtual hard disk

page - 31

Int elligent Surveillance Solution

as a destination server when deployed roles or features.

Skip the Select server roles page. I n the Select features page, you can
select User Int erfaces and infrastruct ure feat ure. You will be prompted to
install t he required components or services “Ink and Handwriting Services”
and “Media Foundation”. Click Add Features.

In the Confirm installation selections page, select Restart the destination
server automatically if required. You must restart computer after installing
completely.

You have another way to add feature by using Powershell:
Add-WindowsFeature Desktop-Experience.

page - 32

Int elligent Surveillance Solution

AAPPPPEENNDDIIXX -- MMIINNIIMMUUMM HHAARRDDWWAARREE RREEQQUUIIRREEMMEENNTT

Please refer NUUO online Design Tool for sever spec evaluation:

http://w w w.nuuo.com/calculator/

page -33