Industrial Paddle Fan
MODELS: PFC-48II & PFC-56II /SERIES
CAUTIONS
WARNING: To reduce the risk of personal injury, do not bend the
blade brackets when installing the brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between rotating
fan blades.
WARNING: To reduce the risk of fire, electric shock, or personal
injury, mount to outlet box marked “Acceptable for Fan Support” and
use mounting hardware provided with the box.
WARNING: To reduce the risk of fire, electric shock, do not use this
fan with any solid-state speed control device.
This product must be mounted and wired in compliance with all local
and national electrical codes.
Before wiring the ceiling fan, turn off electric power at the circuit
breaker or fuse box and leave off until installation is complete.
Mount outlet box so that it will support at least 35 pounds.
Note: the weight of the fan is as follows:
PFC-48 14 lbs. PFC-56 20 lbs.
LOCATION
1. When fan is installed, you must allow a minimum of 10 feet between floor and bottom of fan blades.
2.For this model, the center of the fan must be located at least 32”
from any vertical surface - wall, doors, partitions, etc. This allows
minimum clearance for fan blades.
3.Do not mount fan below, next to or between air ducts, beams or
any other obstructions which may interfere with the natural air flow
pattern created by the fan.
4. Place fans near constantly opening doors and shipping bays to
produce an “air shield” effect that helps keep out cold air in winter
and dust, odors and insects in the summer.
5. If desired, fans can be installed directly above heat producing
machinery to reclaim the heated air.
6. For maximum air flow, fans should be located above aisles in
warehouses and storage areas.
7.Make sure fan voltage is compatible with your electrical system.
8.FOR SLOPED CEILING INSTALLATIONS ONLY: Ball and socket
mounting system will work on sloped ceilings up to 22° maximum
(rise/run = 5/12).
INSTALLATION INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
Photo shows
hardware included
with your new
ceiling fan.
MOUNTING
BRACKET
DOWN ROD
BUSHING
SET SCREW
LOCK BOL T
LOWER
CANOPY
MOTOR UNIT
BLADE SUPPORT
BRACKET
GREEN
GREEN
WHITE
BLACK
OUTLET BOX
UPPER CANOPY
SPRING BUSHING
COTTER PIN
LOCK WASHER
SUPPLY NEUTRAL
NUT
BOLT
BLADE
BLADE
HOLDER
GASKET
FIGURE 1
SUPPLY
GROUND
SUPPLY HOT
FIGURE 2
HOW TO ASSEMBLE (FIGURE 1 shows fan parts.)
1. Locate upper canopy and remove two (2) screws holding fan
mounting bracket in canopy.
2. Locate down rod and remove spring bushing from hole inside of
rod and remove set screw from down rod.
3. (FIGURE 3) Place
upper canopy and lower canopy on down
rod by placing upper canopy over down rod with open end to-
ward plastic ball hanger. Place lower canopy over down rod with
open end facing away from plastic ball hanger.
4. Replace spring bushing into hole inside of down rod.
5. (FIGURE 4) Thread the
wire from the bushing through the down
rod by feeding the white, black and green supply wires from
motor through the bushing in the down rod and up through the
down rod.
6. Remove cotter pin from bolt on motor shaft. Remove nut, washers and bolt from motor shaft. Slide end of down rod over plastic
sleeve on motor shaft so that holes in down rod line up with hole
in motor shaft. (Replace bolt, flat washer, lockwasher, nut and
cotter pin). IMPORT ANT: Tighten nut until lockwasher is fully
compressed. No play or wiggle should be evident between the
down rod and the shaft. Bend out ends of cotter pin to secure.
Replace and tighten set screw into down rod that was removed
from Step 2.
7. Position lower canopy over motor shaft and wiring until it stops
and secure with set screw.
8. Blades may be installed at this time.
PFC-48 / PFC-56 Remove the two screws, lockwashers, and
blade support bracket from motor housing. Leave fiber board
gasket in place on motor housing. Place blade, with mounting
bracket up, over the gasket and replace the screws, lockwashers,
and blade support bracket. Tighten securely. Repeat for each
blade.
9. Place black rubber spacers in between the fan hanger bracket
and the 4” metal box. Mount the fan hanger bracket to the 4” box
marked for fan support. Use the mounting screws or hardware
provided with the ceiling box. IMPORT ANT : The ceiling box must
be marked as acceptable for fan support. The box should be
securely fastened to the structure so that it will support at least 35
lbs. Supply wiring, 120V, 60 Hz, should be run through a wall
switch to the outlet box.
10. Lift fan and place the ball hanger of the fan into the mounting
bracket. Rotate down rod until slot in ball hanger engages tab of
mounting bracket.
1 1.Cut off excess length of motor leads allowing 6” of lead to extend
into the outlet box. Strip leads approximately 1/4”.
12.(FIGURE 2) Connect fan leads to house supply wires using Listed
wire connectors. Connect white to white, black to black, and green
ground wires from fan and from mounting bracket to the supply
ground. After splice connections are made, turn splices upward
and carefully push into outlet box with green and white leads on
one side of the box and the black leads on the other side of the
box.
13.(FIGURE 5) Raise the
upper canopy up to the mounting bracket
and secure using the two screws removed earlier.
14. Restore electrical power and check for proper operation of the
fan.
IMPORTANT SAFEGUARDS
1.Be sure fan is switched off before cleaning it.
2. Keep hands, clothing and other objects away from moving fan
blades.
3.Exercise close supervision of children if they are present when fan
is operating.
4.Shut off electricity to fan before servicing or working near fan.
5.Do not operate fan if it has been damaged in any manner. Contact
your nearest NuTone Authorized Service Center.
UPPER
CANOPY
WIRES
DOWN
ROD
BUSHING
WIRES
LOWER
CANOPY
FIGURE 3 FIGURE 4
UPPER
CANOPY
FIGURE 5
WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that
such products will be free from defects in materials or workmanship for a period of two (2)) years
from the date of original purchase. THERE ARE NOOTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE.
During this two year period, NuTone will, at its option, repair or replace, without charge, any
product or part which is found to be defective under normal use and service. THIS WARRANTY
DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES. This warranty does not
cover (a) normal maintenance and service or (b) any products or parts which have been subject to
misuse, negligence, accident, improper maintenance or repair (other than by NuTone), faulty
installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the two year period as specified for the express
warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above
limitation may not apply to you.
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. NUTONE SHALL
NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT
OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have
other rights, which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the
address stated below or telephone 1/800-543-8687, (b) give the model number and part
identification and (c) describe the nature of any defect in the product or part. At the time of
requesting warranty service, you must present evidence of the original purchase date.
Date of Installation Builder or Installer
Model No. and Product Description
Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field
Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599.
Residents of Canada should write to: Broan-NuTone Canada, 1140 Tristar Drive,
Mississauga, Ontario, Canada L5T 1H9.
Two Year Limited Warranty
For the location of your nearest NuTone Independent Authorized Service Center:
Product model number • Date and Proof of purchase • The nature of the difficulty
IF YOU NEED ASSISTANCE OR SERVICE:
Residents of the contiguous United States Dial Free 1-800-543-8687
Please be prepared to provide:
Rev. 03/2001
99524445B